By utilizing the current finite element program ANSYS, two types of finite element models (FEM), the beam model (BM) and shell model (SM), are established for the nonlinear stability analysis of a practical rigid fram...By utilizing the current finite element program ANSYS, two types of finite element models (FEM), the beam model (BM) and shell model (SM), are established for the nonlinear stability analysis of a practical rigid frame bridge—Longtanhe Great Bridge. In these analyses, geometrical and material nonlinearities are simultaneously taken into account. For geometrical nonlinearity, updated Lagrangian formulations are adopted to derive the tangent stiffness matrix. In order to simulate the nonlinear behavior of the plastic hinge of the piers, the multi lines spring element COMBIN39 is used in the SM while the bilinear rotational spring element COMBIN40 is employed in the BM. Numerical calculations show that satisfying results can be obtained in the stability analysis of the bridge when the double coupling nonlinearity effects are considered. In addition, the conclusion is significant for practical engineering.展开更多
Though the lengthened shrink-fit holder (LSFH) is widely applied in high speed milling of the parts characterized by deep cavities at present, its design and selection mainly depends on the experience and lacks a corr...Though the lengthened shrink-fit holder (LSFH) is widely applied in high speed milling of the parts characterized by deep cavities at present, its design and selection mainly depends on the experience and lacks a correct theoretical guidance. In this paper, attention is focus on the radial grip rigidity of the matching of LSFH and cutter in high speed milling. Based on the experiment modal analysis (EMA) technique, an accurate finite element model of the matching of LSFH and cutter is established firstly. Subsequently, the influence of different interference, grip length and spindle speed on the grip rigidity of LSFH are analyzed. The analysis results show that there is a reasonable interference and grip length between the LSFH and cutter so that to have a steepless grip and have a good radial grip rigidity and at the same time to avoid the strength of LSFH to exceed it’s yield limit which will reduce the precision and service life of LSFH, besides when spindle speed reach a extension the weakening influence of the centrifugal force on the radial grip rigidity of the matching of LSFH and cutter should been taken into account. Finally, the finite element analysis results are verified based on the construction of measurement method of the grip rigidity and the results fit very well. The studies provide a theoretical basis for the design, selection and the serialization and standardization of the matching of LSFH and cutter.展开更多
文摘By utilizing the current finite element program ANSYS, two types of finite element models (FEM), the beam model (BM) and shell model (SM), are established for the nonlinear stability analysis of a practical rigid frame bridge—Longtanhe Great Bridge. In these analyses, geometrical and material nonlinearities are simultaneously taken into account. For geometrical nonlinearity, updated Lagrangian formulations are adopted to derive the tangent stiffness matrix. In order to simulate the nonlinear behavior of the plastic hinge of the piers, the multi lines spring element COMBIN39 is used in the SM while the bilinear rotational spring element COMBIN40 is employed in the BM. Numerical calculations show that satisfying results can be obtained in the stability analysis of the bridge when the double coupling nonlinearity effects are considered. In addition, the conclusion is significant for practical engineering.
基金supported by National Hi-tech Research and Development Program of China (863 Program, Grant No. 2009AA44302)Scientific Research Fund of Hunan Provincial Education Department, China (Grant No. 10C1259)+2 种基金Hunan Provincial Planned Science and Technology Project of China (Grant No. 2011FJ3231)National Natural Science Foundation of China (Grant No. 51005194)Open Innovation Platform of Hunan College Fund, China (Grant No. 10K063)
文摘Though the lengthened shrink-fit holder (LSFH) is widely applied in high speed milling of the parts characterized by deep cavities at present, its design and selection mainly depends on the experience and lacks a correct theoretical guidance. In this paper, attention is focus on the radial grip rigidity of the matching of LSFH and cutter in high speed milling. Based on the experiment modal analysis (EMA) technique, an accurate finite element model of the matching of LSFH and cutter is established firstly. Subsequently, the influence of different interference, grip length and spindle speed on the grip rigidity of LSFH are analyzed. The analysis results show that there is a reasonable interference and grip length between the LSFH and cutter so that to have a steepless grip and have a good radial grip rigidity and at the same time to avoid the strength of LSFH to exceed it’s yield limit which will reduce the precision and service life of LSFH, besides when spindle speed reach a extension the weakening influence of the centrifugal force on the radial grip rigidity of the matching of LSFH and cutter should been taken into account. Finally, the finite element analysis results are verified based on the construction of measurement method of the grip rigidity and the results fit very well. The studies provide a theoretical basis for the design, selection and the serialization and standardization of the matching of LSFH and cutter.
