Heat and mass transfer of a porous permeable wall in a high temperature gas dynamical flow is considered. Numerical simulation is conducted on the ground of the conjugate mathematical model which includes filtration a...Heat and mass transfer of a porous permeable wall in a high temperature gas dynamical flow is considered. Numerical simulation is conducted on the ground of the conjugate mathematical model which includes filtration and heat transfer equations in a porous body and boundary layer equations on its surface. Such an approach enables one to take into account complex interaction between heat and mass transfer in the gasdynamical flow and in the structure subjected to this flow. The main attention is given to the impact of the intraporous heat transfer intensity on the transpiration cooling efficiency.展开更多
The BZ19-6 gas field is characterized by high temperature and high pressure (HTHP), high condensate content, little difference between the formation pressure and dew point pressure, and large amount of reverse condens...The BZ19-6 gas field is characterized by high temperature and high pressure (HTHP), high condensate content, little difference between the formation pressure and dew point pressure, and large amount of reverse condensate liquid. During the early stage of depletion development, the production gas-oil ratio (GOR) and production capacity remain relatively stable, which is inconsistent with the conventional reverse condensate seepage law. In view of the static and dynamic conflict in development and production, indoor high-temperature and high-pressure PVT experiment was carried out to reveal the mist-like condensation phenomenon of fluids in the BZ19-6 formation. And the seepage characteristics of condensate gas reservoirs with various degrees of depletion under the condition of HTHP were analyzed based on production performance. The change rule of fluid phase state was analyzed in response to the characterization difficulties of the seepage mechanism. The fluid state was described using the miscible mechanism. And the interphase permeability interpolation coefficient was introduced based on interfacial tension. By doing so, the accurate characterization of the “single-phase flow of condensate gas-near-miscible mist-like quasi single-phase flow-oil-gas two-phase flow” during the development process was achieved. Then the accurate fitting of key indicators for oilfield development was completed, and the distribution law of formation pressure and the law of condensate oil precipitation under different reservoir conditions are obtained. Based on research results, the regulation strategy of variable flow rate production was developed. Currently, the work system has been optimized for 11 wells, achieving a “zero increase” in the GOS of the gas field and an annual oil increase of 22,000 cubic meters.展开更多
In this paper, propagation of sound in pipes under the influence of a gas flow of high temperature is investigated . The analysis in the paper is based on the fundamental equations of fluid mechanics . Approximate for...In this paper, propagation of sound in pipes under the influence of a gas flow of high temperature is investigated . The analysis in the paper is based on the fundamental equations of fluid mechanics . Approximate formulas of the variation of parameters, such as the static tempera -ture, the local velocity of sound , the flow speed and the Mach number, with distance are obtained . The four parameters transmision matix which determines the acoustical character of the pipe is derived and discussed . The acoustical character of a pulsating gas heater is investigated experimentally and theoretically . The theoretical values of the resonant frequencies of the device are in good agreement with the experimental results.展开更多
Five types of coaxial injectors were investigated experimentally using hot hydrogen-rich gas and oxygen-rich gas, which were respectively provided by a GH2/GO2 hydrogen-rich perburner and a GH2/GO2 oxygen-rich preburn...Five types of coaxial injectors were investigated experimentally using hot hydrogen-rich gas and oxygen-rich gas, which were respectively provided by a GH2/GO2 hydrogen-rich perburner and a GH2/GO2 oxygen-rich preburner. The injectors were the shear coaxial injector, the oxidizer post expansion coaxial injector, the fuel impinging coaxial injector, the central body coaxial injector, and the shear tri-coaxial injector. The characteristic velocity efficiency and the combustor＇s wall temperatures were obtained for different design parameters through the experiments. It can be con- cluded that angles of the oxidizer post expansion and the fuel impinging have little influence on the combustion performance and the wall temperatures. The contact area between fuel and oxidizer and the mass flow rate have significant impacts on the combustion performance. The shear tri-coaxial injector has the best combustion performance but also the highest wall temperatures among the five types of injectors.展开更多
The aim of this work is to realize a new numerical program based on the development of a mathematical model allowing determining the parameters of the supersonic flow through a conical shock under hypothesis at high t...The aim of this work is to realize a new numerical program based on the development of a mathematical model allowing determining the parameters of the supersonic flow through a conical shock under hypothesis at high temperature, in the context of correcting the perfect gas model. In this case, the specific heat at constant pressure does not remain constant and varies with the increase of temperature. The stagnation temperature becomes an important parameter in the calculation.The mathematical model is presented by the numerical resolution of a system of first-order nonlinear differential equations with three coupled unknowns for initial conditions. The numerical resolution is made by adapting the higher order Runge Kutta method. The parameters through the conical shock can be determined by considering a new model of an oblique shock at high temperature. All isentropic parameters of after the shock flow depend on the deviation of the flow from the transverse direction. The comparison of the results is done with the perfect gas model for low stagnation temperatures, upstream Mach number and cone deviation angle. A calculation of the error is made between our high temperature model and the perfect gas model. The application is made for air.展开更多
The arc-heated high-temperature gas is rotationally and vibrationally excited, and partially dissociated and ionized. When such gas flows inside a nozzle, energy transfers from rotational and vibrational energy modes ...The arc-heated high-temperature gas is rotationally and vibrationally excited, and partially dissociated and ionized. When such gas flows inside a nozzle, energy transfers from rotational and vibrational energy modes to translational energy mode, and, in addition, recombination reactions occur. These processes are in thermal and chemical nonequilibrium. The present computations treat arc-heated nonequilibrium nozzle flows using a six temperature model (translational, rotational, N2 vibrational, O2 vibrational, NO vibrational and electron temperatures), and nonequilibrium chemical reactions of air. From the calculated flow properties, emission spectra at the nozzle exit were re-constructed by using the code for computing spectra of high temperature air. On the other hand, measurements of N2+(1-) emission spectra were conducted at the nozzle exit in the 20 kW arc-heated wind tunnel. Vibrational and rotational temperatures of N2 were determined using a curve fitting method on N2+(1-) emission spectra, with the vibrational and rotational temperatures for N2 and N2+ being assumed equal. Comparison of the measured and computed results elucidated that the experimental temperatures were larger than the computed ones. At present, we are trying to reveal the main reason for the discrepancy between the computed and measured N2 vibrational and rotational temperatures.展开更多
A 10MW High Temperature Gas Cooled Reactor (HTR-10) designed by the Institute of Nuclear Energy Technology (INET) is now being constructed. The steam generator (SG) in the HTR-10 is one of the most important component...A 10MW High Temperature Gas Cooled Reactor (HTR-10) designed by the Institute of Nuclear Energy Technology (INET) is now being constructed. The steam generator (SG) in the HTR-10 is one of the most important components for reactor safety. The thermal-hydraulic performance of the SG was investigated. A full scale HTR-10 Steam Generator Two Tube Engineering Model Test Facility (SGTM-10) was installed and tested at INET. This paper describes the SGTM-10 thermal hydraulic experimental system in detail. The SGTM-10 simulates the actual thermal and structural parameters of the HTR-10. The SGTM-10 includes three separated loops: the primary helium loop, the secondary water loop, and the tertiary cooling water loop. Two parallel tubes are arranged in the test assembly. The main experimental equipment is shown in the paper. Expermental results are given illustrating the effects of the outlet pressures, the heating power, and the inlet subcooling.展开更多
基金The project supported by the National Natural Science Foundation of China (19889209)Russian Foundation for Basic Research (97-02-16943)
文摘Heat and mass transfer of a porous permeable wall in a high temperature gas dynamical flow is considered. Numerical simulation is conducted on the ground of the conjugate mathematical model which includes filtration and heat transfer equations in a porous body and boundary layer equations on its surface. Such an approach enables one to take into account complex interaction between heat and mass transfer in the gasdynamical flow and in the structure subjected to this flow. The main attention is given to the impact of the intraporous heat transfer intensity on the transpiration cooling efficiency.
文摘The BZ19-6 gas field is characterized by high temperature and high pressure (HTHP), high condensate content, little difference between the formation pressure and dew point pressure, and large amount of reverse condensate liquid. During the early stage of depletion development, the production gas-oil ratio (GOR) and production capacity remain relatively stable, which is inconsistent with the conventional reverse condensate seepage law. In view of the static and dynamic conflict in development and production, indoor high-temperature and high-pressure PVT experiment was carried out to reveal the mist-like condensation phenomenon of fluids in the BZ19-6 formation. And the seepage characteristics of condensate gas reservoirs with various degrees of depletion under the condition of HTHP were analyzed based on production performance. The change rule of fluid phase state was analyzed in response to the characterization difficulties of the seepage mechanism. The fluid state was described using the miscible mechanism. And the interphase permeability interpolation coefficient was introduced based on interfacial tension. By doing so, the accurate characterization of the “single-phase flow of condensate gas-near-miscible mist-like quasi single-phase flow-oil-gas two-phase flow” during the development process was achieved. Then the accurate fitting of key indicators for oilfield development was completed, and the distribution law of formation pressure and the law of condensate oil precipitation under different reservoir conditions are obtained. Based on research results, the regulation strategy of variable flow rate production was developed. Currently, the work system has been optimized for 11 wells, achieving a “zero increase” in the GOS of the gas field and an annual oil increase of 22,000 cubic meters.
文摘In this paper, propagation of sound in pipes under the influence of a gas flow of high temperature is investigated . The analysis in the paper is based on the fundamental equations of fluid mechanics . Approximate formulas of the variation of parameters, such as the static tempera -ture, the local velocity of sound , the flow speed and the Mach number, with distance are obtained . The four parameters transmision matix which determines the acoustical character of the pipe is derived and discussed . The acoustical character of a pulsating gas heater is investigated experimentally and theoretically . The theoretical values of the resonant frequencies of the device are in good agreement with the experimental results.
基金supported by the National High Technology Research and Development Program of China (No.2009AA702504)
文摘Five types of coaxial injectors were investigated experimentally using hot hydrogen-rich gas and oxygen-rich gas, which were respectively provided by a GH2/GO2 hydrogen-rich perburner and a GH2/GO2 oxygen-rich preburner. The injectors were the shear coaxial injector, the oxidizer post expansion coaxial injector, the fuel impinging coaxial injector, the central body coaxial injector, and the shear tri-coaxial injector. The characteristic velocity efficiency and the combustor＇s wall temperatures were obtained for different design parameters through the experiments. It can be con- cluded that angles of the oxidizer post expansion and the fuel impinging have little influence on the combustion performance and the wall temperatures. The contact area between fuel and oxidizer and the mass flow rate have significant impacts on the combustion performance. The shear tri-coaxial injector has the best combustion performance but also the highest wall temperatures among the five types of injectors.
文摘The aim of this work is to realize a new numerical program based on the development of a mathematical model allowing determining the parameters of the supersonic flow through a conical shock under hypothesis at high temperature, in the context of correcting the perfect gas model. In this case, the specific heat at constant pressure does not remain constant and varies with the increase of temperature. The stagnation temperature becomes an important parameter in the calculation.The mathematical model is presented by the numerical resolution of a system of first-order nonlinear differential equations with three coupled unknowns for initial conditions. The numerical resolution is made by adapting the higher order Runge Kutta method. The parameters through the conical shock can be determined by considering a new model of an oblique shock at high temperature. All isentropic parameters of after the shock flow depend on the deviation of the flow from the transverse direction. The comparison of the results is done with the perfect gas model for low stagnation temperatures, upstream Mach number and cone deviation angle. A calculation of the error is made between our high temperature model and the perfect gas model. The application is made for air.
文摘The arc-heated high-temperature gas is rotationally and vibrationally excited, and partially dissociated and ionized. When such gas flows inside a nozzle, energy transfers from rotational and vibrational energy modes to translational energy mode, and, in addition, recombination reactions occur. These processes are in thermal and chemical nonequilibrium. The present computations treat arc-heated nonequilibrium nozzle flows using a six temperature model (translational, rotational, N2 vibrational, O2 vibrational, NO vibrational and electron temperatures), and nonequilibrium chemical reactions of air. From the calculated flow properties, emission spectra at the nozzle exit were re-constructed by using the code for computing spectra of high temperature air. On the other hand, measurements of N2+(1-) emission spectra were conducted at the nozzle exit in the 20 kW arc-heated wind tunnel. Vibrational and rotational temperatures of N2 were determined using a curve fitting method on N2+(1-) emission spectra, with the vibrational and rotational temperatures for N2 and N2+ being assumed equal. Comparison of the measured and computed results elucidated that the experimental temperatures were larger than the computed ones. At present, we are trying to reveal the main reason for the discrepancy between the computed and measured N2 vibrational and rotational temperatures.
基金the State High- Tech Developments Plan of China!(No.86 3- 6 14- 0 2
文摘A 10MW High Temperature Gas Cooled Reactor (HTR-10) designed by the Institute of Nuclear Energy Technology (INET) is now being constructed. The steam generator (SG) in the HTR-10 is one of the most important components for reactor safety. The thermal-hydraulic performance of the SG was investigated. A full scale HTR-10 Steam Generator Two Tube Engineering Model Test Facility (SGTM-10) was installed and tested at INET. This paper describes the SGTM-10 thermal hydraulic experimental system in detail. The SGTM-10 simulates the actual thermal and structural parameters of the HTR-10. The SGTM-10 includes three separated loops: the primary helium loop, the secondary water loop, and the tertiary cooling water loop. Two parallel tubes are arranged in the test assembly. The main experimental equipment is shown in the paper. Expermental results are given illustrating the effects of the outlet pressures, the heating power, and the inlet subcooling.
