Stress release mechanism of deep bottom hole rock by ultra-high-pressure water jet slotting

To solve the problems of rock strength increase caused by high in-situ stress,the stress release method with rock slot in the bottom hole by an ultra-high-pressure water jet is proposed.The stress conditions of bottom hole rock,before and after slotting are analyzed and the stress release mechanism of slotting is clarified.The results show that the stress release by slotting is due to the coupling of three factors:the relief of horizontal stress,the stress concentration zone distancing away from the cutting face,and the increase of pore pressure caused by rock mass expansion;The stress concentration increases the effective stress of rock along the radial distance from O.6R to 1R(R is the radius of the well),and the presence of groove completely releases the stress,it also allows the stress concentration zone to be pushed away from the cutting face,while significantly lowering the value of stresses in the area the drilling bit acting,the maximum stress release efficiency can reach 80%.The effect of slotting characteristics on release efficiency is obvious when the groove location is near the borehole wall.With the increase of groove depth,the stress release efficiency is significantly increased,and the release range of effective stress is enlarged along the axial direction.Therefore,the stress release method and results of simulations in this paper have a guiding significance for best-improving rock-breaking efficiency and further understanding the technique.

Research advances on encapsulation of probiotics with nanomaterials and their repair mechanisms on intestinal barriers

Probiotics participate in various physiological activities and contribute to body health.However,their viability and bioefficacy are adversely affected by gastrointestinal harsh conditions,such as gastric acid,bile salts and various enzymes.Fortunately,encapsulation based on various nanomaterials shows tremendous potential to protect probiotics.In this review,we introduced some novel encapsulation technologies involving nanomaterials in view of predesigned stability and viability,selective adhesion,smart release and colonization,and efficacy exertion of encapsulated probiotics.Furthermore,the interactions between encapsulated probiotics and the gastrointestinal tract were summarized and analyzed,with highlighting the regulatory mechanisms of encapsulated probiotics on intestinal mechanical barrier,chemical barrier,biological barrier and immune barrier.This review would benefit the food and pharmaceutical industries in preparation and utilization of multifunctional encapsulated probiotics.

Nanoencapsulation of Antioxidant-Rich Fraction of Roasted <i>Moringa oleifera</i>L. Leaf Extract: Physico-Chemical Properties and <i>in Vitro</i>Release Mechanisms

Nanocapsules (NC) of antioxidant rich fraction of roasted Moringa leaves were prepared using emulsion coacervation technique with alginate (ALG) and/or chitosan (CTS) as biopolymers. NC were characterized based on particle size, polydispersity index (PDI), zeta potential, encapsulation efficiency (EE) and loading capacity (LC). Substituting CTS with ALG in NC caused a reduction in particle size and PDI, and enhanced EE. Mean particle size dropped from 1209 nm in 1:3 to 413 nm in 3:1 ALG/CTS-NC;PDI decreased from 0.9% to 0.2% and zeta potential from -5.4 to -28.1 mV. The highest EE (87.6%) and LC (13%) were obtained with ALG-CTS-NC (3:1). ALG-NC were spherical while both CTS and ALG-CTS-NC were ovoid. ALG and ALG-CTS-NC were oil/water emulsions while CTS-NC formed water/oil emulsions. 60% and 70% of bioactives in ALG-CTS-NC (3:1) were released in simulated gastric and intestinal fluids respectively after 400 min. Release of antioxidants from NC is concentration-dependent (First order model) and involves simultaneously diffusion (Higuchi model), swelling (korsmeyer-Peppas model) and erosion (Hixson-Crowell model) mechanisms.

Design of a Mechanical Release System of Predator Insects to Control the Colorado Potato Beetle, Leptinotarsa Decemlineata （Say）

The CPB （Colorado potato beetle）, Leptinotarsa decemlineata （Say）, is the major insect pest of potato crops in North America, Europe and Asia. Large amounts of chemical insecticides are used to control this insect pest. Also, the CPB has developed over the years a resistance to most of the registered chemical insecticides, including those that were effective at one time. One of the most promising alternatives to chemical insecticides consists of taking advantage of natural enemies. The use of the stinkbug predator Perillus bioculatus to control the CPB has been successful at small scale. However, this natural enemy is not abundant in the nature and its hand release at large scale is not realistic. To remedy to this problem, predators must be massively released in potato fields using a mechanical distributor. Such a machine has been successfully designed and built at the Department of Soils and Agri-Food Engineering of University Lavak In this distributor, masses of predators are placed in small containers and mixed with a carrier material. In the field, the containers are mechanically opened at different locations, based on a source-point mass release option. These locations are determined in advance following a field monitoring of the populations of CPBs. Field trials proved that the mechanical distributor is reliable and ease of use. Its efficiency in releasing insect predators is high and comparable to that obtained in previous laboratory tests.

Effect of thermal and chemical modifications on the mechanical and release properties of paracetamol tablet formulations containing corn, cassava and sweet potato starches as filler-binders

Objective: To investigate the effects of acetylation and pregelatinization of cassava and sweet potato starches on the mechanical and release properties of directly compressed paracetamol tablet formulations in comparison with official corn starch.Methods: The native starches were modified by acetylation and pregelatinization. The tablets were assessed using friability(Fr), crushing strength(Cs), disintegration time(Dt) and dissolution parameters. Results: Starch acetylation produced paracetamol tablets that were stronger and had the best balance of mechanical and disintegration properties, while pregelatinization produced tablets that were more friable but had a better overall strength in relation to disintegration than formulations made from natural starches. Correlations mainly existed between Dt and the dissolution parameters t80, t2 and k1 in the formulations. Conclusions: Modification of the experimental starches improved the mechanical and release properties of directly compressed paracetamol tablet formulations. Thus, they can be developed for use as pharmaceutical excipients in specific formulations.

Control of the Colorado Potato Beetle, Leptinotarsa decemlineata （Say）, Using Predator Insects Released by a Mechanical Prototype

The CPB （Colorado potato beetle） is unquestionably the major insect pest of potato crops in North America, Europe, and Asia. The use of chemical insecticides to control this insect pest started in the 1860s. To date, no registered chemical has been capable of effectively managing this agricultural pest. Moreover, the CPB has developed over the years a resistance to most of the registered chemical insecticides. The biological control through manual release of natural enemies of the CPB has been successful at small scale. However, hand release of these predators at large scale is not realistic. The objective of this study was to investigate the effectiveness of controlling the CPB through mechanical release of predator insects under real conditions in a potato field. Obtained results indicate that the mechanical release of predator insects resulted in a better control of the CPB populations and egg masses than the manual release. The success of this mechanical release of predator insects in potato fields will be highly valuable for the biological control of insect pests in many other row crops such as strawberry, lettuce, etc..

Review on Zinc Oxide Nanoparticles: Antibacterial Activity and Toxicity Mechanism

Antibacterial activity of zinc oxide nanoparticles(Zn O-NPs) has received significant interest worldwide particularly by the implementation of nanotechnology to synthesize particles in the nanometer region. Many microorganisms exist in the range from hundreds of nanometers to tens of micrometers. Zn O-NPs exhibit attractive antibacterial properties due to increased specific surface area as the reduced particle size leading to enhanced particle surface reactivity. Zn O is a bio-safe material that possesses photo-oxidizing and photocatalysis impacts on chemical and biological species. This review covered Zn O-NPs antibacterial activity including testing methods, impact of UV illumination, Zn O particle properties(size, concentration, morphology, and defects), particle surface modification, and minimum inhibitory concentration. Particular emphasize was given to bactericidal and bacteriostatic mechanisms with focus on generation of reactive oxygen species(ROS) including hydrogen peroxide(H2O2), OH-(hydroxyl radicals), and O2-2(peroxide). ROS has been a major factor for several mechanisms including cell wall damage due to Zn O-localized interaction, enhanced membrane permeability, internalization of NPs due to loss of proton motive force and uptake of toxic dissolved zinc ions.These have led to mitochondria weakness, intracellular outflow, and release in gene expression of oxidative stress which caused eventual cell growth inhibition and cell death. In some cases, enhanced antibacterial activity can be attributed to surface defects on Zn O abrasive surface texture. One functional application of the Zn O antibacterial bioactivity was discussed in food packaging industry where Zn O-NPs are used as an antibacterial agent toward foodborne diseases. Proper incorporation of Zn O-NPs into packaging materials can cause interaction with foodborne pathogens, thereby releasing NPs onto food surface where they come in contact with bad bacteria and cause the bacterial death and/or inhibition.

Assessment of rockburst hazard by quantifying the consequence with plastic strain work and released energy in numerical models

Quantifying the rockburst consequence is of critical importance to reduce the hazards with preventative measures in underground mines and deep tunnels. Contours of energy components within a pillar model are plotted at different rockmass damage stages, and plastic strain work and released energy are proposed as indicators of rockmass damage consequence. One pillar model under different loading stiffness is simulated to assess indicators of pillar burst and the resulting damages. The results show the rockmass damage under soft loading stiffness has larger magnitude of plastic strain work and released energy than that which is under stiff loading stiffness, indicating the rockburst consequence can be quantified with plastic strain work and released energy in numerical models. With the quantified rockburst consequence,preventative measures can be taken to avoid severe hazards to mine safety.

Light-induced ZnO/Ag/rGO bactericidal photocatalyst with synergistic effect of sustained release of silver ions and enhanced reactive oxygen species

Silver nanoparticles (Ag NPs) can effectively address the issue of antibiotic-resistant bacterial infections to reduce the potential toxicity of Ag NPs. Although challenging, it is, therefore, necessary to achieve the sustainable release of Ag+ ions from a finite amount of Ag NPs. This study aims at designing an efficient and benign antimicrobial silver-based ternary composite composed of photocatalysis zinc oxide (ZnO) and reduced graphene oxide (rGO) as a carrier, in which the reactive oxygen species (ROS) excited from ZnO and Ag+ ions released from the Ag NPs cooperate to realize an effective antibacterial activity against E. coli and S. aureus. The constant effective bacterial performance of the ternary photocatalyst with minimum Ag content can be attributed to the increase in the available quantity of ROS, which results from the enhanced separation efficiency of the photogenerated carriers. The proposed system notably realized the long-term sustainable release of Ag+ ions with low concentration for 30 days when compared with an equivalent amount of silver nitrate. Moreover, the use of the composite prevents biotoxicity and silver wastage, and imparts enhanced stability to the long-lasting antibacterial efficacy.

Taste masking of ciprofloxacin by ion-exchange resin and sustain release at gastric-intestinal through interpenetrating polymer network

The aim of the study was to taste mask ciprofloxacin(CP)by using ion-exchange resins(IERs)followed by sustain release of CP by forming interpenetrating polymer network(IPN).IERs based on the copolymerization of acrylic acid with different cross linking agents were synthesised.Drug-resin complexes(DRCs)with three different ratios of drug to IERs(1:1,1:2,1:4)were prepared&evaluated for taste masking by following in vivo and in vitro methods.Human volunteers graded ADC 1:4,acrylic acid-divinyl benzene(ADC-3)resin as tasteless.Characterization studies such as FTIR,SEM,DSC,P-XRD differentiated ADC 1:4,from physical mixture(PM 1:4)and confirmed the formation of complex.In vitro drug release of ADC 1:4 showed complete release of CP within 60 min at simulated gastric fluid(SGF)i.e.pH 1.2.IPN beads were prepared with ADC 1:4 by using sodium alginate(AL)and sodium alginate-chitosan(AL-CS)for sustain release of CP at SGF pH and followed by simulated intestinal fluid(SIF i.e.pH 7.4).FTIR spectra confirmed the formation of IPN beads.The release of CP was sustain at SGF pH(<20%)whereas in SIF media it was more(>75%).The kinetic model of IPN beads showed the release of CP was non-Fickian diffusion type.

Preparation and evaluation of tamsulosin hydrochloride sustained-release pellets modified by two-layered membrane techniques

The aim of the present study was to develop tamsulosin hydrochloride sustained-release pellets using two-layered membrane techniques.Centrifugal granulator and fluidizedbed coater were employed to prepare drug-loaded pellets and to employ two-layered membrane coating respectively.The prepared pellets were evaluated for physicochemical characterization,subjected to differential scanning calorimetry(DSC)and in vitro release of different pH.Different release models and scanning electron microscopy(SEM)were utilized to analyze the release mechanism of Harnual■ and home-made pellets.By comparing the dissolution profiles,the ratio and coating weight gain of Eudragit■ NE30D and Eudragit■ L30D55 which constitute the inside membrane were identified as 18:1 and 10%-11%.The coating amount of outside membrane containing Eudragit■ L30D55 was determined to be 0.8%.The similarity factors(f_(2))of home-made capsule and commercially available product(Harnual■)were above 50 in different dissolution media.DSC studies confirmed that drug and excipients had good compatibility and SEM photographs showed the similarities and differences of coating surface between Harnual■ and self-made pellets before and after dissolution.According to Ritger-Peppas model,the two dosage form had different release mechanism.

Surface lurking and interfacial ion release strategy for fabricating a superhydrophobic coating with scaling inhibition

The design and manufacture of anti-scaling surface is a prospective way to prevent scaling in oil field.In this work,a novel superhydrophobic Cu^(2+)-loaded and DTPMPA-modified anodized copper oxide(S-Cu^(2+)/D-ACO)coating was fabricated by modification of 1H,1H,2H,2H-perfluorodecyltriethoxysilane.The valid storing of scale inhibitors at the coating surface and the interfacial release of Cu^(2+)ions contribute to enhancing the anti-scaling of the S-Cu^(2+)/D-ACO coating.The water contact angle of the S-Cu^(2+)/D-ACO coating is 163.03°and exhibits superhydrophobicity,which makes it difficult for CaCO_(3)to deposit at the surface of the coating.DTPMPA will steadily lurk into the inner space,and Cu^(2+)will be loaded at the interface in the form of the DTPMPA:Cu^(2+)chelate.During the deposition of CaCO_(3),the dynamic release of DTPMPA can be realized by transferring DTPMPA:Cu^(2+)to DTPMPA:Ca^(2+).Interestingly,the released Cu^(2+)hinders the active growth of CaCO_(3).After 48 h of scaling,the mass of CaCO_(3)scale at the S-Cu^(2+)/D-ACO coating surface is only 44.1%that of the anodized copper oxide coating.The excellent anti-scaling performance of the S-Cu^(2+)/D-ACO coating is determined by the synergistic effect of the DTPMPA lurking and dynamic release,as well as the Cu^(2+)inhibition at the interface of superhydrophobic coating and against CaCO_(3)deposition.This research provides a new exploration for designing and fabricating anti-scaling superhydrophobic surface for oil field development.

Physiological Basis of Photosynthetic Function and Senescence of Rice Leaves as Regulated by Controlled-Release Nitrogen Fertilizer

The physiological mechanism of photosynthetic function and senescence of rice leaves was studied by using early rice variety Baliangyou 100 and late rice variety Weiyou 46, treated with controlled-release nitrogen fertilizer （CRNF）, urea and no nitrogen fertilizer. CRNF showed obvious effects on delaying the senescence and prolonging photosynthetic function duration of rice leaves. Compared with urea, CRNF could significantly increase the chlorophyll content of functional leaves in both early and late rice varieties, and this difference between the treatments became larger as rice growth progressed; CRNF increased the activities of active oxygen scavenging enzymes super oxide dismutase （SOD） and peroxidase （POD）, and decreased the accumulation amount of malondialdehyde （MDA） in functional leaves during leaf aging; Photosynthetic rate of functional leaves in CRNF treatment was significantly higher than that in urea treatment. The result also indicated that CRNF could effectively regulate the contents of indole-3-acetic acid （IAA） and abscisic acid （ABA） in functional leaves; IAA content was higher and ABA content was lower in CRNF treatment than those in urea treatment. Therefore, application of CRNF could increase the rice yield significantly due to these physiological changes in the functional leaves.

Studies on the PEO-PPO-PEO Block Copolymer Release from Alginate Hydrogel

Alginate hydrogel is one of the most widely used carriers for the immobilization of microbial cells. If surfactants are encapsulated with alginate hydrogel, increasing temperature or concentration can make the encapsulated surfactants aggregate and form micelle.

Silicone matrices for controlled dexamethasone release:toward a better understanding of the underlying mass transport mechanisms

Dexamethasone-loaded silicone matrices offer an interesting potential as innovative drug delivery systems,e.g.for the treatment of inner ear diseases or for pacemakers.Generally,very long drug release periods are targeted:several years/decades.This renders the development and optimization of novel drug products cumbersome:experimental feedback on the impact of the device design is obtained very slowly.A better understanding of the underlying mass transport mechanisms can help facilitating research in this field.A variety of silicone films were prepared in this study,loaded with amorphous or crystalline dexamethasone.Different polymorphic drug forms were investigated,the film thickness was altered and the drug optionally partially/completely exchanged by much more water-soluble dexamethasone‘phosphate’.Drug release studies in artificial perilymph,scanning electron microscopy,optical microscopy,differential scanning calorimetry,X-ray diffraction and Raman imaging were used to elucidate the physical states of the drugs and polymer,and of the systems’structure as well as dynamic changes thereof upon exposure to the release medium.Dexamethasone particles were initially homogeneously distributed throughout the systems.The hydrophobicity of the matrix former very much limits the amounts of water penetrating into the system,resulting in only partial drug dissolution.The mobile drug molecules diffuse out into the surrounding environment,due to concentration gradients.Interestingly,Raman imaging revealed that even very thin silicone layers(<20µm)can effectively trap the drug for prolonged periods of time.The physical state of the drug(amorphous,crystalline)did not affect the resulting drug release kinetics to a noteworthy extent.

Comparison of nickle release and cytocompatibility between porous and dense NiTi alloy

The porous NiTi(pNiTi)samples were produced by sintering evaporation using Ti−50.8Ni(at.%)gasatomized powders.The samples were analyzed by metallographic microscope and X-ray dispersive spectroscopy(XRD).A comparison of nickel(Ni)release and cytocompatibility between pNiTi and dense NiTi(dNiTi)was made.The results showed that the pNiTi has good mechanical properties.Ni releases from pNiTi in vitro and in vivo are more serious than those form dNiTi.The proliferation and differentiation of cells cultured with the pNiTi extracting liquid are significantly worse,and the rate of early apoptosis is higher.In conclusion,pNiTi is mechanically similar to bone,but pNiTi releases more Ni and interferes with cell proliferation and differentiation.A significantly cautious approach should be adopted when using it as a medical implant.

Airway Pressure Release Ventilation Improves Oxygenation in a Patient with Pulmonary Hypertension and Abdominal Compartment Syndrome

The following case describes the favorable application of airway pressure release ventilation (APRV) in a patient with pulmonary hypertension who developed respiratory failure and abdominal compartment syndrome after abdominal closure from an incarcerated umbilical hernia. A 66-year-old male with past medical history of restrictive lung disease, obstructive sleep apnea and pulmonary hypertension, presented to the operating room for an incarcerated inguinal hernia. After abdominal closure, he gradually developed decreased oxygen saturation and hypotension. APRV was initiated during post operative day 2 after inability to maintain adequate oxygen saturation with resultant hypotension on pressure control ventilation with varying degrees of positive end expiratory pressure and 100% inspired oxygen concentration. The initial set high pressure on APRV was 35 mm Hg. Yet, in lieu of decreasing lung compliance, it peaked at 50 mm Hg. Eventually, inhaled Nitric Oxide was initiated post operative day 3 due to increasing pulmonary arterial pressures. A bedside laparotomy was eventually performed when bladder pressures peaked to 25 mm Hg. APRV gradually and temporally improved the oxygen saturation and decreased the pulmonary arterial pressures with subsequent increase in systemic blood pressures. APRV promoted alveolar recruitment and decreased the shunting associated with abdominal compartment syndrome. Better oxygen saturations lead to increases in blood pressure by decreasing the effects of hypoxic pulmonary vasoconstriction on the right ventricle (RV). In patients with decreasing lung compliance and pulmonary comorbidities, APRV appears safe and allows for improve oxygenation, after failure with conventional modes of ventilation.

The release of ^(14)C-chlorsulfuron bound residue by autoclaving method and its identification

When individual microorganisms were used to release bound pesticide residues, it was ussually not take into full account whether the autoclavingmethod could lead to the release of bound residues. The soil containing bound 14Cchlorsulfuron residues was treated with an autoclave in this study. The results revealthat the bound 14C-chlorsulfuron residue can be released from the soil when treatedwith the autoclave and the release rate can be remarkably enhanced by adding water into the soil when subjected to such treatment. A TLC analysis showed that thereleased 14C-residue was one of the degraded products of 14C-chlorsulfuron. Afterderivatization and analysis using the GC-MS, the released 14C-residue was tentativelyidentified aS 2-amino-4-hydroXyl-6-methyl-1,3,

The Impact of Different Mining and Releasing Ratios on the Over-Support Pressure of Header Working Face

Through the theoretical analysis of overburden destabilization mechanism, FLAC 3D simplified plane numerical simulation method and field measurement method, we compared the relationship of overburden support pressure at 35 m of workface recovery, and the peak overburden support pressure decreased from 13.85 Mpa to 11.97 Mpa from 1:1 to 1:3. With the increase of mining ratio, the peak over-supporting pressure decreases: with the increase of top coal recovery thickness, the peak over-supporting pressure and the influence range will be further expanded, and the distance between the peak over-supporting pressure and the coal wall of the working face will be further increased and the high stress zone of the peak area will be expanded simultaneously.