Ballistic performances of the hourglass lattice sandwich structures under high-velocity fragments

In this paper,the numerical simulation method is used to study the ballistic performances of hourglass lattice sandwich structures with the same mass under the vertical incidence of fragments.Attention is paid to elucidating the influences of rod cross-section dimensions,structure height,structure layer,and rod inclination angle on the deformation mode,ballistic performances,and ability to change the ballistic direction of fragments.The results show that the ballistic performances of hourglass lattice sandwich structures are mainly affected by their structural parameters.In this respect,structural parameters optimization of the hourglass lattice sandwich structures enable one to effectively improve their ballistic limit velocity and,consequently,ballistic performances.

Comparative investigation of microstructure and high-temperature oxidation resistance of high-velocity oxy-fuel sprayed CoNiCrAlY/nano-Al_(2)O_(3) composite coatings using satellited powders

Satellited CoNiCrAlY–Al_(2)O_(3)feedstocks with 2wt%, 4wt%, and 6wt% oxide nanoparticles and pure CoNiCrAlY powder were deposited by the high-velocity oxy fuel process on an Inconel738 superalloy substrate. The oxidation test was performed at 1050℃ for 5, 50, 100,150, 200, and 400 h. The microstructure and phase composition of powders and coatings were characterized by scanning electron microscopy and X-ray diffraction, respectively. The bonding strength of the coatings was also evaluated. The results proved that with the increase in the percentage of nanoparticles(from 2wt% to 6wt%), the amount of porosity(from 1vol% to 4.7vol%), unmelted particles, and roughness of the coatings(from 4.8 to 8.8 μm) increased, and the bonding strength decreased from 71 to 48 MPa. The thicknesses of the thermally grown oxide layer of pure and composite coatings(2wt%, 4wt%, and 6wt%) after 400 h oxidation were measured as 6.5, 5.5, 7.6, and 8.1 μm, respectively.The CoNiCrAlY–2wt% Al_(2)O_(3)coating showed the highest oxidation resistance due to the diffusion barrier effect of well-dispersed nanoparticles. The CoNiCrAlY–6wt% Al_(2)O_(3)coating had the lowest oxidation resistance due to its rough surface morphology and porous microstructure.

A rotary-shear low to high-velocity friction apparatus in Beijing to study rock friction at plate to seismic slip rates

This paper reviews 19 apparatuses having highvelocity capabilities,describes a rotary-shear low to highvelocity friction apparatus installed at Institute of Geology,China Earthquake Administration,and reports results from velocity-jump tests on Pingxi fault gouge to illustrate technical problems in conducting velocity-stepping tests at high velocities.The apparatus is capable of producing plate to seismic velocities（44 mm/a to 2.1 m/s for specimens of 40 mm in diameter）,using a 22 kW servomotor with a gear/belt system having three velocity ranges.A speed range can be changed by 103 or 106by using five electromagnetic clutches without stopping the motor.Two cam clutches allow fivefold velocity steps,and the motor speed can be increased from zero to 1,500 rpm in 0.1-0.2 s by changing the controlling voltage.A unique feature of the apparatus is a large specimen chamber where different specimen assemblies can be installed easily.In addition to a standard specimen assembly for friction experiments,two pressure vessels were made for pore pressures to 70 MPa;one at room temperature and the other at temperatures to 500 °C.Velocity step tests are needed to see if the framework of rate-and-state friction is applicable or not at high velocities.We report results from velocity jump tests from 1.4 mm/s to 1.4 m/s on yellowish gouge from a Pingxi fault zone,located at the northeastern part of the Longmenshan fault system that caused the 2008 Wenchuan earthquake.An instantaneous increase in friction followed by dramatic slip weakening was observed for the yellowish gouge with smooth sliding surfaces of host rock,but no instantaneous response was recognized for the same gouge with roughened sliding surfaces.Instantaneous and transient frictional properties upon velocity steps cannot be separated easily at high velocities,and technical improvements for velocity step tests are suggested.

High-velocity frictional behavior of Longmenshan fault gouge from Hongkou outcrop and its implications for dynamic weakening of fault during the 2008 Wenchuan earthquake

High-velocity friction experiments were conducted on clayey fault gouge collected from Hongkou outcrop of Beichuan fault, located at the southwestern part of Longmenshan fault system that caused the disastrous 2008 Wenchuan earthquake. The ultimate purpose of this study is to reproduce this earthquake by modeling based on measured frictional properties. Dry gouge of about 1 mm in thickness was deformed dry at slip rates of 0.01 to 1.3 m/s and at normal stresses of 0.61 to 3.04 MPa, using a rotary-shear high-velocity frictional testing machine. The gouge displays slip weakening behavior as initial peak friction decays towards steady-state values after a given displacement. Both peak friction and steady-state friction remain high at slow slip rates are exam- ined and gouge only exhibits dramatic weakening at high slip rates, with steady-state friction coefficient values of about 0.1 to 0.2. Specific fracture energy ranges from 1 to 4 MN/m in our results and this is of the same order as seismically determined values. Low friction coefficients measured on experimental faults are in broad agree- ment with lack of thermal anomaly observed from temperature measurements in WFSD-1 drill hole （Wenchuan Earthquake Fault Scientific Drilling Project）, which can be explained by even smaller friction coefficient for the Wenchuan earthquake fault. High-velocity friction experiments with pore water needs to be done to see if even smaller friction is attained or not. Shiny slickenside surfaces form at high slip rates, but not at slow slip rates. Slip zone with slickenside surface changes its color to dark brown and forms duplex-like microstructures, which are similar to those microstructures found in the fault gouges from the Hongkou outcrop. Detailed comparisons between experimentally deformed gouge samples and WFSD drill cores in the future will reveal how much we could reproduce the dynamic weakening processes in operation in fault zones during Wenchuan earthquake at present.

Internal structures and high-velocity frictional properties of Longmenshan fault zone at Shenxigou activated during the 2008 Wenchuan earthquake

This paper reports internal structures of a wide fault zone at Shenxigou,Dujiangyan,Sichuan province,China,and high-velocity frictional properties of the fault gouge collected near the coseismic slip zone during the 2008 Wenchuan earthquake.Vertical offset and horizontal displacement at the trench site were 2.8 m（NW side up）and 4.8 m（right-lateral）,respectively.The fault zone formed in Triassic sandstone,siltstone,and shale about 500 m away from the Yingxiu-Beichuan fault,a major fault in the Longmenshan fault system.A trench survey across the coseismic fault,and observations of outcrops and drill cores down to a depth of 57 m revealed that the fault zone consists of fault gouge and fault breccia of about0.5 and 250-300 m in widths,respectively,and that the fault strikes N62°E and dips 68° to NW.Quaternary conglomerates were recovered beneath the fault in the drilling,so that the fault moved at least 55 m along the coseismic slip zone,experiencing about 18 events of similar sizes.The fault core is composed of grayish gouge（GG） and blackish gouge（BG） with very complex slip-zone structures.BG contains low-crystalline graphite of about 30 %.High-velocity friction experiments were conducted at normal stresses of 0.6-2.1 MPa and slip rates of 0.1-2.1 m/s.Both GG and BG exhibit dramatic slip weakening at constant high slip rates that can be described as an exponential decay from peak friction coefficient lpto steadystate friction coefficient lssover a slip-weakening distance Dc.Deformation of GG and BG is characterized by overlapped slip-zone structures and development of sharp slickenside surfaces,respectively.Comparison of our data with those reported for other outcrops indicates that the high-velocity frictional properties of the Longmenshan fault zones are quite uniform and the high-velocity weakening must have promoted dynamic rupture propagation during the Wenchuan earthquake.

A novel approach to predict green density by high-velocity compaction based on the materials informatics method

High-velocity compaction is an advanced compaction technique to obtain high-density compacts at a compaction velocity of ≤10 m/s. It was applied to various metallic powders and was verified to achieve a density greater than 7.5 g/cm^3 for the Fe-based powders. The ability to rapidly and accurately predict the green density of compacts is important, especially as an alternative to costly and time-consuming materials design by trial and error. In this paper, we propose a machine-learning approach based on materials informatics to predict the green density of compacts using relevant material descriptors, including chemical composition, powder properties, and compaction energy. We investigated four models using an experimental dataset for appropriate model selection and found the multilayer perceptron model worked well, providing distinguished prediction performance, with a high correlation coefficient and low error values. Applying this model, we predicted the green density of nine materials on the basis of specific processing parameters. The predicted green density agreed very well with the experimental results for each material, with an inaccuracy less than 2%. The prediction accuracy of the developed method was thus confirmed by comparison with experimental results.

Fe-based amorphous coating prepared using high-velocity oxygen fuel and its corrosion behavior in static lead-bismuth eutectic alloy

The Fe_(949.7)Cr_(18)Mn_(1.9)Mo_(7.4)W_(1.6)B_(15.2)C_(3.8)Si_(2) amorphous coating was deposited on T91 steel substrate by using the high-velocity oxygen fuel(HVOF)spray technique to enhance the corrosion resistance of T91 stainless steel in liquid lead-bismuth eutectic(LBE).The corrosion behavior of the T91 steel and coating exposed to oxygen-saturated LBE at 400℃ for 500 h was investigated.Results showed that the T91 substrate was severely corroded and covered by a homogeneously distributed dual-layer oxide on the interface contacted to LBE,consisting of an outer magnetite layer and an inner Fe-Cr spinel layer.Meanwhile,the amorphous coating with a high glass transition temperature(Tg=550℃)and crystallization temperature(T_(x)=600℃)exhibited dramatically enhanced thermal stability and corrosion resistance.No visible LBE penetration was observed,although small amounts of Fe_(3)O_(4),Cr_(2)O_(3),and PbO were found on the coating surface.In addition,the amorphicity and interface bonding of the coating layer remained unchanged after the LBE corrosion.The Fe-based amorphous coating can act as a stable barrier layer in liquid LBE and have great application potential for long-term service in LBE-cooled fast reactors.

Influence of High-Velocity Blood Flow on Right-to-Left Shunt in Patients with Patent Foramen Ovale during the Valsalva Maneuver

In this study, we investigated the changes in the right-to-left shunt (RLS) of the patent foramen ovale (PFO) at different phases of the Valsalva maneuver and analyzed the possible mechanisms. The study population consisted of 57 patients with symptoms highly suggestive of a PFO. These patients had been diagnosed with apsychia, migraine with aura, cerebral infarction, transient ischemic attack (TIA), and cerebral ischemia with unknown cause. Routine echocardiography was performed in all patients to rule out a cardiac malformation. Contrast-transcranial Doppler (c-TCD) and contrast-enhanced transthoracic echocardiography (c-TTE) were used to visualize and quantify the RLS. The standard apical four chamber view was used to observe the changes of E peak, A peak, and velocity-time integral (VTI) ratio of tricuspid blood flow during the strain phase and release phase of the Valsalva maneuver. Paired t-test was used to compare E peak, A peak, and VTI ratio of tricuspid blood flow during the different phases. The right-to-left shunt across the PFO (PFO-RLS) was graded in the two phases and compared by Kruskal-Wallis test. Compared with the strain phase of the Valsalva maneuver, the parameters of E, A, and VTI in diastolic period in patients with PFO-RLS at the release phase were significantly increased [54.30 ± 13.65 cm/s vs 100.35 ± 21.11 cm/s, 42.21 ± 12.32 cm/s vs 57.30 ± 18.88 cm/s, 10.34 ± 3.27 cm/s vs 19.58 ± 4.56 cm/s, respectively], and the difference was statistically significant. The positive consequence of PFO-RLS, as diagnosed by c-TTE with the Valsalva maneuver at the release phase of the Valsalva maneuver, was significantly higher than that at the strain phase of the Valsalva maneuver. At the beginning of release phase of the Valsalva maneuver, decreased intrathoracic pressure led to increased venous backflow into the right atrium. Thus, high-velocity blood flow rapidly pushed the PFO open, which resulted in a significant increase in the PFO-RLS. Therefore, the increase of the PFO-RLS during the Valsalva maneuver is caused by the impact of high-velocity blood flow the PFO.

A three-dimensional Eulerian method for the numerical simulation of high-velocity impact problems

In the present paper, a three-dimensional （3D） Eulerian technique for the 3D numerical simulation of high-velocity impact problems is proposed. In the Eulerian framework, a complete 3D conservation element and solution element scheme for conservative hyperbolic governing equations with source terms is given. A modified ghost fluid method is proposed for the treatment of the boundary conditions. Numerical simulations of the Taylor bar problem and the ricochet phenomenon of a sphere impacting a plate target at an angle of 60~ are carried out. The numerical results are in good agreement with the corresponding experimental observations. It is proved that our computational technique is feasible for analyzing 3D high-velocity impact problems.

High-Velocity Impact Studies on Scaled Leading Edges of Horizontal Tail with Smart Composite Layers

Bird strike studies on typical aluminium leading edges of the Horizontal Tail (HT) with and without Glass Fibre Shape Memory Polymer (GF-SMP) layers are carried out. A one-fifth scaled model of HT is designed and fabricated. The parameters like bird dimension and energy requirements are accordingly scaled to conduct the bird strike tests. Two leading-edge components have been prepared, namely one with AL 2024-T3 aluminium alloy and the other specimen of the same dimension and material, additionally having GF-SMP composite layers inside the metallic leading edge, in order to enhance its impact resistance. Bird strike experiments are performed on both the specimens, impacting at the centre of the leading edge in the nose tip region with an impact velocity of 115 m/s. The test component is instrumented with linear post-yield strain gauges on the top side and the PZT sensors on the bottom. Furthermore, the impact scenario is monitored using a high-speed camera at 7000 fps. The bird strike event is simulated by an equation of state model, in which the mass of the bird is idealized using smooth particle hydrodynamics element in PAMCRASH? explicit solver. The strain magnitude and its pattern including time duration are found to be in a good correlation between test and simulation. Key metrics are evaluated to devise an SHM scheme for the load and impact event monitoring using strain gauges and PZT sensors. GF-SMP layers have improved the impact resistance of the aluminium leading edge which is certainly encouraging towards finding a novel solution for the high-velocity impact.

High-velocity impact responses of 2618 aluminum plates for engine containment systems under combined actions of projectile form and oblique angle

Ballistic impact tests were carried out with examined projectiles of the Ti-6Al-4V titanium alloy to investigate the impact response of the 2618 aluminum plates at a nominal velocity of 210 m/s. The influence of projectile forms and oblique angles on damage formation was particularly discussed by applying different loading conditions such as multiple projectile forms and oblique angles. Additionally, the numerical simulation method was employed to provide further insight into the characteristics of damage and target responses. The Johnson-Cook(J-C)constitutive model with revised failure parameters was used to support the simulations to assess target responses and characteristics of the damage created from different impact conditions. Results show that there is a significant transition in the deformation mode as changes of the projectile form are applied. Moreover, the cracks on the back of the 2618 aluminum alloy plates impacted by the solid plate projectile and the hollow blade projectile tend to locate at different positions, which are supposed to be influenced by local bending and stretching. The work in this paper may provide guidance for the design of fan blade containment systems.

MECHANISM AND PREDICTION OF MATERIAL ABRASION IN HIGH-VELOCITY SEDIMENT-LADEN FLOW

The wall surface of material is prone to silt abrasion by high-velocity sediment-laden flow. The silt abrasion is different form cavitation erosion. In this article, the characteristics of silt abrasion were discussed, The mechanism of silt abrasion was analyzed and the formation and development of ripple shape on wall surface of material were explained thereafter. Based on turbulence theory and test data, some formulas were derived for predicting the abrasion rate of concrete wall surface in high-velocity sediment-laden flow. The calculated results show good agreement with the experimental data.

Microstructure and Wear Properties of Fe-based Amorphous Coatings Deposited by High-velocity Oxygen Fuel Spraying

Fe-based powder with a composition of Fe_（42.87）Cr_（15.98）Mo_（16.33）C_（15.94）B_（8.88）（at.%）was used to fabricate coatings by high-velocity oxygen fuel spraying.The effects of the spraying parameters on the microstructure and the wear properties of the Fe-based alloy coatings were systematically studied.The results showed that the obtained Fe-based coatings with a thickness of about 400μm consisted of a large-volume amorphous phase and some nanocrystals.With increasing the fuel and oxygen flow rates,the porosity of the obtained coatings decreased.The coating deposited under optimized parameters exhibited the lowest porosity of 2.8%.The excellent wear resistance of this coating was attributed to the properties of the amorphous matrix and the presence of nanocrystals homogeneously distributed within the matrix.The wear mechanism of the coatings was discussed on the basis of observations of the worn surfaces.

Seismic Acquisition Parameters Analysis for Deep Weak Reflectors in the South Yellow Sea

The Mesozoic-Paleozoic marine residual basin in the South Yellow Sea(SYS) is a significant deep potential hydrocarbon reservoir. However, the imaging of the deep prospecting target is quite challenging due to the specific seismic-geological conditions. In the Central and Wunansha Uplifts, the penetration of the seismic wavefield is limited by the shallow high-velocity layers(HVLs) and the weak reflections in the deep carbonate rocks. With the conventional marine seismic acquisition technique, the deep weak reflection is difficult to image and identify. In this paper, we could confirm through numerical simulation that the combination of multi-level air-gun array and extended cable used in the seismic acquisition is crucial for improving the imaging quality. Based on the velocity model derived from the geological interpretation, we performed two-dimensional finite difference forward modeling. The numerical simulation results show that the use of the multi-level air-gun array can enhance low-frequency energy and that the wide-angle reflection received at far offsets of the extended cable has a higher signal-to-noise ratio(SNR) and higher energy. Therefore, we have demonstrated that the unconventional wide-angle seismic acquisition technique mentioned above could overcome the difficulty in imaging the deep weak reflectors of the SYS, and it may be useful for the design of practical seismic acquisition schemes in this region.

Improvement in hot corrosion resistance of dissimilar alloy 825 and AISI 321 CO2-laser weldment by HVOF coating in aggressive salt environment at 900℃

This study investigated the hot corrosion performance of a dissimilar weldment of Ni-based superalloy and stainless steel joined by CO2-laser welding and improved by high-velocity oxy-fuel(HVOF)coating in a Na2SO4-60wt%V2O5 environment at 900℃.A dissimilar butt joint of AISI 321 and alloy 825 was fabricated by CO2-laser welding with low heat input after obtaining the optimum welding parameters by bead-on-plate trials.The metallurgical and mechanical properties of the laser weldment were evaluated.The tensile test results indicated the occurrence of fracture in the base metal AISI 321 side.The HVOF process was employed to coat Ni-20wt%Cr on the weldment.To evaluate the surface morphology of the corrosion products formed on the uncoated and Ni-20wt%Cr-coated weldments,scanning electron microscopy(SEM)analysis was performed.Energy-dispersive spectroscopy(EDS)was used to determine the different elements present on the surface scales.The existence of oxide phases on the weldments was determined by X-ray diffraction(XRD).The cross sections of the weldments were characterized by SEM with EDS line mapping analysis.The results indicated that the Ni-20wt%Cr-coated weldment exhibited superior hot corrosion resistance due to the development of Cr2O3 and NiCr2O4 protective oxide scales.

Microstructural analysis and hot corrosion behavior of HVOF-sprayed Ni–22Cr–10Al–1Y and Ni–22Cr–10Al–1Y–SiC(N) coatings on ASTM-SA213-T22 steel

The present paper deals with the investigation of microstructure and high-temperature hot corrosion behavior of high-velocity oxy fuel(HVOF)-produced coatings. Two powder coating compositions, namely, Ni22Cr10Al1Y alloy powder and Ni22Cr10Al1Y(80 wt%;microsized)–silicon carbide(SiC)(20 wt%;nano(N)) powder, were deposited on a T-22 boiler tube steel. The hot corrosion behavior of bare and coated steels was tested at 900°C for 50 cycles in Na2SO4–60 wt%V2O5 molten-salt environment. The kinetics of corrosion was established with weight change measurements after each cycle. The microporosity and microhardness of the as-coated samples have been reported. The X-ray diffraction,field emission-scanning electron microscopy/energy dispersive spectroscopy, and X-ray mapping characterization techniques have been utilized for structural analysis of the as-coated and hot-corroded samples. The results showed that both coatings were deposited with a porosity less than2%. Both coated samples revealed the development of harder surfaces than the substrate. During hot corrosion testing, the bare T22 steel showed an accelerated corrosion in comparison with its coated counterparts. The HVOF-sprayed coatings were befitted effectively by maintaining their adherence during testing. The Ni22Cr10Al1Y–20 wt%SiC(N) composite coating was more effective than the Ni–22Cr–10Al–1Y coating against corrosion in the high-temperature fluxing process.

Transfer Ionization of Helium in Collisions with C^q＋ and O^q＋ （q =1 - 3）

Cross-section ratios σTI/σSC of transfer ionization （TI） to single capture （SC） of C^q＋- and O^q＋-He （q = 1 - 3） collisions in the energy range of 15-440 keV/u （0.8-4.2 vBohr） are experimentally determined. It is shown that σTI/σSC strongly depends on the projectile velocity, and there is a maximum for E（keV/u）/q1/2 ≈, 150. Combining the Bohr-Lindhard model and the statistical model, a theoretical estimate is presented, in reasonable agreement with the experimental data when E（keV//u）/q^1/2 〉 35.

Influence of metal/composite interface on the damage behavior and energy absorption mechanisms of FMLs against projectile impact

This paper focuses on the interface failure in metal/GFRP laminates on account of the high-velocity impact phenomenon by a hemispherical projectile.The study considers three laminates in which the failure inside the 8-layer 0/90 GFRP laminate is compared with the other two laminates that include metal layers in their layup configuration.The metal layers were placed on the top and bottom on one type of laminates while in the other additional metal layers are placed symmetrically inside the layup as well.They were subjected to high-velocity impact by a hemispherical projectile at different energy levels and the idea is not to perforate the laminate configuration instead to account for the damage incurred in these laminates and the role of metal layers in providing resistance to damage within these laminates.The study utilizes experimental findings and proposes a rate-dependent Finite Element(FE)model consisting of the Hashin-Puck failure scheme for composite and the Johnson-Cook damage model for metal layers.The results of the model satisfactorily agree with their experimental counterparts and provide valuable insight into the damage resistance inside the laminates.It has been observed that the 8-layer GFRP laminate was good in terms of elastic recovery and prevention of propagation of damage inside the laminates only,till the impact energy was lower.For higher impact energy,they show poor damage resistance as the fiber failure is triggered in them.However,laminates with metal layers are shown to protect the laminate by dissipating energy in the delamination of metal/GFRP interface,shear failure of the metal layer,and on account of metal plasticity.The study further shows that the throughthickness compressive stresses were responsible for the failure of laminates and also triggering the delamination in them.A damage energy study was performed to investigate the amount of energy dissipating in various failure modes like delamination,matrix cracking,fiber failure,etc。

Characteristics of crustal variation and extensional break-up in the Western Pacific back-arc region based on a wide-angle seismic profile

The marginal sea and back-arc basins in the Western Pacific Ocean have become the focus of tectonics due to their unique tectonic location.To understand the deep crustal structure in the back-arc region,we present a 545-kmlong active-source ocean bottom seismometer(OBS)wide-angle reflection/refraction profile in the East China Sea.The P wave velocity model shows that the Moho depth rises significantly,from approximately 30 km in the East China Sea shelf to approximately 16 km in the axis of the Okinawa Trough.The lower crustal high-velocity zone(HVZ)in the southern Okinawa Trough,with V_(p) of 6.8-7.3 km/s,is a remarkable manifestation of the mantle material upwelling and accretion to the lower crust.This confirms that the lower crustal high-velocity mantle accretion is developed in the southern Okinawa Trough.During the process of back-arc extension,the crustal structure of the southern Okinawa Trough is completely invaded and penetrated by the upper mantle material in the axis region.In some areas of the southern central graben,the crust may has broken up and entered the initial stage of seafloor spreading.The discontinuous HVZs in the lower crust in the back-arc region also indicate the migration of spreading centers in the back-arc region since the Cenozoic.The asthenosphere material upwelling in the continent-ocean transition zone is constantly driving the lithosphere eastward for episodic extension,and is causing evident tectonic migration in the Western Pacific back-arc region.

Thermo-Rheological Structure and Passive Continental Margin Rifting in the Qiongdongnan Basin, South China Sea, China

To investigate the thermo-rheological structure and passive continental margin rifting in the Qiongdongnan Basin(QDNB),thermo-rheological models of two profiles across the western and eastern QDNB are presented.The continental shelf of western QDNB,having the lowest crustal extension factor,is recognized as the initial non-uniform extension crust model.This regime is referred to as the jelly sandwich-1(JS-1)regime,having a lower crustal ductile layer.The oceanward part of the western QDNB changes from the relatively strong JS-1 to the weak crème brûlée-1(CB-1)regime with a significantly thinned lower crust.However,the crustal extension in the eastern QDNB is significantly higher than that in the western QDNB,with conjugate faults extending deep into the lower crust.The central depression zone of the eastern QDNB is defined as the much stronger JS-2 regime,having a brittle deformation across the entire crust and upper mantle and characteristics of a cold and rigid oceanic crust.Unlike the widespread lower crustal high-velocity layers(HVLs)in the northern margin of the South China Sea,the HVLs are confined to the lower crustal base of the central depression zone of the QDNB.The HVLs of QDNB are the results of non-uniform extension with mantle underplating during the lower crustal-necking stage,which is facilitated by the lower crustal ductile layer and derived by mantle lat-eral flowing.The gigantic mantle low-velocity zone related to the Red River Fault should be a necessary factor for the east-west differential margin rifting process of QDNB,which may drive the lateral flowing in the mantle.