Simulation and analysis of humid air turbine cycle based on aeroderivative three-shaft gas turbine

Due to the fact that the turbine outlet temperature of aeroderivative three-shaft gas turbine is low,the conventional combined cycle is not suitable for three-shaft gas turbines.However,the humid air turbine(HAT)cycle provides a new choice for aeroderivative gas turbine because the humidification process does not require high temperature.Existing HAT cycle plants are all based on single-shaft gas turbines due to their simple structures,therefore converting aeroderivative three-shaft gas turbine into HAT cycle still lacks sufficient research.This paper proposes a HAT cycle model on a basis of an aeroderivative three-shaft gas turbine.Detailed HAT cycle modelling of saturator,gas turbine and heat exchanger are carried out based on the modular modeling method.The models are verified by simulations on the aeroderivative three-shaft gas turbine.Simulation results show that the studied gas turbine with original size and characteristics could not reach the original turbine inlet temperature because of the introduction of water.However,the efficiency still increases by 0.16%when the HAT cycle runs at the designed power of the simple cycle.Furthermore,simulations considering turbine modifications show that the efficiency could be significantly improved.The results obtained in the paper can provide reference for design and analysis of HAT cycle based on multi-shaft gas turbine especially the aeroderivative gas turbine.

Study on Calculations of Humidification Tower with Humid Air Turbine Cycle at High Temperature and Pressure

Humidification is an important step in humid air turbine system. The calculation on humidification is carried out at 423.15—573.15K, 5—15MPa. The results suggest that to produce high-enthalpy moist air, high water temperature and large water flow are needed. The water temperature is the most sensitive parameter to the humidification tower. And it is better for the humidification tower to work at temperature higher than 523 K when the system pressure is higher than 5 MPa. The comparison between the model used in this paper and ideal model shows that the ideal model can be used in simulation to simply the calculation when the temperature is lower than 473 K and pressure is lower than 5 MPa.

Electro-Hydrodynamics and Kinetic Modeling of Dry and Humid Air Flows Activated by Corona Discharges

The present work is devoted to the 2D simulation of a point-to-plane Atmospheric Corona Discharge Reactor （ACDR） powered by a DC high voltage supply. The corona reactor is periodically crossed by thin mono filamentary streamers with a natural repetition frequency of some tens of kHz. The study compares the results obtained in dry air and in air mixed with a small amount of water vapour （humid air）. The simulation involves the electro-dynamics~ chemical kinetics and neutral gas hydrodynamics phenomena that influence the kinetics of the chemical species transformation. Each discharge lasts about one hundred of a nanosecond while the post- discharge occurring between two successive discharges lasts one hundred of a microsecond. The ACDR is crossed by a lateral dry or humid air flow initially polluted with 400 ppm of NO. After 5 ms, the time corresponding to the occurrence of 50 successive discharge/post-discharge phases, a higher NO removal rate and a lower ozone production rate are found in humid air. This change is due to the presence of the HO2 species formed from the H primary radical in the discharge zone.

Kinetic study of key species and reactions of atmospheric pressure pulsed corona discharge in humid air

In this study, we examined the key particles and chemical reactions that substantially influence plasma characteristics. In summarizing the chemical reaction model for the discharge process of N_(2)–O_(2)–H_(2)O(g)mixed gases, 65 particle types and 673 chemical reactions were investigated. On this basis, a global model of atmospheric pressure humid air discharge plasma was developed, with a focus on the variation of charged particles densities and chemical reaction rates with time under the excitation of a 0–200 Td pulsed electric field. Particles with a density greater than 1% of the electron density were classified as key particles. For such particles, the top ranking generation or consumption reactions(i.e. where the sum of their rates was greater than 95% of the total rate of the generation or consumption reactions) were classified as key chemical reactions. On the basis of the key particles and reactions identified, a simplified global model was derived. A comparison of the global model with the simplified global model in terms of the model parameters, particle densities, reaction rates(with time), and calculation efficiencies demonstrated that both models can adequately identify the key particles and chemical reactions reflecting the chemical process of atmospheric pressure discharge plasma in humid air. Thus, by analyzing the key particles and chemical reaction pathways, the charge and substance transfer mechanism of atmospheric pressure pulse discharge plasma in humid air was revealed, and the mechanism underlying water vapor molecules’ influence on atmospheric pressure air discharge was elucidated.

Humid Air Plasma Treatment of Birnessite Surface: Application to the Removal of Cochineal Red

The thin layers of birnessite (Mn7O13?5H2O) are exposed to reactive species gliding arc plasma in humid air, which induces the treatment of the thin layers surface. Plasma treatment thin layer of birnessite was used for the degradation of Cochineal Red. The experimental results showed that 95% of the CR solution was completely decolorized by thin layer of birnessite treated by plasma compared to 80% of the same solution after interaction of thin layer of birnessite untreated. The decay kinetics always follows a pseudo-first order reaction. The application of the humid air plasma for the surface treatment of thin layers of birnessite improves the efficiency of treatment for Cochineal Red degradation.

Design Research of a Novel Aftercool-Humidifier Concept for Humid Air Turbine Cycle

Humid air turbine cycle(HAT)has potential of electrical efficiencies comparable to combined cycle,with lower investment cost and NO_(x) emission.The typical heat exchanger network of HAT consists of intercooler(if there is),aftercooler,recuperator,economizer and humidifier,which brings higher efficiency but makes the system more complex.To simplify HAT layout,a novel humidifier concept is proposed by integrating the aftercooler into traditional counter-current humidifier.Based on this concept,a one-dimensional model including pressure drop and exergy calculation is established to distinguish the thermodynamic and hydrodynamic characteristics,and then the structural parameters,such as the number of rows and columns,tube diameter,pitch and type for a micro HAT are identified.The results show that the aftercool-humidifier plays the same role as original aftercooler and humidifier,and can match the in-tube air,out-tube air and water stream well with lower volume.In the case of micro HAT cycle,the volume of heat and mass transfer area can be reduced by 47%compared with traditional design.The major thermal resistance occurred in the convection heat transfer process inside the tube;however,using enhanced tube cannot effectively improve the compactness of device.

Effects of temperature, particle size, and air humidity on sensibility of typical high-energetic explosives

The production and utilization of high-energetic explosives often pose a range of safety hazards,with sensitivity being a key factor in evaluating these risks.To investigate how temperature,particle size,and air humidity affect the responsiveness of commonly used high-energetic explosives,a series of BAM(Bundesanstalt für Materialforschung und-prüfung)impact and friction sensitivity tests were carried out to determine the critical impact energy and critical load pressure of four representative high-energetic explosives(RDX,HMX,PETN and CL-20)under different temperatures,particle sizes,and air humidity conditions.The experimental findings facilitated an examination of temperature and particle size affecting the sensitivity of high-energetic explosives,along with an assessment of the influence of air humidity on sensitivity testing.The results clearly indicate that high-energetic explosives display a substantial decline in critical reaction energy when subjected to micrometre-sized particles and an air humidity level of 45%at a temperature of 90℃.Furthermore,it was noted that the critical reaction energy of high-energetic explosives diminishes with an increase in temperature within 25℃−90℃.In the same vein,as the particle sizes of high-energetic explosives increase,so does the critical reaction energy for micrometre-sized particles.High air humidity significantly affects the sensitivity testing of high-energetic explosives,emphasizing the importance of refraining from conducting sensitivity tests in such conditions.

基于Aqua卫星AIRS数据的南大洋大气逆温和逆湿特性研究

南大洋大气普遍存在着逆温和逆湿现象,其分布和变化对海-冰-气之间的物质和通量交换具有重要影响。利用Aqua卫星上搭载的大气红外探测器(AIRS)观测数据,提取了南大洋大气的逆温和逆湿特性,并研究了其时空分布与变化特征。此外,以全球无线电探空数据集的探测结果为参考值,分析了AIRS在进行大气逆温和逆湿探测过程中受到云量影响的特征。结果表明,AIRS估计的逆温特性受云量的影响较小,在多云条件下AIRS也可精确地估计逆温特性。利用AIRS最新的第7版(V7)数据产品对2004-2020年南大洋大气逆温和逆湿的频率(强度)进行研究,发现秋冬季比春夏季高(强),在龙尼冰架、罗斯冰架和南极半岛附近的海域的大气出现逆温和逆湿现象较其他区域更频繁,且强度更强。

Experimental Study on Turbulent Structure of Humid Air Flame in a Bluff-body Burner

The main objective of the present experimental study is to analyze the turbulent structure in humid airnon-premixed flame, and determine the effect of humidity on the flow field and the flame stability limit in turbulentnon-premixed flame. Particle Image Velocimetry (PIV) is used to capture the instantaneous appearance ofvortex structures and obtain the quantitative velocity field. The distributions of Reynolds shear stress, mean androot-mean squared fluctuating (rms) velocities are examined to get insight into the effect of fuel-to-air velocity ratioon velocity flow field. The results show that with steam addition, the air-driven vortex in the bluff-body wakeis thinner; the biggest peaks of rms velocity and Reynolds shear stress are lower; the distance between the peaksof rms velocity on the sides of centerline reduces. Besides these, the flame stability is affected. Both central fuelpenetration limit and partially quenching limit reduce with steam addition.

＂Partial pressures＂ of humid air in wide pressure and temperature ranges

＂Partial pressure＂ in humid air is a question very much concerned by scientists and no satisfactory answer has been found to date. This paper proposes a novel method to obtain the ＂partial pressures＂ of the water vapor and dry air in humid air. The results obtained by the proposed method are quite different from that obtained by Dalton＇s partial pressure law. The fundamental behaviors of water vapor and dry air are studied in depth in wide pressure and temperature ranges. Semi-permeable membrane models are proposed and applied for both saturated and unsaturated humid air. ＂Improvement factors＂ are developed to quantitatively describe the magnitude of the interaction between dissimilar molecules. One discovery is that the ＂partial pressure＂ of the water vapor in saturated humid air equals Ps, rather than （f.Ps） which was formerly believed. The other is that the interaction between dissimilar molecules may be omitted when temperature is above ＂cutting-off temperature＂ for unsaturated humid air. This paper satisfactorily answers the quest of ＂partial pressures＂ in humid air from a new perspective.

Hyperbranched phthalocyanine enabling black-phase formamidinium perovskite solar cells processing and operating in humidity open air

The extreme instability of pureα-phase FAPbI_(3) under high humidity conditions restricts the highthroughput fabrication in unmodified air environments,resulting in poor performance ofα-phase FAPbI_(3) perovskite devices obtained by scalable fabrication methods.Here we synthesized hyperbranched copper phthalocyanine(HCuPc)as a supramolecular additive with twisted phthalocyanine units to realize the molecular-level encapsulation at the grain boundaries through supramolecular interaction,which greatly broadened the processing window of FAPbI_(3) under high humidity.At the same time,unlike traditional encapsulation layer that carrier can only be collected by tunneling effect,the twisted phthalocyanine ring of HCu Pc in perovskite films is more conducive to hole extraction.Finally,a record efficiency was achieved in pure FAPbI_(3) based inverted structured solar cell by blade-coating to the best of our knowledge,even under unmodified humid air conditions(relative humidity of 65%–85%).The best operational stability of 3D pure FAPbI_(3) devices can also be achieved at the same time and unencapsulated HCuPc-FAPbI_(3) device can even operate with negligible degradation for 100 h in the open air(RH 30%–40%).

Development and experimental validation of a one-dimensional dynamic hygrothermal modeling based on air humidity ratio

A modified one-dimensional transient hygrothermal model for multilayer wall was proposed using air humidity ratio and temperature as the driving potentials.The solution for the governing equations was obtained numerically by implementing the finite-difference scheme.To evaluate the accuracy of the model,a test system was built up to measure relative humidity and temperature within a porous wall and compare with the prediction of the model.The prediction results have good agreement with the experimental results.For the interface close to indoor side,the maximum deviation of temperature between calculated and test data is 1.87 K,and the average deviation is 0.95 K;the maximum deviation of relative humidity is 11.4%,and the average deviation is 5.7%.For the interface close to outdoor side,the maximum deviation of temperature between prediction and measurement is 1.78 K,and the average deviation is 1.1 K;the maximum deviation of relative humidity is 9.9%,and the average deviation is 4.2%.

Seasonal Variation in Air Temperature and Relative Humidity on Building Areas and in Green Spaces in Beijing, China

The cooling and humidifying effects of urban parks are an essential component of city ecosystems in terms of regulating microclimates or mitigating urban heat islands(UHIs).Air temperature and relative humidity are two main factors of thermal environmental comfort and have a critical impact on the urban environmental quality of human settlements.We measured the 2-m height air temperature and relative humidity at the Beijing Olympic Park and a nearby building roof for more than 1 year to elucidate seasonal variations in air temperature and relative humidity,as well as to investigate the outdoor thermal comfort.The results showed that the lawn of the park could,on average,reduce the air temperature by(0.80±0.19)℃,and increase the relative humidity by(5.24±2.91)% relative to the values measured at the building roof during daytime.During the nighttime,the lawn of the park reduced the air temperature by(2.64±0.64)℃ and increased the relative humidity by(10.77±5.20)%.The park was cooler and more humid than surrounding building area,especially in night period(more pronounced cooling with 1.84℃).Additionally,the lawn of the park could improve outdoor thermal comfort through its cooling and humidifying effects.The level of thermal comfort in the park was higher than that around the building roof for a total of 11 days annually in which it was above one or more thermal comfort levels(average reduced human comfort index of 0.92)except during the winter.

CORRELATION BETWEEN PEAK INTENSITY OF EXTREME AFTERNOON SHORT-DURATION RAINFALL AND HUMIDITY AND SURFACE AIR TEMPERATURE IN SOUTHEAST COAST OF CHINA

Using hourly rainfall intensity, daily surface air temperature, humidity and low-level dew point depressions at55 stations in the southeast coast of China, and sea surface temperature from reanalysis in the coastal region, this paper analyzes the connection between peak intensity of extreme afternoon short-duration rainfall(EASR) and humidity as well as surface air temperature. The dependency of extreme peak intensity of EASR on temperature has a significant transition. When daily highest surface temperature is below(above) 29°C, the peak rainfall intensity shows an ascending(descending) tendency with rising temperature. Having investigated the role of moisture condition in the variation of EASR and temperature, this paper discovered that the decrease of peak rainfall intensity with temperature rising is connected with the variation of relative humidity. At higher temperatures, the land surface relative humidity decreases dramatically as temperature further increases. During this process, the sea surface temperature maintains basically unchanged, resulting in indistinct variations of water vapor content at seas. As water vapor over land is mainly contributed by the quantitative moisture transport from adjacent seas, the decline of relative humidity over land will be consequently caused by the further rise of surface air temperature.

The Experiment and Simulation of Solid Desiccant Dehumidification for Air-Conditioning System in a Tropical Humid Climate

The aim of this research was to study and design a solid desiccant dehumidification system suitable for tropical climate to reduce the latent load of air-conditioning system and improve the thermal comfort. Different dehumidifiers such as desiccant column and desiccant wheel were investigated. The ANSYS and TRASYS software were used to predict the results of dehumidifiers and the desiccant cooling systems, respectively. The desiccant bed contained approximately 15 kg of silica-gel, with 3 mm average diameter. Results indicated that the pressure drop and the adsorption rate of desiccant column are usually higher than those of the desiccant wheel. The feasible and practical adsorption rate of desiccant wheel was 0.102 kgw/h at air flow rate 1.0 kg/min, regenerated air temperature of 55?C and at a wheel speed of 2.5 rpm. The humidity ratio of conditioning space and cooling load of split-type air conditioner was decreased to 0.002 kgw/kgda (14%) and 0.71 kWth (19.26%), respectively. Consequently, the thermal comfort was improved from 0.5 PMV (10.12% PPD) to 0.3 PMV (7.04% PPD).

STUDY OF THE HEAT AND HUMIDITY TRANSFER PROCESSES BETWEEN AIR AND WATER IN THE AIR WASHER

The processes of heat and humidity transfer between air and water are what to be studied mainly in the paper, we put forward some main factors which influence the processes of heat and humidity transfer in the air washer. We come to the conclusion that we can change these main factors to achieve different heat and humidity transfer processes and decide processes of heat and humidity transfer of air and water with the initial temperature of spraying water in the air washer. All these results can make things convenient for the air conditioning management.

COMPUTER DECOUPLE CONTROL OF TEMPERATURE AND HUMIDITY IN PREPROCESSING CHAMBER OF AIR-CONDITIONING TEST EQUIPMENT

This paper deals with the application of decouple Control theory to temperature and humidi-ty control in air-conditioning system. The decouple control algorithm for bivariable systems isderived applicablly for air-conditioning system. The algorithm is used to design a temperatureand humidity computer control system for the preprocessing chamber of air-conditioning testequipment. The results of the real-time control experiments indicate that the decouple controlalgorithm is feasible, the control quality is improved and high control precision is achieved.

造纸机干燥部排风系统节能优化设计研究

为实现针对造纸机干燥部排风系统的节能优化,降低造纸企业的生产经营成本,收集了某造纸企业提供的干燥部信息管理系统数据并建立了服务于排风系统节能优化的弹性网络模型。通过该模型对干燥部排风系统内各个排风机的排风温湿度进行预测,发现弹性网络模型对排风机排风温湿度的预测效果显著优于支持向量回归模型。因此,基于弹性网络的节能优化模型应用于110 g/m^(2)红杉纸、90 g/m^(2)挂面箱板纸、120 g/m^(2)挂面箱板纸等3条产品线的排风系统参数调节工作中。根据生产应用结果发现,3条纸张产品生产线经过参数调节后的吨绝干纸干燥成本依次下降了0.72%、0.68%、1.07%,体现出了较为理想的节能优化效果。

严寒地区混合垂直通风猪舍环境质量评价

为探究垂直通风系统(屋顶与粪坑混合排风)在寒区猪舍中的适应性,该研究在秋冬季节对内蒙古某规模化猪舍的热湿与空气质量环境进行了实时连续监测,并根据测试结果对猪舍环境质量进行评价。结果表明:1)测试期间,舍内平均温度、相对湿度以及氨气(NH_(3))、二氧化碳(CO_(2))、总悬浮颗粒物(total suspended particulate, TSP)浓度分别为22.7℃、59.6%、6.5 mg/m^(3)、2 200 mg/m^(3)、2 915μg/m^(3),舍内通风量为0.34~0.39 m^(3)/(h·kg),各环境指标基本满足生产环境阈值要求;保育期间舍内有效环境温度范围为27.1~30.7℃,存在轻度热应激情况,占总监测时间的12.9%;2)舍内温度、相对湿度与NH_(3)、CO_(2)、TSP浓度空间分布不均匀系数分别为0.01、0.15、0.45、0.03、0.15,各环境参数空间分布均较为均匀;3)试验单元(U1、U3)猪的平均日增质量、料重比与死淘率分别842和818 g/d、2.68和2.79、1.68%和1.31%,生产性能良好。综上,不设吊顶的侧墙进风,屋顶与粪坑混合排风的垂直通风系统,总体上能够满足严寒地区猪舍秋冬季热湿环境与空气质量调节需求,保证良好的生产性能。

风道结构改善货架式冷库热环境的数值模拟研究

本文采用数值模拟的方法探索风道结构对货架式冷库热环境的影响,分析风道结构各因素对热环境评价指标的影响程度。研究结果显示,在本文所设计的12种工况中,风道结构直接影响冷库温湿度分布均匀性和能量利用率,温度不均匀系数、相对湿度不均匀系数随着无因次风道宽度增加而下降,随着开口率的增加而减小。采用极差分析法和方差分析法判断多种因素对评价指标的影响显著程度,并根据综合平衡法得到最优工况,即第13种工况:无因次风道宽度为0.5,开口率为11.8%,该工况下温度及相对湿度不均匀系数分别下降为0.09及0.016、能量利用系数提高至1.68,可显著改善货架式冷库热环境。