The independently designed and manufactured ultra-high-strength aluminum alloy Al-12.18 Zn-3.31 Mg-1.43 Cu-0.20 Zr-0.04 Sr was investigated via scanning electron microscopy observations, X-ray diffraction analysis, ha...The independently designed and manufactured ultra-high-strength aluminum alloy Al-12.18 Zn-3.31 Mg-1.43 Cu-0.20 Zr-0.04 Sr was investigated via scanning electron microscopy observations, X-ray diffraction analysis, hardness tests, electrical conductivity tests, tensile tests, intergranular corrosion tests, and exfoliation corrosion tests. The effect of pre-recovery on the microstructure and mechanical properties of this aluminum alloy was also studied. The results show that the pre-recovery heat treatment releases deformation energy, inhibits recrystallization, and decreases the dislocation density. Although the pre-recovery heat treatment has little effect on the hardness, electrical conductivity, and elongation of this aluminum alloy, it can dramatically improve the alloy's tensile strength(the maximum tensile strength increased from 785.0 MPa to 809.2 MPa). Moreover, the tensile properties of this aluminum alloy have a certain degree of isotropy, and the pre-recovery heat treatment does not affect this property. In addition, the rolled aluminum alloy exhibits good corrosion resistance, but the effect of the pre-recovery heat treatment on the alloy's resistance to intergranular and exfoliation corrosion is negligible.展开更多
The improvements of microstructures and properties of a high strength aluminum cast alloy were studied. The effects of rare earth elements on the microstructures and mechanical properties of the high strength cast all...The improvements of microstructures and properties of a high strength aluminum cast alloy were studied. The effects of rare earth elements on the microstructures and mechanical properties of the high strength cast alloy Al-Cu-Mg-Si were investigated. The result shows that the addition of rare earth elements can change the microstructures in refining the grain size of the alloy and making the needle-like and laminar eutectic Si to a granular Si. With the increase of the rare earth, the tensile strength and elongation of the alloy increase first and then fall down. The mechanical properties of the alloy will reach the highest value when the content of rare earth elements is about 0.7%.展开更多
Dissimilar material joining of 6008 aluminum alloy to H220 YD galvanized high strength steel was performed by resistance spot welding with especial electrodes that were a flat tip electrode against the steel surface a...Dissimilar material joining of 6008 aluminum alloy to H220 YD galvanized high strength steel was performed by resistance spot welding with especial electrodes that were a flat tip electrode against the steel surface and a domed tip electrode upon the aluminum alloy surface. An intermetallic compound layer composed of Fe2Al5 and FeAl3 was formed at the steel/ aluminum interface in the welded joint. The thickness of the intermetallic compound layer increased with increasing welding current and welding time, and the maximum thickness being 7. 0 μm was obtained at 25 kA and 300 ms. The weld nugget diameter and tensile shear load of the welded joint had increased tendencies first with increasing welding current （ 18 -22 kA） and welding time （ 50 - 300 ms）, then changed little with further increasing welding current （ 22 - 25 kA） and welding time （300 -400 ms）. The maximum tensile shear load reached 5.4 kN at 22 kA and 300 ms. The welded joint fractured through brittle intermetallic compound layer and aluminum alloy nugget.展开更多
基金financially supported by the Jiangsu Provincial Industrial Science and Technology Support Program (No. BE2008118)the Basic Research on Isotropic Ultra-high Strength Aluminum Matrix Composite (No. 6140922010201)
文摘The independently designed and manufactured ultra-high-strength aluminum alloy Al-12.18 Zn-3.31 Mg-1.43 Cu-0.20 Zr-0.04 Sr was investigated via scanning electron microscopy observations, X-ray diffraction analysis, hardness tests, electrical conductivity tests, tensile tests, intergranular corrosion tests, and exfoliation corrosion tests. The effect of pre-recovery on the microstructure and mechanical properties of this aluminum alloy was also studied. The results show that the pre-recovery heat treatment releases deformation energy, inhibits recrystallization, and decreases the dislocation density. Although the pre-recovery heat treatment has little effect on the hardness, electrical conductivity, and elongation of this aluminum alloy, it can dramatically improve the alloy's tensile strength(the maximum tensile strength increased from 785.0 MPa to 809.2 MPa). Moreover, the tensile properties of this aluminum alloy have a certain degree of isotropy, and the pre-recovery heat treatment does not affect this property. In addition, the rolled aluminum alloy exhibits good corrosion resistance, but the effect of the pre-recovery heat treatment on the alloy's resistance to intergranular and exfoliation corrosion is negligible.
基金This work was financially supported by the Fund of BeijingJiaotong University(No.2004SZ006).
文摘The improvements of microstructures and properties of a high strength aluminum cast alloy were studied. The effects of rare earth elements on the microstructures and mechanical properties of the high strength cast alloy Al-Cu-Mg-Si were investigated. The result shows that the addition of rare earth elements can change the microstructures in refining the grain size of the alloy and making the needle-like and laminar eutectic Si to a granular Si. With the increase of the rare earth, the tensile strength and elongation of the alloy increase first and then fall down. The mechanical properties of the alloy will reach the highest value when the content of rare earth elements is about 0.7%.
文摘Dissimilar material joining of 6008 aluminum alloy to H220 YD galvanized high strength steel was performed by resistance spot welding with especial electrodes that were a flat tip electrode against the steel surface and a domed tip electrode upon the aluminum alloy surface. An intermetallic compound layer composed of Fe2Al5 and FeAl3 was formed at the steel/ aluminum interface in the welded joint. The thickness of the intermetallic compound layer increased with increasing welding current and welding time, and the maximum thickness being 7. 0 μm was obtained at 25 kA and 300 ms. The weld nugget diameter and tensile shear load of the welded joint had increased tendencies first with increasing welding current （ 18 -22 kA） and welding time （ 50 - 300 ms）, then changed little with further increasing welding current （ 22 - 25 kA） and welding time （300 -400 ms）. The maximum tensile shear load reached 5.4 kN at 22 kA and 300 ms. The welded joint fractured through brittle intermetallic compound layer and aluminum alloy nugget.
