Recursive Asymptotic Hybrid Matrix Method for Acoustic Waves in Multilayered Piezoelectric Media

This paper presents the recursive asymptotic hybrid matrix method for acoustic waves in multilayered piezoelectric media. The hybrid matrix method preserves the numerical stability and accuracy across large and small thicknesses. For discussion and comparison, the scattering matrix method is also presented in physics-based form and coherent form. The latter form resembles closely that of hybrid matrix method and helps to highlight their relationship and distinction. For both scattering and hybrid matrix methods, their formulations in terms of eigenwaves solution are provided concisely. Making use of the hybrid matrix, the recursive asymptotic method without eigenwaves solution is described and discussed. The method bypasses the intricacies of eigenvalue-eigenvector approach and requires only elementary matrix operations along with thin- layer asymptotic approximation. It can be used to determine Green’s function matrix readily and facilitates the trade-off between computation efficiency and accuracy.

Influence of Machining Parameter on Tool Life While Machining Hybrid Metal Matrix Composites

A metal matrix composite constitutes a continuous metallic matrix and a discontinuous phase known as reinforcement. The hybrid metal matrix composites (Hmmcs) have been used to manufacture drive shafts, disc brake rotors, brake drums, connecting rods pistons, engine block cylinder liners for automotive and rail vehicle applications. The Hmmcs castings of diameter 120 mm and length 300 mm were prepared through sand mould technique following stir casting methodology. The cast components further subjected to evaluation of physical properties and machining tests using two grades of coated inserts and PCD inserts. The experiments were carried out following ISO 3685 standards. The coating thickness of the TiN coated and TiAlN coated inserts were measured using Kalo testing method; the results of the test show that the interface of the substrate and coating was free from the porosity, and the coating thickness of TiN coating was 4.84 microns and TiAlN coating was measured 4.6 microns. The results of the experiments show that performance of the PCD insert was better than coated inserts at 0.1 mm/rev feed; however at 0.2 mm/revolution feed PCD insert failed by micro chipping of cutting edge while machining Hmmcs. When TiAlN coated inserts were used to machine Hmmcs the coated inserts failed by gradual wear and BUE formation.

Optimization of Friction and Wear Behaviour in Hybrid Metal Matrix Composites Using Taguchi Technique

Al-7075 alloy-base matrix, reinforced with mixtures of silicon carbide (SiC) and boron carbide (B4C) particles, know as hybrid composites have been fabricated by stir casting technique (liquid metallurgy route) and optimized at different parameters like sliding speed, applied load, sliding time, and percentage of reinforcement by Taguchi method. The specimens were examined by Rockwell hardness test machine, Pin on Disc, Scanning Electron Microscope (SEM) and Optical Microscope. A plan of experiment generated through Taguchi’s technique is used to conduct experiments based on L27 orthogonal array. The developed ANOVA and the regression equations were used to find the optimum wear as well as co-efficient of friction under the influence of sliding speed, applied load, sliding time and percentage of reinforcement. The dry sliding wear resistance was analyzed on the basis of “smaller the best”. Finally, confirmation tests were carried out to verify the experimental results.

Research on consistency measurement and weight estimation approach of hybrid uncertain comparison matrix

The consistency measurement and weight estimation approach of the hybrid uncertain comparison matrix in the analytic hierarchy process （AHP） are studied. First, the decision-making satisfaction membership function is defined based on the decision making＇s allowable error. Then, the weight model based on the maximal satisfactory consistency idea is suggested, and the consistency index is put forward. Moreover, the weight distributing value model is developed to solve the decision making misleading problem since the multioptimization solutions in the former model. Finally, the weights are ranked based on the possibility degree approach to obtain the ultimate order.

Optimization of Wear Factors of Aluminium Hybrid Metal Matrix Composites Using Taguchi Method

Hybrid metal matrix composites (Hmmc) are found to be more superior than the conventional composite materials because of their improved mechanical properties, which can be suited for an extensive range of engineering applications. Automobile and aerospace industries widely make use of hybrid composites as they possess excellent corrosion, wear resistance, low density, and high strength. This paper displays the strategy to build the hybrid composite utilizing Stir casting Method. Present investigation includes the creation of composites utilizing boron carbide (2%, 4%, 6% volume) and Red mud (2% volume) as the reinforcements and Structural aluminium as the matrix. Experimental investigation of wear analysis of the composites was carried out according to the L9 Taguchi method. The designated number of experiments was accomplished to probe the impact of control factors on the specific wear rate (SWR) of the developed composites. ANOVA was carried out and Wt%. Reinforcement was found to be the decisive factor on the SWR of the developed hybrid composite. The Confirmatory test was successfully carried out and the computed error was found to be varying from 0.878% to 2.58%.

Observation on In Situ Hybridization and Immunocytochemistry of Matrix Metalloproteinases in Rat Pancreas

In situ hybridization and immunocytochemical techniques were employed to examine the expression of matrix metalloproteinases 1 (MMP 1) and to identify the pattern of its distribution in rat pancreas. The results indicated that the signal of MMP 1 mRNA and MMP 1 positive immunoreaction were detected in some fiberoblasts around interlobular ducts and exocrine cell in margin acinus of some lobules, but the signal of MMP 1 mRNA and MMP 1 positive immunoreaction could not be detected in most of other acinus and islets of pancreas. It is concluded that the expression of MMP 1 in above cells of rat might play an important role in acinar proliferation and differentiation of rat pancreatic tissues.

Analysis of the Machining Characteristics on Surface Roughness of a Hybrid Aluminium Metal Matrix Composite (Al6061-SiC-Al₂O₃)

Aluminium metal matrix composites are finding increased applications in many areas. Adding of the third element to the metal matrix make the composite hybrid. This paper presents the study on the surface roughness characteristics of a hybrid aluminium metal matrix (Al6061-SiC-Al2O3) composites. The experimental studies were carried out on a lathe. The composites were prepared using the liquid metallurgy technique, in which 3, 6 and 9 wt % of particulates SiC and Al2O3 were dispersed in the base matrix. The obtained cast composites were carefully machined. The characteristics that influence the surface roughness such as feed rate, depth of cut and cutting speed were studied, which made the analysis come to a conclusion that the surface roughness is increases with the increase of feed rate and it reduces the surface roughness with the increase of cutting speed.

Morphology and Electronic Properties of Hybrid Organic-Inorganic System: Ag Nanoparticles Embedded into CuPc Matrix

Materials with a high on-off resistance ratio could become the basis for resistive random-access memory (RRAM). It is assumed that one of RRAM types can be based on hybrid organic-inorganic systems, while particular attention is focused on hybrid systems consisting of metal nanoparticles (NP) embedded in organic matrix (OM). In this investigation we created and studied the hybrid organic-inorganic systems made of metal (Ag) nanoparticles embedded in organic semiconductor material CuPc. The LEED patterns and NEXAFS data demonstrate that the CuPc films deposited on Au(001) substrate are highly ordered and molecular planes lie parallel to the gold surface. The metal atoms were deposited on the outer surface of the organic molecular film and self-assembled into nanoparticles due to surface and bulk diffusion. The properties of nano-composite materials seem to be significantly dependent on the microstructure, i.e. the size, concentration, bulk- and size-distribution of nanoparticles;therefore we have studied by high resolution transmission electron microscopy the evolution of morphology of nano-composite films as a function of nominal metal deposition. The filled and empty electronic states of the hybrid organic-inorganic systems, energy level alignment at interfaces formed between metal nanoparticles and the organic semiconductor CuPc as well as the chemical interaction at the NP/OM interface were studied by UPS, XPS and NEXAFS methods.

THE STRESS SUBSPACE OF HYBRID STRESS ELEMENT AND THE DIAGONALIZATION METHOD FOR FLEXIBILITY MATRIX H

The following is proved: 1) The linear independence of assumed stress modes is the necessary and sufficient condition for the nonsingular flexibility matrix; 2) The equivalent assumed stress modes lead to the identical hybrid element. The Hilbert stress subspace of the assumed stress modes is established. So, it is easy to derive the equivalent orthogonal normal stress modes by Schmidt's method. Because of the resulting diagonal flexibility matrix, the identical hybrid element is free from the complex matrix inversion so that the hybrid efficiency, is improved greatly. The numerical examples show that the method is effective.

混杂颗粒增强Ni基复合材料的冲蚀磨损性能研究

煤炭开采、石油化工等极端工况条件下的机械装备对部分关键零部件材料的磨损性能提出了更高要求。本研究设计制备了大尺寸氧化锆颗粒(ZTAp)承载与小尺寸碳化钨颗粒(WCp)强化基体相结合的混杂颗粒增强金属基复合材料,研究了介质、冲蚀角度、ZTAp尺寸、WCp含量对复合材料冲蚀磨损性能的影响及其机理。结果表明,适量ZTAp、WCp的添加能够显著提高复合材料的抗冲蚀磨损性能。固定体积分数的ZTA颗粒,尺寸越大,复合材料冲蚀磨损性能越好,其主要失效形式为脆性剥落和疲劳断裂。WC颗粒通过第二相增强、固溶强化以及析出强化的方式,提高了基体的硬度和耐磨性,抑制了酸性介质中腐蚀与磨损的交互作用,冲蚀过程中主要失效形式为脆性断裂剥落。

基于混合正则化方法的结构载荷识别与响应重构

针对结构载荷识别与响应重构问题中存在的不适定性,提出一种最小平方残差(least square minimal residual,LSMR)算法与Tikhonov正则化方法相结合的混合正则化方法,实现利用结构有限测点的加速度响应识别载荷并重构未知的各类型响应。首先,基于时域状态空间模型构建结构的传递矩阵,并建立载荷识别与响应重构方程;其次,采用混合正则化方法改善载荷识别问题的不适定性,得到载荷的正则化解,并结合响应重构方程的传递矩阵对结构的位移、速度和加速度响应进行重构;最后,通过简支梁数值仿真和试验分析验证所提方法的可行性。结果表明,所提方法能改善重构方程的不适定性,从而对结构未知载荷和各类型响应进行有效重构。

序列二次规划方法在斜拉桥索力调整中的应用研究

斜拉桥施工至成桥阶段时,由于各种因素影响,结构实际线形和内力与理论成桥状态相比,存在一定的误差,通常需要进行索力调整。该文针对斜拉桥在调索阶段的索力调整量计算问题,提出采用一种基于影响矩阵和序列二次规划求解索力调整量的方法。以某大跨度混合梁斜拉桥为背景,首先计算各索力单位变化下结构的线形和内力响应值,得到索力影响矩阵,然后选取合适的目标函数及约束条件,构建索力调整量计算模型,最后引入序列二次规划法求解索力调整量,得到索力调整后的结构内力与线形状态。计算结果表明:该方法计算简便,索力调整后的结构线形与内力均能满足施工控制要求。

尿液基细胞荧光原位杂交检测对膀胱尿路上皮癌的诊断价值

目的探讨尿液基细胞学(LBC)靶向的荧光原位杂交(FISH)对膀胱尿路上皮癌(BUC)的诊断价值。方法回顾性收集2020年10月—2022年10月于首都医科大学附属北京天坛医院泌尿外科行膀胱镜检查的128例患者的临床资料。所有患者在行膀胱镜检查前进行尿核基质蛋白22(NMP22)检测、尿LBC检测与尿LBC靶向的FISH检测,以术后病理结果为标准,分析3种检查方法的灵敏度和特异度。结果NMP22、尿LBC与LBC靶向的FISH的灵敏度分别为61.11%、79.17%、82.46%,特异度分别为57.14%、73.21%、86.67%;NMP22、尿LBC的灵敏度在检测高级别BUC时优于低级别,差异有统计学意义(P=0.01,P=0.03);3种方法对肌层浸润性膀胱癌与非肌层浸润性膀胱癌检测的灵敏度比较,差异无统计学意义(P≥0.05)。结论尿LBC靶向的FISH对BUC诊断的灵敏度和特异度较高,尤其是对于低级别BUC,可以作为BUC早期筛查、诊断的重要方法。

Hybrid Control Strategy for Matrix Converter Fed Wind Energy Conversion System

In this paper, a hybrid control strategy for a matrix converter fed wind energy conversion system is presented. Since the wind speed may vary, output parameters like power, frequency and voltage may fluctuate. Hence it is necessary to design a system that regulates output parameters, such as voltage and frequency, and thereby provides a constant voltage and frequency output from the wind energy conversion system. Matrix converter is used in the proposed solution as the main power conditioner as a more efficient alternative when compared to traditional back-back converter structure. To control the output voltage, a vector modulation based refined control structure is used. A power tracker is included to maximize the mechanical output power of the turbine. Over current protection and clamp circuit input protection have been introduced to protect the system from over current. It reduces the spikes generated at the output of the converter. The designed system is capable of supplying an output voltage of constant frequency and amplitude within the expected ranges of input during the operation. The matrix converter control using direct modulation method, modified Venturini modulation method and vector modulation method was simulated, the results were compared and it was inferred that vector modulation method was superior to the other two methods. With the proposed technique, voltage transfer ratio and harmonic profile have been improved compared to the other two modulation techniques. The behaviour of the system is corroborated by MATLAB Simulink, and hardware is realized using an FPGA controller. Experimental results are found to be matching with the simulation results.

脱合金工艺对混杂增强非晶复合材料组织与性能的影响

基于金属熔体脱合金法制备了具有核壳混杂增强结构(核相为高熔点富Ta相,壳为B2-CuZr相)的[(Zr_(0.5)Cu_(0.5))_(92.5)Al_(7)Sn_(0.5)]_(0.95)Ta_(5)非晶复合材料,系统研究了不同脱合金工艺参数下非晶复合材料的显微组织及力学性能的演变规律。结果表明:脱合金温度和时间是控制富Ta相尺寸的关键参数。当反应温度过低或反应时间过短时,会造成富Ta相聚集、增强相分布不均匀;当反应温度过高或反应时间过长时,会导致富Ta相粗化。当脱合金反应时间为2 min、脱合金反应温度为1473 K时,非晶基体中富Ta相尺寸细小且弥散分布,并促进B2-CuZr相异质形核细化,得到了尺寸更细小、分布更均匀的核壳混杂增强结构。细小均匀的增强相可有效阻碍非晶基体中主剪切带的快速扩展,复合材料的力学性能得到大幅提高,断裂强度达到2439 MPa,塑性应变为11.6%。

等温锻造对CNTs/SiC_(p)混杂增强铝基复合材料力学性能的影响

强韧性匹配是金属基复合材料需解决的关键问题,强度的提升往往导致韧性损失,而混杂增强铝基复合材料可以综合各组元的优点,起到同时增强的协同混杂效应。为探索等温锻造工艺对混杂增强铝基复合材料力学性能的影响,采用真空烧结工艺制备了CNTs/SiC_(p)混杂增强Al-Cu-Mg铝合金复合材料,其CNT和SiC的质量分数分别为0.7%和10%,分别在450℃、460℃、470℃进行了80%变形量的等温锻造加工,研究了等温锻造对复合材料微观组织和力学性能的影响规律。结果表明混杂增强铝基复合材料经过等温锻造加工后的塑性相比烧结态锭坯发生明显上升,材料经470℃等温锻造后同比具有最好的综合力学性能,相比烧结态锭坯的抗拉强度提升了48%,延伸率提升了260%。等温锻造后,组织中的絮状相及细长形SiC颗粒在垂直于锻造方向上发生流线型分布,对材料的拉伸力学性能起到了强化作用。本研究为后续新型高性能铝基复合材料的开发与应用提供一定理论支撑。

传递矩阵法在计算输流管路高频振动时的稳定性改进

传递矩阵法(transfer matrix method,TMM)是研究结构振动时常用的计算方法,但在计算大跨度输流管路高频横向振动时,TMM存在数值不稳定的现象,制约了其进一步应用。基于无量纲化计算结果得到的子单元划分准则的全局传递矩阵法(global transfer matrix method,GTMM)、混合能传递矩阵法(hybrid energy transfer matrix method,HETMM)和结合变精度算法的传递矩阵法(variable precision algorithm-transfer matrix method,VPA-TMM)等三种方法解决了这一问题。GTMM是最常用的TMM计算稳定性改进方法;HETMM系首次从层状介质中的波传播计算扩展到管路系统的振动分析领域,计算矩阵的维度和形式不随子单元数的变化而变化,计算时间最短;VPA-TMM无需进行子单元划分,可以看作是从根源上解决了TMM的长跨度高频计算失稳问题,但计算时间会大幅度增加。

混合监测方法在桥梁静载试验中的应用

为了缓解桥梁健康监测系统成本与测点数量之间的矛盾,获得更加全面的监测信息,探索了一种将实测数据与数值模型相结合的混合监测方法。首先通过适当假设将经典的结构平衡方程进行简化,再从有限元模型中提取结构柔度矩阵,并由实测数据反算出等效荷载,最后将其带回原方程计算所需的结构响应。研究结果表明:该方法实现了从部分响应数据到全局响应数据的扩展,且计算效率较高,可避免反复的有限元分析。混合监测技术对结构响应的计算有较高的精度,计算得到的响应与实际响应误差均在10%以内。

基体配比对VIHPS制备GO-CF/EP复合材料微观组织与形状记忆性能的影响

碳纤维混杂增强复合材料由于具有重量轻、可设计性强等诸多优点,广泛用于汽车、海洋、航空航天等行业.根据固化剂与环氧树脂的配比化学原理,计算出石墨烯-碳纤维混杂增强树脂基(GO-CF/EP)复合材料的最佳配比为1∶5,并采用真空浸渗热压成型工艺(VIHPS)制备1∶2~1∶7共六个配比的试样,结合形状记忆性能测试及微观形貌的观察,得到固化剂与环氧树脂实际最佳配比.实验结果表明,GO-CF/EP复合材料性能主要取决于体系中交联度的大小,交联度越大,复合材料的形状记忆性能越好,微观组织形貌也较理想.当基体配比为1∶5时,GO-CF/EP复合材料体系中交联度最大,微观形貌呈现均匀致密的状态,形状固定率最大,为95.90%;形状回复率最大,为95.40%;形状回复时间最短,为80.30 s;形状回复力最大,为9.48 N.当基体配比为1∶2或1∶7时,固化剂过量或不足,交联度较小,微观组织形貌中有大量的基体聚集区,其形状记忆性能下降,形状固定率及回复率也相应减小,分别为82.99%,81.66%,81.91%,78.75%;形状回复力分别只有5.20 N和5.50 N.