Experimental and Finite Element Analysis of Corroded High-Pressure Pipeline Repaired by Laminated Composite

Repairs of corroded high-pressure pipelines are essential for fluids transportation under high pressure.One of the methods used in their repairs is the use of layered composites.The composite used must have the necessary strength.Therefore,the experiments and analytical solutions presented in this paper are performed according to the relevant standards and codes,including ASME PCC-2,ASME B31.8S,ASME B31.4,ISO 24817 and ASME B31.G.In addition,the experimental tests are replicated numerically using the finite element method.Setting the strain gauges at different distances from the defect location,can reduce the nonlinear effects,deformation,and fluctuations due to the high pressure.The direct relationship between the depth of an axial defect and the stress concentration is observed at the inner side edges of the defect.Composite reparation reduces the non-linearities related to the sharp variation of the geometry and a more reliable numerical simulation could be performed.

A study of hydrate plug formation in a subsea natural gas pipeline using a novel high-pressure flow loop

The natural gas pipeline from Platform QKI8-1 in the southwest of Bohai Bay to the onshore processing facility is a subsea wet gas pipeline exposed to high pressure and low temperature for a long distance. Blockages in the pipeline occur occasionally. To maintain the natural gas flow in the pipeline, we proposed a method for analyzing blockages and ascribed them to the hydrate formation and agglomeration. A new high-pressure flow loop was developed to investigate hydrate plug formation and hydrate particle size, using a mixture of diesel oil, water, and natural gas as experimental fluids. The influences of pressure and initial flow rate were also studied. Experimental results indicated that when the flow rate was below 850 kg/h, gas hydrates would form and then plug the pipeline, even at a low water content （10%） of a water/oil emulsion. Furthermore, some practical suggestions were made for daily management of the subsea pipeline.

Gas Film Disturbance Characteristics Analysis of High-Speed and High-Pressure Dry Gas Seal

The dry gas seal（DGS） has been widely used in high parameters centrifugal compressor, but the intense vibrations of shafting, especially in high-speed condition, usually result in DGS＇s failure. So the DGS＇s ability of resisting outside interference has become a determining factor of the further development of centrifugal compressor. However, the systematic researches of which about gas film disturbance characteristics of high parameters DGS are very little. In order to study gas film disturbance characteristics of high-speed and high-pressure spiral groove dry gas seal（S-DGS） with a flexibly mounted stator, rotor axial runout and misalignment are taken into consideration, and the finite difference method and analytical method are used to analyze the influence of gas film thickness disturbance on sealing performance parameters, what＇s more, the effects of many key factors on gas film thickness disturbance are systematically investigated. The results show that, when sealed pressure is 10.1MPa and seal face average linear velocity is 107.3 m/s, gas film thickness disturbance has a significant effect on leakage rate, but has relatively litter effect on open force; Excessively large excitation amplitude or excessively high excitation frequency can lead to severe gas film thickness disturbance; And it is beneficial to assure a smaller gas film thickness disturbance when the stator material density is between 3.1 g/cm3 to 8.4 g/cm3; Ensuring sealing performance while minimizing support axial stiffness and support axial damping can help to improve dynamic tracking property of dry gas seal. The proposed research provides the instruction to optimize dynamic tracking property of the DGS.

Numerical Simulation Analysis of the Transformer Fire Extinguishing Process with a High-Pressure Water Mist System under Different Conditions

To thoroughly study the extinguishing effect of a high-pressure water mist fire extinguishing system when a transformer fire occurs,a 3D experimental model of a transformer is established in this work by employing Fire Dynamics Simulator(FDS)software.More specifically,by setting different parameters,the process of the highpressure water mist fire extinguishing system with the presence of both diverse ambient temperatures and water mist sprinkler laying conditions is simulated.In addition,the fire extinguishing effect of the employed high-pressure water mist system with the implementation of different strategies is systematically analyzed.The extracted results show that a fire source farther away fromthe centerline leads to a lower local temperature distribution.In addition,as the ambient temperature increases,the temperature above the fire source decreases,while the temperature and the concentrationof theupperflue gas layer bothdecrease.Interestingly,after thehigh-pressurewatermist sprinkler begins to operate,both the temperature distribution above the fire source and the concentration of the flue gas decrease,which indicates that the high-pressure water mist system plays the role of cooling and dust removal.By comparing various sprinkler laying methods,it is found that the lower sprinkler height has a better effect on the temperature above the fire source,the temperature of the upper flue gas layer,and the concentration of the flue gas.Moreover,when the sprinkler is spread over thewhole transformer,the cooling effect on both the temperature above the fire source and the temperature of the upper flue gas layer is good,whereas the change in the concentration of the flue gas above the fire source is not obvious compared to the case where the sprinkler is not fully spread.

Effects of ultrasound on the desulfurization performance of hot coal gas over Zn-Mn-Cu supported on semi-coke sorbent prepared by high-pressure impregnation method

Zn-Mn-Cu/SC（U） sorbent was hydrothermally synthesized by ultrasound-assisted high-pressure impregnation method with semi-coke（SC）as support and the mixed solution of zinc nitrate,manganese nitrate and copper nitrate as active component precursors.The desulfurization performances of hot coal gas on the prepared sorbent at a mid-temperature of 500°C were tested in fixed-bed reactor.Morphology and pore structure of the prepared sorbent were also characterized by TEM,N2adsorption/desorption isotherms and XRD.For comparison,the sorbent of Zn-Mn-Cu/SC prepared by conventional high-pressure impregnation was also evaluated and characterized in order to study the effects of ultrasound treatment.Zn-Mn-Cu/SC（U） sorbent prepared by high-pressure impregnation under ultrasound-assisted condition showed a better desulfurization performance than Zn-Mn-Cu/SC.It could remove H2 S from 1000×10-6m3/m3 to 0.1×10-6m3/m3 at 500°C and maintained for 12.5 h with the sulfur capacity of 7.74%,in which both the breakthrough time and sulfur capacity were about 32% and 51% higher than those of Zn-Mn-Cu/SC sorbent.The introduction of ultrasound during high-pressure impregnation process greatly improved the morphology and pore structure of the sorbent.The ultrasonic treatment made particle size of active components smaller and made them more evenly disperse on semi-coke support,which provided more opportunities to contact with H2S in coal-based gases.However,there were no any difference in compositions and existing forms of active components on the Zn-Mn-Cu/SC and Zn-Mn-Cu/SC（U） sorbents.

A new transition metal diphosphideα-MoP_(2) synthesized by a high-temperature and high-pressure technique

Monoclinicα-MoP_(2),with the OsGe2-type structure(space group C2/m,Z=4)and lattice parameters a=8.7248(11)Å,b=3.2322(4)Å,c=7.4724(9)Å,andβ=119.263°,was synthesized under a pressure of 4~GPa at a temperature between 1100℃and 1200℃.The structure ofα-MoP_(2) and its relationship to other transition metal diphosphides are discussed.Surprisingly,the ambient pressure phase orthorhombicβ-MoP_(2)(space group Cmc21)is denser in structure thanα-MoP_(2).Room-temperature high-pressure x-ray diffraction studies exclude the possibility of phase transition fromβ-MoP_(2) to α-MoP_(2),suggesting thatα-MoP_(2) is a stable phase at ambient conditions;this is also supported by the total energy and phonon calculations.

基于GAS算法的卵砾石粒径自动识别应用研究

粒径和级配是表征床面组成的重要指标,基于GAS粒径自动识别技术可自动识别粗粒床面粒径并生成级配曲线,能够大幅提高现场采样和分析的效率。为了验证GAS的分割效果,采用GAS提供的默认参数进行分割,同时应用ImageJ软件手动分割进行验证。结果表明:GAS级配曲线的相对误差为5.7%,相关系数为0.992。另外,采用单参数和多参数敏感性分析法来标准化参数调整方案,gre、can1和can2对GAS提取的级配曲线和特征粒径有显著影响,其中gre起主导作用,而can1和can2控制着砾石边界的检测完整性。

High-pressure new phases of V–N compounds

The high-pressure diagram of V–N compounds is enriched by proposed seven new stable high-pressure phases.The P-1-VN_4with the armchair N-rich structure may be quenched to ambient conditions.The formed N–N covalent bond plays an important role for the structural stability of N-chain.The charge transfer results in a V–N ionic bond interaction,which further improves the stability of N-chain structure.The P-1-VN_4,P4mnc-VN_8,and Immm-VN_(10)with the outstanding detonation properties have potential application in explosive field.

The discovery of TiO_(2)-Ⅱ,the α-PbO_(2)-structured high-pressure polymorph of rutile,in the Suizhou L6 chondrite

We report the discovery of TiO_(2)-Ⅱ in the unmelted rock of the shocked Suizhou L6 chondrite.Natural TiO_(2)-Ⅱ was previously found in ultrahigh-pressure metamorphic and mantle-derived rocks,terrestrial impact structures,and tektite.Our microscopic,Raman spectroscopic,electron microprobe and transmission electron microscopic investigations have revealed:(1) All observed TiO_(2)-Ⅱ grains are related with ilmenite and pyrophanite;(2) TiO_(2)-Ⅱ occurs as needle-and leaf-shaped inclusions in llmenite and patch-,tape-shaped body in pyrophanite;(3)The composition of TiO_(2)-Ⅱ is identical with that of its precursor rutile;(4) The Raman spectrum of TiO_(2)-Ⅱ is in good agreement with that of natural and synthesized α-PbO_(2)-type TiO_(2);(5) TiO_(2)-Ⅱ occurs mainly in the form of well-ordered nano-domains and small mis-orientation among the domains can be observed.(6) All electron diffraction reflections from TiO_(2)-Ⅱ can be indexed to α-PbO_(2)structure in space group Pbcn with lattice parameters of a=4.481 ?,b=5.578 A and c=4.921 A;(7) The exsolution inclusions of rutile from host ilmenite are mostly connected with an alternation process along the lamellar twinning plane of ilmenite induced by shockinduced high pressure and high temperature;(8) The P-T regime of 20-25 GPa and 1000 ℃ estimated for the Suizhou unmelted rock is suitable for phase transition of rutile into TiO_(2)-Ⅱ phase.

Repositioning fertilizer manufacturing subsidies for improving food security and reducing greenhouse gas emissions in China

China removed fertilizer manufacturing subsidies from 2015 to 2018 to bolster market-oriented reforms and foster environmentally sustainable practices.However,the impact of this policy reform on food security and the environment remains inadequately evaluated.Moreover,although green and low-carbon technologies offer environmental advantages,their widespread adoption is hindered by prohibitively high costs.This study analyzes the impact of removing fertilizer manufacturing subsidies and explores the potential feasibility of redirecting fertilizer manufacturing subsidies to invest in the diffusion of these technologies.Utilizing the China Agricultural University Agri-food Systems model,we analyzed the potential for achieving mutually beneficial outcomes regarding food security and environmental sustainability.The findings indicate that removing fertilizer manufacturing subsidies has reduced greenhouse gas(GHG)emissions from agricultural activities by 3.88 million metric tons,with minimal impact on food production.Redirecting fertilizer manufacturing subsidies to invest in green and low-carbon technologies,including slow and controlled-release fertilizer,organic-inorganic compound fertilizers,and machine deep placement of fertilizer,emerges as a strategy to concurrently curtail GHG emissions,ensure food security,and secure robust economic returns.Finally,we propose a comprehensive set of government interventions,including subsidies,field guidance,and improved extension systems,to promote the widespread adoption of these technologies.

A developed dual-site Langmuir model to represent the high-pressure methane adsorption and thermodynamic parameters in shale

Comprehending the mechanism of methane adsorption in shales is a crucial step towards optimizing the development of deep-buried shale gas. This is because the methane adsorbed in shale represents a significant proportion of the subsurface shale gas resource. To properly characterize the methane adsorption on shale, which exhibits diverse mineral compositions and multi-scale pore sizes, it is crucial to capture the energy heterogeneity of the adsorption sites. In this paper, a dual-site Langmuir model is proposed, which accounts for the temperature and pressure dependence of the density of the adsorbed phase. The model is applied to the isothermals of methane adsorption on shale, at pressures of up to 30 MPa and temperatures ranging from 40 to 100 ℃. The results show that the proposed model can describe the adsorption behavior of methane on shale more accurately than conventional models, which assume a constant value for the density of adsorbed phase. Furthermore, the proposed model can be extrapolated to higher temperatures and pressures. Thermodynamic parameters were analyzed using correctly derived equations. The results indicate that the widely used, but incorrect, equation would underestimate the isosteric heat of adsorption. Neglecting the real gas behavior, volume of the adsorbed phase, and energy heterogeneity of the adsorption sites can lead to overestimation of the isosteric heat of adsorption. Furthermore, the isosteric heat evaluated from excess adsorption data can only be used to make a rough estimate of the real isosteric heat at very low pressure.

低维GaS高响应度纸基光电探测器

随着石墨烯的发现,二维材料因其与众不同的理化性质,而在科研领域的关注度与日俱增.以石墨烯为起点的二维材料(例如MoS_(2),WS_(2),GaS等)因在器件中具有较好的光电性质和较高的迁移率,而在生产和生活中具有良好的应用前景.本文简要探讨了光电导效应的原理,采用铅笔勾勒的方法绘制出了石墨电极,并采用体材料液相超声后分散液滴涂的方法,制备了宏观尺度的GaS纸基光电探测器,该探测器具有可见光范围的光电响应,且具有较好的机械重复性.本文介绍的纸基光电探测器的制备方法对于高校基础物理和半导体物理课程的教学具有实际意义,有利于学生更好地理解光电导效应的原理.此外,纸基光电探测器不仅降低了制备成本,而且还有助于提高高校学生的科研实践能力.

GAS6-AS1调节miR-370-3p/SPATA2轴对卵巢癌细胞增殖、迁移、侵袭、凋亡和EMT的影响

目的:探讨长链非编码RNA GAS6反义RNA1(long non-coding RNA GAS6 antisense RNA1, lncRNA GAS6-AS1)调节miR-370-3p/精子发生相关蛋白2 (spermatogenesis-associated protein 2, SPATA2)轴对卵巢癌细胞增殖、迁移、侵袭、凋亡和上皮间质转化(epithelial mesenchymal transformation, EMT)的影响。方法:qRT-PCR、Western blot分别检测癌旁组织、卵巢癌组织、人正常卵巢上皮细胞IOSE80及卵巢癌细胞系HO-8910、SKOV3、A2780中GAS6-AS1、miR-370-3p及SPATA2蛋白表达。将SKOV3细胞分为:对照组(NC组)、 si-NC组、si-GAS6-AS1组、mimic NC组、miR-370-3p mimic组、si-GAS6-AS1+inhibitor NC组、si-GAS6-AS1+miR-370-3p inhibitor组,qRT-PCR检测细胞中GAS6-AS1、miR-370-3p表达;CCK-8法检测细胞增殖;流式细胞术检测细胞凋亡;划痕愈合实验检测细胞迁移;Transwell实验检测细胞侵袭;Western blot检测SPATA2、细胞周期素D1(CyclinD1)、Bcl-2相关X蛋白(Bcl-2-associated X,Bax)、E-钙黏蛋白(E-cadherin)、波形蛋白(Vimentin)、神经钙黏蛋白(N-cadherin)表达;双荧光素酶报告基因实验检测GAS6-AS1与miR-370-3p、 miR-370-3p与SPATA2的关系。结果:在卵巢癌组织和细胞中GAS6-AS1、SPATA2蛋白高表达,miR-370-3p低表达,且在SKOV3细胞中GAS6-AS1、SPATA2蛋白表达量最高,miR-370-3p表达水平最低,因此,选择SKOV3细胞为后续研究对象。与NC组、si-NC组比较,si-GAS6-AS1组GAS6-AS1、OD450值(24 h、48 h、72 h)、划痕愈合率、侵袭细胞数、SPATA2、CyclinD1、Vimentin、N-cadherin蛋白表达降低,miR-370-3p表达、细胞凋亡率、Bax、E-cadherin蛋白表达升高(P<0.05);与NC组、mimic NC组比较,miR-370-3p mimic组OD450值(24 h、48 h、72 h)、划痕愈合率、侵袭细胞数、SPATA2、CyclinD1、Vimentin、N-cadherin蛋白表达降低,miR-370-3p表达、细胞凋亡率、Bax、E-cadherin蛋白表达升高(P<0.05);miR-370-3p inhibitor减弱了沉默GAS6-AS1对SKOV3细胞增殖、迁移、侵袭及EMT的抑制及对细胞凋亡的促进作用。GAS6-AS1与miR-370-3p、miR-370-3p与SPATA2存在靶向调控关系。结论:沉默GAS6-AS1通过上调miR-370-3p来抑制SPATA2表达,从而抑制SKOV3细胞增殖、迁移、侵袭及EMT,并促进细胞凋亡。

Numerical Investigation of Combined Production of Natural Gas Hydrate and Conventional Gas

Natural gas hydrate(NGH)is generally produced and accumulated together with the underlying conventional gas.Therefore,optimizing the production technology of these two gases should be seen as a relevant way to effectively reduce the exploitation cost of the gas hydrate.In this study,three types of models accounting for the coexistence of these gases are considered.Type A considers the upper hydrate-bearing layer(HBL)adjacent to the lower conventional gas layer(CGL);with the Type B a permeable interlayer exists between the upper HBL and the lower CGL;with the type C there is an impermeable interlayer between the upper HBL and the lower CGL.The production performances associated with the above three models are calculated under different conditions,including only a depressurized HBL(only HBL DP);only a depressurized CGL(only CGL DP);and both the HBL and the CGL being depressurized(HBL+CGL DP).The results show that for Type A and Type B coexistence accumulation models,when only HBL or CGL is depressurized,the gas from the other layer will flow into the production layer due to the pressure difference between the two layers.In the coexistence accumulation model of type C,the cumulative gas production is much lower than that of Type A and Type B,regardless of whether only HBL DP,only CGL DP,or HBL+CGL DP are considered.This indicates that the impermeable interlayer restricts the cross-flow of gas between HBL and CGL.For three different coexistence accumulation models,CGL DP has the largest gas-to-water ratio.

Productivity Analysis Method of Abnormal High-Pressure Gas Reservoir in Ying-Qiong Basin

Ying-Qiong Basin in the west of South China Sea contains plenty of abnormal high-pressure gas reservoirs, whose stress sensitivity is crucial for well productivity. To explore the influence of stress sensitivity on production, the variable outlet back pressure stress sensitivity experiments were applied to test core sample permeability under different burden pressure and obtain the relational expression of power function of core stress sensitivity. Afterwards, new productivity equation is deduced in consideration of reservoir stress sensitivity, and the affection of stress sensitivity on production is analyzed. The result demonstrates close link between stress sensitivity and productivity, since single well production decreases dramatically when reservoir stress sensitivity has been taken into account. This research is constructive for well-testing data interpretation in stress sensitive gas reservoirs.

Microscopic experiment on efficient construction of underground gas storages converted from water-invaded gas reservoirs

Based on the microfluidic technology,a microscopic visualization model was used to simulate the gas injection process in the initial construction stage and the bottom water invasion/gas injection process in the cyclical injection-production stage of the underground gas storage(UGS)rebuilt from water-invaded gas reservoirs.Through analysis of the gas-liquid contact stabilization mechanism,flow and occurrence,the optimal control method for lifecycle efficient operation of UGS was explored.The results show that in the initial construction stage of UGS,the action of gravity should be fully utilized by regulating the gas injection rate,so as to ensure the macroscopically stable migration of the gas-liquid contact,and greatly improve the gas sweeping capacity,providing a large pore space for gas storage in the subsequent cyclical injection-production stage.In the cyclical injection-production stage of UGS,a constant gas storage and production rate leads to a low pore space utilization.Gradually increasing the gas storage and production rate,that is,transitioning from small volume to large volume,can continuously break the hydraulic equilibrium of the remaining fluid in the porous media,which then expands the pore space and flow channels.This is conducive to the expansion of UGS capacity and efficiency for purpose of peak shaving and supply guarantee.

Deep-large faults controlling on the distribution of the venting gas hydrate system in the middle of the Qiongdongnan Basin, South China Sea

Many locations with concentrated hydrates at vents have confirmed the presence of abundant thermogenic gas in the middle of the Qiongdongnan Basin(QDNB).However,the impact of deep structures on gasbearing fluids migration and gas hydrates distribution in tectonically inactive regions is still unclear.In this study,the authors apply high-resolution 3D seismic and logging while drilling(LWD)data from the middle of the QDNB to investigate the influence of deep-large faults on gas chimneys and preferred gasescape pipes.The findings reveal the following:(1)Two significant deep-large faults,F1 and F2,developed on the edge of the Songnan Low Uplift,control the dominant migration of thermogenic hydrocarbons and determine the initial locations of gas chimneys.(2)The formation of gas chimneys is likely related to fault activation and reactivation.Gas chimney 1 is primarily arises from convergent fluid migration resulting from the intersection of the two faults,while the gas chimney 2 benefits from a steeper fault plane and shorter migration distance of fault F2.(3)Most gas-escape pipes are situated near the apex of the two faults.Their reactivations facilitate free gas flow into the GHSZ and contribute to the formation of fracture‐filling hydrates.

New insights into the deposition of natural gas hydrate on pipeline surfaces:A molecular dynamics simulation study

Natural gas hydrate(NGH)can cause pipeline blockages during the transportation of oil and gas under high pressures and low temperatures.Reducing hydrate adhesion on pipelines is viewed as an efficient way to prevent NGH blockages.Previous studies suggested the water film can greatly increase hydrate adhesion in gas-dominant system.Herein,by performing the molecular dynamics simulations,we find in water-dominant system,the water film plays different roles in hydrate deposition on Fe and its corrosion surfaces.Specifically,due to the strong affinity of water on Fe surface,the deposited hydrate cannot convert the adsorbed water into hydrate,thus,a water film exists.As water affinities decrease(Fe>Fe_(2)O_(3)>FeO>Fe_(3)O_(4)),adsorbed water would convert to amorphous hydrate on Fe_(2)O_(3)and form the ordered hydrate on FeO and Fe_(3)O_(4)after hydrate deposition.While absorbed water film converts to amorphous or to hydrate,the adhesion strength of hydrate continuously increases(Fe<Fe_(2)O_(3)<FeO<Fe_(3)O_(4)).This is because the detachment of deposited hydrate prefers to occur at soft region of liquid layer,the process of which becomes harder as liquid layer vanishes.As a result,contrary to gas-dominant system,the water film plays the weakening roles on hydrate adhesion in water-dominant system.Overall,our results can help to better understand the hydrate deposition mechanisms on Fe and its corrosion surfaces and suggest hydrate deposition can be adjusted by changing water affinities on pipeline surfaces.

Peri-implant gas accumulation in response to magnesium-based musculoskeletal biomaterials:Reframing current evidence for preclinical research and clinical evaluation

Historically,the rapid degradation and massive gas release from magnesium(Mg)implants resulted in severe emphysema and mechanical failure.With the advent of new alloys and surface treatment methods,optimized Mg implants have re-entered clinics since last decade with reliable performance.However,the optimization aims at slowing down the degradation process,rather than exemption of the gas release.This study involved a systematic evaluation of current preclinical and clinical evidence,regarding the physical signs,symptoms,radiological features,pathological findings and complications potentially associated with peri±implant gas accumulation(PIGA)after musculoskeletal Mg implantation.The literature search identified 196 potentially relevant publications,and 51 papers were enrolled for further analysis,including 22 preclinical tests and 29 clinical studies published from 2005 to 2023.Various Mg-based materials have been evaluated in animal research,and the application of pure Mg and Mg alloys have been reported in clinical follow-ups involving multiple anatomical sites and musculoskeletal disorders.Soft tissue and intraosseous PIGA are common in both animal tests and clinical follow-ups,and potentially associated with certain adverse events.Radiological examinations especially micro-CT and clinical CT scans provide valuable information for quantitative and longitudinal analysis.While according to simulation tests involving Mg implantation and chemical processing,tissue fixation could lead to an increase in the volume of gas cavity,thus the results obtained from ex vivo imaging or histopathological evaluations should be interpreted with caution.There still lacks standardized procedures or consensus for both preclinical and clinical evaluation of PIGA.However,by providing focused insights into the topic,this evidence-based study will facilitate future animal tests and clinical evaluations,and support developing biocompatible Mg implants for the treatment of musculoskeletal disorders.

Effect of grain size on gas bubble evolution in nuclear fuel:Phase-field investigations

Numerous irradiation-induced gas bubbles are created in the nuclear fuel during irradiation, leading to the change of microstructure and the degradation of mechanical and thermal properties. The grain size of fuel is one of the important factors affecting bubble evolution. In current study, we first predict the thermodynamic behaviors of point defects as well as the interplay between vacancy and gas atom in both UO_(2) and U_(3)Si_(2) according to ab initio approach. Then, we establish the irradiation-induced bubble phase-field model to investigate the formation and evolution of intra-and inter-granular gas bubbles. The effects of fission rate and temperature on the evolutions of bubble morphologies in UO_(2) and U_(3)Si_(2) have been revealed. Especially, a comparison of porosities under different grain sizes is examined and analyzed. To understand the thermal conductivity as functions of grain size and porosity, the heat transfer capability of U_(3)Si_(2) is evaluated.