Disturbances rejection optimization based on improved two-degree-of-freedom LADRC for permanent magnet synchronous motor systems

Permanent magnet synchronous motor(PMSM)speed control systems with conventional linear active disturbance rejection control(CLADRC)strategy encounter issues regarding the coupling between dynamic response and disturbance suppression and have poor performance in suppressing complex nonlinear disturbances.In order to address these issues,this paper proposes an improved two-degree-of-freedom LADRC(TDOF-LADRC)strategy,which can enhance the disturbance rejection performance of the system while decoupling entirely the system's dynamic and anti-disturbance performance to boost the system robustness and simplify controller parameter tuning.PMSM models that consider total disturbances are developed to design the TDOF-LADRC speed controller accurately.Moreover,to evaluate the control performance of the TDOF-LADRC strategy,its stability is proven,and the influence of each controller parameter on the system control performance is analyzed.Based on it,a comparison is made between the disturbance observation ability and anti-disturbance performance of TDOF-LADRC and CLADRC to prove the superiority of TDOF-LADRC in rejecting disturbances.Finally,experiments are performed on a 750 W PMSM experimental platform,and the results demonstrate that the proposed TDOF-LADRC exhibits the properties of two degrees of freedom and improves the disturbance rejection performance of the PMSM system.

Adaptive Gain Tuning Rule for Nonlinear Sliding-mode Speed Control of Encoderless Three-phase Permanent Magnet Assisted Synchronous Motor

In this paper, an adaptive gain tuning rule is designed for the nonlinear sliding mode speed control(NSMSC) in order to enhance the dynamic performance and the robustness of the permanent magnet assisted synchronous reluctance motor(PMa-Syn RM) with considering the parameter uncertainties. A nonlinear sliding surface whose parameters are altering with time is designed at first. The proposed NSMSC can minimize the settling time without any overshoot via utilizing a low damping ratio at starting along with a high damping ratio as the output approaches the target set-point. In addition, it eliminates the problem of the singularity with the upper bound of an uncertain term that is hard to be measured practically as well as ensures a rapid convergence in finite time, through employing a simple adaptation law. Moreover, for enhancing the system efficiency throughout the constant torque region, the control system utilizes the maximum torque per ampere technique. The nonlinear sliding surface stability is assured via employing Lyapunov stability theory. Furthermore, a simple sliding mode estimator is employed for estimating the system uncertainties. The stability analysis and the experimental results indicate the effectiveness along with feasibility of the proposed speed estimation and the NSMSC approach for a 1.1-k W PMa-Syn RM under different speed references, electrical and mechanical parameters disparities, and load disturbance conditions.

Speed Regulation Method Using Genetic Algorithm for Dual Three-phase Permanent Magnet Synchronous Motors

Dual three-phase Permanent Magnet Synchronous Motor(DTP-PMSM)is a nonlinear,strongly coupled,high-order multivariable system.In today’s application scenarios,it is difficult for traditional PI controllers to meet the requirements of fast response,high accuracy and good robustness.In order to improve the performance of DTP-PMSM speed regulation system,a control strategy of PI controller based on genetic algorithm is proposed.Firstly,the basic mathematical model of DTP-PMSM is established,and the PI parameters of DTP-PMSM speed regulation system are optimized by genetic algorithm,and the modeling and simulation experiments of DTP-PMSM control system are carried out by MATLAB/SIMULINK.The simulation results show that,compared with the traditional PI control,the proposed algorithm significantly improves the performance of the control system,and the speed output overshoot of the GA-PI speed control system is smaller.The anti-interference ability is stronger,and the torque and double three-phase current output fluctuations are smaller.

Rotor Strength Analysis of High-speed Permanent Magnet Synchronous Motors

为了对转子进行有效的冷却，在满足电机电磁性能的前提下，可通过减小保护套的厚度来尽可能增大定转子之间的气隙，因而必须对保护套和永磁体进行强度校核。将转子受力状况简化为平面应变问题，在此基础上推导出了两层过盈配合、三层过盈配合转子的应力场、应变场、位移场的解析公式，并利用有限元方法验证了解析公式的正确性。归纳了高速情况下热套式永磁转子强度设计准则，为转子的优化设计提供了理论依据。以一台额定转速120kr／min、10kW的高速永磁同步电机为例，给出了两种常用过盈配合高速电机转子的强度设计方法。

Analysis for Rotor Losses of High Speed Permanent Magnet Synchronous Motor

This paper presents an analysis based on analytical method for solid rotor motors for determining the rotor eddy current losses due to the current harmonics of the stator winding. The accuracy of the analytical results is verified by experiments.

Speed sensorless FCS-MPTC based on FOSM-MRAS five-phase permanent magnet synchronous motor

For the two-level five-phase permanent magnet synchronous motor(FP-PMSM)drive system,an improved finite-control-set model predictive torque control(MPTC)strategy is adopted to reduce torque ripple and improve the control performance of the system.The mathematical model of model reference adaptive system(MRAS)of FP-PMSM is derived and a method based on fractional order sliding mode(FOSM)is proposed to construct the model reference adaptive system(FOSMMRAS)to improve the motor speed estimation accuracy and eliminate the sliding mode integral saturation effect.The simulation results show that the FP-PMSM speed sensorless FCS-MPTC system based on FOSM-MRAS has strong robustness,good dynamic performance and static performance,and high reliability.

Investigation of Optimal Split Ratio of 6-Slot/2-pole High Speed Permanent Magnet Motor with Toroidal Winding

Split ratio,i.e.the ratio of stator inner diameter to outer diameter,has a closed relationship with electromagnetic performance of permanent magnet(PM)motors.In this paper,the toroidal windings with short end-winding axial length are employed in the 6-slot/2-pole(6s/2p)PM motor for high speed applications.The split ratio is optimized together with the ratio of inner slot to outer slot area,i.e.slot ratio,considering stator total loss(stator iron loss and copper loss).In addition,the influence of maximum stator iron flux density and tooth-tip on the optimal split ratio,slot ratio,and average torque is investigated.The analytical predictions show that when the slot ratio is 0.5,the maximum torque can be achieved,and the optimal split ratio increases with the decrease of slot ratio,as confirmed by the finite element(FE)analyses.Finally,some of predicted results are verified by the measured results of 6s/2p prototype motor with 0.5 slot ratio.

Laboratory Implementation of Direct Torque Controller based Speed Loop Pseudo Derivative Feedforward Controller for PMSM Drive

This paper,evaluate the effectiveness of a proposed speed loop pseudo derivative feedforward(PDFF)controller-based direct torque controller(DTC)for a PMSM drive against the performance of existing PI speed controller-based DTC and hysteresis current controller(HCC).The proposed PDFF-based speed regulator effectively reduces oscillation and overshoot associated with rotor angular speed,electromagnetic torque,and stator current.Two case studies,one using forward-to-reverse motoring operation and the other involving reverse-to-forward braking operation,has been validated to show the effectiveness of the proposed control strategy.The proposed controller's superior performance is demonstrated through experimental verification utilizing an FPGA controller for a 1.5 kW PMSM drive laboratory prototype.

Comparison of Two Novel MRAS Based Strategies for Identifying Parameters in Permanent Magnet Synchronous Motors

Two model reference adaptive system （MRAS） estimators are developed for identifying the parameters of permanent magnet synchronous motors （PMSM） based on the Lyapunov stability theorem and the Popov stability criterion, respectively. The proposed estimators only need online measurement of currents, voltages, and rotor speed to effectively estimate stator resistance, inductance, and rotor flux-linkage simultaneously. The performance of the estimators is compared and verified through simulations and experiments, which show that the two estimators are simple, have good robustness against parameter variation, and are accurate in parameter tracking. However, the estimator based on the Popov stability criterion, which can overcome parameter variation in a practical system, is superior in terms of response speed and convergence speed since there are both proportional and integral units in the estimator, in contrast to only one integral unit in the estimator based on the Lyapunov stability theorem. In addition, the estimator based on the Popov stability criterion does not need the expertise that is required in designing a Lyapunov function.

Finite-Control-Set Model Predictive Control of Permanent Magnet Synchronous Motor Drive Systems——An Overview

Permanent magnet synchronous motors(PMSMs)have been widely employed in the industry. Finite-control-set model predictive control(FCS-MPC), as an advanced control scheme, has been developed and applied to improve the performance and efficiency of the holistic PMSM drive systems. Based on the three elements of model predictive control, this paper provides an overview of the superiority of the FCS-MPC control scheme and its shortcomings in current applications. The problems of parameter mismatch, computational burden, and unfixed switching frequency are summarized. Moreover, other performance improvement schemes, such as the multi-vector application strategy, delay compensation scheme, and weight factor adjustment, are reviewed. Finally, future trends in this field is discussed, and several promising research topics are highlighted.

Vector control of permanent magnet synchronous motor based on dynamic matrix control

Aiming at the control problem of strongly nonlinear and coupled permanent magnet synchronous motor(PMSM)oil rig,this paper presents a predictive control method based on dynamic matrix model.In this method,the dynamic matrix algorithm using multistep prediction technique is applied to the speed loop control of the motor vector control.And its control effect is compared with the traditional proportional integral(PI)control of the motor.By comparing the initial dynamic response and the steady-state recovery under load interference of the two methods,it is shown that the dynamic response and the robustness of the motor controlled by the new method is better than that controlled by conventional PI method.And the feasibility of new control in the application of PMSM oil rig is verified.

A Novel Sinusoidal-Wave Permanent Magnetic Motor with High Power Density

A novel high power-density PMSM (permanent magnetic synchronous motor) with independent magnetic flux path for each phase is proposed in the paper. The complex ma thematic model of PMSM is simplified by decoupling of magnetic flux paths between motor phases. In addition, harmonic components are lowered through optimum design of EMF (electric motive force) wave. Thus the ripple torque caused by EMF wave distortion is suppressed. Key words PMSM (permanent magnetic synchronous motor) - phase decoupling - optimum design of back EMF(electric motive force)

Model predictive flux control of permanent magnet synchronous motor driven by three-level inverter based on fine-division strategy

Aiming at the difficulty of setting the weight coefficient in the value function of model predictive torque control(MPTC)for permanent magnet synchronous motor(PMSM)driven by three-level inverter,a fine-division model predictive flux control(MPFC)method is proposed.First,establish a mathematical model between the motor torque and the stator flux linkage according to the mathematical equations of PMSM.Thus,the control of the motor torque and stator flux linkage in the MPTC is transformed into the control of a single stator flux linkage vector,omitting the cumbersome weight setting process in the traditional MPTC.The midpoint potential control strategy is proposed,which uses the characteristics of redundant small vectors to balance the midpoint potential.After that,a fine-division strategy is proposed,which effectively reduces the number of candidate vectors and the computational burden of the system.Finally,the proposed MPFC is compared with MPTC by simulation.The results show that the proposed fine-division MPFC effectively reduces the system calculation,and has the advantages of simple principle and better dynamic and steady-state control performance.The feasibility of the control strategy is verified.

Model predictive torque control of permanent magnet synchronous motor system driven by matrix converter

Employing matrix converter （MC） as driving mode, the strategy of model predictive torque control （MPTC） is proposed for three phase permanent magnet synchronous motor （PMSM） system. MC is applied instead of conventional AC DC AC converter to increase the power factor （PF） of the system input side. MPTC is used to select optimal voltage space vector to enable the system to have satisfactory torque and flux control effect. The resultant MPTC strategy not only makes the MC fed PMSM system operate reliably and have perfect control performance, but also makes the PF of the system input side be 1. Compared with direct torque control （DTC）, the proposed MPTC strategy guarantees that MC fed PMSM has better command following characteristics in the presence of variation of load torque and tracking reference speed. Simulation results verify the feasibility and effectiveness of the proposed strategy.

Robust Control of Permanent Magnet Synchronous Motors

In this paper, permanent magnet synchronous motors (PMSMs) are investigated. According to the feature of PMSMs, a novel state equation of PMSMs is obtained by choosing suitable state variables. Based on the state equation, robust controllers are designed via interval matrix and PI control idea. In terms of bilinear matrix inequations, sufficient conditions for the existence of the robust controller are derived. In order to reduce the conservation and the dependence on parameter, the control inputs of PMSMs are divided into two parts, a feedforward control input and a feedback control input, and relevant sufficient conditions for the existence of the controller are obtained. Because of the suitable choice of state variables, the proposed control strategies can cope with the load uncertainty and have robustness for disturbance. Finally, simulations are carried out via Matlab/Simulink soft to verify the effectiveness of the proposed control strategies. The performance of the proposed control strategies are demonstrated by the simulation results. © 2014 Chinese Association of Automation.

Robust fuzzy sliding-mode control for T-S model based permanent magnet synchronous motor

A fuzzy sliding-mode control (FSMC) scheme based on T-S fuzzy models was proposed for the permanent magnet synchronous motor (PMSM) drive system to solve the speed tracking problem. A T-S fuzzy model was firstly formed to represent the nonlinear system of PMSM. For converting the tracking control into a stabilization problem, a new control design was proposed to define the internal desired states. Then, the FSMC controller for PMSM system with parameter variation and load disturbance was designed based on the fuzzy model. The performance of the proposed controller was verified by experimental results on PMSM system. The results show that the FSMC scheme can drive the dynamics of PMSM into a designated sliding surface in finite time and guarantee the property of asymptotical stability. The information of upper bound of modeling errors as well as perturbations is not required when using the FSMC controller.

A Permanent Magnet Linear Synchronous Motor Drive for HTS Maglev Transportation Systems

A permanent magnet linear synchronous motor （PMLSM） for a high temperature superconducting （HTS） maglev system has been studied, including the motor structure, control strategy, and analysis techniques. Finite element analysis （FEA） of magnetic field is conducted to accurately calculate major motor parameters. Equivalent electrical circuit is used to predict the drive＇s steady-state characteristics, and a phase variable model is applied to predict the dynamic performance. Preliminary experiment with a prototype has been made to verify the theoretical analysis and the HTS-PM synchronous driving technology.

Thermal analysis of surface-mounted permanent magnet synchronous motor for electric vehicle application

As a driving motor, surface mounted permanent magnet synchronous motor exhibits high efficiency and high power density. However, it is susceptible to suffer irreversible demagnetization and insulation failure of coils under severe thermal load condition. Therefore, it is essential to predict temperattrre distribution in the driving motor. In this paper, a lumped parameter thermal mode/of surface mounted permanent magnet is investigated. By using finite element method, the iron loss distribution in various parts of the driving motor is achieved. Moreover, the influences of interface gap and flow rate on temperature distribution are discussed. Finally, the simulation of temperature distribution in different parts of the driving motor is achieved. The presented methodology contributes to verify the feasibility of the driving motor design.

Direct Torque Control of Chaos in Permanent Magnet Synchronous Motor

Permanent magnet synchronous motor（PMSM） displays chaotic osdllation with certain parameter values, which threatens the secure operation of the power system. To control these unwanted chaotic oscillations, a new control scheme which depended on external torque was designed. Based on Lyapunov stability theorem and the matrix theory, several sufficient conditions were derived, which ensured the global asymptotic stability and exponential stability for the chaotic PMSM with uncertain pulse disturbance. The designed controller based on external torque was able to eliminate the chaotic oscillations. A numerical example was given to demonstrate the effectiveness of the proposed results.

基于简化有限集模型预测电流控制的五相PMSM统一容错控制

在五相永磁同步电机(permanent-magnet synchronous motor,PMSM)中,有限集模型预测容错控制(finite control set model predictive fault tolerant control,FCS-MPFTC)存在计算量大、电流谐波含量高等问题。因此,该文提出一种简化FCS-MPFTC来实现相开路和短路故障情况下的统一容错控制。首先,将模型预测电流控制的电流代价函数等效转化为电压代价函数,并采用无差拍方法通过电流模型计算出参考电压。然后,基于抑制三次谐波电流为0的原则合成虚拟电压矢量(virtual voltage vector,V^(3));通过重构V^(3)和扇区,以直接获得参考电压矢量对应的最优电压矢量。最后,对传统和简化FCS-MPFTC在开路和短路故障下进行对比实验。结果表明,所提策略能够有效减小故障后计算量、转矩脉动以及电流谐波含量。