Performance of CO_2 absorption in a diameter-varying spray tower

The application of spray towers for CO2 capture is a development trend in recent years. However, most of the previous jobs were conducted in a cylindrical tower by using a single spray nozzle, whose configuration and performance is not good enough for industrial application. To solve this problem, the present work proposed a diameter-varying spray tower and a new spray mode of dual-nozzle opposed impinging spray to enhance the heat and mass transfer of CO2 absorption process. Experiments were performed to investigate the mass transfer performance （in terms of the CO2 removal rate （η） and the overall mass transfer coefficient （KGae）） of the improved spray tower under various operating conditions. Experimental results showed that the liquid to gas ratio and mole ratio of MEA to C02 are major factors, which affect the absorption performance and the maximums of η and KGae that are 94.0% and 0.574 kmol. m^-3·h^-1·kPa^-1, respectively, under the experimental conditions. Furthermore, new correlations to predict the mass transfer coefficient of the proposed spray tower are developed in various CO2 concentrations with a Pearson Correlation Coefficient over 90%.

Spray Effect on the Thermal Performances of a Dry Cooling Tower

Pre-cooling the inlet air of a dry cooling tower by means of a spray can improve the tower performance during periods of high temperature.To study the spray effect on the thermal performance of natural draft dry cooling towers(NDDCTs),in this study 3-D numerical simulations of such a process have been conducted using Fluent 16.2(a two-way coupled Eulerian-Lagrangian approach).The considered NDDCT is 120 m high and only half system is simulated due to its structural symmetry.Three different spray strategies have been investigated at a typical crosswind speed of 4 m/s,which is the most frequent wind speed.The results have shown that:(1)The three implemented spray strategies can improve the thermal performance of the studied NDDCT with a vary-ing degree of success.In one case,the heat rejection rate can be increased by 35.2%,and the tower outlet water temperature can be decreased by 2.1℃ when compared with the no spray case;(2)To improve the thermal per-formance of the NDDCT using a small amount of water,the design of the spray pre-cooling system must include more nozzles on the windward and fewer or even no nozzles on the leeward sides of the NDDCT.

An Innovated Tower-fluidized Bed Prilling Process

Cooling-solidification of sprayed droplets is one of major methods for prilling of melt.Traditionally, this is carried out in an empty tower,and the equipment requirement for producing larger particles is very high,resulting in not only significant cost increasing but also difficulties in transporting melt etc.Based on analysis and simulation,a new prilling process is developed for the melt prilling,which combines a tower with a fluidized bed so that the height of equipment is greatly decreased,and it exhibits satisfactory performance in industrial application. Mathematical model for tower prilling,its simulated results,the structure of the equipment for the innovated prilling process and its application are addressed.

Polyethoxylation and polypropoxylation reactions：Kinetics,mass transfer and industrial reactor design

Ethoxylation and propoxylation reactions are performed in the industry to produce mainly non-ionic surfactants and ethylene oxide(EO)–propylene oxide(PO) copolymers.Both the reactions occur in gas–liquid reactors by feeding gaseous EO,PO or both into the reactor containing a solution of an alkaline catalyst(KOH or Na OH).Non-ionic surfactants are produced by using liquid starters like fatty alcohols,fatty acids or alkyl-phenols,while when the scope is to prepare EO–PO copolymers the starter can be a mono-or multi-functional alcohol of low molecular weight.Both reactions are strongly exothermic,and EO and PO,in some conditions,can give place to runaway and also to explosive side reactions.Therefore,the choice of a suitable reactor is a key factor for operating in safe conditions.A correct reactor design requires:(i) the knowledge of the kinetic laws governing the rates of the occurring reactions;(ii) the role of mass and heat transfer in affecting the reaction rate;(iii) the solubility of EO and PO in the reacting mixture with the non-ideality of the reacting solutions considered;(iv) the density of the reacting mixture.All these aspects have been studied by our research group for different starters of industrial interest,and the data collected by using semibatch well stirred laboratory reactors have been employed for the simulation of industrial reactors,in particular Gas–Liquid Spray Tower Loop Reactors.

Evaporative Cooling Applied in Thermal Power Plants:A Review of the State-ofthe-Art and Typical Case Studies

A review is conducted about the application of the evaporative cooling technology in thermal power plants.Different case studies are considered,namely,evaporative air conditioners,evaporative cooling in direct air-cooled systems,gas turbine inlet cooling,wet cooling towers,and hybrid cooling towers with a crosswind effect.Some effort is provided to describe the advantages related to direct evaporative cooling when it is applied in thermal power plants and illustrate the research gaps,which have not been filled yet.In particular,typical case studies are intentionally used to compare the cooling performances when direct evaporative cooling is implemented in different types of cooling towers,including the natural draft wet cooling tower(NDWCT)and the pre-cooled natural draft dry cooling tower(NDDCT).It is shown that the NDWCT provides the best cooling performance in terms of power station cooling,followed by the pre-cooled NDDCT,and the NDDCT;moreover,the evaporative pre-cooling is able to enhance the cooling performance of NDDCT.Besides,on a yearly basis,better NDDCT cooling performances can be obtained by means of a spray-based pre-cooling approach with respect to wet media pre-cooling.Therefore,the use of nozzle spray is suggested for improvement in the performance of indirect/direct air-cooling systems with controlled water consumption.

Recent Development of Dielectric Elastomer Transducers and Potential Applications

Power generation using dielectric elastomer transducers is cheap, light, stackable, easy to install, and highly efficient. Also, since the dielectric elastomer transducer is an actuator developed into an artificial muscle, if the DE motor is further developed, it might be possibly be able to drive a vehicle. Efficient robot driving, various industrial machines and the use of dielectric elastomer sensors to optimize the driving may also help solve the above problems from the perspective of eco-driving. This paper describes the latest level of development of dielectric elastomers, their main problems and solutions to these problems, and their potential applications. The possibilities and concrete plans for building local global smart cities (including local generation power for local consumption), efficient transportation, and environmental monitoring systems utilizing dielectric elastomers are also discussed.