Effect of Heat Treatment on Delayed Fracture Resistance of High Strength Steel 30CrMnSi2NiNb

The steel specimens of nominal composition 0.3C-1.0Cr-1.0Mn-2.0Si-1.0Ni-0.04 Nb were quenched and tempered or isothermally quenched from various temperatures.It is found that the steel quenched and tempered with a tensile strength of 1 500-1 600 MPa has a KISCC（critical stress intensity factor） value below 15.0 MPa · m1/2.The steel isothermally quenched with a tensile strength of 1 350-1 750 MPa has a KISCC value about 20.0 MPa·m1/2.In addition,with increase of isothermal quenching temperature,the tensile strength decreases greatly and KISCC value does not pronouncedly change.The microstructure of isothermally quenched specimens is composed of bainite and retained austenite.The delayed fracture resistance is dependent on the stability of austenite,which is in turn related to the retained austenite volume fraction and carbon content in austenite.

Microstructure and mechanical property of resistance spot welded joint of aluminum alloy to high strength steel with especial electrodes

Dissimilar material joining of 6008 aluminum alloy to H220 YD galvanized high strength steel was performed by resistance spot welding with especial electrodes that were a flat tip electrode against the steel surface and a domed tip electrode upon the aluminum alloy surface. An intermetallic compound layer composed of Fe2Al5 and FeAl3 was formed at the steel/ aluminum interface in the welded joint. The thickness of the intermetallic compound layer increased with increasing welding current and welding time, and the maximum thickness being 7. 0 μm was obtained at 25 kA and 300 ms. The weld nugget diameter and tensile shear load of the welded joint had increased tendencies first with increasing welding current （ 18 -22 kA） and welding time （ 50 - 300 ms）, then changed little with further increasing welding current （ 22 - 25 kA） and welding time （300 -400 ms）. The maximum tensile shear load reached 5.4 kN at 22 kA and 300 ms. The welded joint fractured through brittle intermetallic compound layer and aluminum alloy nugget.

Prediction and Verification of Resistance Spot Welding Results of Ultra-High Strength Steels through FE Simulations

Resistance spot welding (RSW) is the most common welding method in automotive engineering due to its low cost and high ability of automation. However, physical weldability testing is costly, time consuming and dependent of supplies of material and equipment. Finite Element (FE) simulations have been utilized to understand, verify and optimize manufacturing processes more efficiently. The present work aims to verify the capability of FE models for the RSW process by comparing simulation results to physical experiments for materials used in automotive production, with yield strengths from approximately 280 MPa to more than 1500 MPa. Previous research has mainly focused on lower strength materials. The physical weld results were assessed using destructive testing and an analysis of expulsion limits was also carried out. Extensive new determination of material data was carried out. The material data analysis was based on physical testing of material specimens, material simulation and comparison to data from literature. The study showed good agreement between simulations and physical testing. The mean absolute error of weld nugget size was 0.68 mm and the mean absolute error of expulsion limit was 1.10 kA.

Effect of laser heating on the microstructure and hardness of TRIP590advanced high strength steel used for roll forming

TRIP590 advanced high strength steel sheets were heated by laser with different powers.Changes of the microstructure and the hardness of TRIP590 steel under laser heating with different powers were investigated by metallographic microscope,scanning electron microscope,and hardness tester.The purpose was to study the effect of laser power on microstructure and hardness of TRIP590 steel.It is shown that the power of laser plays an important role on the microstructure and hardness of heated steel sheets.The results are helpful to determine suitable power for the laser auxiliary forming of Trip590 steel in order to obtain uniform microstructure and high hardness.

Influence of rapid heating process on the microstructure and tensile properties of high-strength ferrite–martensite dual-phase steel

Three low-carbon dual-phase （DP） steels with almost constant martensite contents of 20vo1% were produced by intercritical annealing at different heating rates and soaking temperatures. Microstructures prepared at low temperature （1043 K, FH1） with fast-heating （300 K/s） show banded ferrite/martensite structure, whereas those soaked at high temperature （1103 K, FH2） with fast heating reveal blocky martensite uniformly distributed in the fine-grained ferrite matrix. Their mechanical properties were tested under tensile conditions and compared to a slow-heated （5 K/s） reference material （SH0）. The tensile tests indicate that for a given martensite volume fraction, the yield strength and total elongation values are noticeably affected by the refinement of ferrite grains and the martensite morphology. Metallographic observations reveal the formation of microvoids at the ferrite/martensite interface in the SH0 and FH2 samples, whereas microvoids nucleate via the fracture of banded martensite particles in the FH1 specimen. In addition, analyses of the work-hardening behaviors of the DP microstructures using the differential Crussard-Jaoul technique demonstrate two stages of work hardening for all samples.

Effects of tungsten on the oxidation resistance and high-temperature strength of 18CrNbTi ferritic stainless steel

18CrNbTi ferritic stainless steel is a low-cost material mainly used for the fabrication of manifolds, which usually work at temperatures below 950℃. With the development of engine technology, exhaust manifolds tend to work above 1 000 ℃ and this may be even higher in the future. For developing a new kind of steel to satisfy these requirements,the effects of tungsten （W）addition on the high-temperature strength and oxidation resistance of 18CrNbTi ferritic stainless steel are discussed in this study. The test results show that W enhances high-temperature strength at 1 000 ℃ and significantly improves oxidation resistance. However, W addition tends to degrade oxide layer adhesion,causing spalling during alternate hot and cold conditions.

Effect of Heat Treatment on Microstructure and Mechanical properties of high strength low alloy(HSLA)steel

In this paper,a Fe-based Mn-Ni–Cr–Mo high strength low alloy(HSLA)steel was prepared by using Vacuum melting,following by hot rolling with 78%deformation and various heat treatment processes.Microstructure were characterized by optical microscope(OM),scanning electron microscope(SEM)equipped with energy dispersive spectrometer.Tensile tests were performed.After direct quenching(Q)from 860℃,the samples were subjected to secondary quenching(L)at different intercritical temperatures within the two-phase region and various tempering temperatures(T).Results show that QLT treatment increases elongation and decreases yield ratio compared with conventional quenching and tempering process(QT).The optimum QLT heat treatment parameter in terms of temperature are determined as Q:860℃,L:700℃,and T:600℃,resulting in the better combined properties with yield strength of 756MPa,tensile strength of 820MPa,tensile elongation of 16.76%and yield ratio of 0.923.

Effect of Boron on Delayed Fracture Resistance of Medium-Carbon High Strength Spring Steel

The delayed fracture behavior of medium carbon high strength spring steel containing different amounts of boron （0. 000 5%, 0. 001 6 %） was studied using sustained load delayed fracture test. The results show that delayed fracture resistance of boron containing steels is higher than that of conventional steel 60Si2MnA at the same strength level and it increases with the increase of boron eontent from 0. 000 5% to 0. 001 6%. The delayed fracture mode is mainly intergranular in the boron containing steels tempered at 350℃, which indicates that the addition of boron does not change the fracture character. However, the increase of boron content enlarges the size of the crack initia tion area. Further study of phase analysis indicates that most boron is in solid solution, and only a very small quantity of boron is in the M3 （C, B） phase.

High Strength and Heat Resistance of Low-RE-Containing Mg Alloy Achieved via Substantial Dynamic Precipitates

Conventional high-strength Mg-RE-based wrought alloys usually contain a high amount of RE solutes,which largely increases the alloy cost and thus restricts their adoptions.In this work,we developed a low-RE-containing Mg-3Sm-1Nd-0.6Zn-0.4Zr alloy by hot extrusion with low extrusion ratio,which shows a high tensile yield strength(TYS)of 435 MPa and a satisfactory elongation of 5.6%at room temperature,outperforming most Mg-Gd-Y-based extrusion alloys with RE contents of 12 wt%at least.Outstanding high-temperature strength,such as the TYS of 280 MPa at 200℃ and 251 MPa at 250℃,is also obtained in this alloy.The alloy presented a typical bimodal grain structure including coarse hot-worked grains with a strong texture and fine recrystallized grains with random orientations.Also,abundant Mg3RE particles were mostly introduced in hot-worked grains and at recrystallized grain boundaries by dynamic precipitation during extrusion.Consequently,the high strength of this alloy is principally attributed to the combined hardening effect of numerous Mg_(3)RE particles,fine recrystallized grains,and strongly textural hot-worked grains,rather than the ultra-strong age-hardening effect in traditional high RE-alloyed Mg alloys.

Microstructure evolution and corrosion resistance in simulated CGHAZ of X80 high-deformability pipeline steel

In this study, the microstructure evolution and corrosion resistance in O. 5 M Na2CO3 - 1 M NaHCO3 solution of X80 high-deformability （ X8OHD ） pipeline steel coarse-grained heat-affected zone （CGHAZ） with several heat input levels were investigated. It is shown that the microstructure of CGHAZ changes from bainite ferrite to granular bainite as the heat input increasing. In addition, the corrosion resistance and the stability of passive film of base material are better than those of CGHAZ with several heat input levels. Too small or too big heat input is inadvisable and better corrosion resistance of CGHAZ is attained when heat input is 30 kJ/cm.

Laser Beam Welding of 600 MPa Quenched and Tempered High-Strength Steel

Conventional fusion arc welding of high-strength quenched and tempered steel can be improved through the use of non-conventional laser beam welding. This article presents the investigations of autogenous bead on plate and butt CO2 Laser Welding (LW) of 7 mm thick high-strength quenched and tempered low alloy SM570 (JIS) steel plates. The influence of laser welding parameters, mainly welding speed, defocusing distance and shielding gas flow rate on the weld profile, i.e., weld zone penetration depth and width, microstructure and mechanical properties of welded joints was determined. All welded joints showed smooth and uniform weld beads free from superficial porosity and undercuts. The selected best welding conditions were a laser power of 5.0 kW, welding speed of 500 mm/min, argon gas shielding flow rate of 30 L/min and a defocusing distance of -0.5 mm. It was observed that these conditions gave complete penetration and minimized the width of the weld bead. The microstructure of the welded joints was evaluated by light optical microscopy. The weld metal (WM) and heat-affected zone (HAZ) near weld metal achieved maximum hardness (355 HV). The tensile fractured samples showed the ductile mode of failure and ultimate tensile strength of 580 MPa.

Development of a New Kind of High Strength Spring Steel

A new kind of high strength, high toughness and high plasticity spring steel has been developed. The strength, the reduction of area and the elongation of the steel are all higher than those of the steel 60Si2CrVA. The decarburization resistance and the sag resistance are also higher than those of the steel 60Si2CrVA. It has good hardenability, and is suitable for making springs with big cross section. The bogie springs made of this kind of steel have passed 2×106 cycles without broken under the conditions of maximum stress of 906 MPa and the minimum stress of 388 MPa.

The welding application of high strength steels used in engineering machinery

With the rapid development of low alloy steel strength level,more problems caused by welding are exposed day by day.Recently,the efforts have been paid to improve or enchance the low toughness of heated affected zone and welded metal which can enchance the comprehensive mechanical properties that is the core scientific problems of its safe operation by researching crack initiation and crack propragation attracted a rapidly growing interest.This article focuses on the research status and progress of welding technology and joint microstructure and properties of advanced steel materials.The influence of shielding gas on the microstructure evolution of deposited metals,the effect heat input of welded joint performance,interpass temperature and alloy elements on welded joints microstructure and M-A constituent evolution and properties are reviewed in detail.And for the heat affected zone,the grain size and microstructure as well as the shape,size,and distribution of M-A constituent,have a significant impact on the impact toughness.This paper is an attempt to review the effect of different welding process parameters on welded metal and HAZ of HSLA steels.

IMPROVEMENT OF TYPE IV CRACKING RESISTANCE OF 9Cr HEAT RESISTING STEEL WELDMENT BY BORON ADDITION

Creep lives of high Cr ferritic heat resisting steel weldments decrease due to Type Ⅳ fracture, which occurs as a result of formation and growth of creep voids and cracks on grain boundaries in fine-grained heat affected zone (HAZ). Because boron is considered to suppress the coarsening of grain boundary precipitates and growth of creep voids, we have investigated the effect of boron addition on the creep properties of 9Cr steel weldments. Four kinds of 9Cr3WSCoVNb steels with boron content varying from 4.7×10-5 to 1.8×10-4 and with nitrogen as low as 2.0×10-5 were prepared. The steel plates were welded by gas tungsten arc welding and crept at 923K. It was found that the microstructures of HAZ were quite different from those of conventional high Cr steels such as P91 and P92, namely the fine-grained HAZ did not exist in the present steel weldments. Boron addition also has the effect to suppress coarsening of grain boundary carbides in HAZ during creep. As a result of these phenomena, the welded joints of present steels showed no Type Ⅳ fractures and much better creep lives than those of conventional steels.

MICROSTRUCTURE AND MECHANICAL PROPERTY DEVELOPMENT IN THE SIMULATED HEAT AFFECTED ZONE OF V TREATED HSLA STEELS

The simulated heat affected zone （HAZ） of the high strength low alloy （HSLA） steels containing 0%, 0.047%, 0.097% and 0.151% vanadium, respectively, were studied with Gleeble-2000 thermomechanical simulator to determine the influence of vanadium addition on the mechanical properties of the HAZ. The HAZ simulation involved reheating the samples to 1350℃, and then cooling to ambient temperature at a cooling rate of 5℃/s ranging from 800 to 500℃ （△8/5=60s）. The mechanical properties including tensile strength and -20℃ impact toughness were conducted. The microstructures of the base steel and the simulated HAZs were investigated using optical microscope, scanning electron microscope （ SEM ） and transmission electron microscope （TEM）. Based on the systemutic examination, the present work confirmed that about 0.05% vanadium addition to low carbon low alloy steels resulted in expected balance of strength and toughness of the HAZ. And more than 0.10% levels addition led to detrimental toughness of the HAZ SEM study showed that the simulated 0.097% and 0.151%V HAZs consisted of more coarse ferrite plates with greater and more M-A constituents along austenite grain and ferrite plate bound- aries. The impact fracture surfaces of the simulated 0.097% and 0.151%V HAZs showed typically brittle mode with predominant cleavages. The size of the facet in the fracture surface increased with increasing vanadium level from 0.097% to 0.151%.As a result, the simulated 0.151% V HAZ has the lowest impact toughness of the four specimens.

Interfacial characterization of resistance spot welded joint of steel and aluminum alloy

The dissimilar material resistance spot welding of galvanized high strength steel and aluminum alloy had been conducted. The welded joint exhibited a thin reaction layer composed of Fe2Al5 and Fe4Al13 phases at steel/aluminum interface. The welded joint presented a tensile shear load of 3.3 kN with an aluminum alloy nugget diameter of 5.7 mm. The interfacial failure mode was observed for the tensile shear specimen and fracture occurred at reaction layer and aluminum alloy fusion zone beside the interface. The reaction layer with compounds was the main reason for reduction of the welded joint mechanical property.

Austenite grain growth behavior of Q1030 high strength welded steel

The austenite grain growth behavior of Q1030 steel was studied under different heating conditions. The austenite grain size increases with the heating temperature and holding time increasing. Austenite grains grow in an exponential manner with rising heating tem- perature and in a parabolic manner with prolonging holding time. A mathematical model for describing the austenite grain growth behavior of Q 1030 steel was obtained on the basis of experimental results using regression analysis. When the heating temperatures lie between 1000 and 1100℃ at a certain holding time, abnormal grain growth appears, which causes mixed grains in Q1030 steel.

Corrosion behavior of high-strength spring steel for high-speed railway

The corrosion resistance and evolution of corrosion products in medium-carbon high-strength spring steels were investigated in a neutral salt spray(5 wt% Na Cl solution). A formation model of γ-Fe OOH and a transformation model describing the conversion of γ-Fe OOH to α-Fe OOH were constructed. The results indicated that, at the initial corrosion stage, the corrosion resistance was gradually improved with the addition of Cr; however, with the addition of alloying element V, the corrosion resistance decreased. These results were attributed mainly to the initial corrosion stage being closely related to the matrix microstructure parameters such as grain-boundary character and dislocation density. After the rust layer was formed at a later corrosion stage, the corrosion resistance was reinforced with the addition of Cr and V because Cr strongly influenced the composition, structure, and morphology of the corrosion products. The results presented herein show that Cr was conducive to the transformation of γ-Fe OOH into α-Fe OOH. Moreover, V and Cr exhibited obvious synergy and were enriched in the inner layer of the corrosion products.

High-temperature oxidation behavior of heat resistant stainless steel 1.4828

The kinetic curves of the high-temperature oxidation of austenitic heat resistant stainless steel 1. 4828 at 1 050 ℃ were measured using a weighing method. It is shown that the oxidation curves at 1 050 ℃ followed the parabolic line law, and after 250 h of oxidation, the mass gain was about 80 g/m2. The surface morphology and structure of the oxide layers were studied by scanning electron microscopy and X-ray diffraction. A complicated oxide layer obtained at 1 050 ℃ was mainly composed, from inner to outer, of （FeSi） 3 04, Cr2 03, Fe2 03, and spinel oxides FeCr204 and NiMn204.