Overcasting is a new kind of dissimilar joining technique used to produce the aluminum（solid）/magnesium（liquid） bonding bi-metallic material in this study. For the Al/Mg（A390/AM60） bi-metallic samples, the inter...Overcasting is a new kind of dissimilar joining technique used to produce the aluminum（solid）/magnesium（liquid） bonding bi-metallic material in this study. For the Al/Mg（A390/AM60） bi-metallic samples, the interface microstructures are the research points, which directly influence the mechanical properties. It is, therefore, of vital importance to find a method to improve the interface microstructures. This research focused on the effect of the calcium（Ca） addition in the liquid Mg alloys and the heat treatment on the A390/AM60 interface microstructures of the bi-metallic samples. The testing results showed that, with Ca addition in AM60, owing to two possible reasons, the interface microstructure and the shear strength of the A390/AM60 bi-metallic samples could be improved. The heat treatment could further improve the interface microstructure and the mechanical properties by dissolving β-Mg_（17）Al_（12） into α-Mg and destroying the Mg_2Si layer structure.展开更多
This paper deals with the output improvement of heating and cooling cycle by using the work-fluid including phase change material.The experimental study is carried out by heat exchange between work-fluid and heat tran...This paper deals with the output improvement of heating and cooling cycle by using the work-fluid including phase change material.The experimental study is carried out by heat exchange between work-fluid and heat transfer surface.The work-fluid is flown to a high temperature or a low temperature heat transfer surface from the narrow path.In order to increase the amount of the heat transmission,a trace of Diethylether(boiling point 34.8 ℃),as a phase change material(PCM),is added to the work-fluid.The parameters of the experiment are additive amount of PCM,the rotational speed of the displacer piston and the temperature of heat transfer surface.It is clarified that the increasing of engine cycle output is brought by the PCM addition.The effect of PCM addition is evaluated by output ratio which is defined from the experimental cycle output data.The requirements for acquiring the increasing effect of output by adding PCM are clarified.展开更多
基金Funded by the National Natural Science Foundation of China(No.51571080)
文摘Overcasting is a new kind of dissimilar joining technique used to produce the aluminum（solid）/magnesium（liquid） bonding bi-metallic material in this study. For the Al/Mg（A390/AM60） bi-metallic samples, the interface microstructures are the research points, which directly influence the mechanical properties. It is, therefore, of vital importance to find a method to improve the interface microstructures. This research focused on the effect of the calcium（Ca） addition in the liquid Mg alloys and the heat treatment on the A390/AM60 interface microstructures of the bi-metallic samples. The testing results showed that, with Ca addition in AM60, owing to two possible reasons, the interface microstructure and the shear strength of the A390/AM60 bi-metallic samples could be improved. The heat treatment could further improve the interface microstructure and the mechanical properties by dissolving β-Mg_（17）Al_（12） into α-Mg and destroying the Mg_2Si layer structure.
基金the Cooperative Research Program of IOES,Institute of Ocean Energy,Saga University.(Accept15004A)
文摘This paper deals with the output improvement of heating and cooling cycle by using the work-fluid including phase change material.The experimental study is carried out by heat exchange between work-fluid and heat transfer surface.The work-fluid is flown to a high temperature or a low temperature heat transfer surface from the narrow path.In order to increase the amount of the heat transmission,a trace of Diethylether(boiling point 34.8 ℃),as a phase change material(PCM),is added to the work-fluid.The parameters of the experiment are additive amount of PCM,the rotational speed of the displacer piston and the temperature of heat transfer surface.It is clarified that the increasing of engine cycle output is brought by the PCM addition.The effect of PCM addition is evaluated by output ratio which is defined from the experimental cycle output data.The requirements for acquiring the increasing effect of output by adding PCM are clarified.
