A high dynamics algorithm based on steepest ascent method for GNSS receiver

High dynamic conditions impose critical challenges on Global Navigation Satellite System(GNSS)receivers,leading to large tracking errors or even loss of tracking.Current methods that intend to improve receivers’adaptability for high dynamics require either complicated structures or prior statistical information of noises.This paper proposes a high dynamics algorithm based on steepest ascent method that can circumvent the deficiencies of existing methods.First,the relationship between the error of carrier tracking and the maximum of Fast Fourier Transform(FFT)outputs is established,and a performance function based on the steepest ascent method is designed.It can keep stable in high dynamics.Second,a new carrier-tracking loop is constructed by deploying the performance function.When the variation of GPS receiver acceleration ranges from 10 g to 100 g,compared with the PLL that either loses lock or keeps tracking accuracy less than 33.89 Hz,the experimental results show that the proposed method can not only keep tracking,but also achieve tracking accuracy more than 2.77 Hz.

Optimization of the carrier tracking loop for GPS high dynamic receivers

A carrier tracking loop which can adjust the loop parameters adaptively is proposed for high dynamic application. Three modules, called the α-β-γT filter model, adaptive loop structure mod- el and adaptive loop bandwidth model respectively, are added in the presented tracking loop com- pared with the traditional carrier tracking loop based on the second-order frequency lock loop （FLL） assisting third-order phase lock loop （PLL） loop filter. And the optimization methods for the track- ing bandwidth and the carrier loop order are analyzed. The real-time estimation methods of the dy- namic parameters, the velocity, acceleration and jerk along the line of sight （LOS） between the sat- ellite and the receiver＇ s antenna, and the measurement parameters are discussed based on the pres- ented α-β-γ filter algorithm. A method is introduced to improve the filter＇ s dynamic response to meet high dynamic application by self-adjusted α-β-γ filter coefficient used in the tracking loop. The performance of three cases with different carrier tracking loop is compared by simulation.

A Model of Dynamic Recrystallization in Alloys during High Strain Plastic Deformation

Recrystallized grains, less than 200 nm in diameter were observed in heavily shear zones of a high strength low alloy steel and a Ni-based alloy, and Also grain refinement, less than 3 μm in diameter was made in high purity aluminum by ECAE at ambient temperature. The experimental results showed that high strain rate and large deformation could induce dynamic recrystallization.Based on dislocation dynamics and grain orientation change enhanced by plastic deformation,a model for the recrystallization process is developed. The model is used to explain the ultra fine grains which are formed at a temperature still much lower than that for the conventional recrystallization

Unsteady aerodynamics modeling for flight dynamics application

In view of engineering application, it is practicable to decompose the aerodynamics into three components： the static aerodynamics, the aerodynamic increment due to steady rotations, and the aerodynamic increment due to unsteady separated and vortical flow. The first and the second components can be presented in conventional forms, while the third is described using a one-order differential equation and a radial-basis-function （RBF） network. For an aircraft configuration, the mathematical models of 6- component aerodynamic coefficients are set up from the wind tunnel test data of pitch, yaw, roll, and coupled yawroll large-amplitude oscillations. The flight dynamics of an aircraft is studied by the bifurcation analysis technique in the case of quasi-steady aerodynamics and unsteady aerodynam- ics, respectively. The results show that： （1） unsteady aerodynamics has no effect upon the existence of trim points, but affects their stability; （2） unsteady aerodynamics has great effects upon the existence, stability, and amplitudes of periodic solutions; and （3） unsteady aerodynamics changes the stable regions of trim points obviously. Furthermore, the dynamic responses of the aircraft to elevator deflections are inspected. It is shown that the unsteady aerodynamics is beneficial to dynamic stability for the present aircraft. Finally, the effects of unsteady aerodynamics on the post-stall maneuverability

Parametrical analysis of the railways dynamic response at high speed moving loads

The paper introduces some findings about a sensitivity analysis conducted on every geometrical and mechanical parameters which characterize the use of a railway superstructure at the high velocity. This analysis was carried out by implementing a forecast model that is derived from the simplified Gazetas and Dobry one. This model turns out to be particularly appropriate in the explication of problems connected to high velocity, since it evaluates both inertial and viscous effects activated by the moving load speed. The model implementation requires the transfer function determination that represents the action occurred by the bed surfaces on the railway and it therefore contains information concerning the geometrical and the mechanical characteristics of the embankment, of the ballast and of the sub-ballast. The transfer function H has been evaluated with the finite elements method and particularly, by resorting the ANSYS code with a harmonic structural analysis in the frequencies field. The authors, from the critic examination of the system＇s dynamics response in its entirety, glean a series of observations both of a general and a specific character, finally attaining a propose of a design modification of the standard railway superstructure at the high velocity of train operation adopted today especially in Italy.

Combined grain size, strain rate and loading condition effects on mechanical behavior of nanocrystalline Cu under high strain rates

Molecular dynamics simulations of nanocrystalline Cu with average grain sizes of 3.1 nm, 6.2 nm, 12.4 nm and 18.6 nm under uniaxial strain and stress tension at strain rates of 10^8 s^-1, 10^9 S^-1 and 10^10 s^-1 are performed to study the combined grain size, strain rate and loading condition effects on mechanical properties. It is found that the strength of nanocrystalline Cu increases as grain size increases regardless of loading condition. Both the strength and ductility of nanocrystalline Cu increase with strain rate except that there is no monotonic relation between the strength and strain rate for specimens under uni- axial strain loading. Moreover, the strength and ductility of specimens under uniaxial strain loading are lower than those under uniaxial stress loading. The nucleation of voids at grain boundaries and their subsequent growth characterize the failure of specimens under uniaxial strain loading, while grain boundary sliding and necking dominate the failure of specimens under uniaxial stress loading. The rate dependent strength is mainly caused by the dynamic wave effect that limits dislocation motion, while combined twinning and slipping mechanism makes the material more ductile at higher strain rates.

Digital implementation and analysis of a high dynamic frequency tracking loop

In the wireless guidance system, the signals that receiver received has obvious Doppler shift for the high dynamic characteristic of the carrier. A new solution of carrier frequency tracking loop with frequency modifying system is put forward. The characteristic of cross product auto frequency control and the second order loop filter in this loop are analyzed. The simulation shows that this loop can accomplish frequency tracking well in high dynamic circumstance.

High dynamic synchronization algorithm based on cyclic spectral density

A new high dynamic synchronization algorithm using cyclic spectral density was presented according to the theories of cyclic spectral density and its anti-interface and anti-noise properties.The closed forms of frequency error and phase error were obtained,and their performances were analyzed.The in-phase signal throw costas loop was normalized to obtain a cosine signal.Cyclic spectral density of the cosine signal of was computed to obtain the frequency error and the phase error and then results were put into NCO to synchronize.Finally,the performance of the presented algorithms was compared with the conventional algorithms by virtue of simulations,and the simulation results proved the correctness and the superiority of the new algorithms.

Principle and key technology of generalized high precision simulation of TT&C channel

A generalized simulation method of the tracking,telemetry and control（TT＆C） channel,which is applicable to wideband and arbitrary radio frequency（RF） signal,is proposed.It can accurately simulate the dynamic transmission delay of the arbitrary RF signal in channels,especially regardless of any prior knowledge including signal form,signal parameters,and so on.The proposed method orthogonally demodulates the wideband and arbitrary RF signal to complex baseband by a known local oscillator（LO） signal.Whereafter,it takes measures to obtain the delay reconstruction signal of baseband signals based on the dynamic transmission delay between a ground station and a responder.Meanwhile,it manages to obtain the delay reconstruction signal of LO signals.The simulation output signal（the delayed RF signal） can be achieved through the synthesis of the two delay reconstruction signals mentioned above.The principle and its related key technology are described in detail,and the realizable system architecture is given.

Multi-exposure fusion for high dynamic range scene

Due to the existing limited dynamic range a camera cannot reveal all the details in a high-dynamic range scene. In order to solve this problem,this paper presents a multi-exposure fusion method for getting high quality images in high dynamic range scene. First,a set of multi-exposure images is obtained by multiple exposures in a same scene and their brightness condition is analyzed. Then,multi-exposure images under the same scene are decomposed using dual-tree complex wavelet transform( DT-CWT),and their low and high frequency components are obtained. Weight maps according to the brightness condition are assigned to the low components for fusion. Maximizing the region Sum Modified-Laplacian( SML) is adopted for high-frequency components fusing. Finally,the fused image is acquired by subjecting the low and high frequency coefficients to inverse DT-CWT.Experimental results show that the proposed approach generates high quality results with uniform distributed brightness and rich details. The proposed method is efficient and robust in varies scenes.

A real-time algorithm for broadband highdynamic seismic data compression

A new real-time algorithm of data compression, including the segment-normalized logical compression and socalled 'one taken from two samples',is presented for broadband high dynamic seismic recordings. This algorithm was tested by numerical simulation and data observed. Its results demonstrate that total errors in recovery data are less than 1% of original data in time domain,0.5% in frequency domain, when using these two methods together.Its compression ratio is greater than 3.The data compression softwares based on the algorithm have been used in the GDS-1000 portable broadband digital seismograph.

Experimental study on the time-dependent dynamic mechanical behaviour of C60 concrete under high-temperatures

To study the dynamic mechanical behavior of C 60 concrete at high temperatures,impact tests under different steady-state temperature fields（ 100,200,300,400 and 500 ℃） were conducted under a variety of durations at the corresponding constant high temperature,namely 0,30,60,90 and 120 min,employing split H opkinson pressure bar（ SH PB） system. In addition,the impact tests were also conducted on the specimens cooled fromthe high temperature to the roomtemperature and the specimen under roomtemperature. Fromthe analysis,it is found that C 60 concrete has a time-dependent behavior under hightemperature environment. U nder 100,200,300,400 and 500 ℃ steady-state temperature fields respectively,as the duration at the corresponding constant high temperature increases,the dynamic compressive strength and the elastic modulus decrease but the peak strain generally ascends. After cooling to the roomtemperature,the dynamic compressive strength and the elastic modulus descend as well,but the peak strain increases first and then decreases slightly,when the duration increases. For specimens under and cooled fromthe high-temperature,as the temperature increases,the dynamic compressive strength and the peak strain raise first and then reduce gradually,and the dynamic compressive strength of specimen under high temperature is higher than that of the specimen cooled fromthe same high temperature.

Distortion-Free Data Embedding Scheme for High Dynamic Range Images

Distortion-free data embedding is a technique which can assure that not only the secret data is correctly extracted but also the cover media is recovered without any distortion after secret data is extracted completely. Because of these advantages, this technique attracts the attention of many researchers. In this paper, a new distortion-free data embedding scheme for high dynamic range （HDR） images is proposed. By depending on Cartesian product, this scheme can obtain higher embedding capacity while maintaining the exactly identical cover image and stego image when using the tone mapping algorithms. In experimental results, the proposed scheme is superior to Yu et aL＇s scheme in regard to the embedding rate——an average embedding rate of 0.1355 bpp compared with Yn et aL＇s scheme （0.1270 bpp）.

Thermal Activation Analyses of Dynamic FractureToughness of High Strength Low Alloy Steels

A formula is derived for determining the influence of temperature and loading rate on dynamic fracture toughness of a high strength low alloy steel (HQ785C) from thermal activation analysis of the experimental results of three-point bend specimens as well as introducing an Arrhenius formula. It is shown that the results obtained by the given formula are in good agreement with the experimental ones in the thermal activation region. The present method is also valuable to describe the relationship between dynamic fracture toughness and temperature and loading rate of other high strength low alloy steels.

THE APPLICATION OF COMPATIBLE STRESS ITERATIVE METHOD IN DYNAMIC FINITE ELEMENT ANALYSIS OF HIGH VELOCITY IMPACT

There is a common difficulty in elastic-plastic impact codes such as EPIC[2,3] NONSAP[4], etc.. Most of these codes use the simple linear functions usually taken from static problem to represent the displacement components. In such finite element formulation, the stress components are constant in each element and they are discontinuous in any two neighboring elements. Therefore, the bases of using the virtual work principle in such elements are unreliable. In this paper, we introduce a new method, namely, the compatible stress iterative method, to eliminate the above-said difficulty. The calculated examples show that the calculation using the new method in dynamic finite element analysis of high velocity impact is valid and stable, and the element stiffness can be somewhat reduced.

Hawk‐eye‐inspired perception algorithm of stereo vision for obtaining orchard 3D point cloud navigation map

The binocular stereo vision is the lowest cost sensor for obtaining 3D information.Considering the weakness of long‐distance measurement and stability,the improvement of accuracy and stability of stereo vision is urgently required for application of precision agriculture.To address the challenges of stereo vision long‐distance measurement and stable perception without hardware upgrade,inspired by hawk eyes,higher resolution perception and the adaptive HDR(High Dynamic Range)were introduced in this paper.Simulating the function from physiological structure of‘deep fovea’and‘shallow fovea’of hawk eye,the higher resolution reconstruction method in this paper was aimed at ac-curacy improving.Inspired by adjustment of pupils,the adaptive HDR method was proposed for high dynamic range optimisation and stable perception.In various light conditions,compared with default stereo vision,the accuracy of proposed algorithm was improved by 28.0%evaluated by error ratio,and the stability was improved by 26.56%by disparity accuracy.For fixed distance measurement,the maximum improvement was 78.6%by standard deviation.Based on the hawk‐eye‐inspired perception algorithm,the point cloud of orchard was improved both in quality and quantity.The hawk‐eye‐inspired perception algorithm contributed great advance in binocular 3D point cloud recon-struction in orchard navigation map.

High Dynamic Bounding and Jumping Motion of Quadruped Robot Based on Stable Optimization Control

Aiming at the environment such as ravines and obstacles that may be encountered in the actual movement,this paper proposes a method for optimizing the bounding and jumping motion based on the ground touching force trajectory and the air motion trajectory of the quadruped robot.The method of optimizing the ground reaction force according to the speed of the demand and the height of the jump,and adjusting the stance and swing time according to the relationship of dynamics and momentum conservation.At the same time,under the constraints of dynamics and energy consumption of the robot system,considering the jumping distance and height,a method for optimizing the air trajectory of bounding and jumping is proposed.State switching and landing stability control are also added.Finally,the experimental results show that the quadruped robot has strong bounding and jumping ability,and has achieved stable bounding movement and forward jump movement of 0.8 m.

Deep Learning-Based Symbol Detection for Time-Varying Nonstationary Channels

The highly dynamic channel(HDC)in an extremely dynamic environment mainly has fast timevarying nonstationary characteristics.In this article,we focus on the most difficult HDC case,where the channel coherence time is less than the symbol period.To this end,we propose a symbol detector based on a long short-term memory(LSTM)neural network.Taking the sampling sequence of each received symbol as the LSTM unit's input data has the advantage of making full use of received information to obtain better performance.In addition,using the basic expansion model(BEM)as the preprocessing unit significantly reduces the number of neural network parameters.Finally,the simulation part uses the highly dynamic plasma sheath channel(HDPSC)data measured from shock tube experiments.The results show that the proposed BEM-LSTM-based detector has better performance and does not require channel estimation or channel model information.

Performance analysis of fast GPS signal acquisition based on PMF and Window FFT

Combining the advantages of partial matched filter（PMF） and fast Fourier transform（FFT）,an improved fast acquisition method for GPS C/A code is proposed.According to PMF-FFT acquisition architecture,the greater the number of PMF will bring out the more slowly amplitude decreasing of the amplitude-frequency response,the smaller scale of the corresponding PMF,and the larger computation of the FFT.In order to compensate the frequency spectrum attenuation caused by spectrum leakage and fence effect,adding window function to PMF-FFT is presented.Through comparing the influences to the acquisition performance based on rectangular,Hamming,Blackman and Rife-Vincent（Ⅲ） window functions,an improved Rife-Vincent Ⅲ windowing algorithm is recommended for the fast acquisition based on PMF-FFT.

Adaptability Analysis of IP Routing Protocol in Broadband LEO Constellation Systems

With the inclusion of satellite Internet as the information infrastructure in China's "new infrastructure" category,relevant domestic industries and scientific research institutes have successively carried out the design of broadband low earth orbit(LEO) constellation systems and key technical research.As the core technology for the satellite-to-ground network communications of a broadband LEO constellation system,routing technology is extremely important for the efficient and reliable transmission of various service data.Focusing on the two important broadband LEO constellation systems in China,in-depth analysis and simulation of the high dynamics of the satellite-to-ground satellites are conducted in this paper to obtain more accurate network topology changes and characteristics;then the adaptability of the ground standard IP routing protocol to the broadband LEO constellation system is analyzed,and an LEO constellation simulation scenario is built with the Opnet software.The simulation results of the convergence performance of the standard IP routing protocol are produced.The results show that the IP protocol does not perform well for LEO satellite constellation networks.Based on the studies,some solutions are proposed to take full advantages of the characteristics of LEO satellite systems.These can also provide a reference for the choice of intersatellite routing architecture and protocol technology for broadband LEO constellation in the future development.