Hilbert-Huang transform and wavelet analysis of time history signal

The brief theories of wavelet analysis and Hilbert-Huang transform (HHT) are introduced firstly in the present paper. Then several signal data were analyzed by using wavelet and HHT methods, respectively. The comparison shows that HHT is not only an effective method for analyzing non-stationary data, but also is a useful tool for examining detailed characters of time history signal.

Enhanced Fourier Transform Using Wavelet Packet Decomposition

Many domains, including communication, signal processing, and image processing, use the Fourier Transform as a mathematical tool for signal analysis. Although it can analyze signals with steady and transitory properties, it has limits. The Wavelet Packet Decomposition (WPD) is a novel technique that we suggest in this study as a way to improve the Fourier Transform and get beyond these drawbacks. In this experiment, we specifically considered the utilization of Daubechies level 4 for the wavelet transformation. The choice of Daubechies level 4 was motivated by several reasons. Daubechies wavelets are known for their compact support, orthogonality, and good time-frequency localization. By choosing Daubechies level 4, we aimed to strike a balance between preserving important transient information and avoiding excessive noise or oversmoothing in the transformed signal. Then we compared the outcomes of our suggested approach to the conventional Fourier Transform using a non-stationary signal. The findings demonstrated that the suggested method offered a more accurate representation of non-stationary and transient signals in the frequency domain. Our method precisely showed a 12% reduction in MSE and a 3% rise in PSNR for the standard Fourier transform, as well as a 35% decrease in MSE and an 8% increase in PSNR for voice signals when compared to the traditional wavelet packet decomposition method.

A technique to improve the empirical mode decomposition in the Hilbert-Huang transform

The Hilbert-based time-frequency analysis has promising capacity to reveal the time-variant behaviors of a sys- tem.To admit well-behaved Hilbert transforms,component decomposition of signals must be performed beforehand.This was first systematically implemented by the empirical mode decomposition(EMD)in the Hilbert-Huang transform,which can provide a time-frequency representation of the signals.The EMD,however,has limitations in distinguishing different components in narrowband signals commonly found in free-decay vibration signals.In this study,a technique for decompo- sing components in narrowband signals based on waves' beating phenomena is proposed to improve the EMD,in which the time scale structure of the signal is unveiled by the Hilbert transform as a result of wave beating,the order of component ex- traction is reversed from that in the EMD and the end effect is confined.The proposed technique is verified by performing the component decomposition of a simulated signal and a free decay signal actually measured in an instrumented bridge structure.In addition,the adaptability of the technique to time-variant dynamic systems is demonstrated with a simulated time-variant MDOF system.

Floating Clamping Mechanism of PT Fuel Injector and Its Dynamic Characteristics Analysis

PT fuel injector is one of the most important parts of modern diesel engine.To satisfy the requirements of the rapid and accurate test of PT fuel injector,the self-adaptive floating clamping mechanism was developed and used in the relevant bench.Its dynamic characteristics directly influence the test efficiency and accuracy.However,due to its special structure and complex oil pressure signal,related documents for evaluating dynamic characteristics of this mechanism are lack and some dynamic characteristics of this mechanism can＇t be extracted and recognized effectively by traditional methods.Aiming at the problem above-mentioned,a new method based on Hilbert-Huang transform（HHT） is presented.Firstly,combining with the actual working process,the dynamic liquid pressure signal of the mechanism is acquired.By analyzing the pressure fluctuation during the whole working process in time domain,oil leakage and hydraulic shock in the clamping chamber are discovered.Secondly,owing to the nonlinearity and nonstationarity of pressure signal,empirical mode decomposition is used,and the signal is decomposed and reconstructed into forced vibration,free vibration and noise.By analyzing forced vibration in the time domain,machining error and installation error of cam are revealed.Finally,free vibration component is analyzed in time-frequency domain with HHT,the traits of free vibration in the time-frequency domain are revealed.Compared with traditional methods,Hilbert spectrum has higher time-frequency resolutions and higher credibility.The improved mechanism based on the above analyses can guarantee the test accuracy of injector injection.This new method based on the analyses of the pressure signal and combined with HHT can provide scientific basis for evaluation,design improvement of the mechanism,and give references for dynamic characteristics analysis of the hydraulic system in the interrelated fields.

DOPPLERLET BASED TIME-FREQUENCY REPRESENTATION VIA MATCHING PURSUITS

A new time-frequency representation called Dopplerlet transform, which uses the dilated, translated and modulated windowed Doppler signals as its basis functions, is proposed, and the Fourier transform, short-time Fourier transform (including Gabor transform), wavelet transform, and chirplet transform are formulated in one framework of Dopplerlet transform accordingly.It is proved that the matching pursuits based on Dopplerlet basis functions are convergent, and that the energy of residual signals yielded in the decomposition process decays exponentially. Simulation results show that the matching pursuits with Dopplerlet basis functions can characterize compactly a nonstationary signal.

IDENTIFICATION OF NONLINEAR DYNAMIC SYSTEMS:TIME-FREQUENCY FILTERING AND SKELETON CURVES

The nonlinear behavior varying with the instantaneous response was analyzed through the joint time-frequency analysis method for a class of S. D. O. F nonlinear system. A masking operator an definite regions is defined and two theorems are presented. Based on these, the nonlinear system is modeled with a special time-varying linear one, called the generalized skeleton linear system (GSLS). The frequency skeleton curve and the damping skeleton curve are defined to describe the main feature of the non-linearity as well. Moreover, an identification method is proposed through the skeleton curves and the time-frequency filtering technique.

Mathematical theory of signal analysis vs. complex analysis method of harmonic analysis

We present recent work of harmonic and signal analysis based on the complex Hardy space approach.

Wind Turbine Planetary Gearbox Fault Diagnosis via Proportion-Extracting Synchrosqueezing Chirplet Transform

Wind turbine planetary gearboxes usually work under time-varying conditions,leading to nonstationary vibration signals.These signals often consist of multiple time-varying components with close instantaneous frequencies.Therefore,high-quality time-frequency analysis(TFA)is needed to extract the time-frequency feature from such nonstationary signals for fault diagnosis.However,it is difficult to obtain high-quality timefrequency representations(TFRs)through conventional TFA methods due to low resolution and time-frequency blurs.To address this issue,we propose a new TFA method termed the proportion-extracting synchrosqueezing chirplet transform(PESCT).Firstly,the proportion-extracting chirplet transform is employed to generate highresolution underlying TFRs.Then,the energy concentration of the underlying TFRs is enhanced via the synchrosqueezing transform.Finally,wind turbine planetary gearbox fault can be diagnosed by analysis of the dominant time-varying components revealed by the concentrated TFRs with high resolution.The proposed PESCT is suitable for achieving high-quality TFRs for complicated nonstationary signals.Numerical and experimental analyses validate the effectiveness of the PESCT in characterizing the nonstationary signals from wind turbine planetary gearboxes.

Applications of the Hilbert-Huang Transform for Microtremor Data Analysis Enhancement

In this paper we discuss the use of the Hilbert-Huang transform（HHT） to enhance the time-frequency analysis of microtremor measurements. HHT is a powerful algorithm that combines the process of empirical mode decomposition（EMD） and the Hilbert transform to compose the HilbertHuang spectrum that contains the time-frequency-energy information of the recorded signals. HHT is an adaptive algorithm and does not require the signals to be linear or stationary. HHT is advantageous for analyzing microtremor data, since observed microtremors are commonly contaminated by nonstationary transient noises close to the recording instruments. This is especially true when microtremors are measured in an urban environment. In our data processing HHT was used to（1） eliminate the unwanted short-duration transient constituents from microtremor data and use only the coherent portion of the data to carry out the widely used horizontal to vertical spectral ratio（H/V） method;（2） identify and eliminate the continuous industrial noise in certain frequency band; and（3） enhance the H/V analysis by using the Hilbert-Huang spectrum（HHS）. The efficacy of this proposed approach is demonstrated by the examples of applying it to microtremor data acquired in the metropolitan Beijing area.

Local Extrema of Periodic Function’s Wavelet Transform

The theory of detecling ridges in the modulus of the continuous wavelet transform is presented as well as reconstructing signal by using information on ridges,To periodic signal we suppose Morlet wavelet as basic wavelet, and research the local extreme point and extrema of the wavelet transform on periodic function for the collection of signal＇ s instantaneous amplitude and period.

Radar Signal Intra-Pulse Feature Extraction Based on Improved Wavelet Transform Algorithm

With the new system radar put into practical use, the characteristics of complex radar signals are changing and developing. The traditional analysis method of one-dimensional transformation domain is no longer applicable to the modern radar signal processing, and it is necessary to seek new methods in the two-dimensional transformation domain. The time-frequency analysis method is the most widely used method in the two-dimensional transformation domain. In this paper, two typical time-frequency analysis methods of short-time Fourier transform and Wigner-Ville distribution are studied by analyzing the time-frequency transform of typical radar reconnaissance linear frequency modulation signal, aiming at the problem of low accuracy and sen-sitivity to the signal noise of common methods, the improved wavelet transform algorithm was proposed.

Three-dimensional reconstruction of precession warhead based on multi-view micro-Doppler analysis

The warhead of a ballistic missile may precess due to lateral moments during release. The resulting micro-Doppler effect is determined by parameters such as the target's motion state and size. A three-dimensional reconstruction method for the precession warhead via the micro-Doppler analysis and inverse Radon transform(IRT) is proposed in this paper. The precession parameters are extracted by the micro-Doppler analysis from three radars, and the IRT is used to estimate the size of targe. The scatterers of the target can be reconstructed based on the above parameters. Simulation experimental results illustrate the effectiveness of the proposed method in this paper.

Extraction of MHD Signal Based on Wavelet Transform

Mirnov signals mixed with interferences are a kind of non-stationary signal. It cannot obtain satisfactory effects to extract MHD signals from mirnov signals by Fourier Transform. This paper suggests that the wavelet transform can be used to treat mirnov signals. Theoretical analysis and experimental result have indicated that using the time-frequency analysis characteristics of the wavelet transform to filter mirnov signals can remove effectively interferences and extract useful MHD signals.

Roll angular rate extraction based on modified spline-kernelled chirplet transform

The roll angular rate is much crucial for the guidance and control of the projectile.Yet the high-speed rotation of the projectile brings severe challenges to the direct measurement of the roll angular rate.Nevertheless,the radial magnetometer signal is modulated by the high-speed rotation,thus the roll angular rate can be achieved by extracting the instantaneous frequency of the radial magnetometer signal.The objective of this study is to find out a precise instantaneous frequency extraction method to obtain an accurate roll angular rate.To reach this goal,a modified spline-kernelled chirplet transform(MSCT)algorithm is proposed in this paper.Due to the nonlinear frequency modulation characteristics of the radial magnetometer signal,the existing time-frequency analysis methods in literature cannot obtain an excellent energy concentration in the time-frequency plane,thereby leading to a terrible instantaneous frequency extraction accuracy.However,the MSCT can overcome the problem of bad energy concentration by replacing the short-time Fourier transform operator with the Chirp Z-transform operator based on the original spline-kernelled chirplet transform.The introduction of Chirp Z-transform can improve the construction accuracy of the transform kernel.Since the construction accuracy of the transform kernel determines the concentration of time-frequency distribution,the MSCT can obtain a more precise instantaneous frequency.The performance of the MSCT was evaluated by a series of numerical simulations,high-speed turntable experiments,and real flight tests.The evaluation results show that the MSCT has an excellent ability to process the nonlinear frequency modulation signal,and can accurately extract the roll angular rate for the high spinning projectiles.

Application of short-time Fourier transform to high-rise frame structural-health monitoring based on change of inherent frequency over time

The high-rise frame structure has become more and more widespread, like its damage from the complication of the environment. The traditional method of damage detection, which is only suitable for the stationary signal, does not apply to a high-rise frame structure because its damage signal is non-stationary. Thus, this paper presents an application of the short-time Fourier transform(STFT) to damage detection of high-rise frame structures. Compared with the fast Fourier transform, STFT is found to be able to express the frequency spectrum property of the time interval using the signal within this interval. Application of STFT to analyzing a Matlab model and the shaking table test with a twelve-story frame-structure model reveals that there is a positive correlation between the slope of the frequency versus time and the damage level. If the slope is equal to or greater than zero, the structure is not damaged. If the slope is smaller than zero, the structure is damaged, and the less the slope is, the more serious the damage is. The damage results from calculation based on the Matlab model are consistent with those from the shaking table test, demonstrating that STFT can be a reliable tool for the damage detection of high-rise frame structures.

SAR target detection based on the optimal fractional Gabor spectrum feature

In this paper,an algorithm based on a fractional time-frequency spectrum feature is proposed to improve the accuracy of synthetic aperture radar(SAR)target detection.By extending the fractional Gabor transform(FrGT)into two dimensions,the fractional time-frequency spectrum feature of an image can be obtained.In the achievement process,we search for the optimal order and design the optimal window function to accomplish the two-dimensional optimal FrGT.Finally,the energy attenuation gradient(EAG)feature of the optimal time-frequency spectrum is extracted for high-frequency detection.The simulation results show the proposed algorithm has a good performance in SAR target detection and lays the foundation for recognition.

Output-only identification of the modal and physical properties of structures using free vibration response

The viability of a complete structural characterization of civil structures is explored and discussed. In particular, the identification of modal （i.e. natural frequencies, damping ratios and modal shapes） and physical properties （i.e. mass and stiffness） using only the structure＇s free decay response is studied. To accomplish this, modal analysis from flee vibration response only （MAFVRO） and mass modification （MM） methodologies are engaged along with Wavelet based techniques for optimal signal processing and modal reconstruction. The methodologies are evaluated using simulated and experimental data. The simulated data are extracted from a simple elastic model of a 5 story shear building and from a more realistic nonlinear model of a RC frame structure. The experimental data are gathered from shake table test of a 2-story scaled shear building. Guidelines for the reconstruction procedure from the data are proposed as the quality of the identified properties is shown to be governed by adequate selection of the frequency bands and optimal modal shape reconstruction. Moreover, in cases where the structure has undergone damage, the proposed identification scheme can also be applied for preliminary assessment of structural health.

Spatial transformation of general sampling-aliasing frequency region for rotating-blade parameter identification with emphasis on single-probe blade tip-timing measurement

Blade-health monitoring is intensely required for turbomachinery because of the high failure risk of rotating blades.Blade-Tip Timing(BTT)is considered as the most promising technique for operational blade-vibration monitoring,which obtains the parameters that characterize the blade condition from recorded signals.However,its application is hindered by severe undersampling and stringent probe layouts.An inappropriate probe layout can make most of the existing methods invalid or inaccurate.Additionally,a general conflict arises between the allowed and required layouts because of arrangement restrictions.For the sake of economy and safety,parameter identification based on fewer probes has been preferred by users.In this work,a spatial-transformation-based method for parameter identification is proposed based on a single-probe BTT measurement.To present the general Sampling-Aliasing Frequency(SAFE)map definition,the traditional time-frequency analysis methods are extended to a time-sampling frequency.Then,a SAFE map is projected onto a parameter space using spatial transformation to extract the slope and intercept parameters,which can be physically interpreted as an engine order and a natural frequency using coordinate transformation.Finally,the effectiveness and robustness of the proposed method are verified by simulations and experiments under uniformly and nonuniformly variable speed conditions.

Research progress of the fractional Fourier transform in signal processing

The fractional Fourier transform is a generalization of the classical Fourier transform, which is introduced from the mathematic aspect by Namias at first and has many applications in optics quickly. Whereas its potential appears to have remained largely unknown to the signal processing community until 1990s. The fractional Fourier transform can be viewed as the chirp-basis expansion directly from its definition, but essentially it can be interpreted as a rotation in the time-frequency plane, i.e. the unified time-frequency transform. With the order from 0 increasing to 1, the fractional Fourier transform can show the characteristics of the signal changing from the time domain to the frequency domain. In this research paper, the fractional Fourier transform has been comprehensively and systematically treated from the signal processing point of view. Our aim is to provide a course from the definition to the applications of the fractional Fourier transform, especially as a reference and an introduction for researchers and interested readers.

A distribution space for Hilbert transform and its applications

In this paper, a new distribution space DH is constructed and the definition of the classical Hilbert transform is extended to it. It is shown that DH is the biggest subspace of D on which the extended Hilbert transform is a homeomorphism and both the classical Hilbert transform for Lp functions and the circular Hilbert transform for periodic functions are special cases of the extension. Some characterizations of the space DH are given and a class of useful nonlinear phase signals is shown to be in DH. Finally, the applications of the extended Hilbert transform are discussed.