A suitable carburized microstructure with fine granular dispersed carbides in hypereutectoid zone,ultra fine martensite in matrix and recrystallized austenite to be refined to the grain size of 12~14 has been obtaine...A suitable carburized microstructure with fine granular dispersed carbides in hypereutectoid zone,ultra fine martensite in matrix and recrystallized austenite to be refined to the grain size of 12~14 has been obtained by a new process,which is a high carbon concentration carburizing with rare earth element at low temperature(860~880℃)in a discontinuous gas carburization furnace.There was not much difference for the microstructure in eutectic zone between this and conventional process.Forming mechanism of granular carbides has been also studied in this paper.展开更多
An industrial plant trial for optimizing the process parameters in a round billet continuous casting mold with electromagnetic stirring (M-EMS) was performed, in which the influences of stirring parameters with M-EM...An industrial plant trial for optimizing the process parameters in a round billet continuous casting mold with electromagnetic stirring (M-EMS) was performed, in which the influences of stirring parameters with M-EMS on the solidification macrostructure of high carbon steel were investigated. The results show that the billet quality is not well controlled under the condition of working current and frequency with EMS, in which the subsurface crack of grade 1.0-2.0 ups to 38.09%, the central pipe of grade 1.0-1.5 reaches to 14.28%, and the central porosity of grade 1.5 is 14.29%. The parameters of current 260 A and frequency 8 Hz as the final optimum scheme has a remarkable effect for improving the macroscopic quality of billet, in which the subsurface crack, central pipe and skin blowhole are all disappeared, and the central porosity and carbon segregation are also well improved.展开更多
The effect of Cr/Mn segregation on the abnormal banded structure of high carbon bearing steel was studied by reheating and hot rolling.With the use of an optical microscope, scanning electron microscope, transmission ...The effect of Cr/Mn segregation on the abnormal banded structure of high carbon bearing steel was studied by reheating and hot rolling.With the use of an optical microscope, scanning electron microscope, transmission electron microscope, and electron probe microanalyzer, the segregation characteristics of alloying elements in cast billet and their relationship with hot-rolled plate banded structure were revealed.The formation causes of an abnormal banded structure and the elimination methods were analyzed.Results indicate the serious positive segregation of C, Cr, and Mn alloy elements in the billet.Even distribution of Cr/Mn elements could not be achieved after 10 h of heat preservation at 1200℃, and the spacing of the element aggregation area increased, but the segregation index of alloy elements decreased.Obvious alloying element segregation characteristics are present in the banded structure of the hot-rolled plate.This distinct white band is composed of martensitic phases.The formation of this abnormal pearlite–martensite banded structure is due to the interaction between the undercooled austenite transformation behavior of hot-rolled metal and the segregation of its alloying elements.Under the air cooling after rolling, controlling the segregation index of alloy elements can reduce or eliminate the abnormal banded structure.展开更多
The apparent morphologies of packet martensite in eight high carbon steels were researched by using optical microscope, scanning electron microscope, and transmission electron microscope. It was found that the apparen...The apparent morphologies of packet martensite in eight high carbon steels were researched by using optical microscope, scanning electron microscope, and transmission electron microscope. It was found that the apparent morphologies, substructures, and habit plane of packet martensite in high carbon steels are entirely different from that in low carbon steels; the substructures of packet martensite in high carbon steels possess fully twinned structure, while the substructures of individual coarse martensite plates in these steels bear both fully and partially twinned structures. The formation reason for apparent morphologies, substructures and two habit planes (i. e, { 111 }, and { 225}r) of high carbon martensite were discussed in detail.展开更多
Manuscript received 30 July 1999 Abstract The shielded metal arc welding (SMAW) of a manganese steel part as a crossing of railway track to a carbon steel part as the rails of the railroad is the welding of dissimil...Manuscript received 30 July 1999 Abstract The shielded metal arc welding (SMAW) of a manganese steel part as a crossing of railway track to a carbon steel part as the rails of the railroad is the welding of dissimilar steel. It are was known that it is not possible to the the rail of railroad directly to the cross- ing of railway track made from a steel containing about 14% of manganese (wt. ) because of so many differences between the two kinds of steels such as composition, microstructure,mechanical properties and weldability.A method was used to solve the problem by presetting an intermediate layer on each side of the joint and other special procedures were used.The result of test indicated that a good weld joint was obtained.展开更多
A certain quantity of RE is dissolved in high-carbon steel. The dissolved RE not only segregates on grain boundary, but also exists in grains. It exists in cementite much more than in ferrite. RE makes the carbides sp...A certain quantity of RE is dissolved in high-carbon steel. The dissolved RE not only segregates on grain boundary, but also exists in grains. It exists in cementite much more than in ferrite. RE makes the carbides spheroidal and fine, and the carbides distribute uniformly. RE also changes the morphology of pearlite. By means of the analysis of Auger energy spectrum, we find that RE, which is dissolved in cementite, changes the composition and structure of cementite. In the case of higher content of RE and carbon, RE carbide can be formed.展开更多
The present work employed the X-ray diffraction, scanning electron microscopy, electron backscattered diffraction, and electron probe microanalysis techniques to identify the microstructural evolution and mechanical a...The present work employed the X-ray diffraction, scanning electron microscopy, electron backscattered diffraction, and electron probe microanalysis techniques to identify the microstructural evolution and mechanical and abrasive behavior of high carbon steel during quenching-partitioning treatment with an aim to enhance the toughness and wear resistance of high carbon steel.Results showed that, with the increase in partitioning temperature from 250 to 400℃, the amount of retained austenite(RA) decreased resulting from the carbide precipitation effect after longer partitioning times.Moreover, the stability of RA generally increased because of the enhanced degree of carbon enrichment in RA.Given the factors affecting the toughness of high carbon steel, the stability of RA associated with size, carbon content, and morphology plays a significant role in determining the toughness of high carbon steel.The analysis of the wear resistance of samples with different mechanical properties shows that hardness is the primary factor affecting the wear resistance of high carbon steel, and the toughness is the secondary one.展开更多
Felt base carbon/carbon composites fabricated by super-high pressure impregnation carbonization process (SPIC) were heat treated at high temperature 2773K. The oxidation properties of felt base carbon/carbon composite...Felt base carbon/carbon composites fabricated by super-high pressure impregnation carbonization process (SPIC) were heat treated at high temperature 2773K. The oxidation properties of felt base carbon/carbon composites were investigated at different temperatures (773-1173K), and the microstructures of carbon/carbon composites were studied by SEM and X-ray diffraction. The experimental results showed that the inter-laminar distance of (002) plane (d002) deceased while the microcrystalline stack height (Lc) increased. The oxidation rate of felt base carbon/carbon composites was invari-able at certain temperatures. The oxidation mechanism of carbon/carbon composites changed remarkably at the oxidation temperature 973K. At the initial oxidation stage of carbon/carbon composites, carbon matrix was oxidized much more rapidly than carbon felt.展开更多
Effect of rare earth alloy modification on properties and microstructure of high carbon equivalent gray cast iron was investigated.The experimental results show that in the way of mechanical property,when the addition...Effect of rare earth alloy modification on properties and microstructure of high carbon equivalent gray cast iron was investigated.The experimental results show that in the way of mechanical property,when the addition of rare earth alloy is 0.2% and 0.3%,the tensile strength of cast iron increases.In the way of microstructure,the addition of rare earth alloy increases the number of primary austenite dendrites,reduces secondary dendritic arm spacing,and changes the eutectic size and quantity.When rare earth alloy is added into gray cast iron,the morphology and quantity of graphite play a major role on the improvement of tensile strength.展开更多
Antibodies to the ubiquitous group of stress proteins known as heat shock proteins (Hsps) have been found to be associated with a number of diseases in humans. Hsps are known to be induced by certain xenobiotics, some...Antibodies to the ubiquitous group of stress proteins known as heat shock proteins (Hsps) have been found to be associated with a number of diseases in humans. Hsps are known to be induced by certain xenobiotics, some of which are common in the working environment. The biological significance of the presence of such autoantibodies is presently unclear. In the present study, we used immunoblotting to investigate the presence of antibodies against the different stress proteins, Hsp27, Hsp60, Hsp71, Hse (heat shock cognate ) 73 and Hsp89a and D in groups of workers exposed to high temperature or carbon monoxide. These data were related to a detailed clinical evaluation and to various laboratory measurements including electrocardiogram (ECG), B echogram, white blood cell counts and typing, the activity of alanine aminotransferase (ALT), acid phosphatase (ACP) and alkaline phosphatase (ALP) and lymphocyte DNA damage. Antibodies to Hsp27 and Hsp71 were found more frequently in the high temperature and carbon monoxide-exposed groups than in controls (P (0.05 ). The carbon monoxide-exposed group showed the highest incidence of anti-Hsp antibodies. Anti-Hsp60 antibodies were only detected in workers exposed to high temperature or carbon monoxide. The percentage of workers with abnormal ECG, B echogram changes and displaying hepatitis B antigen (HBsAg ) was higher in the carbon monoxide group than in the control group (P<0.05 ).There was a significant inerease in the activity of ALT in the high temperature and carbon monoxide groups and in the activities of ACP and ALP in the carbon monoxide group (P<0.05 ). The extent of DNA damage measured in lymphoeytes was higher in workers from the high temperature and carbon monoxide-cxposed groups. We suggest that the increased frequeney of antibodies to Hsps is the result of these damages, of the release of denatured Hsps and of a decrease in the phagocytic ability of macrophages in these workers. The data gathered in the present study show a statistical relation between the occurrence of antibodies against Hsps and the frequency of health problems in workers and suggest a potential role for the antibodies as useful biomarkers to assess whether workers are experieneing environmental stress展开更多
The semi-solid high carbon steel T12 was rolled in a closed box groove under a certain condition by the rheo-rolling equipment, and the microstructural morphology of the semi-solid T12 before and after deformation wa...The semi-solid high carbon steel T12 was rolled in a closed box groove under a certain condition by the rheo-rolling equipment, and the microstructural morphology of the semi-solid T12 before and after deformation was investigated by optical mi- croscope to analyze and summarize the microstructure evolution law of T12 deformed in semi-solid state. The experiment results show that the grain shape before deformation of the semi-solid T12 steel displays globule or ellipse by the electromagnetic stirring, the distribution of solid and liquid phases is homogeneous. But the microstructure of semi-solid product after rheo-rolling exhibits macrosegregation that the distribution of liquid and solid phases changes, the liquid phases divorce from the solid phases. In the transverse section, most of the solid phases get together in the center of the specimen, the liquid phases flow to the surface or the edge of the specimen, and the grains occur plastic deformation while reduction increased. In longitudinal section, the middle micro- structure of the specimen is more homogeneous than that at the head or tail, the head microstructure is similar to the tail and the size of the grains is not homogeneous.展开更多
In this study,we have examined the effects of exposure to high temperature, carbon inonoxideor a combination of both conditions in a model system,the rat and in industrial workers.In the rat liver, HSP70 mRNA and HSP7...In this study,we have examined the effects of exposure to high temperature, carbon inonoxideor a combination of both conditions in a model system,the rat and in industrial workers.In the rat liver, HSP70 mRNA and HSP70 synthesis were measured by dot hybridization and western blot. The results showed that after a heat stress HSP70 mRNA and its product, HSP70 increased significantly and there was a synergism in the combined effects of high temperature and carbon monoxide exposure on the induction of HSP70 mRNA and HSP70 synthesis. Heat played a major role in this induction. The presence of antibodies to human HSP27, HSP60, HSP70,HSC73, HSP89 αand β in workers exposed to heat, carbon monoxide was also measured by western blot using purified HSPs as antigens. Plasma free amino acids were measured in the saine group of workers. The incidence of antibodies to HSP27 and HSP70 Was significantly higher in the workers working in an environment with extreme heat, and high carbon monoxide ernission than in a control group. The carbon monoxide exposed group showed the highest incidence of antibodies to HSPs. Although our previous results indicated that workers had an insufficient protein intake,plasma free amino acids tended to increase, especially in methionine and tryptophan two kinds of amino acids which are absent from the main stress protein, HSP70.These results suggest that the major problems that these workers may face are how to facilitate the use of plasma free amino acids and reduce the inhibition of synthesis of normal proteins when they are exposed to occupational harmful factors.These resultsalso add new information on the measurement of HSPs as a potential biomonitor to assess whether organisms are experiencing metabolic stress within their environment.展开更多
Using a walnut shellas a carbon source and ZnCl_2 as an activating agent,we resolved the temperature gradient problems of activated carbon in the microwave desorption process.An appropriate amount of silicon carbide w...Using a walnut shellas a carbon source and ZnCl_2 as an activating agent,we resolved the temperature gradient problems of activated carbon in the microwave desorption process.An appropriate amount of silicon carbide was added to prepare the composite activated carbon with high thermalconductivity while developing VOC adsorption-microwave regeneration technology.The experimentalresults show that the coefficient of thermalconductivity of SiC-AC is three times as much as those of AC and SY-6.When microwave power was 480 W in its microwave desorption,the temperature of the bed thermaldesorption was 10 ℃ to 30 ℃ below that of normalactivated carbon prepared in our laboratory.The toluene desorption activation energy was 16.05 k J·mol^(-1),which was 15% less than the desorption activation energy of commercialactivated carbon.This study testified that the process could maintain its high adsorption and regeneration desorption performances.展开更多
To reveal the formation mechanism and main influencing factors of C-segregation in high carbon steel under different solidification rates(40,80,160,200 and 320μm·s^(-1)),the enrichment characteristics of carbon ...To reveal the formation mechanism and main influencing factors of C-segregation in high carbon steel under different solidification rates(40,80,160,200 and 320μm·s^(-1)),the enrichment characteristics of carbon atoms in the solid-liquid zone of Fe-0.61%C steel were studied using a zone melting liquid metal cooling apparatus and electron probe microanalysis.The relationships among micro-segregation of carbon atoms,solid-liquid interface morphology and solidification rate were fully discussed.The results show that large dendrite spacing and a slow-moving dendritic interface create less resistance and more time for the migration of interdendritic carbon atoms to liquid zone.This results in the continuous enrichment of carbon atoms in liquid zone,further expands the solid-liquid temperature range,prolongs the solidification time of molten steel,and causes the formation of carbon micro-segregation at the solidification end as the solidification rate is 40μm·s^(-1).Conversely,abundant and elongated secondary dendrite arms with small spacing seriously impede the diffusion of interdendritic carbon-rich molten steel to liquid zone.As a result,there is only obvious dendrite segregation,but little difference in the carbon content along the solidification direction as solidification rate exceeds 200μm·s^(-1).展开更多
Effect of rare earth metals (REM) on tempering process and decomposition kinetics of martensite and retained austenite of high carbon steel were investigated by DSC technique,based on the non-isothermal kinetic theory...Effect of rare earth metals (REM) on tempering process and decomposition kinetics of martensite and retained austenite of high carbon steel were investigated by DSC technique,based on the non-isothermal kinetic theory.The result shows that the addition of REM in high carbon steel increases the decomposition temperatures of martensite and retained austenite,decreases the thennal effect values,elevates the activity energies and changes the transformation mechanism.展开更多
Rolling process based on the plastic deformation as a surface strengthening treatment was employed,aiming to improve the wear resistance ability and functional performance of the high carbon equivalent gray cast iron(...Rolling process based on the plastic deformation as a surface strengthening treatment was employed,aiming to improve the wear resistance ability and functional performance of the high carbon equivalent gray cast iron(HCEGCI).The microstructures and tribological performance of the untreated and rolled samples were characterized.In addition,the wear mechanism of HCEGCI samples was also studied via pin-on-disc tests.The experimental results show that the as-rolled samples possess the structure-refined layer of 15μm and work-hardened layer of 0.13 mm.In comparison with the surface hardness of untreated samples,the surface hardness of as-rolled samples increases by 84.6%(from 240HV0.1 to 443HV0.1)and the residual compressive stresses existed within the range of 0.2 mm.The wear rates of as-rolled samples were decreased by 38.4%,37.5%,and 44.4%under different loads of 5 N,10 N,and 15 N,respectively.The wear characteristics of the untreated samples mainly exhibit the peeling wear coupled with partial adhesive and abrasive wear.However,as for the as-rolled samples,the adhesive wear was limited by the structure-refined layer and the micro-crack propagation was controlled by the work-hardened layer.Therefore,the wear resistance of as-rolled samples can be improved significantly due to the low wearing degree of the friction contact zone.展开更多
In order to determine the morphology of RE in high carbon steel, it was studied by means of electrolytic extraction and X-ray diffraction analysis. Meanwhile, as a new experimental technique, the gas chromatography an...In order to determine the morphology of RE in high carbon steel, it was studied by means of electrolytic extraction and X-ray diffraction analysis. Meanwhile, as a new experimental technique, the gas chromatography analysis ha;i been used to investigate the necessary condition for the formation of RE-carbide and its chemical property. The results show that the RE-carbide could be formed with which the mischmetal content was about 0. 036 wt% in heavy rail steel, and the ternary compound Fe2Ce2C3 was also identified in which the cerium content exceeded 0.25 wt%. The RE-carbide and Fe2Ce2C3 were both moisture-sensitive.展开更多
For better processing performance of high carbon low alloy steel wire rod,an investigation about the influence of cementite lamellar spacing on wire 'easy drawing' performance is completed.It is pointed out th...For better processing performance of high carbon low alloy steel wire rod,an investigation about the influence of cementite lamellar spacing on wire 'easy drawing' performance is completed.It is pointed out that too thin cementite lamellar spacing(<80 um) reduces the strain hardening level of wire drawing, and reduce the torsion performance of drawn wire at same time.For the wire or wire rod from industrial production,compared with the micro-structure with troostite,the micro-structure with sorbite or sorbite mixed with pearlite is more suitable to the drawing process with high reduction ratio.展开更多
The effect of cooling rate and austenitizing condition on the mechanical properties of high carbon steel (SWRH82B) has beeninvestigated. Specimens were made of high carbon steel rod and heat-treated by Gleeble-2000 to...The effect of cooling rate and austenitizing condition on the mechanical properties of high carbon steel (SWRH82B) has beeninvestigated. Specimens were made of high carbon steel rod and heat-treated by Gleeble-2000 to produce a wide variation in prior austenite size. Different cooling rates were carried out, and then pearlite interlaminar spacing and mechanical properties were measured andtested respectively. According to the results, it could be found that under the continuous cooling with the increase of cooling rate, tensilestrength greatly increases and reduction in area exhibits a slightly increase for an equivalent value of prior austenite grain size. Whenprior austenite size increases, reduction in area decreases, and tensile strength increases slightly for an equivalent value of pearlite interlaminar spacing. It is concluded that prior austenite size primarily controls ductility and pearlite interlaminar spacing controls tensilestrength. Mathematical formulae are given for these relations.展开更多
In order to explore the bonding failure mechanism of high modulus carbon fiber composite materials,the tensile experiment and finite element numerical simulation for single-lap and bevel-lap joints of unidirectional l...In order to explore the bonding failure mechanism of high modulus carbon fiber composite materials,the tensile experiment and finite element numerical simulation for single-lap and bevel-lap joints of unidirectional laminates are carried out,and the stress distributions,the failure modes,and the damage contours are analyzed. The analysis shows that the main reason for the failure of the single-lap joint is that the stress concentration of the ply adjacent to the adhesive layer is serious owing to the modulus difference,and the stress cannot be effectively transmitted along the thickness direction of the laminate. When the tensile stress of the ply exceeds its ultimate strength in the loading process,the surface fiber will fail. Compared with the single-lap joint,the bevel-lap joint optimizes the stress transfer path along the thickness direction,allows each layer of the laminate to share the load,avoids the stress concentration of the surface layer,and improves the bearing capacity of the bevel-lap joint. The improved bearing capacity of the bevellap joint is twice as much as that of the single-lap joint. The research in this paper provides a new idea for the subsequent study of mechanical properties of adhesively bonded composite materials.展开更多
文摘A suitable carburized microstructure with fine granular dispersed carbides in hypereutectoid zone,ultra fine martensite in matrix and recrystallized austenite to be refined to the grain size of 12~14 has been obtained by a new process,which is a high carbon concentration carburizing with rare earth element at low temperature(860~880℃)in a discontinuous gas carburization furnace.There was not much difference for the microstructure in eutectic zone between this and conventional process.Forming mechanism of granular carbides has been also studied in this paper.
基金supported by the Program for New Century Excellent Talents in University from the Ministry of Education of China (No.NCET-04-0285)
文摘An industrial plant trial for optimizing the process parameters in a round billet continuous casting mold with electromagnetic stirring (M-EMS) was performed, in which the influences of stirring parameters with M-EMS on the solidification macrostructure of high carbon steel were investigated. The results show that the billet quality is not well controlled under the condition of working current and frequency with EMS, in which the subsurface crack of grade 1.0-2.0 ups to 38.09%, the central pipe of grade 1.0-1.5 reaches to 14.28%, and the central porosity of grade 1.5 is 14.29%. The parameters of current 260 A and frequency 8 Hz as the final optimum scheme has a remarkable effect for improving the macroscopic quality of billet, in which the subsurface crack, central pipe and skin blowhole are all disappeared, and the central porosity and carbon segregation are also well improved.
文摘The effect of Cr/Mn segregation on the abnormal banded structure of high carbon bearing steel was studied by reheating and hot rolling.With the use of an optical microscope, scanning electron microscope, transmission electron microscope, and electron probe microanalyzer, the segregation characteristics of alloying elements in cast billet and their relationship with hot-rolled plate banded structure were revealed.The formation causes of an abnormal banded structure and the elimination methods were analyzed.Results indicate the serious positive segregation of C, Cr, and Mn alloy elements in the billet.Even distribution of Cr/Mn elements could not be achieved after 10 h of heat preservation at 1200℃, and the spacing of the element aggregation area increased, but the segregation index of alloy elements decreased.Obvious alloying element segregation characteristics are present in the banded structure of the hot-rolled plate.This distinct white band is composed of martensitic phases.The formation of this abnormal pearlite–martensite banded structure is due to the interaction between the undercooled austenite transformation behavior of hot-rolled metal and the segregation of its alloying elements.Under the air cooling after rolling, controlling the segregation index of alloy elements can reduce or eliminate the abnormal banded structure.
文摘The apparent morphologies of packet martensite in eight high carbon steels were researched by using optical microscope, scanning electron microscope, and transmission electron microscope. It was found that the apparent morphologies, substructures, and habit plane of packet martensite in high carbon steels are entirely different from that in low carbon steels; the substructures of packet martensite in high carbon steels possess fully twinned structure, while the substructures of individual coarse martensite plates in these steels bear both fully and partially twinned structures. The formation reason for apparent morphologies, substructures and two habit planes (i. e, { 111 }, and { 225}r) of high carbon martensite were discussed in detail.
文摘Manuscript received 30 July 1999 Abstract The shielded metal arc welding (SMAW) of a manganese steel part as a crossing of railway track to a carbon steel part as the rails of the railroad is the welding of dissimilar steel. It are was known that it is not possible to the the rail of railroad directly to the cross- ing of railway track made from a steel containing about 14% of manganese (wt. ) because of so many differences between the two kinds of steels such as composition, microstructure,mechanical properties and weldability.A method was used to solve the problem by presetting an intermediate layer on each side of the joint and other special procedures were used.The result of test indicated that a good weld joint was obtained.
文摘A certain quantity of RE is dissolved in high-carbon steel. The dissolved RE not only segregates on grain boundary, but also exists in grains. It exists in cementite much more than in ferrite. RE makes the carbides spheroidal and fine, and the carbides distribute uniformly. RE also changes the morphology of pearlite. By means of the analysis of Auger energy spectrum, we find that RE, which is dissolved in cementite, changes the composition and structure of cementite. In the case of higher content of RE and carbon, RE carbide can be formed.
基金supported by the Natural Science Foundation of Southwest University of Science and Technology (No.19zx7163)the National Natural Science Foundation of China (No.51975492)。
文摘The present work employed the X-ray diffraction, scanning electron microscopy, electron backscattered diffraction, and electron probe microanalysis techniques to identify the microstructural evolution and mechanical and abrasive behavior of high carbon steel during quenching-partitioning treatment with an aim to enhance the toughness and wear resistance of high carbon steel.Results showed that, with the increase in partitioning temperature from 250 to 400℃, the amount of retained austenite(RA) decreased resulting from the carbide precipitation effect after longer partitioning times.Moreover, the stability of RA generally increased because of the enhanced degree of carbon enrichment in RA.Given the factors affecting the toughness of high carbon steel, the stability of RA associated with size, carbon content, and morphology plays a significant role in determining the toughness of high carbon steel.The analysis of the wear resistance of samples with different mechanical properties shows that hardness is the primary factor affecting the wear resistance of high carbon steel, and the toughness is the secondary one.
文摘Felt base carbon/carbon composites fabricated by super-high pressure impregnation carbonization process (SPIC) were heat treated at high temperature 2773K. The oxidation properties of felt base carbon/carbon composites were investigated at different temperatures (773-1173K), and the microstructures of carbon/carbon composites were studied by SEM and X-ray diffraction. The experimental results showed that the inter-laminar distance of (002) plane (d002) deceased while the microcrystalline stack height (Lc) increased. The oxidation rate of felt base carbon/carbon composites was invari-able at certain temperatures. The oxidation mechanism of carbon/carbon composites changed remarkably at the oxidation temperature 973K. At the initial oxidation stage of carbon/carbon composites, carbon matrix was oxidized much more rapidly than carbon felt.
文摘Effect of rare earth alloy modification on properties and microstructure of high carbon equivalent gray cast iron was investigated.The experimental results show that in the way of mechanical property,when the addition of rare earth alloy is 0.2% and 0.3%,the tensile strength of cast iron increases.In the way of microstructure,the addition of rare earth alloy increases the number of primary austenite dendrites,reduces secondary dendritic arm spacing,and changes the eutectic size and quantity.When rare earth alloy is added into gray cast iron,the morphology and quantity of graphite play a major role on the improvement of tensile strength.
文摘Antibodies to the ubiquitous group of stress proteins known as heat shock proteins (Hsps) have been found to be associated with a number of diseases in humans. Hsps are known to be induced by certain xenobiotics, some of which are common in the working environment. The biological significance of the presence of such autoantibodies is presently unclear. In the present study, we used immunoblotting to investigate the presence of antibodies against the different stress proteins, Hsp27, Hsp60, Hsp71, Hse (heat shock cognate ) 73 and Hsp89a and D in groups of workers exposed to high temperature or carbon monoxide. These data were related to a detailed clinical evaluation and to various laboratory measurements including electrocardiogram (ECG), B echogram, white blood cell counts and typing, the activity of alanine aminotransferase (ALT), acid phosphatase (ACP) and alkaline phosphatase (ALP) and lymphocyte DNA damage. Antibodies to Hsp27 and Hsp71 were found more frequently in the high temperature and carbon monoxide-exposed groups than in controls (P (0.05 ). The carbon monoxide-exposed group showed the highest incidence of anti-Hsp antibodies. Anti-Hsp60 antibodies were only detected in workers exposed to high temperature or carbon monoxide. The percentage of workers with abnormal ECG, B echogram changes and displaying hepatitis B antigen (HBsAg ) was higher in the carbon monoxide group than in the control group (P<0.05 ).There was a significant inerease in the activity of ALT in the high temperature and carbon monoxide groups and in the activities of ACP and ALP in the carbon monoxide group (P<0.05 ). The extent of DNA damage measured in lymphoeytes was higher in workers from the high temperature and carbon monoxide-cxposed groups. We suggest that the increased frequeney of antibodies to Hsps is the result of these damages, of the release of denatured Hsps and of a decrease in the phagocytic ability of macrophages in these workers. The data gathered in the present study show a statistical relation between the occurrence of antibodies against Hsps and the frequency of health problems in workers and suggest a potential role for the antibodies as useful biomarkers to assess whether workers are experieneing environmental stress
基金This work was financially supported by the National Natural Science Foundation of China and Baosteel (No.50174003).
文摘The semi-solid high carbon steel T12 was rolled in a closed box groove under a certain condition by the rheo-rolling equipment, and the microstructural morphology of the semi-solid T12 before and after deformation was investigated by optical mi- croscope to analyze and summarize the microstructure evolution law of T12 deformed in semi-solid state. The experiment results show that the grain shape before deformation of the semi-solid T12 steel displays globule or ellipse by the electromagnetic stirring, the distribution of solid and liquid phases is homogeneous. But the microstructure of semi-solid product after rheo-rolling exhibits macrosegregation that the distribution of liquid and solid phases changes, the liquid phases divorce from the solid phases. In the transverse section, most of the solid phases get together in the center of the specimen, the liquid phases flow to the surface or the edge of the specimen, and the grains occur plastic deformation while reduction increased. In longitudinal section, the middle micro- structure of the specimen is more homogeneous than that at the head or tail, the head microstructure is similar to the tail and the size of the grains is not homogeneous.
文摘In this study,we have examined the effects of exposure to high temperature, carbon inonoxideor a combination of both conditions in a model system,the rat and in industrial workers.In the rat liver, HSP70 mRNA and HSP70 synthesis were measured by dot hybridization and western blot. The results showed that after a heat stress HSP70 mRNA and its product, HSP70 increased significantly and there was a synergism in the combined effects of high temperature and carbon monoxide exposure on the induction of HSP70 mRNA and HSP70 synthesis. Heat played a major role in this induction. The presence of antibodies to human HSP27, HSP60, HSP70,HSC73, HSP89 αand β in workers exposed to heat, carbon monoxide was also measured by western blot using purified HSPs as antigens. Plasma free amino acids were measured in the saine group of workers. The incidence of antibodies to HSP27 and HSP70 Was significantly higher in the workers working in an environment with extreme heat, and high carbon monoxide ernission than in a control group. The carbon monoxide exposed group showed the highest incidence of antibodies to HSPs. Although our previous results indicated that workers had an insufficient protein intake,plasma free amino acids tended to increase, especially in methionine and tryptophan two kinds of amino acids which are absent from the main stress protein, HSP70.These results suggest that the major problems that these workers may face are how to facilitate the use of plasma free amino acids and reduce the inhibition of synthesis of normal proteins when they are exposed to occupational harmful factors.These resultsalso add new information on the measurement of HSPs as a potential biomonitor to assess whether organisms are experiencing metabolic stress within their environment.
基金Funded by the National High Technology Research and Development Program of China("863"Program)(No.2006AA06A310)
文摘Using a walnut shellas a carbon source and ZnCl_2 as an activating agent,we resolved the temperature gradient problems of activated carbon in the microwave desorption process.An appropriate amount of silicon carbide was added to prepare the composite activated carbon with high thermalconductivity while developing VOC adsorption-microwave regeneration technology.The experimentalresults show that the coefficient of thermalconductivity of SiC-AC is three times as much as those of AC and SY-6.When microwave power was 480 W in its microwave desorption,the temperature of the bed thermaldesorption was 10 ℃ to 30 ℃ below that of normalactivated carbon prepared in our laboratory.The toluene desorption activation energy was 16.05 k J·mol^(-1),which was 15% less than the desorption activation energy of commercialactivated carbon.This study testified that the process could maintain its high adsorption and regeneration desorption performances.
基金support from the State Key Laboratory of Refractories and Metallurgy(Wuhan University of Science and Technology)(Grant No.G201902)the National Natural Science Foundation of China(Grant Nos.51874001,U1760108)。
文摘To reveal the formation mechanism and main influencing factors of C-segregation in high carbon steel under different solidification rates(40,80,160,200 and 320μm·s^(-1)),the enrichment characteristics of carbon atoms in the solid-liquid zone of Fe-0.61%C steel were studied using a zone melting liquid metal cooling apparatus and electron probe microanalysis.The relationships among micro-segregation of carbon atoms,solid-liquid interface morphology and solidification rate were fully discussed.The results show that large dendrite spacing and a slow-moving dendritic interface create less resistance and more time for the migration of interdendritic carbon atoms to liquid zone.This results in the continuous enrichment of carbon atoms in liquid zone,further expands the solid-liquid temperature range,prolongs the solidification time of molten steel,and causes the formation of carbon micro-segregation at the solidification end as the solidification rate is 40μm·s^(-1).Conversely,abundant and elongated secondary dendrite arms with small spacing seriously impede the diffusion of interdendritic carbon-rich molten steel to liquid zone.As a result,there is only obvious dendrite segregation,but little difference in the carbon content along the solidification direction as solidification rate exceeds 200μm·s^(-1).
文摘Effect of rare earth metals (REM) on tempering process and decomposition kinetics of martensite and retained austenite of high carbon steel were investigated by DSC technique,based on the non-isothermal kinetic theory.The result shows that the addition of REM in high carbon steel increases the decomposition temperatures of martensite and retained austenite,decreases the thennal effect values,elevates the activity energies and changes the transformation mechanism.
基金Funded by the National Natural Science Foundation of China(No.51872254)the Yangzhou Hanjiang District Science and Technology Plan Project of China(No.HJM2019006)。
文摘Rolling process based on the plastic deformation as a surface strengthening treatment was employed,aiming to improve the wear resistance ability and functional performance of the high carbon equivalent gray cast iron(HCEGCI).The microstructures and tribological performance of the untreated and rolled samples were characterized.In addition,the wear mechanism of HCEGCI samples was also studied via pin-on-disc tests.The experimental results show that the as-rolled samples possess the structure-refined layer of 15μm and work-hardened layer of 0.13 mm.In comparison with the surface hardness of untreated samples,the surface hardness of as-rolled samples increases by 84.6%(from 240HV0.1 to 443HV0.1)and the residual compressive stresses existed within the range of 0.2 mm.The wear rates of as-rolled samples were decreased by 38.4%,37.5%,and 44.4%under different loads of 5 N,10 N,and 15 N,respectively.The wear characteristics of the untreated samples mainly exhibit the peeling wear coupled with partial adhesive and abrasive wear.However,as for the as-rolled samples,the adhesive wear was limited by the structure-refined layer and the micro-crack propagation was controlled by the work-hardened layer.Therefore,the wear resistance of as-rolled samples can be improved significantly due to the low wearing degree of the friction contact zone.
文摘In order to determine the morphology of RE in high carbon steel, it was studied by means of electrolytic extraction and X-ray diffraction analysis. Meanwhile, as a new experimental technique, the gas chromatography analysis ha;i been used to investigate the necessary condition for the formation of RE-carbide and its chemical property. The results show that the RE-carbide could be formed with which the mischmetal content was about 0. 036 wt% in heavy rail steel, and the ternary compound Fe2Ce2C3 was also identified in which the cerium content exceeded 0.25 wt%. The RE-carbide and Fe2Ce2C3 were both moisture-sensitive.
文摘For better processing performance of high carbon low alloy steel wire rod,an investigation about the influence of cementite lamellar spacing on wire 'easy drawing' performance is completed.It is pointed out that too thin cementite lamellar spacing(<80 um) reduces the strain hardening level of wire drawing, and reduce the torsion performance of drawn wire at same time.For the wire or wire rod from industrial production,compared with the micro-structure with troostite,the micro-structure with sorbite or sorbite mixed with pearlite is more suitable to the drawing process with high reduction ratio.
文摘The effect of cooling rate and austenitizing condition on the mechanical properties of high carbon steel (SWRH82B) has beeninvestigated. Specimens were made of high carbon steel rod and heat-treated by Gleeble-2000 to produce a wide variation in prior austenite size. Different cooling rates were carried out, and then pearlite interlaminar spacing and mechanical properties were measured andtested respectively. According to the results, it could be found that under the continuous cooling with the increase of cooling rate, tensilestrength greatly increases and reduction in area exhibits a slightly increase for an equivalent value of prior austenite grain size. Whenprior austenite size increases, reduction in area decreases, and tensile strength increases slightly for an equivalent value of pearlite interlaminar spacing. It is concluded that prior austenite size primarily controls ductility and pearlite interlaminar spacing controls tensilestrength. Mathematical formulae are given for these relations.
文摘In order to explore the bonding failure mechanism of high modulus carbon fiber composite materials,the tensile experiment and finite element numerical simulation for single-lap and bevel-lap joints of unidirectional laminates are carried out,and the stress distributions,the failure modes,and the damage contours are analyzed. The analysis shows that the main reason for the failure of the single-lap joint is that the stress concentration of the ply adjacent to the adhesive layer is serious owing to the modulus difference,and the stress cannot be effectively transmitted along the thickness direction of the laminate. When the tensile stress of the ply exceeds its ultimate strength in the loading process,the surface fiber will fail. Compared with the single-lap joint,the bevel-lap joint optimizes the stress transfer path along the thickness direction,allows each layer of the laminate to share the load,avoids the stress concentration of the surface layer,and improves the bearing capacity of the bevel-lap joint. The improved bearing capacity of the bevellap joint is twice as much as that of the single-lap joint. The research in this paper provides a new idea for the subsequent study of mechanical properties of adhesively bonded composite materials.