HEAT TREATING OF SINTERED Fe-1.5Mo-0.7C STEELS AND THEIR SLIDING WEAR BEHAVIOR

The influence of heat treating on mechanical properties as well as on the sliding wear behavior of sintered Fe-1.5Mo-0.7C steels was experimentally studied. The microstruc-tures of sintered steels change from upper bainite to martensite, tempered martensite, pearlite and lower bainite depending on the heat treating conditions. Heat treating increases the hardness of sintered steels but high tempering temperature, i.e. 700℃, causes the hardness to be even lower than that of the as-sintered ones. The impact energy of sintered steels increases with increasing tempering temperature and arrives the highest at 700℃, while the steels tempered at 200℃ have the highest transverse rupture strength. Austempering results in fair good overall properties, such as hardness, impact energy, and transverse rupture strength. When the sintered steels were austempered, oil-quenched or tempered below 400? after quenched, the wear coefficient becomes considerably lower. Fair high hardness, such as HV30 】 380, and structures of martensite, tempered martensite or lower bainite are beneficial to lowering the wear coefficient. Under the wear test conditions given, delamination and oxidational wear are the main wear regimes for sintered Fe-1.5Mo-0.7C steels. Fe3O4 in the wear debris is beneficial to lowering wear coefficient.

Effect of roller shapes on strip buckling in a continuous annealing furnace

The effect of roller shapes on strip buckling in a continuous annealing furnace was focused on. The tensile stress distribution, the transverse compressive stress, and the critical buckling stress of the strip were studied by the finite element method （FEM） when the flat roller, crown roller, single taper roller, and double taper roller were used, respectively. Simulation results show that strip buckling is most likely to occur with the crown roller, then the double taper roller, and finally the single taper roller. Also, strip buckling can not occur when the flat roller is used. Considering strip snaking, the single taper roller and double taper roller are suggested in the continuous annealing fur-nace. The double taper roller with a better strip snaking-prevention ability should be applied in the sections with high strip temperature, and the single taper roller with a better buckling-prevention ability should be used in the sections with low strip temperature.

Development of microalloyed steels for high temperature carburizing

The potential for use of microalloy additions to suppress abnormal austenite grain growth and produce steels with enhanced bending fatigue resistance after high temperature vacuum carburizing was investigated in a series of Ti-modified SAE 8620 steels with w(niobium) additions up to 0.1%.Results are considered from a series of papers at the Advanced Steel Processing and Products Research Center on the effects of Nb content,heating rate, rolling history,and processing temperature on the evolution of austenite grain structures in carburizing steels. Emphasis is placed on understanding the effects of alloying and processing on each stage in the annealing process including the as received laboratory rolled conditions,during the onset of carburizing after annealing at different heating rates,and after annealing for various times at carburizing temperatures up to 1 100℃.Heating rate to the carburizing temperature was shown to be an influential variable and suppression of abnormal grain growth was dependent on the development of a critical distribution of fine NbC precipitates,stable at the austenitizing temperature.The importance to industrial carburizing practice of heating rate effects on precipitates and austenite grain size evolution are discussed and correlated to selected data on fatigue performance.

Effect of Prior Austenite Grain Size on the Morphology and Mechanical Properties of Martensite in Medium Carbon Steel

In industrial application,unintentional manufacturing line troubles often consequence in heating raw materials excessively,in terms of either time or temperature.One of the effects of such occurrence is a product with a variation of prior austenite grain size,even if after the heat treatment the end result is the same,martensite.The variation of the prior austenite grain size is believed to vary the end results of the martensite.This undesirable variation includes the variation of fatigue resistance,impact strength,yield strength,hardness,etc.This research studies the effect of the prior austenite grain size on the morphology of the martensite microstructure.The results show that within the typical industrial application of temperature and holding time set up,as holding time or the temperature increases,the prior austenite average diameter increases.The block and packet sizes in the martensite also increase.The variation of mechanical property dependence on the grain size is indeed due to the different characteristics reflected in the martensite morphology.With respect to the same area,smaller grain has more blocks and packets,which agrees with higher dislocation density verified with transmission electron microscopic evaluation.