Scavenging Microwave Wireless Power:A Unified Model,Rectenna Design Automation,and Cutting-Edge Techniques

While sufficient review articles exist on inductive short-range wireless power transfer(WPT),long-haul microwave WPT(MWPT)for solar power satellites,and ambient microwave wireless energy harvesting(MWEH)in urban areas,few studies focus on the fundamental modeling and related design automation of receiver systems.This article reviews the development of MWPT and MWEH receivers,with a focus on rectenna design automation.A novel rectifier model capable of accurately modeling the rectification process under both high and low input power is presented.The model reveals the theoretical boundary of radio frequency-to-direct current(dc)power conversion efficiency and,most importantly,enables an automated system design.The automated rectenna design flow is sequential,with the minimal engagement of iterative optimization.It covers the design automation of every module(i.e.,rectifiers,matching circuits,antennae,and dc–dc converters).Scaling-up of the technique to large rectenna arrays is also possible,where the challenges in array partitioning and power combining are briefly discussed.In addition,several cutting-edge rectenna techniques for MWPT and MWEH are reviewed,including the dynamic range extension technique,the harmonics-based retro-directive technique,and the simultaneous wireless information and power transfer technique,which can be good complements to the presented automated design methodology.

Design of Traditional Chinese Medicine Extraction Workshop Process and Automation System

Objective: This paper takes the example of a Panax notoginseng extraction workshop and designs an automated production workshop with advanced domestic capabilities. Methods: 1) Based on the small-scale Panax notoginseng extraction process, the feasibility of the workshop production process is demonstrated. 2) The workshop process design for Panax Notoginseng saponin extraction is completed, including production organization plans and the selection of key equipment. 3) For the Panax notoginseng extraction workshop process, an automated production control system is designed. Conclusion: Through optimized design of the production process and automation system, continuous and automated production of traditional Chinese medicine extraction is achieved, leading to improvements in drug quality and production efficiency.

Integrating Universal Design Standards and Building Information Modeling at the Conceptual Design Stage of Buildings

A projection of the Canadian population shows that in 2024 one in five Canadians will be over 65 years old. This shift forces designers to consider the entire lifetime of occupants during the design of new buildings. Universal Design (UD), which is a design that accommodates all people to the greatest extent possible and aging in place design that is deeply rooted in the principles of UD, aim to house people irrespective of their age, ability, and chronic health conditions. Building Information Modeling (BIM) significantly helps advance the development of the Architecture, Engineering, and Construction (AEC) industry in a more collaborative and automated way. Integrating BIM and UD allows designers to incorporate UD standards easily and efficiently at the conceptual design stage of buildings by using the functionalities and capabilities of BIM tools. Therefore, this study presents the development of an automated computer model to facilitate the adoption of UD standards and processes. The novelty highlighted in this model resides in the creation of an automated method that employs a newly created plug-in and databases to assist designers to incorporate UD standards at the conceptual stage in a timely and cost-effective manner. Furthermore, the study introduces the methodology consisting of collecting, categorizing, and storing data from various universal design and accessible design guidelines in the developed databases and developing new plug-ins in BIM tool to link the developed databases in order to automate the process of retrieving necessary information and components to help designers and owners select optimal design alternatives based on their predefined criteria.

Development of Parametric Design System Based on AutoCAD Automation

This paper discusses the method of how to develop the parametric design system. It presents an idea and a method of developing AutoCAD R14 with the help of VB, AutoLISP and DantaBase system on the base of AntoCAD Automation technology. Therefore, the question of how to integrate the user's interface, data (DataBase) management and parameter transformation can be solved properly.

Research on Electrical Automation Control Design Based on PLC Technology

As science and technology continue to progress forward,electrical automation engineering is also developing,of which programmable logic controller(PLC)technology is widely being used.Through the integration of PLC technology and traditional electrical automation technology,good development of modern science and technology is promoted while traditional automation is preserved.The development of electrical engineering can greatly improve the strength of science,technology,and economy in our country.Based on PLC technology,this paper analyzes the design of electrical automation control.

Practice Teaching Reform of Mechanical Design and Manufacture and Its Automation Specialty under Transformation and Development

With the development of the times, undergraduate colleges and universities begin to transform and develop to adapt to the changing society, and put forward new requirements for practical teaching strategies, especially for applied undergraduate colleges. The reform of practical teaching is particularly important. Under the development of education transformation, the reform of mechanical design and manufacture and the practice teaching of automation specialty also occupy a very important position. Through the understanding of the reform of the practical teaching of this specialty, the effect of the reform is observed, and a reasonable teaching scheme is put forward to promote the steps of the transformation of the practical teaching.

Electromagnetic Simulation with 3D FEM for Design Automation in 5G Era

Electromagnetic simulation and electronic design automation(EDA)play an important role in the design of 5G antennas and radio chips.The simulation challenges include electromagnetic effects and long simulation time and this paper focuses on simulation software based on finite-element method(FEM).The state-of-the-art EDA software using novel computational techniques based on FEM can not only accelerate numerical analysis,but also enable optimization,sensitivity analysis and interactive design tuning based on rigorous electromagnetic model of a device.Several new techniques that help to mitigate the most challenging issues related to FEM based simulation are highlighted.In particular,methods for fast frequency sweep,mesh morphing and surrogate models for efficient optimization and manual design tuning are briefly described,and their efficiency is illustrated on examples involving a 5G multiple-input multiple-output(MIMO)antenna and filter.It is demonstrated that these new computational techniques enable significant reduction of time needed for design closure with the acceleration rates as large as tens or even over one hundred.

Applying the disciplinary relation matrix to multidisciplinary design optimization modeling and solving

A new efficient coupling relationship description method has been developed to provide an automated and visualized way to multidisciplinary design optimization (MDO) modeling and solving. The disciplinary relation matrix (DRM) is proposed to describe the coupling relationship according to disciplinary input/output variables, and the MDO definition has been reformulated to adopt the new interfaces. Based on these, a universal MDO solving procedure is proposed to establish an automated and efficient way for MDO modeling and solving. Through a simple and convenient initial configuration, MDO problems can be solved using any of available MDO architectures with no further effort. Several examples are used to verify the proposed MDO modeling and solving process. Result shows that the DRM method has the ability to simplify and automate the MDO procedure, and the related MDO framework can evaluate the MDO problem automatically and efficiently.

Automatic Virtual Entity Simulation of Conceptual Design Results—Part Ⅰ:Symbolic Scheme Generation and Identification

The development of new products of high quality, low unit cost, and short lead time to market are the key elements required for any enterprise to obtain a competitive advantage. For shorting the lead time to market and improving the creativity and performances of the product, a rule-based conceptual design approach and a methodology to simulate the conceptual design results generated in conceptual design process in automatical virtual entity form are presented in this paper. This part of paper presents a rule-based conceptual design method for generating creative conceptual design schemes of mechanisms based on Yan＇s kinematic chain regeneration creative design method. The design rules are adopted to describe the design requirements of the functional characteristics, the connection relationships and topological characteristics among mechanisms. Through the graphs-based reasoning process, the conceptual design space is expanded extremely, and the potential creative conceptual design results are then dug out. By refining the design rules, the solution exploration problem is avioded, and the tendentious conceptual design schemes are generated. Since mechanical, electrical and hydraulic subsystems can be transformed into general mechansims, the conceptual design method presented in this paper can also be applied in the conceptual design problem of complex mechatronic systems. And then the method to identify conceptual design schemes is given.

Rationale and Design of the Randomized Controlled Trial of Intensive Versus Usual ECG Screening for Atrial Fibrillation in Elderly Chinese by an Automated ECG System in Community Health Centers in Shanghai(AF-CATCH)

Objective:The randomized controlled trial(ClinicalTrials.gov identifier NCT02990741)will investigate whether more frequent electrocardiographic(ECG)recordings and analyses with an automated ECG system would improve detection of atrial fibrillation compared with a single annual ECG screen in elderly Chinese in community health centers.Design:Men and women(≥65 years)will be randomized into intensive(n=3500)and usual(n=3500)screening groups,and within the intensive screening group into intensive screening(n=2625)and more intensive screening(n=875)subgroups.ECG recordings will be performed with an automated ECG analysis system(AliveCor heart monitor)at 1 year in the usual screening group,at 3,6,9,and 12 months in the intensive screening subgroup,and at 1,2,3,and 4 weeks and 3,6,9,and 12 months in the more intensive screening subgroup.The primary outcome is the detection rate of atrial fibrillation between the usual screening group and the intensive screening group.Sample size estimation was based on a projected detection rate of atrial fibrillation of 2.0% by a single ECG recording at 12 months,an improvement of 50% with more frequent ECG recordings,α=0.05,power of 80%,and a one-sided test.Conclusions:The trial will provide evidence on the clinical effectiveness of more frequent ECG recordings by a handheld automated analysis system in the detection of atrial fibrillation.

Research on Theory of Green Product DesignAutomation

Facing with the design activihes of low efficacy and low standard on design automationdue to the probabilishc, non-rational and non-standard product design. This Paper puts forward thetheory of generalized mapping, which is proved to be effective in the enhancemed of the creativity ofproduct design automation. It further explores the applicahon and progress in the creative greenproduct conceptual and detail design.

Synopsys收购ANALOG DESIGN AUTOMATION公司

Synopsys公司日前正式宣布．全面收购ANALOG DESIGN AUTOMATION(ADA)公司韵所有资产。ADA是为模拟信号、混合信号及定制集成电路提供自动化电路优化解决方案的领先供应商．这将扩展Synopsys在模拟和混合信号方面的实力。通过这一收购．

AUTOMATIC APPROACH TO PRODUCT CONCEPTUAL DESIGN BASED ON CONSTRAINT NETWORK

Product design is considered as the constraint satisfaction problem (CSP),and a new design approach basedon constraint network is proposed and applied to make designautomatic partially. By means of constraint extraction, constraint network construction andoperation, constraint chains are acquired, and then the conceptual design scheme can be got bydecoding the information stored in the design constraint chains, which provides a novelty method formechanical product design automation. Shearing mechanism of shearing machine has been designed bythis way.

Automatic Virtual Entity Simulation of Conceptual Design Results—Part Ⅱ:Symbolic Scheme Simulation

The development of new products of high quality, low unit cost, and short lead time to market are the key elements required for any enterprise to obtain a competitive advantage. This part of the paper presents a methodology to automatically simulate the conceptual design results in the virtual entity form. To the identified basic mechanisms, their kinematic analysis is carried out by matching basic Barranov trusses, and their virtual entities are modeled based on feature-based technique and encapsulated as one design object. Based on the structures of the basic mechanisms and their connections, a space layout to the mechanical system corresponding to the symbolic scheme is then fulfilled. With the preset-assembly approach, all parts in the mechanical system are put onto proper positions where the constraint equations are met according to the space layout results. In this way, the virtual entity assembly model of the mechanical system relative to the symbolic scheme is set up. The approach presented in this paper can not only obtain innovative conceptual conceptual design results, but also can evaluate their performances under 3-D enviroment efficently.

Improvement of the Life Cycle Costing Method in DesignStage Using KBIMS Library

With the advent of the fourth industrial revolution,the construction industry has undergone a paradigm shift.The smart construction technology market is expected to grow 12%annually in developed countries due to advanced technology investments.It is expected that businesses requiring highly sophisticated technology,for instance companies that need their old facilities upgraded,will become the main focus of the market.As building information modeling(BIM)design is becoming mandatory,such as in the Korea Public Procurement Service,researches regarding building automation,construction,and operation integration management systems based on BIM are conducted.In addition,for construction projects of over 10 billion won,design value engineering(Design VE)implementation,including life cycle cost(LCC)analysis,is mandatory at the design stage to improve quality and reduce the lifetime costs of buildings.In this study,we propose an improvement plan for LCC analysis at the design stage using the KBIMS library,which is an open BIM library developed by the Korean government and research groups.We analyze the existing LCC method,KBIMS library,and attribute information,and model the process that is applied in the LCC analysis system.This is expected to complement the LCC analysis system and improve work productivity.

Evaluation of a Novel Approach for Automated Inventive Conceptual Design of Building Structures

This research is dedicated to assessment of a method that was earlier proposed and developed in order to increase the degree of automation and software involvement into conceptual decision making during design of structural elements of buildings. Such instruments of the theory of inventive problem solving as contradiction and function analysis and trimming formed the basis of the proposed approach that was realized in a modern building information modeling software. The common logic of the approach is also provided in the article. Qualitative research methods and particularly collecting, analyzing and interpreting data were applied in this research. Firstly, a literature review of indexed journal articles in the field of the study was performed and some trends for possible development of the topic were identified. Secondly, a survey of potential users of the methodology was conducted and analyzed. The questionnaire results showed that the suggested method and its technical realization gained attraction among respondents, however, some of them are rather cautious regarding application of the approach potentials in their practice. The paper ends with evaluation results discussion, conclusion and proposals for further research.

Immune Genetic Algorithm for Optimal Design

A computing model employing the immune and genetic algorithm (IGA) for the optimization of part design is presented. This model operates on a population of points in search space simultaneously, not on just one point. It uses the objective function itself, not derivative or any other additional information and guarantees the fast convergence toward the global optimum. This method avoids some weak points in genetic algorithm, such as inefficient to some local searching problems and its convergence is too early. Based on this model, an optimal design support system (IGBODS) is developed.IGBODS has been used in practice and the result shows that this model has great advantage than traditional one and promises good application in optimal design.

基于Altium Designer的电子电路仿真设计

电子电路仿真设计,是现代电子工程领域进行电路系统设计的EDA新技术,设计方案介绍了EDA软件-Altium Designer的特点及主要仿真功能,并以Altium公司推出和应用较广的Protel 99SE为例,介绍了静态工作点分析、傅立叶瞬态分析、频率特性分析、参数扫描分析、温度扫描分析和噪声分析等电路仿真设计的方法,可以优化电路性能、缩短设计周期和提高设计效率。