Effect of thermo-mechanical treatment on microstructure and mechanical properties of wire-arc additively manufactured Al-Cu alloy

Wire-arc additive manufacture(WAAM)has great potential for manufacturing of Al-Cu components.However,inferior mechanical properties of WAAM deposited material restrict its industrial application.Inter-layer cold rolling and thermo-mechanical heat treatment(T8)with pre-stretching deformation between solution and aging treatment were adopted in this study.Their effects on hardness,mechanical properties and microstructure were analyzed and compared to the conventional heat treatment(T6).The results show that cold rolling increases the hardness and strengths,which further increase with T8 treatment.The ultimate tensile strength(UTS)of 513 MPa and yield stress(YS)of 413 MPa can be obtained in the inter-layer cold-rolled sample with T8 treatment,which is much higher than that in the as-deposited samples.The cold-rolled samples show higher elongation than that of as-deposited ones due to significant elimination of porosity in cold rolling;while both the T6 and T8 treatments decrease the elongation.The cold rolling and pre-stretching deformation both contribute to the formation of dense and dispersive precipitatedθ′phases,which inhibits the dislocation movement and enhances the strengths;as a result,T8 treatment shows better strengthening effect than the T6 treatment.The strengthening mechanism was analyzed and it was mainly related to work hardening and precipitation strengthening.

Customized heat treatment process enabled excellent mechanical properties in wire arc additively manufactured Mg-RE-Zn-Zr alloys

Customized heat treatment is essential for enhancing the mechanical properties of additively manufactured metallic materials,especially for alloys with complex phase constituents and heterogenous microstructure.However,the interrelated evolutions of different microstructure features make it difficult to establish optimal heat treatment processes.Herein,we proposed a method for customized heat treatment process exploration and establishment to overcome this challenge for such kind of alloys,and a wire arc additively manufactured(WAAM)Mg-Gd-Y-Zn-Zr alloy with layered heterostructure was used for feasibility verification.Through this method,the optimal microstructures(fine grain,controllable amount of long period stacking ordered(LPSO)structure and nano-scaleβ'precipitates)and the corresponding customized heat treatment processes(520°C/30 min+200°C/48 h)were obtained to achieve a good combination of a high strength of 364 MPa and a considerable elongation of 6.2%,which surpassed those of other state-of-the-art WAAM-processed Mg alloys.Furthermore,we evidenced that the favorable effect of the undeformed LPSO structures on the mechanical properties was emphasized only when the nano-scaleβ'precipitates were present.It is believed that the findings promote the application of magnesium alloy workpieces and help to establish customized heat treatment processes for additively manufactured materials.

Mechanical behavior and response mechanism of porous metal structures manufactured by laser powder bed fusion under compressive loading

Al Si10Mg porous protective structure often produces different damage forms under compressive loading,and these damage modes affect its protective function.In order to well meet the service requirements,there is an urgent need to comprehensively understand the mechanical behavior and response mechanism of AlSi10Mg porous structures under compressive loading.In this paper,Al Si10Mg porous structures with three kinds of volume fractions are designed and optimized to meet the requirements of high-impact,strong-energy absorption,and lightweight characteristics.The mechanical behaviors of AlSi10Mg porous structures,including the stress-strain relationship,structural bearing state,deformation and damage modes,and energy absorption characteristics,were obtained through experimental studies at different loading rates.The damage pattern of the damage section indicates that AlSi10Mg porous structures have both ductile and brittle mechanical properties.Numerical simulation studies show that the AlSi10Mg porous structure undergoes shear damage due to relative misalignment along the diagonal cross-section,and the damage location is almost at 45°to the load direction,which is the most direct cause of its structural damage,revealing the damage mechanism of AlSi10Mg porous structures under the compressive load.The normalized energy absorption model constructed in the paper well interprets the energy absorption state of Al Si10Mg porous structures and gives the sensitive location of the structures,and the results of this paper provide important references for peers in structural design and optimization.

Characterization and Modeling of Mechanical Properties of Additively Manufactured Coconut Fiber-Reinforced Polypropylene Composites

In the face of the increased global campaign to minimize the emission of greenhouse gases and the need for sustainability in manufacturing, there is a great deal of research focusing on environmentally benign and renewable materials as a substitute for synthetic and petroleum-based products. Natural fiber-reinforced polymeric composites have recently been proposed as a viable alternative to synthetic materials. The current work investigates the suitability of coconut fiber-reinforced polypropylene as a structural material. The coconut fiber-reinforced polypropylene composites were developed. Samples of coconut fiber/polypropylene (PP) composites were prepared using Fused Filament Fabrication (FFF). Tests were then conducted on the mechanical properties of the composites for different proportions of coconut fibers. The results obtained indicate that the composites loaded with 2 wt% exhibited the highest tensile and flexural strength, while the ones loaded with 3 wt% had the highest compression strength. The ultimate tensile and flexural strength at 2 wt% were determined to be 34.13 MPa and 70.47 MPa respectively. The compression strength at 3 wt% was found to be 37.88 MPa. Compared to pure polypropylene, the addition of coconut fibers increased the tensile, flexural, and compression strength of the composite. In the study, an artificial neural network model was proposed to predict the mechanical properties of polymeric composites based on the proportion of fibers. The model was found to predict data with high accuracy.

The design, manufacture and application of multistable mechanical metamaterials-a state-of-the-art review

Multistable mechanical metamaterials are a type of mechanical metamaterials with special features,such as reusability,energy storage and absorption capabilities,rapid deformation,and amplified output forces.These metamaterials are usually realized by series and/or parallel of bistable units.They can exhibit multiple stable configurations under external loads and can be switched reversely among each other,thereby realizing the reusability of mechanical metamaterials and offering broad engineering applications.This paper reviews the latest research progress in the design strategy,manufacture and application of multistable mechanical metamaterials.We divide bistable structures into three categories based on their basic element types and provide the criterion of their bistability.Various manufacturing techniques to fabricate these multistable mechanical metamaterials are introduced,including mold casting,cutting,folding and three-dimensional/4D printing.Furthermore,the prospects of multistable mechanical metamaterials for applications in soft driving,mechanical computing,energy absorption and wave controlling are discussed.Finally,this paper highlights possible challenges and opportunities for future investigations.The review aims to provide insights into the research and development of multistable mechanical metamaterials.

Microstructure and Mechanical Properties of Wire + Arc Additively Manufactured 2050 Al–Li Alloy Wall Deposits

Aluminum–Lithium(Al–Li) alloy is a topic of great interest owing to its high strength and light weight, but there are only a few applications of Al–Li alloy in wire ss, a special AA2050 Al–Li alloy + arc additive manufacturing(WAAM) process. To identify its feasibility in WAAM procewire was produced and employed in the production of straight-walled components, using a WAAM system based on variable polarity gas tungsten arc welding(VP-GTAW) process. The influence of post-deposited heat treatment on the microstructure and property of the deposit was investigated using optical micrographs(OM), scanning electron microscopy(SEM), X-ray diffraction(XRD), hardness and tensile properties tests. Results revealed that the microstructures of AA2050 aluminum deposits varied with their location layers. The upper layers consisted of fine equiaxed grains, while the bottom layer exhibited a coarse columnar structure. Mechanical properties witnessed a significant improvement after post-deposited heat treatment, with the average micro-hardness reaching 141 HV and the ultimate tensile strength exceeding 400 MPa. Fracture morphology exhibited a typical ductile fracture.

Formability,microstructure evolution and mechanical properties of wire arc additively manufactured AZ80M magnesium alloy using gas tungsten arc welding

Wire arc additive manufacturing(WAAM)technology has been used to fabricate the multi-layer single-pass deposited wall of AZ80M magnesium(Mg)alloy by gas tungsten arc welding.The formability,thermal cycles,microstructural evolution and mechanical properties of the WAAM AZ80M Mg alloy were investigated.The results show that there was significant difference in the temperature variation and the geometries between the original several layers and the subsequent deposited layers.Owing to the arc energy input,the interpass temperature rised rapidly and then stabilized at 150℃.As a result,the width of the deposited wall increased and then kept stable.There were obvious differences in the microstructure of the WAAM AZ80M Mg alloy among the top zone,intermediate zone and bottom zone of deposited wall.During the arc deposition process,theβphase of the WAAM AZ80M Mg alloy redissolved due to the cyclic heat accumulation,and then precipitated in the grain boundary.The cyclic heat accumulation also led to weakening of dendrite segregation.From the substrate to the top zone,the hardness of the deposited wall decreased gradually,and the intermediate zone which was the main body of deposited wall had relatively uniform hardness.The tensile properties of the WAAM AZ80M Mg alloy were different between the vertical direction and the horizontal direction.And the maximum ultimate tensile strength of the WAAM AZ80M Mg alloy was 308 MPa which was close to that of the as-extruded AZ80M Mg alloy.

Mechanical property and biological behaviour of additive manufactured TiNi functionally graded lattice structure

Bio-inspired porous metallic scaffolds have tremendous potential to be used as artificial bone substitutes.In this work,a radially graded lattice structure (RGLS),which mimics the structures of natural human bones,was designed and processed by laser powder bed fusion of martensitic Ti-rich TiNi powder.The asymmetric tension-compression behaviour,where the compressive strength is significantly higher than the tensile strength,is observed in this Ti-rich TiNi material,which echoes the mechanical behaviour of bones.The morphologies,mechanical properties,deformation behaviour,and biological compatibility of RGLS samples were characterised and compared with those in the uniform lattice structure.Both the uniform and RGLS samples achieve a relative density higher than 99%.The graded porosities and pore sizes in the RGLS range from 40%-80% and 330-805 µm,respectively,from the centre to the edge.The chemical etching has significantly removed the harmful partially-melted residual powder particles on the lattice struts.The compressive yield strength of RGLS is 71.5 MPa,much higher than that of the uniform sample (46.5 MPa),despite having a similar relative density of about 46%.The calculated Gibson-Ashby equation and the deformation behaviour simulation by finite element suggest that the dense outer regions with high load-bearing capability could sustain high applied stress,improving the overall strength of RGLS significantly.The cell proliferation study suggests better biological compatibility of the RGLS than the uniform structures.The findings highlight a novel strategy to improve the performance of additively manufactured artificial implants by bio-inspiration.

Microstructures and mechanical properties of Ti−Al−V−Nb alloys with cluster formula manufactured by laser additive manufacturing

Ti−Al−V−Nb alloys with the cluster formula,12[Al−Ti_(12)](AlTi_(2))+5[Al−Ti1_(4)](V,Nb)2Ti,were designed by replacing V with Nb based on the Ti−6Al−4V alloy.Single-track cladding layers and bulk samples of the alloys with Nb contents ranging from 0 to 6.96 wt.%were prepared by laser additive manufacturing to examine their formability,microstructure,and mechanical properties.For single-track cladding layers,the addition of Nb increased the surface roughness slightly and decreased the molten pool height to improve its spreadability.The alloy,Ti−5.96Al−1.94V−3.54Nb(wt.%),exhibited better geometrical accuracy than the other alloys because its molten pool height was consistent with the spread layer thickness of the powder.The microstructures of the bulk samples contained similar columnar β-phase grains,regardless of Nb content.These grains grew epitaxially from the Ti substrate along the deposition direction,with basket-weaveα-phase laths within the columnar grains.Theα-phase size increased with increasing Nb contents,but its uniformity decreased.Along the deposition direction,the Vickers hardness increased from the substrate to the surface.The Ti−5.96Al−1.94V−3.54Nb alloy exhibited the highest Vickers hardness regardless of deposition position because of the optimal matching relationship between theα-phase size and its content among the designed alloys.

Microstructure and mechanical property of additively manufactured NiTi alloys:A comparison between selective laser melting and directed energy deposition

NiTi shape memory alloy(SMA)with nominal composition of Ni 50.8 at%and Ti 49.2 at%was additively manufactured(AM)by selective laser melting(SLM)and laser directed energy deposition(DED)for a comparison study,with emphasis on its phase composition,microstructure,mechanical property and deformation mechanism.The results show that the yield strength and ductility obtained by SLM are 100 MPa and 8%,respectively,which are remarkably different from DED result with 700 MPa and 2%.The load path of SLM sample presents shape memory effect,corresponding to martensite phase detected by XRD;while the load path of DED presents pseudo-elasticity with austenite phase.In SLM sample,fine grain and hole provide a uniform deformation during tensile test,resulting in a better elongation.Furthermore,the nonequilibrium solidification was studied by a temperature field simulation to understand the difference of the two 3D printing methods.Both temperature gradient G and growth rate R determine the microstructure and phase in the SLM sample and DED sample,which leads to similar grain morphologies because of similar G/R.While higher G×R of SLM leads to a finer grain size in SLM sample,providing enough driving force for martensite transition and subsequently changing texture compared to DED sample.

Microstructure evolution and mechanical properties of laser additive manufactured Ti-5Al-2Sn-2Zr-4Mo-4Cr alloy

The microstructure, microhardness and tensile properties of laser additive manufactured (LAM) Ti?5Al?2Sn?2Zr?4Mo?4Cr alloy were investigated. The result shows that the microstructure evolution is strongly affected by the thermal history of LAM process. Primary α (αp) with different morphologies, secondary α (αs) and martensite α' can be observed at different positions of the LAMed specimen. Annealing treatment can promote the precipitation of rib-like α phase or acicular α phase. As a result, it can increase or decrease the microhardness. The as-deposited L-direction and T-direction specimens contain the same phase constituent with different morphologies. The tensile properties of the as-deposited LAMed specimens are characterized of anisotropy. The L-direction specimen shows the character of low strength but high ductility when compared with the T-direction specimen. After annealing treatment, the strength of L-direction specimen increases significantly while the ductility reduces. The strength of the annealed T-direction specimen changes little, however, the ductility reduces nearly by 50%.

Production Decision Based on Discounted Price and Delivery Frequency for Garment Original Equipment Manufacturer with Constrained Capacity

Original equipment manufacturers(OEM) have never been so important and powerful as it is today in garment manufacturing industry.The OEMsupplier's production decisions always have a great impact on the market performance and the profits of a garment brand manufacturer.With constrained capacity and multiply buyers,howto make reasonable production decisions is an urgent problem for OEMsuppliers.A price discount model with a single OEMsupplier and two buyers is proposed to deal with the problem.Based on this model,the OEMsupplier could satisfy buyers' demands and guarantee their profits as well through adjusting price and delivery frequency.A numerical example validates the validity of the model.

Zibo Sangde Machinery Equipment Co., Ltd The Most Professional Manufacturer of Refractory Electric Screw Press in China

Zibo Sangde Machinery Equipment Co., Ltd. is the first Manufacturer of Refractory Electric Screw Press in China, in the year of 2008, our company produced the first set 315T Refractory Electric Program-controlled Screw Press in China, which is no friction discs, simple structure, with PLC controlling the brick forming process, no need special operator. Once upon the Press was on the market, it achieved a strong interests and reputations from many Refractory Factories because of its Highefficient, Energy-saving（can save by 40-50% electricity comparing to the Friction Press）, manpower reduction and improving the quality of bricks.

ZTE Named“World's Best CDMA Equipment Manufacturer 2009”

ZTE Corporation announced on November 6, 2009 that the company has received the prestigious "World’s Best CDMA Equipment Manufacturer 2009" award from research and consulting firm Frost & Sullivan.

Practice Teaching Reform of Mechanical Design and Manufacture and Its Automation Specialty under Transformation and Development

With the development of the times, undergraduate colleges and universities begin to transform and develop to adapt to the changing society, and put forward new requirements for practical teaching strategies, especially for applied undergraduate colleges. The reform of practical teaching is particularly important. Under the development of education transformation, the reform of mechanical design and manufacture and the practice teaching of automation specialty also occupy a very important position. Through the understanding of the reform of the practical teaching of this specialty, the effect of the reform is observed, and a reasonable teaching scheme is put forward to promote the steps of the transformation of the practical teaching.

Manufacture and Export of Complete Power Equipment

Through construction during over four decades, remarkable achievements have been made by China’s manufacturing industry of complete sets of power equipment. During the Seventh Five-Year Plan period, over RMB2 billion and several hundred million US dollars were invested in the introduction

The Analysis of Logistics Strategic Type of Northeastern Equipment Manufacture Industry

Logistics strategy has very important function to the development of old industrial base of equipment manufacture industry in the northeast, logistics strategic type is an important component of logistics strategy. The understanding of it will contributes to enterprise make suitable logistics strategy according to one＇s own actual conditions, to plan long-term development, and then establish an unassailable position during keen competition nowadays.

The Condition of Fostering Core Competitiveness of Equipment Manufacture Industry in Our Country

The equipment manufacture industry occupies the important position in our national economy, and the research on its core competitiveness is an important aspect of protecting the healthy development of equipment manufacture industry. Researches on core competitiveness of equipment manufacture industry are to cultivate, strengthen and perfect enterprise＇s core competitiveness and bring about the advance to enterprise.

How Many Indigenous Manufacturers Working on UHV Equipment

Since the year 2006, having been trained in EHV power grid construction, indigenous manufacturing companies have gradually become full-fledged. With the advancement of the UHV program, they become more confident. Among these companies, there are Xi'an Shiky High Voltage Electric Co., Ltd.(Shiky) of China XD Group(XD), a mega state-owned enterprise, Tebian Electric Apparatus Stock Co., Ltd. (TBEA), a stock company, as well as Baoding Tianwei Baobian Electric Co., Ltd. (TWBB), a dark horse among private sectors. Moreover, Shanghai Sieyuan Electric Co., Ltd.(Sieyuan), which is especially mentionable, has attracted more attention in the industry for its outstanding and rapidly rising market performance.

Hall-Petch relationship in selective laser melting additively manufactured metals:using grain or cell size?

The mechanical properties of many materials prepared by additive manufacturing technology have been greatly improved.High strength is attributed to grain refinement,formation of high density dislocation and existence of cellular structures with nanoscale during manufacturing.In addition,the super-saturated solid solution of elements in the matrix and the solid solution segregation along the wall of the cellular structures also promote the improvement of strength by enhancing dislocation pinning.Hence,the existence of cellular structure in grains leads to differences in the prediction of material strength by Hall-Petch relationship,and there is no unified calculation method to determine the d value as grain size or cell size.In this work,representative materials including austenite 316L SS were printed by selective laser melting(SLM),and the strength was predicted.The values of cell size and grain size were substituted into Hall-Petch formula,and the results showed that the calculation error for 316L is increased from 4.1%to 11.9%.Therefore,it is concluded that the strength predicted by grain size is more accurate than that predicted by cell size in additive manufacturing materials.When calculating the yield strength of laser additive manufacturing metal materials through the Hall-Petch formula,the grain size should be used as the basis for calculation.