A New High Rate Differential Space-Time-Frequency Modulation for MIMO-OFDM

In this paper, we propose a new differential space-time-frequency （DSTF） modulation for MIMOOFDM system with four transmit-antennas and arbitrary receive-antennas, which can improve the transmission rate since it can adopt high order quadrature amplitude modulation （QAM） modulation. Our proposed DSTF scheme embeds some full diversity full rate （FDFR） quasi-orthogonal space-time codes （QOSTBC） with QAM modulation into the frequency intervals and adopts the differential modulation in both time and frequency domains. The simulation results demonstrate that the proposed DSTF scheme can improve transmission rate greatly. Compared with the conventional differential unitary space-time modulation （DUSTM）, it can get better transmission performance in high transmission rate for MIMO-OFDM system.

MMC-MTDC Transmission System with Partially Hybrid Branches

This paper proposes a hybrid submodule modular multilevel converter(MMC)topology which is suitable for multi terminal direct current(MTDC)transmission systems.Each arm of the proposed MMC topology consists of a half-bridge submodule(HBSM)branch and two parallel full-bridge submodule(FBSM)branches.Comparing with the conventional MTDC transmission system,the proposed topology can selectively block the DC fault current and isolate the corresponding fault line without expensive DC circuit breakers(DCCBs).Thus,the influence range of the DC fault can be reduced and the reliability of the power supply can be improved as well.The corresponding modulation and voltage balancing strategies are developed for the proposed hybrid MMC topology.The feasibility of the proposed topology and control strategy is verified in the MATLAB/Simulink simulation.

Highly efficient and stable electrooxidation of methanol and ethanol on 3D Pt catalyst by thermal decomposition of In2O3 nanoshells

In this paper In2O3nanoshells have been synthesized via a facile hydrothermal approach. The nanoshells can be completely cracked into pony-size nanocubes by annealing, which are then used as a support of Pt catalyst for methanol and ethanol electrocatalytic oxidation. The prepared In2O3and supported Pt catalysts (Pt/In2O3) were characterized by X-ray diffraction (XRD), energy dispersive X-ray spectroscopy (EDS), X-ray photoelectron spectroscopy (XPS), field effect scanning electron microscopy (FESEM), and transmission electron microscopy (TEM). Cyclic voltammetry (CV), linear sweep voltammetry (LSV), chronoamperometry and electrochemical impedance spectroscopy (EIS) were carried out, indicating the excellent catalytic performance for alcohol electrooxidation can be achieved on Pt/In2O3nanocatalysts due to the multiple active sites, high conductivity and a mass of microchannels and micropores for reactant diffusions arising from 3D frame structures compared with that on the Pt/C catalysts. ? 2016 Science Press

Reconstruction and transmission of astronomical image based on compressed sensing

In the process of image transmission, the famous JPEG and JPEG-2000 compression methods need more transmission time as it is difficult for them to compress the image with a low compression rate. Recently the compressed sensing（CS） theory was proposed, which has earned great concern as it can compress an image with a low compression rate, meanwhile the original image can be perfectly reconstructed from only a few compressed data. The CS theory is used to transmit the high resolution astronomical image and build the simulation environment where there is communication between the satellite and the Earth. Number experimental results show that the CS theory can effectively reduce the image transmission and reconstruction time. Even with a very low compression rate, it still can recover a higher quality astronomical image than JPEG and JPEG-2000 compression methods.

A Data Transmission Method Using a Cyclic Redundancy Check and Inaudible Frequencies

This paper describes a data transmission method using a cyclic redundancy check and inaudible frequencies.The proposed method uses inaudible high frequencies from 18 k Hz to 22 k Hz generated via the inner speaker of smart devices.Using the proposed method,the performance is evaluated by conducting data transmission tests between a smart book and smart phone.The test results confirm that the proposed method can send 32 bits of data in an average of 235 ms,the transmission success rate reaches 99.47%,and the error detection rate of the cyclic redundancy check is0.53%.

Secured Data Transmission Using Modified LEHS Algorithm in Wireless Sensor Network

In the ancient block Hill cipher, the cipher text is obtained by multiplying the blocks of the plain text with the key matrix. To strengthen the keymatrix, a double guard Hill cipher was proposed with two key matrices, a private key matrix and its modified key matrix along with permutation. In the ancient block Hill cipher, the cipher text is obtained by multiplying the blocks of the plain text with the key matrix. To strengthen the key matrix, a double guard Hill cipher was proposed with two key matrices, a private key matrix and its modified key matrix along with permutation. In this paper a novel modification is performed to the double guard Hill cipher in order to reduce the number of calculation to obtain the cipher text by using non-square matrices. This modified double guard Hill cipher uses a non-square matrix of order (p × q) as its private keymatrix.

Nanoelectronic devices resonant tunnelling diodes grown on InP substrates by molecular beam epitaxy with peak to valley current ratio of 17 at room temperature

This paper reports that InAs/In0.53Ga0.47As/AlAs resonant tunnelling diodes have been grown on InP substrates by molecular beam epitaxy. Peak to valley current ratio of these devices is 17 at 300K. A peak current density of 3kA/cm^2 has been obtained for diodes with AlAs barriers of ten monolayers, and an Ino.53Ga0.47As well of eight monolayers with four monolayers of InAs insert layer. The effects of growth interruption for smoothing potential barrier interfaces have been investigated by high resolution transmission electron microscope.

IN SITU OBSERVATION OF LOWER BAINITIC CARBIDES PRECIPITATION

The lower bainitic carbides precipitation in 40CrMnSiMoV steel previously austempered at 310℃ was observed in situ by employing a high temperature stage of an ultra high voltage TEM(JEM-1000).The typical lower bamitic carbides were found to have precipitated from within the carbide-free bainitic ferrite after tempering for certain period at a temperature higher than that of the isothermal transformation.This revealed that the lower bainitic ferrite is supersaturated with carbon to some extent.The carbide may also precipitate from austenite, but they have no typical morphological features of lower bainitic carbide.

HRTEM Study of Three New Regularly Mixed-layer Structures of B_8S_6 Type in Ca-RE Fluorocarbonate Minerals

The microstructural features of clacium rare earth(Ca RE) fluorocarbonate minerals from Southwest China were studied by using selected area electron diffraction(SAED) and high resolution transmission electron microscopy(HRTEM). Three new regularly mixed layer structures of B 8S 6 type with long period and different stacking sequence, i.e. B 8S 6 Ⅰ, B 8S 6 Ⅱ, and B 8S 6 Ⅲ, were found in the derived polycrystal of parisite, in which their structural symmetry, cell parameters, chemical formulas of crystal and stacking models of structural unit layer, etc. were determined. The results of this study also show that these new regularly mixed layer structrues were formed by order stacking unit layer of bastnaesite(B) and synchisite(S) in varying proportion along c axis. The observation under HRTEM reveals that in the three new regularly mixed layer structures there are different distribution modes of Ce F ion layers, CO 2- 3 ion groups between the Ce F ion layers, and CO 2- 3 ion groups between Ce F and Ca 2+ ion layers, and there are some heterogeneous textures, such as disorder interlayer and stacking fault. It further proves the complexity of the crystal structure of the Ca RE fluorocarbonate minerals.

A low-outgassing-rate carbon fiber array cathode

In this paper, a new carbon fiber based cathode — a low-outgassing-rate carbon fiber array cathode — is investigated experimentally, and the experimental results are compared with those of a polymer velvet cathode. The carbon fiber array cathode is constructed by inserting bunches of carbon fibers into the cylindrical surface of the cathode. In experiment, the diode base pressure is maintained at 1×10^（-2） Pa–2×10^（-2） Pa, and the diode is driven by a compact pulsed power system which can provide a diode voltage of about 100 kV and pulse duration of about 30 ns at a repetition rate of tens of Hz.Real-time pressure data are measured by a magnetron gauge. Under the similar conditions, the experimental results show that the outgassing rate of the carbon fiber array cathode is an order smaller than that of the velvet cathode and that this carbon fiber array cathode has better shot-to-shot stability than the velvet cathode. Hence, this carbon fiber array cathode is demonstrated to be a promising cathode for the radial diode, which can be used in magnetically insulated transmission line oscillator（MILO） and relativistic magnetron（RM）.

Overview of power electronics technology and applications in power generation, transmission and distribution

The main objective of this paper is three-fold.First, to provide an overview of the current status of the power electronics technology, one of the key actors in the upcoming smart grid paradigm enabling maximum power throughputs and near-instantaneous control of voltages and currents in all links of the power system chain. Second, to provide a bridge between the power systems and the power electronic communities, in terms of their differing appreciation of how these devices perform when connected to the power grid. Third, to discuss on the role that the power electronics technology will play in supporting the aims and objectives of future decarbonized power systems. This paper merges the equipment, control techniques and methods used in flexible alternating current transmission systems(FACTS) and high voltage direct transmission(HVDC) equipment to enable a single, coherent approach to address a specific power system problem, using ‘best of breed’ solutions bearing in mind technical, economic and environmental issues.

Nano-Twinning and Martensitic Transformation Behaviors in 316L Austenitic Stainless Steel During Large Tensile Deformation

The evolutions of nano-twins and martensitic transformation in 316L austenitic stainless steel during large tensile deformation were studied by electron backscatter diffraction(EBSD)technology and transmission electron microscopy(TEM)in detail.The results show that due to the low stacking fault energy of the steel,phase transformation induced plasticity(TRIP)and twinning induced plasticity(TWIP)coexist during the tensile deformation.The deformation firstly induces the formation of deformation twins,and dislocation pile-up is caused by the reduction of the dislocation mean free path(MFP)or grain refinement due to the twin boundaries,which further induces the martensitic transformation.With the increase of tensile deformation,a large number of nano-twins andα’-martensite appear,and the width of nano-twins decreases gradually,meanwhile the frequency of the intersecting deformation twins increases.The martensitic transformation can be divided into two types:γ-austenite→α’-martensite andγ-austenite→ε-martensite.α’-martensite is mainly distributed near the twin boundaries,especially at the intersection of twins,whileε-martensite and stacking faults exist in the form of transition products between the twins and the matrix.

FePO4-coated Li[Li0.2Ni0.13Co0.13Mn0.54]O2 with improved cycling performance as cathode material for Li-ion batteries

Li[Li0.2Ni0.13Coo.13Mn0.54]O2 cathode materials were synthesized by carbonate-based co-precipitation method, and then, its surface was coated by thin layers of FePO4. The prepared samples were characterized by X-ray diffraction （XRD）, field emission scanning electron micro- scope （FESEM）, energy-dispersive spectroscopy （EDS）, and transmission electron microscopy （TEM）. The XRD and TEM results suggest that both the pristine and the coated materials have a hexagonal layered structure, and the FePO4 coating layer does not make any major change in the crystal structure. The FePO4-coated sample exhibits both improved initial discharge capacity and columbic efficiency compared to the pristine one. More significantly, the FePO4 coating layer has a much positive influence on the cycling perfor- mance. The FePO4-coated sample exhibits capacity reten- tion of 82 % after 100 cycles at 0.5℃ between 2.0 and 4.8 V, while only 28 % for the pristine one at the same charge-discharge condition. The electrochemical impe- dance spectroscopy （EIS） results indicate that this improved cycling performance could be ascribed to the presence of FePO4 on the surface of Li[Li0.2Ni0.13Co0.13Mno.54102 par- ticle, which helps to protect the cathode from chemical attacks by HF and thus suppresses the large increase in charge transfer resistance.

The Effects of Different HITRAN Versions on Calculated Long-Wave Radiation and Uncertainty Evaluation

Four editions of the High Resolution Transmission （HITRAN） databases （HITRAN96, HITRAN2K, HITRAN04, and HITRAN08） are compared by using a line-by-line （LBL） radiative model in the long-wave calculation for six typical atmospheres. The results show that differences in downward radiative fluxes between HITRAN96 and HITRAN08 at the surface can reach a maximum of 1.70 W m-2 for tropical atmospheres. The largest difference in heating rate between HITRAN96 and HITRAN08 can reach 0.1 K day-1 for midlatitude summer atmosphere. Uncertainties caused by line intensity and air-broadened half- widths are also evaluated in this work using the uncertainty codes given in HITRAN08. The uncertainty is found to be 1.92 W m-2 for upward fluxes at the top of the atmosphere （TOA） and 1.97 W m-2 for downward fluxes at the surface. The largest heating rate caused by the uncertainty of line intensity and air-broadened hMf-width can reach 0.5 K day-1. The differences in optical depths between 1300 and 1700 cm-1 caused by different HITRAN versions are larger than those caused by the uncertainties in intensity and air-broadened half-width. This paper suggests that there is inaccurate representation of line parameters over some spectral ranges in HITRAN and more attention should be paid to these ranges in fields such as remote sensing.

Influence of the Cd/S Molar Ratio on the Optical and Structural Properties of Nanocrystalline CdS Thin Films

Nanocrystalline CdS thin films have been deposited using precursors with different thiourea concentrationonto glass substrates by sol-gel spin coating method.The crystalline nature of the films has been observedto be strongly dependent on thiourea concentration and annealing temperature.The CdS films are found tobe nanocrystalline in nature with hexagonal structure.The grain size is found to be in the range of 7.6 to11.5 nm depending on the thiourea concentration and annealing temperature.The high resolution transmissionelectron microscopy （HRTEM） results of the CdS films prepared using cadmium to thiourea molar ratio of0.3：0.3 indicate the formation of nanocrystalline CdS with grain size of 5 nm.Fourier transform infrared （FTIR）analysis shows the absorption bands corresponding to Cd and S.The optical study carried out to determinethe band gap of the nanostructured CdS thin films shows a strong blue shift.The band gap energy has beenobserved to lie in the range of 3.97 to 3.62 eV following closely the quantum confinement dependence ofenergy on crystallite radius.The dependence of band gap of the CdS films on the annealing temperature andthiourea concentration has also been studied.The photoluminescence （PL） spectra display two main emissionpeaks corresponding to the blue and green emissions of CdS.

Precipitate Phases in an 11% Cr Ferritic/Martensitic Steel with Tempering and Creep Conditions

Precipitates in an 11% Cr ferritic/martensitic steel containing Nd with tempering and creep conditions were investigated using transmission electron microscope with energy-dispersive X-ray spectroscopy. The precipitates in the steel with a tempering condition were identified to be Cr-rich M23C6 carbide, Nb-rich/V-rich/Ta–Nb-rich MX carbides, Nbrich MX carbonitride, and Fe-rich M5C2 carbide. Nd-rich carbonitride, which is not known to have been reported previously in steels, was also detected in the steel after tempering. Most of the Nb-rich MX precipitates were dissolved, whereas the amount of Ta-rich MX precipitates was increased significantly in the steel after a creep test at 600 °C at an applied stress of180 MPa for 1,100 h. No Fe2 W Laves phase has been detected in the steel after tempering.（Fe, Cr）2W Laves phase with a relatively large size was observed in the steel after the creep test.