A Novel Fracturing Fluid with High-Temperature Resistance for Ultra-Deep Reservoirs

Ultra-deep reservoirs play an important role at present in fossil energy exploitation.Due to the related high temperature,high pressure,and high formation fracture pressure,however,methods for oil well stimulation do not produce satisfactory results when conventional fracturing fluids with a low pumping rate are used.In response to the above problem,a fracturing fluid with a density of 1.2~1.4 g/cm^(3)was developed by using Potassium formatted,hydroxypropyl guanidine gum and zirconium crosslinking agents.The fracturing fluid was tested and its ability to maintain a viscosity of 100 mPa.s over more than 60 min was verified under a shear rate of 1701/s and at a temperature of 175℃.This fluid has good sand-carrying performances,a low viscosity after breaking the rubber,and the residue content is less than 200 mg/L.Compared with ordinary reconstruction fluid,it can increase the density by 30%~40%and reduce the wellhead pressure of 8000 m level reconstruction wells.Moreover,the new fracturing fluid can significantly mitigate safety risks.

Research Progress of Additives to Improve Hydration Resistance of Magnesia-calcium Materials

Magnesia-calcium materials have stable hot performance,good resistance to the erosion and corrosion of liquid steel and steel slag,and a special role in purifying liquid steel,so they are widely used in iron and steel industry.However,hydration of magnesia-calcium materials seriously restricts their use,so researches have been done to improve their hydration resistance,obtaining a series of achievements.In this paper,the improvements on the hydration resistance of magnesia-calcium materials by additives in recent 20 years were presented,and their mechanisms were summarized.

A high-temperature resistant and high-density polymeric saturated brine-based drilling fluid

Three high-temperature resistant polymeric additives for water-based drilling fluids are designed and developed:weakly cross-linked zwitterionic polymer fluid loss reducer(WCZ),flexible polymer microsphere nano-plugging agent(FPM)and comb-structure polymeric lubricant(CSP).A high-temperature resistant and high-density polymeric saturated brine-based drilling fluid was developed for deep drilling.The WCZ has a good anti-polyelectrolyte effect and exhibits the API fluid loss less than 8 mL after aging in saturated salt environment at 200°C.The FPM can reduce the fluid loss by improving the quality of the mud cake and has a good plugging effect on nano-scale pores/fractures.The CSP,with a weight average molecular weight of 4804,has multiple polar adsorption sites and exhibits excellent lubricating performance under high temperature and high salt conditions.The developed drilling fluid system with a density of 2.0 g/cm^(3)has good rheological properties.It shows a fluid loss less than 15 mL at 200°C and high pressure,a sedimentation factor(SF)smaller than 0.52 after standing at high temperature for 5 d,and a rolling recovery of hydratable drill cuttings similar to oil-based drilling fluid.Besides,it has good plugging and lubricating performance.

Copper-Free Resin-Based Braking Materials:A New Approach for Substituting Copper with Fly-Ash Cenospheres in Composites

Copper particles emitted from braking have become a significant source of environmental pollution.However,copper plays a crucial role in resin-based braking materials.Developing high-performance braking materials without copper has become a significant challenge.In this paper,the resin-based braking materials were filled with flyash cenospheres to develop copper-free braking materials.The effects of fly-ash cenospheres on the physical properties,mechanical and friction and wear properties of braking materials were studied.Furthermore,the wear mechanism of copper-free resin-based braking materials filled with fly-ash cenospheres was discussed.The results indicate that the inclusion of fly-ash cenospheres in the braking materials improved their thermal stability,hardness and impact strength,reduced their density,effectively increased the friction coefficient at medium and high temperatures,and enhanced the heat-fade resistance of the braking materials.The inclusion of fly-ash cenospheres contributed to the formation of surface friction film during the friction process of the braking materials,and facilitated the transition of form from abrasive wear to adhesive wear.At 100-350℃,the friction coefficient of the optimal formulation is in the range of 0.57-0.61,and the wear rate is in the range(0.29-0.65)×10^(-7) cm^(3)·N^(-1)·m^(-1),demonstrating excellent resistance to heat-fade and stability in friction coefficient.This research proposes the use of fly-ash cenospheres as a substitute for environmentally harmful and expensive copper in brake materials,which not only improves the performance of braking materials but also reduces their costs.

Strength Acquisition Mechanism of High Temperature Resistant Materials Prepared by Waste Architectural Ceramics

In order to realize the large-scale and high-value utilization of waste architectural ceramics,high-temperature resistant materials based on waste architectural ceramics were prepared with sodium silicate as the binder,clay/bauxite and metakaolin/bauxite as coating materials,and the cold strength obtaining mechanism was explored.The phase composition,the microstructure and the mechanical properties of the high temperature resistant materials based on waste architectural ceramics were tested and analyzed.The results showed that when the heat treatment temperature was between 110-1000℃,the strength of the samples mainly came from the physical adhesion of sodium silicate and fine powder.When the temperature rose to 1100℃,the strength of the sample was improved since the internal low-melting-point components melted and promoted sintering.The addition of clay and bauxite can effectively enhance the flexural strength of the samples when the heat treatment temperature is 1000℃.When the heat treatment temperature rises from 900 to 1000℃,the flexural strength of the samples will be enhanced owing to the formation of silica alumina spinel and mullite from metakaolin.

Flexural behavior of composite beams after the ultimate limit state externally strengthened with CFRP sheets bonded with high-temperature resistant matrix

In this paper the alkali-activated slag cementitious materials(AASCM)which strength at 600 ℃ is larger than that of AASCM at room temperature,were prepared to paste CFRP sheets to strengthen four simply supported unbonded prestressed composite beams encased circular steel tube truss after ultimate limit state.Test on flexural behavior of these four beams was performed.Moreover,normal section load-bearing capacity of these beams and the curve load-deflection at mid-span were obtained.Experimental results show that it is feasible to strengthen concrete members with CFRP sheets bonded with AASCM.Based on the experimental results and theoretical study,computational method of stiffness is proposed for calculating bending rigidity and normal section load-bearing capacity of concrete simply supported beams strengthened with CFRP sheets bonded with AASCM.Formula of bending rigidity calculation was founded which results are in good agreement with testing data.

Effect of Rare Earths on Microstructure and Properties of TiC-based Cermet/Cu Alloy Composite Wear Resistant Materials

The effect of rare earth (RE) oxide on the microstructure and properties of TiC based cermet/Cu alloy composite hardfacing materials was investigated by using scanning electron microscope (SEM), transmission electron microscope (TEM), impact test and wear test. The mechanism of RE oxide for improving the phase structure and the impact toughness was also discussed. The experimental results indicate that the microstructure of the matrix can be refined, and the micro-porous defects can be eliminated by adding RE oxide into the composite materials. The polycrystalline and amorphous phase structure is formed at the interface of cermet and matrix metal. The formed structure enhances the conjoint strength of interface. The frictional wear resistance can be improved obviously, although the microhardness of the matrix metal can not be effectively increased by adding RE oxide.

New Developments in the Calorimetry of High-Temperature Materials

1. Introduction Thermodynamics forms the fundamental underpinning of reactivity, transformation, and stability, and controls processes such as synthesis, corrosion and degradation, environmental transport, catalysis, and biological reactivity. In the materials field, the wealth of new compounds, polymorphs, hybrid organic–inorganic hybrid materials and metal organic frameworks, high-entropy alloys, and multiphase and nanophase materials attained by a variety of non-equilibrium synthesis and processing methodologies has outrun the available thermodynamic data, hampering current understanding of synthetic pathways, materials compatibility, and longevity during use, degradation, corrosion, and dissolution, and limiting our understanding of environmental contamination and transport for new materials.

Micro-analysis of high-temperature oxidation-resistance of a new kind of heat-resistant grid plate in grate-kiln

To further improve the oxidation-resistance of materials and reduce the cost of grid plates in grate-kiln, a new kind of heat-resistant grid plate was developed. The microstructure of this grid plate with a life more than 18 months was studied by XRD, SEM and EDS techniques. The results show that high hardness, high intensity and good impact property make the new kind of heat-resistant grid plate and its oxide film have a higher resistance to deformation and abrasion at 900-1000℃ Besides, small grain size is beneficial to form a complete protective oxide film. The oxide film composed of SiO2 layer, Cr2O3 layer and Fe2O3 layer is rather thin and bonds closely with the backing. The forming of the chemical stable nickel-rich layer increases the density of Cr2O3 layer.

High-temperature oxidation behavior of heat resistant stainless steel 1.4828

The kinetic curves of the high-temperature oxidation of austenitic heat resistant stainless steel 1. 4828 at 1 050 ℃ were measured using a weighing method. It is shown that the oxidation curves at 1 050 ℃ followed the parabolic line law, and after 250 h of oxidation, the mass gain was about 80 g/m2. The surface morphology and structure of the oxide layers were studied by scanning electron microscopy and X-ray diffraction. A complicated oxide layer obtained at 1 050 ℃ was mainly composed, from inner to outer, of （FeSi） 3 04, Cr2 03, Fe2 03, and spinel oxides FeCr204 and NiMn204.

National Joint Engineering Research Center of High Performance Metal Wear Resistant Materials Technology

Founded in 2012, the National Joint Engineering Research Center of High Performance Metal Wear Resistant Materials Technology at Jinan University, one of the"211"key national universities in China, specializes in the research and development of iron based wear resistant materials and their casting technologies to provide support to the production process.

National Joint Engineering Research Center of High Performance Metal Wear Resistant Materials Technology

Founded in 2012,the National Joint Engineering Research Center of High Performance Metal Wear Resistant Materials Technology at Jinan University,one of the'211'key national universities in China,specializes in the research and development of iron based wear resistant materials and their casting technologies to provide support to the production process.The Research Center serves the'Guangdong Province Ceeusro Innovation Platform for Common Technology of High Performance Wear Resistant Materials”,“Guangdong Province Engineering Research Center for Wear Resistant and Special Functional Materials”.

Abrasion Resistant Refractory Materials

1 Scope This standard specifies the definition, classification, technical requirements, test methods, quality appraisal procedure, packing, marking, transportation, storage, and quality certificate of abrasion resistant refractory materials.

A Rapid Identification Method for Germplasm Materials Resistant to Citrus Huanglongbing Disease

[Objectives]This study was conducted to develop a rapid identification method for citrus germline materials resistant to Huanglongbing disease and lay a basis for accelerating citrus breeding for resistance to Huanglongbing and increasing the breeding efficiency.[Methods]Thirty-six citrus germplasms suspected to be resistant to citrus Huanglongbing disease were collected.The method of direct high grafting to citrus trees infected with Huanglongbing pathogen was adopted.The resistance of the test materials was identified and evaluated by field symptoms combined with quantitative PCR.It was defined as the top grafting identification method.[Results]The test materials that were grafted in spring started to germinate after one month,and three months late(June 5,2018)typical mottled yellowing on leaves was observed on KH-14 for the first time.After four months(July 5,2018)of top grafting,typical mottled yellowing occurred on 23 materials,and 11 materials showed no such symptom.After six months(September 4,2018)of top grafting,although the growth of KH-18,KH-12,KHY-4,KHY-5 and KHY-6 were normal,yellowing was observed on their leaves.Only KH-21 grew well,and showed no yellow shoots and yellowing leaves.It was identified as the material with resistance to Huanglongbing disease.Quantitative PCR tests on the above six materials showed that KH-21 was negative and other five were positive.Real-time fluorescence quantitative PCR test indicated that the average Huanglongbing bacteria amount in KH-21 was 1870.0 cell/μg DNA,and the average Huanglongbing bacteria amount in the control material was 372285.5 cell/μg DNA,indicating KH-21 was resistant to Huanglongbing bacteria.[Conclusions]The method for infecting bacteria by top grafting takes six months,can detect large amount of seedlings,and is time-saving,efficient,cost-saving and accurate.This method can quickly identify the resistance of citrus varieties to citrus Huanglongbing disease,and can be popularized and used in the identification of citrus Huanglongbing disease resistance.

DIFFUSION COUPLE BETWEEN HIGHSTRENGTH WEAR-RESISTING ALUMINUM BRONZE AND MACHINING TOOLS MATERIALS

ＩＮＴＲＯＤＵＣＴＩＯＮＡｌｕｍｉｎｕｍｂｒｏｎｚｅｉｓａｎｉｍｐｏｒｔａｎｔｅｎｇｉｎｅｅｒｉｎｇｍａｔｅｒｉａｌ．Ｉｔｓｅｘｃｅｌｅｎｔｐｈｙｓｉｃａｌ，ｍｅｃｈａｎｉｃａｌ，ａｎｔｉｃｏｒｏｓｉｏｎａｎｄｗｅａｒｒｅｓｉｓｔｉｎｇｐｒｏｐ...

Application of New Heavy Metals Resistant Porous Binder Material Used in Fluid Catalytic Cracking Reaction

A novel porous binder was obtained from acid-treated kaolin. This new binder possessed abundant meso/macropores, good hydrothermal stability and heavy metal resistance. The prepared catalyst using new binder featured low attrition index and large pore volume. The catalysts were contaminated with Ni, V, and tested in a fixed-fluidized bed reactor unit. In comparison with the reference sample, the oil conversion achieved by the above-mentioned catalyst increased by 3.50 percentage points, and heavy oil yield decreased by 2.86 percentage points, while the total liquid yield and light oil yield increased by 2.82 percentage points and 0.79 percentage points, respectively. The perfect pore structure, good hydrothermal stability and heavy metal resistant performance of new binder were the possible causes leading to its outstanding performance.

High-temperature Resistance Performance of An Inorganic Adhesive for Concrete Structures Strengthened with CFRP Sheets

Organic epoxy matrices have been widely used in the FRP reinforcing technique, but they have serious disadvantages of poor high-temperature resistance. An inorganic adhesive is invented to replace the organic adhesive. For the inorganic adhesive at normal temperature and different high temperatures, the microstructure and phase composition are investigated by means of X-ray diffraction （XRD） and SEM respectively. Results show that inorganic adhesive can resist at least 600 ℃ high temperature. Fire-resistance performance of inorganic adhesive can meet the requirements of fiber reinforced polymer （FRP） strengthened RC structures.

Combustion Characteristics of Solid Sustained-Release Energetic Materials

A solid sustained-release energetic material sample,an eruption device and a complete test system were prepared further to analyse the combustion characteristics of solid sustainedrelease energetic materials.The high-temperature heat flux generated by the combustion of the samples from the eruption device was used to penetrate the Q235 target plate.In addition,the meaning and calculation formula of energy density characterising the all-around performance of heat flux were proposed.The numerical simulation of the combustion effect of samples was carried out.According to the data comparison,the numerical simulation results agreed with the experimental results,and the maximum deviation between the two was less than 8.9%.In addition,the structure of the combustion wave and high-temperature jet was proposed and analysed.Based on theoretical analysis,experimental research and numerical simulation,the theoretical burning rate formula of the sample was established.The maximum error between the theoretically calculated mass burning rate and the experimental results was less than 9.8%.Therefore,using the gas-phase steady-state combustion model to study the combustion characteristics of solid sustained-release energetic materials was reasonable.The theoretical burning rate formula also had high accuracy.Therefore,the model could provide scientific and academic guidance for the theoretical research,system design and practical application of solid sustained-release energetic materials in related fields.

Different variation behaviors of resistivity for high-temperature-grown and low-temperature-grown p-GaN films

Two series of p-GaN films grown at different temperatures are obtained by metal organic chemical vapor deposition（MOCVD）. And the different variation behaviors of resistivity with growth condition for high- temperature（HT）-grown and low-temperature（LT）-grown p-GaN films are investigated. It is found that the resistivity of HT-grown p-GaN film is nearly unchanged when the NH_3 flow rate or reactor pressure increases. However, it decreases largely for LT-grown p-GaN film.These different variations may be attributed to the fact that carbon impurities are easy to incorporate into p-GaN film when the growth temperature is low. It results in a relatively high carbon concentration in LT-grown p-GaN film compared with HT-grown one. Therefore, carbon concentration is more sensitive to the growth condition in these samples, ultimately,leading to the different variation behaviors of resistivity for HT- and LT-grown ones.