Influence of introducing Zr,Ti,Nb and Ce elements on externally solidified crystals and mechanical properties of high-pressure die-casting Al–Si alloy

High pressure die casting(HPDC)AlSi10Mn Mg alloy castings are widely used in the automobile industry.Mg can optimize the mechanical properties of castings through heat treatment,while the release of thermal stress arouses the deformation of large integrated die-castings.Herein,the development of non-heat treatment Al alloys is becoming the hot topic.In addition,HPDC contains externally solidified crystals(ESCs),which are detrimental to the mechanical properties of castings.To achieve high strength and toughness of non-heat treatment die-casting Al-Si alloy,we used AlSi9Mn alloy as matrix with the introduction of Zr,Ti,Nb,and Ce.Their influences on ESCs and mechanical properties were systematically investigated through three-dimensional reconstruction and thermodynamic simulation.Our results reveal that the addition of Ti increased ESCs'size and porosity,while the introduction of Nb refined ESCs and decreased porosity.Meanwhile,large-sized Al_3(Zr,Ti)phases formed and degraded the mechanical properties.Subsequent introduction of Ce resulted in the poisoning effect and reduced mechanical properties.

Effects of ultrasound on the desulfurization performance of hot coal gas over Zn-Mn-Cu supported on semi-coke sorbent prepared by high-pressure impregnation method

Zn-Mn-Cu/SC（U） sorbent was hydrothermally synthesized by ultrasound-assisted high-pressure impregnation method with semi-coke（SC）as support and the mixed solution of zinc nitrate,manganese nitrate and copper nitrate as active component precursors.The desulfurization performances of hot coal gas on the prepared sorbent at a mid-temperature of 500°C were tested in fixed-bed reactor.Morphology and pore structure of the prepared sorbent were also characterized by TEM,N2adsorption/desorption isotherms and XRD.For comparison,the sorbent of Zn-Mn-Cu/SC prepared by conventional high-pressure impregnation was also evaluated and characterized in order to study the effects of ultrasound treatment.Zn-Mn-Cu/SC（U） sorbent prepared by high-pressure impregnation under ultrasound-assisted condition showed a better desulfurization performance than Zn-Mn-Cu/SC.It could remove H2 S from 1000×10-6m3/m3 to 0.1×10-6m3/m3 at 500°C and maintained for 12.5 h with the sulfur capacity of 7.74%,in which both the breakthrough time and sulfur capacity were about 32% and 51% higher than those of Zn-Mn-Cu/SC sorbent.The introduction of ultrasound during high-pressure impregnation process greatly improved the morphology and pore structure of the sorbent.The ultrasonic treatment made particle size of active components smaller and made them more evenly disperse on semi-coke support,which provided more opportunities to contact with H2S in coal-based gases.However,there were no any difference in compositions and existing forms of active components on the Zn-Mn-Cu/SC and Zn-Mn-Cu/SC（U） sorbents.

Nano-scale Reinforcements and Properties of Al-Si-Cu Alloy Processed by High-Pressure Torsion

To improve the comprehensive mechanical properties of Al-Si-Cu alloy,it was treated by a high-pressure torsion process,and the effect of the deformation degree on the microstructure and properties of the Al-Si-Cu alloy was studied.The results show that the reinforcements(β-Si andθ-CuAl_(2)phases)of the Al-Si-Cu alloy are dispersed in theα-Al matrix phase with finer phase size after the treatment.The processed samples exhibit grain sizes in the submicron or even nanometer range,which effectively improves the mechanical properties of the material.The hardness and strength of the deformed alloy are both significantly raised to 268 HV and 390.04 MPa by 10 turns HPT process,and the fracture morphology shows that the material gradually transits from brittle to plastic before and after deformation.The elements interdiffusion at the interface between the phases has also been effectively enhanced.In addition,it is found that the severe plastic deformation at room temperature induces a ternary eutectic reaction,resulting in the formation of ternary Al+Si+CuAl_(2)eutectic.

Experimental and Finite Element Analysis of Corroded High-Pressure Pipeline Repaired by Laminated Composite

Repairs of corroded high-pressure pipelines are essential for fluids transportation under high pressure.One of the methods used in their repairs is the use of layered composites.The composite used must have the necessary strength.Therefore,the experiments and analytical solutions presented in this paper are performed according to the relevant standards and codes,including ASME PCC-2,ASME B31.8S,ASME B31.4,ISO 24817 and ASME B31.G.In addition,the experimental tests are replicated numerically using the finite element method.Setting the strain gauges at different distances from the defect location,can reduce the nonlinear effects,deformation,and fluctuations due to the high pressure.The direct relationship between the depth of an axial defect and the stress concentration is observed at the inner side edges of the defect.Composite reparation reduces the non-linearities related to the sharp variation of the geometry and a more reliable numerical simulation could be performed.

A Molecular Description of Superconductivity of Sulfur Hydride and Related Systems under High-Pressure Conditions

It has been shown that the recently discovered sulfur trihydride (H3S) can be considered as a superconductor with a transition temperature Tc of 203 Kelvin (K) at 155 GigaPascals (GPa). This is the highest Tc value reported for any superconductor. The established superconductivity occurs via the formation of a molecular system with sulfur atoms arranged on a body-centered cubic lattice. It has been generally accepted that the high Tc value is the result of an efficient electron-phonon interaction. The responsible substance formed by H2S under high pressure, may be considered as a compound with H3S stoichiometry creating an impressive network with hydrogens. We will focus on the hydrogen bonding between sulfur and hydrogens demonstrating a symmetrical arrangement. The geometry of the individual radical compound in relation to corresponding systems will be discussed. Ab initio calculations based on a linear three-center two-, three- and four-electron type of bonding clearly visualized in combination with the dynamics of the Van’t Hoff concept, as described by us in various papers, give a good description of this exclusive network. We also discuss the superconductivity of related phosphorus hydrides and focus on the stability and geometrical differences with respect to the H3S system. These differences are significant, demonstrating the diversity in various structures in showing superconductivity.

Sulfurization synthesis and photocatalytic activity of oxysulfide La_3NbS_2O_5

The oxysulfide La3NbS2O5 was synthesized by sulfurization using H2S and characterized by X-ray diffraction （XRD）, UV-Vis diffuse reflectance spectroscopy （DRS） and field emission scanning electron microscopy （FE-SEM）. The relationship between the sulfurization conditions and the photocatalytic activities for H2 evolution was investigated. Sulfurization method allowed for synthesis of La3NbS2O5 at much lower temperatures and significantly shortened reaction time of 1 h compared with conventional solid-state techniques. The particle morphologies were regular platelike with sizes of 0.1-0.6μm and smooth surfaces. The highest activity for H2 evolution was obtained at 1073 K for 1 h, which was about 1.83 times that of La3NbS2O5 prepared by solid-state method.

Effects of electrolyte recycling on desulfurization from bauxite water slurry electrolysis

To lower the cost of bauxite electrolysis desulfurization using NaOH solution as the supporting electrolyte, effects of electrolyte recycling on bauxite electrolysis desulfurization were investigated. The results indicate that electrode corrosion, cell voltage, the desulfurization rate and the pH value of the electrolyte have no obvious changes with the increase of cycle times. Additionally, there were some transitive valence S-containing ions in electrolyte after the electrolysis, such as SO3^2-,S2O3^2- . However, most of the sulfur in bauxite was eventually oxidized into SO4^2- into the electrolyte, and these S-containing ions did not affect the recycling utilization for electrolyte.

Preparation of Terbium Sesquisulfide and Holmium Sesquisulfide by Sulfurization of Their Oxide Powders Using CS_2 Gas

The formation behaviors of terbium sesquisulfide(Tb_2S_3)and holmium sesquisulfide(Ho_2S_3)synthesized via the sulfurization of their oxide powders using CS_2 gas in the range of temperature 673 to 1323 K were investigated. In the sulfurization of Tb_4O_7 powder, Tb_2O_3 and Tb_2O_2S were formed in the initial stage of reaction, and α-Tb_2S_3 was finally formed at higher temperature. For long sulfurization time of 8 h, single-phase α-Tb_2S_3 could be synthesized at 1323 K. In the sulfurization of Ho_2O_3 powder using CS_2 gas, only Ho_2O_2S was formed as an intermediate product. At a sulfurization temperature above 873 K, Ho_2O_2S was formed in the initial stage of reaction, and single-phase δ-Ho_2S_3 was formed at 1323 K for 8 h instead of Ho_2O_2S. Furthermore, the influence of the addition of carbon black to the sulfurization of Ho_2O_3 powder using CS_2 gas was investigated, and the result implied that the reactions were accelerated slightly by the addition of carbon black.

Effects of Instantaneous High-pressure on Denaturalization of β-Lactoglobulin

[ Objective] The study aimed to explore the denaturalization law of β-Iactoglobulin （β-LG） under instantaneous high-pressure（IHP） con- dition. [Methed] Using fresh milk as testing material, effects of pressure, feed temperature and treatment time on the denaturalization of β-LG were studied via SDS-PAGE electrophoresis and sulfhydryl content detection after IHP treatment. [ Result] IHP could induce the agglomeration and depo- lymerization Of β-LG. The agglomeration of the β-LG increased with the elevated pressure from 20 to 60 MPa, but 80 MPa pressure led to depolyme- rization. The effect of feed temperature （25 -45 ℃） was similar to that of the pressure, while the influence of treatment time （2 -8 min） was not obvious. [ Conclusion] The study provided a theoretical basis for the elimination of allergens in β-LG and the application of IHP technology in milk treatment.

Tectonic Evolution of an Early Precambrian High-Pressure Granulite Belt in the North China Craton

A large-scale high-pressure granulite belt (HPGB), more than 700 km long, is recognized within the metamorphic basement of the North China craton. In the regional tectonic framework, the Hengshan-Chengde HPGB is located in the central collision belt between the western block and eastern block, and represents the deep crustal structural level. The typical high-pressure granulite (HPG) outcrops are distributed in the Hengshan and Chengde areas. HPGs commonly occur as mafic xenoliths within ductile shear zones, and underwent multipile deformations. To the south, the Hengshan-Chengde HPGB is juxtaposed with the Wutai greenstone belt by several strike-slip shear zones. Preliminary isotopic age dating indicates that HPGs from North China were mainly generated at the end of the Neoarchaean, assocaited with tectonic assembly of the western and eastern blocks.

Effect of high-pressure homogenization on stability of emulsions containing zein and pectin

The aim of this study was to investigate the effect of high-pressure homogenization on the droplet size and physical stability of different formulations of pectin–zein stabilized rice bran oil emulsions. The obtained emulsions, both before and after passing through highpressure homogenizer, were subjected to stability test under environmental stress conditions,that is, temperature cycling at 4 °C/40 °C for 6 cycles and centrifugal test at 3000 rpm for 10 min. Applying high-pressure homogenization after mechanical homogenization caused only a small additional decrease in emulsion droplet size. The droplet size of emulsions was influenced by the type of pectin used;emulsions using high methoxy pectin(HMP) were smaller than that using low methoxy pectin(LMP). This is due to a greater emulsifying property of HMP than LMP. The emulsions stabilized by HMP–zein showed good physical stability with lower percent creaming index than those using LMP, both before and after passing through high-pressure homogenizer. The stability of emulsions after passing through high-pressure homogenizer was slightly higher when using higher zein concentration, resulting from stronger pectin–zein complexes that could rearrange and adsorb onto the emulsion droplets.

The Experimental Study of Iron Sulfide Mineral Evolution Under Thermal Sulfurization Condition

Iron sulfide minerals are widely distributed, of which characteristics had the identification significance of formation environment. Previously, there were more research on iron sulfide minerals under hydrothermal condition, and few studies under volcanism formation condition. To simulate volcanic mineralization, the study of different temperature from 250 to 410℃ , different iron sulfur ratio from Fe:S=2∶1 to 1∶8, and two different sources of iron, reduced iron powder (Fe) and ferrous sulfide (FeS), on iron sulfide mineral evolution was investigated under thermal sulfurization condition. By using scanning electron microscopy (SEM), X-ray diffraction (XRD) and other methods, the morphology, composition and structural characteristics of the products were observed and analyzed.

A study of hydrate plug formation in a subsea natural gas pipeline using a novel high-pressure flow loop

The natural gas pipeline from Platform QKI8-1 in the southwest of Bohai Bay to the onshore processing facility is a subsea wet gas pipeline exposed to high pressure and low temperature for a long distance. Blockages in the pipeline occur occasionally. To maintain the natural gas flow in the pipeline, we proposed a method for analyzing blockages and ascribed them to the hydrate formation and agglomeration. A new high-pressure flow loop was developed to investigate hydrate plug formation and hydrate particle size, using a mixture of diesel oil, water, and natural gas as experimental fluids. The influences of pressure and initial flow rate were also studied. Experimental results indicated that when the flow rate was below 850 kg/h, gas hydrates would form and then plug the pipeline, even at a low water content （10%） of a water/oil emulsion. Furthermore, some practical suggestions were made for daily management of the subsea pipeline.

Protolith ages and timing of peak and retrograde metamorphism of the high-pressure granulites in the Shandong Peninsula,eastern North China Craton

High-pressure （HP） granulites widely occur as enclaves within tonalite-trondhjemite- granodiorite （TTG） gneisses of the Early Precambrian metamorphic basement in the Shandong Peninsula, southeast part of the North China Craton （NCC）. Based on cathodoluminescence （CL）, laser Raman spec- troscopy and in-situ U-Pb dating, we characterize the zircons from the HP granulites and group them into three main types： inherited （magmatic） zircon, HP metamorphic zircon and retrograde zircon. The inher- ited zircons with clear or weakly defined magmatic zoning contain inclusions of apatites, and 207pb/206pb ages of 2915--2890 Ma and 2763--2510 Ma, correlating with two magmatic events in the Archaean base- ment. The homogeneous HP metamorphic zircons contain index minerals of high-pressure metamor- phism including garnet, clinopyroxene, plagioclase, quartz, rutile and apatite, and yield 207pb/2066pb ages between 1900 and 1850 Ma, marking the timing of peak HP granulite facies metamorphism. The retrograde zircons contain inclusions of orthopyroxene, plagioclase, quartz, apatite and amphibole, and yield the youngest 207pb/206pb ages of 1840-1820 Ma among the three groups, which we correlate to the medium to low-pressure granulite facies retrograde metamorphism. The data presented in this study suggest subduction of Meso- and Neoarchean magmatic protoliths to lower crust depths where they were subjected to HP granulite facies metamorphism during Palaeoproterozoic （1900-1850 Ma）. Subse- quently, the HP granulites were exhumated to upper crust levels, and were ovel-printed by medium to low-pressure granulite and amphibolite facies retrograde event at ca. 1840--820 Ma.

Growth of covellite crystal onto azurite surface during sulfurization and its response to flotation behavior

In this work,the growth of copper sulfide crystal onto azurite surfaces during sulfurization and its response to flotation are investigated.Filed emission scanning electron microscopy-energy dispersive X-ray spectroscopy(FESEM) and X-ray diffraction(XRD) studies confirmed that the sulfurization of azurite is not limited to the mineral surface,but rather penetrates into the bulk to form covellite crystal(synCuS),creating favorable conditions for the stable adsorption of xanthate and greatly promoting the azurite flotation.Additionally,as demonstrated by X-ray photoelectron spectroscopy(XPS) and time of flight secondary ion mass spectrometry(TOF-SIMS) analyses,a redox reaction occurred during this process,and Cu(Ⅱ) onto the mineral surface was reduced to Cu(Ⅰ).Correspondingly,reduced S^(2-) was oxidized to(S_(2))^(2-),(S_n)^(-2),and even to deeper oxidation state S~0,(S_(x)O_(y))^(n-) and SO_(4)^(2-).Excess sodium sulfide strengthens copper sulfide to form onto the azurite surface,and provides enough raw material for crystal copper sulfide to grow,resulting in the formation of "flake-like" covellite with a better crystallinity.However,the floatability of azurite decreased dramatically under this condition,because the generated massive colloidal copper sulfide in flotation pulp deteriorates the flotation environment,resulting in a decreased effective adsorption of collector onto azurite surfaces.

Oxidative desulfurization of diesel fuel with caprolactam-based acidic deep eutectic solvents: Tailoring the reactivity of DESs by adjusting the composition

Despite the significance of hydrogen bonding in deep eutectic solvents（DESs） for desulfurization processes, little is understood about the relationship between the DES composition, hydrogen-bonding strength, and oxidative desulfurization activity. In this study, a new family of caprolactam-based acidic DESs was prepared with different molar ratios of caprolactam and oxalic acid. The prepared DESs were characterized by differential scanning calorimetry, Fourier transform infrared spectroscopy, 1 H nuclear magnetic resonance, and thermogravimetric analyses. These DESs were employed for oxidative desulfurization reactions and the desulfurization efficiency was found to vary regularly with the DES composition. The factors influencing the removal of dibenzothiophene were systematically investigated and the desulfurization efficiency of the caprolactam-based acidic DESs reached as high as 98% under optimal conditions. The removal of different sulfur compounds followed the order： dibenzothiophene 4,6-dimethyldibenzothiophene benzothiophene. The combined experimental data and characterization results revealed that the oxidative desulfurization efficiency of the system was influenced by the hydrogen bonding interactions with the DES, which can be optimized by adjusting the DES composition. These findings regarding hydrogen bonding in DESs provide new insight for better understanding of the mechanism of diesel deep desulfurization processes.

Impact of impregnation pressure on desulfurization performance of Zn-based sorbents supported on semi-coke

High-pressure impregnation, a new preparation method for sorbents to remove H2S from hot coal gas, is introduced in this paper. Semi-coke （SC） and ZnO is selected as the support and active component of sorbent, respectively. The sorbent preparation process includes high-pressure impregnation, filtration, ovendry and calcination. The aim of this research is to primarily study the effects of the impregnation pressure on physical properties and desulfurization ability of the sorbent. The desulfurization experiment was carried out in a fixed-bed reactor at 500 ~C and a simulated coal gas used in this work was composed of CO （33 vol%）, H2 （39 vol%）, H2S （300 ppm in volume）, and N2 （balance）. Experimental results show that the pore structure of the SC support can be improved effectively and ZnO active component can be uniformly dispersed on the support, with the small particle size of 10-500 nm. Sorbents prepared using high-pressure impregnation have better desulfurization capacity and their active components have higher utilization rate. P20-ZnSC sorbent, obtained by high-pressure impregnation at 20 atm, has the best desulfurization ability with a sulfur capacity of 7.54 g S/100g sorbent and a breakthrough time of 44 h. Its desulfurization precision and efficiency of removing H2S from the middle temperature gases can reach 〈 1 ppm and 〉99.7%, respectively, before sorbent breakthrough.

Mechanisms and capacity of high-pressure soaking after hydraulic fracturing in tight/shale oil reservoirs

Huff-n-puff by water has been conducted to enhance oil recovery after hydraulic fracturing in tight/shale oil reservoirs.However,the mechanisms and capacity are still unclear,which significantly limits the application of this technique.In order to figure out the mechanisms,the whole process of pressurizing,high-pressure soaking,and depressurizing was firstly discussed,and a mechanistic model was established.Subsequently,the simulation model was verified and employed to investigate the significances of high-pressure soaking,the contributions of different mechanisms,and the sensitivity analysis in different scenarios.The results show that high-pressure soaking plays an essential role in oil production by both imbibition and elasticity after hydraulic fracturing.The contribution of imbibition increases as the increase in bottom hole pressure(BHP),interfacial tension,and specific surface area,but slightly decreases as the oil viscosity increases.In addition,it first decreases and then slightly increases with the increase in matrix permeability.The optimal soaking time is linear with the increases of both oil viscosity and BHP and logarithmically declines with the increase in matrix permeability and specific surface area.Moreover,it shows a rising tendency as the interficial tension(IFT)increases.Overall,a general model was achieved to calculate the optimal soaking time.

Gas Film Disturbance Characteristics Analysis of High-Speed and High-Pressure Dry Gas Seal

The dry gas seal（DGS） has been widely used in high parameters centrifugal compressor, but the intense vibrations of shafting, especially in high-speed condition, usually result in DGS＇s failure. So the DGS＇s ability of resisting outside interference has become a determining factor of the further development of centrifugal compressor. However, the systematic researches of which about gas film disturbance characteristics of high parameters DGS are very little. In order to study gas film disturbance characteristics of high-speed and high-pressure spiral groove dry gas seal（S-DGS） with a flexibly mounted stator, rotor axial runout and misalignment are taken into consideration, and the finite difference method and analytical method are used to analyze the influence of gas film thickness disturbance on sealing performance parameters, what＇s more, the effects of many key factors on gas film thickness disturbance are systematically investigated. The results show that, when sealed pressure is 10.1MPa and seal face average linear velocity is 107.3 m/s, gas film thickness disturbance has a significant effect on leakage rate, but has relatively litter effect on open force; Excessively large excitation amplitude or excessively high excitation frequency can lead to severe gas film thickness disturbance; And it is beneficial to assure a smaller gas film thickness disturbance when the stator material density is between 3.1 g/cm3 to 8.4 g/cm3; Ensuring sealing performance while minimizing support axial stiffness and support axial damping can help to improve dynamic tracking property of dry gas seal. The proposed research provides the instruction to optimize dynamic tracking property of the DGS.

Research progress on desulfurization technology of high-sulfur bauxite

Bauxite is the main raw material of the alumina industry.However,high-sulfur bauxite constitutes a relatively large proportion of bauxite resource in China.Excessive sulfur impurities in bauxite have significant impact on the Bayer process,such as corrosion of equipment and pipelines,increased consumption of alkali,and difficulties in sedimentation of red mud particles after digestion.As the mainstreams of bauxite desulfurization technologies,the bauxite pre-desulfurization(roasting,electrochemistry,biology,flotation,etc)and Bayer process desulfurization(oxidation and precipitation)need to be fully understood for the further improvement of desulfurization performance.Here,an in-depth review on their mechanisms and advantages/disadvantages is presented.