Effect of La_2O_3 on microstructure and high-temperature wear property of hot-press sintering FeAl intermetallic compound

FeAl intermetallic compound with different contents of rare earth oxide La2O3 addition was prepared by hot pressing the mechanically alloyed powders.Effect of La2O3 on microstructure and high-temperature wear property of the sintered FeAl samples was investigated in this paper.The results showed that 1 wt.% La2O3 addition could refine the microstructure and increase the density of the FeAl intermetallic compound,and correspondingly improved the high-temperature wear resistance.SEM and EDS analyses of the wo...

Sintering zone prediction in direct metal laser sintering by finite element method

A three-dimensional finite element thermal model in direct metal laser sintering(DMLS) including the effect of powder-to-solid transition were established to predict sintering zone, which benefited the determination of suitable process parameters in DMLS. The nonlinear transient model of the metals thermal conductivity for powder-to-solid transition was developed. The model uses solid thermal properties of material in liquid-phase zone, transitional ones in sintering or sintered zone and powder ones in unsintered zones of powder bed to predict, respectively. Sintering zone boundary was estimated by maximum temperature history profile. Experiments were carried out using multi-component Cu-based metal powder. Compared experimental and predicted results, the mean error of sintering depth and width are 7.8% and 14.4%, respectively, which confirms the accuracy of the FEM prediction.

Effects of various sintering methods on microstructure and mechanical properties of CP-Ti powder consolidations

Effects of various sintering methods such as spark plasma sintering(SPS), hot pressing(HP) and electric resistance sintering(ERS) on the microstructure and mechanical properties of commercial pure titanium(CP-Ti) powder consolidations with particle size of <147 μm, <74 μm and <43 μm were studied. The smaller particle powders are densified to proceed at a higher rate. Dense titanium with relative density up to 99% is found to take place at 850 °C under 30 MPa of SPS and HP condition. However, in case of ERS, CP-Ti powders were densified almost at 950 °C under 30 MPa. The microstructure of sintered titanium is composed of equiaxed grains at 850-950 °C. The yield strength of sintered body composed of <43 μm powder is 858 MPa by using SPS at 850 °C under 30 MPa. When there is a higher content of small particle, the higher yield strength value is obtained both by using SPS and HP. However, when ERS is introduced, the highest yield strength is 441 MPa at 950 °C under 30 MPa, which shows much lower values than those by SPS and HP methods. ERS method takes much less sintering time compared with SPS and HP. Nevertheless, higher sintering temperature results in lower strength and elongation because of brittle fracture.

Finite-Element Simulation and Experimental Research of the Hot-Press Sintering of Nano-Sized Ceramic Powders

Numerical simulation of hot-press sintering of nano-sized ceramic powders was introduced by the commercial finite element code MSC.MARC. The powder plastic model and the thermo-mechanical coupled quadrilateral element were developed and adopted in the simulation. The mechanical and thermal properties of the nano-sized alumina based powders were determined.In addition, the experimental research and numerical simulation of the sintering process of different initial densities were carried out. The stress state in sintering of green compacts with different initial densities was analyzed by the densification theory.The reason for the density fluctuations of as-sintered ceramic bulks was found out.

Reactive Hot-press Sintering of Al-B_4C Composites at Relative Low Temperature

A new process of reactive hot-press sintering with boron carbide(B4C) and aluminum powders was proposed to overcome difficulties in the sintering of dense B4C ceramic materials.The B4C powder with different content of pure metallic aluminum particle were milled,hot-pressed and sintered at 1600 ℃ for 1 hour.The mechanism of sintering at relative low temperature was analyzed.The phase constitution of the composites was determined.Effects of Al content on the hardness and fracture toughness of the composites were discussed.The results show that thermite reaction procedure in B2O3+Al was the mechanism of sintering at relative low temperature,B4C,Al2O3 and metallic aluminum are the major constituents of the composites.The microhardness of the composites decreases with the increasing of Al content,but the fracture toughness increase obviously.The composite with 5wt% Al content has the best microhardness and fracture toughness in all the composites.

UPPER BOUND METHOD FOR SINTERED POWDER MATERIALS IN PLANE STRAIN

ＵＰＰＥＲＢＯＵＮＤＭＥＴＨＯＤＦＯＲＳＩＮＴＥＲＥＤＰＯＷＤＥＲＭＡＴＥＲＩＡＬＳＩＮＰＬＡＮＥＳＴＲＡＩＮＵＰＰＥＲＢＯＵＮＤＭＥＴＨＯＤＦＯＲＳＩＮＴＥＲＥＤＰＯＷＤＥＲＭＡＴＥＲＩＡＬＳＩＮＰＬＡＮＥＳＴＲＡＩＮ￥Ｈｕａ，ＬｉｎＺｈａｏ，Ｚｈ...

Dielectric properties of spark plasma sintering AlN-W composite ceramics

In order to develop AlN composites suitable for high average power electronic tube, AlN-W materials were prepared by spark plasma sintering. The effects of manufacture parameters on dielectric loss tangent and permittivity constant were investigated, which include powder-mixed method, milling time of high-energy ball milling, starting powder particle size, sintering temperature and holding time and adding amount of the conductive second phase. The results showed that A1N-W materials sintered at the temperature of 1700℃ holding for 5 min with 10 vol.% W showed the best dielectric loss tangent larger than 0.81 at the frequency 1 kHz-1 MHz. In addition, magnetic stirring mixed powder and lower sintering temperature led to the better propelties because of the higher porosity. The samples sintered from the starting AlN powder with smaller particle size also had the better properties.

High-pressure Sintering of Boron Carbide-Titanium Diboride Composites and Its Densification Mechanism

A high-pressure hot-pressing process was applied to densify a commercial boron carbide-titanium diboride (B4C-TiB2) powder mixture.Nearly fully dense (98.6%) materials were obtained at 1700℃ under a pressure of 100MPa.Compared to the sintering temperature required to achieve similar results when a pressure of only 30MPa was applied,the sintering temperature was found to decrease by about 200℃ under pressure of 100 MPa.Analysis of the thermodynamics and microstructure showed that the plastic deformation of the B4C grains induced by high pressure dominated the densification mechanism when high pressure was applied.Furthermore,higher pressure resulted in remarkably improved mechanical properties of the composites,which could be traced back to the generation of stacking faults in the B4C grains and aggregation of TiB2.

The effect of agglomerate on micro-structural evolution in solid-state sintering

Discrete element method （DEM） is used in the present paper to simulate the microstructural evolution of a planar layer of copper particles during sintering. Formation of agglomerates and the effect of their rearrangement on densification are mainly focused on. Comparing to the existing experimental observations, we find that agglomerate can form spontaneously in sintering and its rearrangement could accelerate the densification of compacts. Snapshots of numerical simulations agree qualitatively well with experimental observations. The method could be readily extended to investigate the effect of agglomerate on sintering in a three- dimensional model, which should be very useful for understanding the evolution of microstructure of sintering systems.

SLIP LINE METHOD FOR SINTERED POWDER MATERIALS UNDER CONDITION OF AXIAL SYMMETRY DEFORMATION

Slip line method for sintered powder materials under condition of axial symmetry is proposed based on the simplified yield condition of sintered powder materials and Haar-von Karman perfect plastic criterion. The equations of slip line and stress along slip line are derived, and numerical solutions are given. Deformation load in closed die upsetting of sintered copper cylinder is calculated by slip line method, and theoretical solutions are compared with experimental results.

Influences of Sintering Process of Sprayed Precursors on the Struc-ture and Electrochemical Properties of LiMn_2O_4 Cathode Material

Well-defined spinel LiMn2O4 powders were synthesized via sintering a precursor, which was prepared by spraydrying method. The effects of sintering process on the structure and electrochemical properties of LiMn2O4 were discussed. It was found that a single sintering could not synthesize a pure LiMn2O4 compound, while two-step sintering procedure consisting of decomposing sprayed precursors at 350℃ and further sintering at an elevated temperature leads to the formation of a single-phased LiMn2O4 with homogeneous particle size distribution. As compared to that sintered in air, the two-step sintered LiMn2O4 in oxygen shows tighter structure and more uniform particle size, as well as better electrochemical properties. It delivers an initial discharge capacity of 131 mAh·g^-1 （1/10C）, and still has excellent cycling stability at higher rate （1/5C）.

Preparation of coated sand for selective laser sintering and optimization of baking process of sand moulds

A cold method was used to prepare coated sand for application in the selective laser sintering(SLS)process.Tensile strength,loss on ignition,gas evolution,and accuracy of the SLS samples were tested and analyzed,and the baking process was thoroughly investigated.Compared with coated sand prepared by the hot method,the cold method yields a more uniform and complete resin film on the sand's surface,resulting in enhanced tensile strength and accuracy.Additionally,the cold method requires a lower binder content to meet the same strength requirements,thereby minimizing gas evolution,reducing porosity defects,and ultimately improving casting quality.The coated sand samples prepared through the cold method exhibit superior accuracy,with a size error of within±0.4 mm.In contrast,the coated sand samples prepared by the hot method display a lower accuracy,with an average negative error of 2.1993 mm.The highest tensile strength could be attained by controlling the baking temperature within a suitable range(180-190°C),which can effectively reduce the generation of gas,thus contributing to improved overall performance.

Sintering Densification of Boron Carbide Materials and Their Research Progress

Boron carbide(B_(4)C)has excellent high-temperature oxidation resistance,high hardness,low relative density,high melting point and excellent abrasive resistance,which is widely used in fields such as refractories,wear-resistant materials and lightweight protective materials.The research progress and application of B_(4)C materials in China and overseas in recent years were summarized.The influences of sintering processes(pressureless sintering,hot-pressing sintering,hot isostatic pressing sintering,spark plasma sintering and microwave sintering)and sintering additives(simple substances,oxides and carbides)on the B_(4)C densification were analyzed.The development of B_(4)C materials was prospected.

Finite element method simulation for tensile process of sintered iron-base material

Different material properties leads to different metal fracture behaviors. Even if the powder material is composed of plastic metal, the fracture still does not show macroscopic plastic deformation characteristics if the material contains a large number of voids. Eight node isoparametric elastic plastic finite element method was used to simulate the tensile process of sintered powder material. By setting a number of voids in the analyzed metal cuboid, the initial density was taken into consideration. The material properties of the three dimensional solid for the tensile simulation were defined with reference to the known pure iron material parameters. The load displacement curves during elongation were obtained with a universal testing machine, and then the simulated curves were compared with the experimental results. The factors that cause the stress concentration and strength decrease were analyzed according to the simulated equivalent von Mises stress distribution.

Distinct Electrical and Mechanical Responses of a Cu-10Fe Composite Prepared by Hot-Pressed Sintering and Post Treatment

A Cu-10wt%Fe composite was prepared through hot-pressed sintering,and the material was subsequently solution treated.The hot-pressed sintered and solution treated materials were rolled and aged.The precipitation behavior and performance changes were systematically studied by using scanning electron microscopy and transmission electron microscopy.In contrast to the hot-pressed sintered specimen,the solution treatment significantly affects the thermal stability and properties of the Cu-10wt%Fe composite.The Cu-10wt%Fe composite was prepared after solid solution,cold rolling and aging at 773 K for 1 h,and it obtained excellent tensile strength of 494 MPa,uniform elongation of 16.3%,electrical conductivity of 51.1%IACS and softening temperature of 838 K.Mechanisms for the distinct difference in thermal stability and properties between hot-pressed sintered and solution treated specimens were analyzed.These findings provide a theoretical basis for designing high-performance Cu-based in-situ composites by post treatment.

Preparation of Fe-As alloys by mechanical alloying and vacuum hot-pressed sintering:microstructure evolution,mechanical properties,and mechanisms

Arsenic materials have attracted great attention due to their unique properties.However,research concerning iron-arsenic(Fe-As) alloys is very scarce due to the volatility of As at low temperature and the high melting point of Fe.Herein,a new Fe-As alloy was obtained by mechanical alloying(MA) followed by vacuum hot-pressed sintering(VHPS).Moreover,a systematic study was carried out on the microstructural evolution,phase composition,leaching toxicity of As,and physical and mechanical properties of Fe-As alloys with varying weight fractions of As(20%,25%,30%,35%,45%,55%,65%,and 75%).The results showed that pre-alloyed metallic powders(PAMPs) have a fine grain size and specific supersaturated solid solution after MA,which could effectively improve the mechanical properties of Fe-As alloys by VHPS.A high density(> 7.350 g·cm^(-3)),low toxicity,and excellent mechanical properties could be obtained for FeAs alloys sintered via VHPS by adding an appropriate amount of As,which is more valuable than commercial Fe-As products.The Fe-25% As alloy with low toxicity and a relatively high density(7.635 g·cm^(-3)) provides an ultra-high compressive strength(1989.19 MPa),while the Fe-65% As alloy owns the maximum Vickers hardness(HVo.5 899.41).After leaching by the toxicity characteristic leaching procedure(TCLP),these alloys could still maintain good mechanical performance,and the strengthening mechanisms of Fe-As alloys before and after leaching were clarified.Changes in the grain size,micro structure,and phase distribution induced significant differences in the compressive strength and hardness.

Recycle for Sludge Scrap of Nd-Fe-B Sintered Magnet as Isotropic Bonded Magnet

The reduction diffusion method was performed for the sludge scrap of Nd-Fe-B sintered magnets with adding Ca metal to recover the oxidized Nd-Fe-B phase. After washing the resultant powders to remove Ca metal component, the powders obtained were recycled as an isotropic magnetic powder by the melt spinning method. The magnetic properties of powders as recycled were inferior, especially for the coercivity value, due to the deletion of rare earth metals during the washing process. The adjustment of metal composition, i.e., the addition of Nd metal, at the melt spinning process improved the magnetic properties to be B r=～0.75 T, H cj=～0.93 mA·m -1, and (BH) max=～91 kJ·m -3. The magnetic properties of the bonded magnets prepared from the composition-adjusted powders were B r=～0.66 T, H cj=～0.92 mA·m -1, and (BH) max=～70 kJ·m -3, which are approximately comparable to the commercially available MQPB boned one (B r=～0.73 T, H cj=～0.79 mA·m -1, and (BH) max=～86 kJ·m -3).

Repetitious-Hot-Pressing Technique in Hot-Pressing Process

A new pressing method was proposed for hot-pressing process. Experimental results indicated that the porosity in Al2O3/TiC/ Ni/Mo (hereafter called AI2O3/TiC composite) composite compacts decreases by 6% after adopting this new technique, compared to traditional hot-pressing technique under the same sintering temperature. The flexural strength and Vicker hardness increase from 883 MPa to 980 MPa and from 16 GPa to 21.1 GPa, respectively. A theoretical model was given to analyze the densification mechanism of the composite in the process of repetitious-hot-pressing.

Effect of nitrogen introduction methods on the microstructure and properties of gradient cemented carbides

Gradient cemented carbides with the surface depleted in cubic phases were prepared following normal powder metallurgical pro-cedures.Gradient zone formation and the influence of nitrogen introduction methods on the microstructure and performance of the alloys were investigated.The results show that the simple one-step vacuum sintering technique is doable for producing gradient cemented carbides.Gradient structure formation is attributed to the gradient in nitrogen activity during sintering,but is independent from nitrogen introduced methods.A uniform carbon distribution is found throughout the materials.Moreover,the transverse rupture strength of the cemented carbides can be increased by a gradient layer.Different nitrogen carriers give the alloys distinguishing microstructure and mechanical properties,and a gradient alloy with ultrafine-TiC0.5N0.5 is found optimal.

Characterization of YSZ Ceramic Nanopowders Synthesized at Different Temperatures via Polyacrylamide Gel Method

Tetragonal zirconia (T-ZrO2) ceramic nanopowders stabilized with 3 mol% Y2O3 were synthesized via polyacrylamide gel method, using ZrOCl2?8H2O and Y(NO3)3?6H2O as raw materials. The effect of temperature on phase composition and morphology of YSZ nanopowders and sintering behavior of YSZ ceramics was investigated by X-ray diffraction (XRD), scanning electron microscopy (SEM) and Vickers hardness tester. The aging-resistance of YSZ ceramics was measured by means of aging experiments. The results demonstrated that the phase composition of YSZ ceramic nanopowders had no obvious change and it was composed of T-ZrO2. Particle size of well-dispersed YSZ ceramic nanopowders increased from 17 to 35 nm with increasing calcining temperature from 600 to 800 ℃. There was noticeable negative correlation between calcining temperature and the relative density of YSZ ceramic at the same sintering temperature. The aging experiments showed that water vapor facilitated tetragonal to monoclinic phase transformation, and the sample that had smaller grain size exhibited better aging-resistance. It can be concluded that when the calcining temperature is 600 ℃ and sintering temperature is 1550 ℃, the relative density and hardness of YSZ ceramic arrive at the peak of 96.64% and 11.135 GPa respectively, and it has less microcracks and excellent aging-resistance.