Hole-drilling method using grating rosette and Moire interferometry

The hole-drilling method is one of the most wellknown methods for measuring residual stresses. To identify unknown plane stresses in a specimen, a circular hole is first drilled in the infinite plate under plane stress, then the strains resulting from the hole drilling is measured. The strains may be acquired from interpreting the Moire signature around the hole. In crossed grating Moire interferometry, the horizontal and vertical displacement fields （u and v） can be obtained to determinate two strain fields and one shearing strain field. In this paper, by means of Moire interferometry and three directions grating （grating rosette） developed by the authors, three displacement fields （u, v and s） are obtained to acquire three strain fields. As a practical application, the hole-drilling method is adopted to measure the relief strains for aluminum and fiber reinforced composite. It is a step by step method; in each step a single laminate or equivalent depth is drilled to find some relationships between the drilling depth and the residual strains relieved in the fiber reinforced composite materials.

Residual Stress Measurement for Ion-implanted NiTi Alloy by Using Moiré Interferometry and Hole-drilling Combined Method

Residual stresses in ion-implanted NiTi alloy are measured by a combined method ofMoir6 interferometry and hole-drilling. Oxygen ions are implanted into the NiTi alloy under a voltage of 30 kV by a dose of 1.0×10^17ions/cm^2 for one hour. Subsequently, in order to avoid dimensional error, a hole is drilled exactly in the center of the sample. The distribution of residual stresses around the hole is measured. It is indicated that the method which combines the Moire interferometry with hole-drilling is able to be used to measure residual stresses produced by ion implantation.

Study on Plasticity Modification for Measuring High Residual Stress by Hole-Drilling Method

Hole-drilling method is a commonly used method for measuring residual stress. The calibration coefficients in ASTM E837-13 a would cause large errors due to the plasticity deformation of materials. In the study, calibration coefficients were modified in the plasticity deformation stage based on the distortion energy theory. The calibration experiment of calibration coefficients was simulated by the finite element model, and the plasticity modification formulas of 7075 aluminum alloy were obtained. From the results of uniaxial tensile loading test, the measuring errors of high residual stress are significantly reduced from-4.071%～53.440% to-5.140% ～ 0.609% after the plasticity modification. This work provides an effective way to expand the application of hole-drilling method.

Residual stress evolution regularity in thermal barrier coatings under thermal shock loading

Residual stress evolution regularity in thermal barrier ceramic coatings （TBCs） under different cycles of thermal shock loading of 1 100℃ was investi- gated by the microscopic digital image correlation （DIC） and micro-Raman spec- troscopy, respectively. The obtained results showed that, as the cycle number of the thermal shock loading increases, the evolution of the residual stress under- goes three distinct stages： a sharp increase, a gradual change, and a reduction. The extension stress near the TBC surface is fast transformed to compressive one through just one thermal cycle. After different thermal shock cycles with peak temperature of 1 100℃, phase transformation in TBC does not happen, whereas the generation, development, evolution of the thermally grown oxide （TGO） layer and micro-cracks are the main reasons causing the evolution regularity of the residual stress.

Residual strain evaluation of curved surface by grating-transferring technique and GPA

This paper investigates an advanced grating-transferring technique combined with geometric phase analysis (GPA) for residual strain evaluation of curved surface.A standard holographic grating is first transferred to a pre-produced epoxy resin film and then consolidated to a test region of curved surface.With a rubber mold and silicone rubber the deformed grating is replicated to a sheet metal after hole-drilling for release of residual stress.After that the grating is transferred from the sheet metal to the glass plate,which would be served as an analyzer grating (specimen grating).By GPA the local strain distributions related to the phase difference between the reference grating and analyzer grating for the released stress can be evaluated.A validation test has been conducted on the weld joint of a stainless steel tube and the obtained results demonstrate the ability of the method in measuring the residual strain of curved surface.