INVESTIGATION IN REDUCING EXHAUST EMISSIONS FROM TWO STROKE MOTORCYCLES

Test results of reducing two stroke motorcycle emissions with new type carburettors and electronic fuel injection systems are presented. Analyses and comparison between different systems are discussed. The adoption of electronically controlled injection and corresponding electronic control technique is an effective measure of prolonged vitality to improve emissions from two stroke motorcycles. Suggestions about the strategic steps of China′s motorcycle emission control are proposed.

Stability of Cu-Mn bimetal catalysts based on different zeolites for NO_x removal from diesel engine exhaust

Cu–Mn bimetal catalysts were prepared to remove nitrogen oxides(NOx)from diesel engine exhaust at low temperatures.At a Cu/Mn ratio of 3:2,the NOx conversions at 200°C reached 65%and 90%on Cu–Mn/ZSM‐5 and Cu–Mn/SAPO‐34,respectively.After a hydrothermal treatment and reaction in the presence of C3H6,the activity of Cu–Mn/SAPO‐34 was more stable than that of Cu–Mn/ZSM‐5.No obvious variations in the crystal structure or dealumination were observed,whereas the physical structure was best maintained in Cu–Mn/SAPO‐34.The atomic concentration of Cu on the surface of Cu–Mn/SAPO‐34 was quite stable,and the consumption of octahedrally coordinated Cu2+could be recovered.Conversely,the proportion of octahedrally coordinated Cu2+on the surface of Cu–Mn/ZSM‐5 significantly decreased.Therefore,besides the structure,the redox cycle between Cu+and octahedrally coordinated Cu2+played an important role in the stability of the catalysts.

A Cascaded Discharge plasma—Adsorbent Technique for Engine Exhaust Treatment

A cascaded system of electrical discharges (non-thermal plasma) andadsorption process was investigated for the removal of oxides of Nitrogen (NO_x) and totalhydrocarbons (THC) from an actual diesel engine exhaust. The non-thermal plasma and adsorptionprocesses were separately studied first and then the cascaded process was studied. In this study,different types of adsorbents were used. The NO_x removal efficiency was higher withplasma-associated adsorption (cascaded) process compared to the individual processes and the removalefficiency was found almost invariant in time. When associated by plasma, among the adsorbentsstudied, activated charcoal and MS-13X were more effective for NO_x and THC removal respectively.The experiments were conducted at no load and at 50 % load conditions. The plasma reactor was keptat room temperature throughout the experiment, while the temperature of the adsorbent reactor wasvaried. A relative comparison of adsorbents was discussed at the end.

Injection of N-Radicals into Diesel Engine Exhaust Treated by Plasma for Improved NO_x Removal: A Feasibility Study

Reported in this paper is a feasibility study on the injection of plasma induced N radicals for the abatement of NO and NOx present in the actual diesel exhaust. The radical laden diesel exhaust was further treated by discharge plasma in a dielectric barrier discharge reactor. N radicals were produced in a separate plasma reactor filled with BaTiO3 pellets and were then injected into the treatment zone, There was a significant improvement in the efficiency when the radicals were injected compared to that when there was no radical injection. The efficiency of NOx removal at 0 load with plasma alone was 14% whereas with the injection of N radicals it went up to 38%, The results of the experiments conducted at different loads are discussed,

Effect of fin attachment on thermal stress reduction of exhaust manifold of an off road diesel engine

The effect of fin attachment on the thermal stress reduction of exhaust manifold of an off road diesel engine(Komatsu HD325-6) was investigated.For doing this,coupled thermo-fluid-solid analysis of exhaust manifold of the off road diesel engine was carried out.The thermal analysis,including thermal flow,thermal stress,and the thermal deformation of the manifold was investigated.The flow inside the manifold was simulated and then its properties including velocity,pressure,and temperature were obtained.The flow properties were transferred to the solid model and then the thermal stresses and the thermal deformations of the manifold under different operating conditions were calculated.Finally,based on the predicted thermal stresses and thermal deformations of the manifold body shell,two fin types as well as body shell thickness increase were applied in the critical induced thermal stress area of the manifold to reduce the thermal stress and thermal deformation.The results of the above modifications show that the combined modifications,i.e.the thickness increase and the fin attachment,decrease the thermal stresses by up to 28% and the contribution of the fin attachment in this reduction is much higher compared to the shell thickness increase.

Discharge Plasma Assisted Adsorbents for Exhaust Treatment: A Comparative Analysis on Enhancing NO_x Removal

An analysis has been made on the discharge plasma coupled with an adsorbent system for NOx removal. The cascaded plasma-adsorbent system may be perceived as a better alternative for the existing adsorbent-based abatement system in the industry. In this study the exhaust is sourced from a diesel generator set. It was observed that better NO removal in a plasma reactor can be made possible by achieving higher average fields and subsequent NO2 removal can be improved using an adsorbent system connected in cascade with the plasma system. The paper describes various findings pertaining to these comparative analyses.

Removal of Nitrogen Oxides in Diesel Engine Exhaust by Plasma Assisted Molecular Sieves

This paper reports the studies conducted on removal of oxides ofnitrogen (NOx) from diesel engine exhaust using electrical dischargeplasma combined with adsorbing materials such as molecular sieves.This study is being reported for the first time. The exhaust is takenfrom a diesel engine of 6 kW under no load conditions. Thecharacteristic behavior of a pulse energized dielectric barrierdischarge reactor in the diesel exhaust treatment is reported. TheNOx removal was not significant (36/100) when the reactor without anypacking was used.

Enhanced Performance of Discharge Plasma in Raw Engine Exhaust Treatment-Operation under Different Temperatures and Loads

This paper reports improved performance of discharge plasma in raw engine exhaust treatment. For the purpose of investigation, both filtered and raw diesel engine exhaust were separately treated by the discharge plasma. In raw exhaust environment, the discharge plasma exhibits a superior performance with regard to NOx removal, energy consmnption and formation of by-products. In this study, experiments were conducted at conditions of different temperatures and loads.

Effect of exhaust gas recirculation and intake pre-heating on performance and emission characteristics of dual fuel engines at part loads

Achieving simultaneous reduction of NOx,CO and unburned hydrocarbon(UHC) emissions without compromising engine performance at part loads is the current focus of dual fuel engine research.The present work focuses on an experimental investigation conducted on a dual fuel(diesel-natural gas) engine to examine the simultaneous effect of inlet air pre-heating and exhaust gas recirculation(EGR) ratio on performance and emission characteristics at part loads.The use of EGR at high levels seems to be unable to improve the engine performance at part loads.However,it is shown that EGR combined with pre-heating of inlet air can slightly increase thermal efficiency,resulting in reduced levels of both unburned hydrocarbon and NOx emissions.CO and UHC emissions are reduced by 24% and 31%,respectively,The NOx emissions decrease by 21% because of the lower combustion temperature due to the much inert gas brought by EGR and decreased oxygen concentration in the cylinder.

Unfiltered Diesel Engine Exhaust Treatment by Discharge Plasma: Effect of Soot Oxidation

A cascaded system of electrical discharges (Non-thermal plasma), catalyst andadsorption process was investigated for the removal of oxides of nitrogen (NO_x) and carbonmonoxide (CO) from a Diesel engine raw exhaust. The three processes were separately studied first,and then the cascaded processes, namely plasma-catalyst and plasma-adsorbent, were investigated. Inthis paper main emphasis was laid on the effect of carbonaceous soot oxidation on the plasmatreatment process. While the cascaded plasma-catalyst process exhibits a higher CO removal, thecascaded plasma-adsorbent process exhibits a higher NO_x removal. The experiments were conductedunder no-load. The plasma and adsorbent reactors were kept at room temperature throughout theexperiment while the catalyst reactor was kept at 200℃ / 300℃.

Modeling the Effect of Variable Timing of the Exhaust Valves on SI Engine Emissions for Greener Vehicles

The problem with fixed valve timing that the valve train is set by the automaker for peak efficiency running at a specific point in the engine’s operating range. When the vehicle is moving slower or faster than this ideal operating point the engine’s combustion cycle fails to properly burn the air/fuel mixture leading to considerably compromised engine performance and wastes fuel. Variable Valve Timing (VVT) is a solution developed to overcome this engine deficiency, dynamically altering the valve's opening and closing for optimal performance at any speed. The intension in this work is to contribute towards pursuing the development of variable valve timing (VVT) for improving the engine performance. This investigation covers the effect of exhaust valve opening (EVO), and closing (EVC) angle on engine performance and emissions. The aim is to optimize engine power and brake specific fuel consumption (BSFC) where the effect of engine speed has also been considered. Power, BMEP, BSFC, NO, and CO were calculated and presented to show the effect of varying valve timing on them for all the valve timing cases. The calculations of engine performance were carried out using the simulation and analysis engineering software: LOTUS”, and engine emissions were calculated using “ZINOX” program. Sensitivity analysis shows that the reduction of 10% of (EVO) angle gave a reduction of around 2.5% in power and volumetric efficiency, also a slight increase in nitrogen oxide (NO) and carbon monoxide (CO), while a 10% decrease in (EVC) causes around 1% improvement in Power. The effects of different (VVT) from the simulations are analyzed and compared with those in the reviewed literature.

Study of Pulsed Plasma in a Crossed Flow Dielectric Barrier Discharge Reactor for Improvement of NO_x Removal in Raw Diesel Engine Exhaust

Improved performance of plasma in raw engine exhaust treatment is reported. A new type of reactor referred to as of cross-flow dielectric barrier discharge （DBD） was used, in which the gas flow is perpendicular to the corona electrode. In raw exhaust environment, the cross-flow （radial-flow） reactor exhibits a superior performance with regard to NOx removal when compared to that with axial flow of gas. Experiments were conducted at different flow rates ranging from 2 L/min to 25 L/min. The plasma assisted barrier discharge reactor has shown encouraging results in NOx removal at high flow rates.

Design and optimization of exhaust gas aftertreatment system for a heavy-duty diesel engine

Diesel engines meeting the latest emission regulations must be equipped with exhaust gas aftertreatment system,including diesel oxidation catalysts(DOC),diesel particulate filters(DPF),and selective catalytic reduction(SCR).However,before the final integration of the aftertreatment system(DOC+DPF+SCR)and the diesel engine,a reasonable structural optimization of the catalytic converters and a large number of bench calibration tests must be completed,involving large costs and long development cycles.The design and optimization of the exhaust gas aftertreatment system for a heavy-duty diesel engine was proposed in this paper.Firstly,one-dimensional(1D)and threedimensional(3D)computational models of the exhaust gas aftertreatment system accounting for the structural parameters of the catalytic converters were established.Then based on the calibrated models,the effects of the converter’s structural parameters on their main performance indicators,including the conversion of various exhaust pollutants and the temperatures and pressure drops of the converters,were studied.Finally,the optimal design scheme was obtained.The temperature distribution of the solid substrates and pressure distributions of the catalytic converters were studied based on the 3D model.The method proposed in this paper has guiding significance for the optimization of diesel engine aftertreatment systems.

Optimizing the Exhaust System of Marine Diesel Engines to Improve Low-speed Performances and Cylinder Working Conditions

Proper design of exhaust systems in marine high-power turbocharged diesel engines can contribute to improve the low-speed performance of these engines and make the working conditions of the cylinders more uniform.Here a high-power marine 16-cylinder V-type turbocharged diesel engine is simulated using the GT-Power software.The results reveal the differences induced by different exhaust system structures,such as an 8-cylinder-inpipe exhaust system with single/double superchargers and a 4-cylinder-in-pipe exhaust system with a single supercharger.After a comparative analysis,the 8-cylinder type with double superchargers is determined to be the optimal solution,and the structure of the exhaust system is further optimized.The simulations show that the optimized maximum exhaust temperature difference among cylinders is reduced by 66%.Finally,the simulation results and the optimized performance of the designed exhaust system are verified through experiments.

Engine Performance and Exhaust Emissions of Peanut Oil Biodiesel

The engine performance and exhaust emissions of biodiesel produced from peanut oil must be evaluated to assess its potential as an alternative diesel fuel. In this study, two diesel engines rated at 14.2 kW (small) and 60 kW (large) were operated on pure peanut oil biodiesel (PME) and its blends with a reference diesel (REFDIESEL). Results showed that comparable power and torque were delivered by both the small and large engines when ran on pure PME than on REFDIESEL while brake-specific fuel consumption (BSFC) was found to be higher in pure PME. Higher exhaust concentrations of nitrogen oxides (NOx), carbon dioxide (CO2) and total hydrocarbons (THC) and lower carbon monoxide (CO) emissions were observed in the small engine when using pure PME. Lower CO2, CO and THC emissions were obtained when running the large engine with pure PME. Blends with low PME percentage showed insignificant changes in both engine performance and exhaust emissions as compared with the reference diesel. Comparison with soybean biodiesel indicates similar engine performance. Thus, blends of PME with diesel may be used as a supplemental fuel for steady-state non-road diesel engines to take advantage of the lubricity of biodiesel as well as contributing to the goal of lowering the dependence to petroleum diesel.

Application of Space-time Conservation Element and Solution Element Method in Intake and Exhaust Flows of High Power Density Diesel Engine

A one-dimensional pipe flow model of single-cylinder diesel engine is established to investigate the intake and exhaust flow characteristics of diesel engine in the condition of high power density(HPD).A space-lime conservation element and solution element(CE/SE)method is used to derive the discrete equations of the partial differential equation for the intake and exhaust systems.The performance parameters of diesel engine with speed of 2100 r/min are simulated.The simulated results are in accordance with the experimental data.The effect of increased power density on charging coefficient is analyzed using a validated model.The results show that the charging coefficient is slowly improved with the increase in intake pressure,and is obviously reduced with the increase in engine speed.

Jet Noise Reduction of Double-Mixing Exhaust System

A jet noise reduction technique by using the external chevron nozzle with lobed mixer in the double-mixing exhaust system is investigated under cold conditions.The computations of jet field and the experiments of noise field are conducted with scaled model of high-bypass-ratio turbofan engine mixing exhaust system composed of external chevron nozzle with lobed mixer.The computational results indicate that comparing with the baseline nozzle with lobed mixer,the external chevron nozzle with lobed mixer increases mixing of jet and ambient air near the nozzle exit.The experimental results show that the external chevron nozzle with lobed mixer has better jet noise reduction at low frequencies,and this reduction rises with the increase of chevron bend angle.The experimental results also show that the external chevron nozzle with lobed mixer has sound pressure level(SPL)increase which is not obvious at high frequencies.With chevron bend angle increasing,SPL has relatively marked increase at 60°(directivity angle measured from upstream jet axis)and little fluctuations at 90°and 150°.The external chevron nozzle with lobed mixer has overall sound pressure level(OASPL)reduction in varying degrees at 60°and 150°,but it has little OASPL increase at 90°.

EXPERIMENTAL INVESTIGATION ON TWO- DIMENSIONAL UNSTEADY COLD FLOW IN MPC EXHAUST MANIFOLD

The gas flow in exhaust manifolds has much effect on scavenge, pumping loss and exhaust energy utilization of turbocharged diesel engines. This paper presented experimental investigation on two dimensional unsteady flow in MPC(modular pulse converter) exhaust manifold model. The pressure and velocity distributions in six sections of the manifold model were measured when the diesel engine was motored. The probe with slitted sleeve was used to determine flow direction. The experimental results show that velocity distributions vary with place and time; the pressure traces at different points of the same section are not different obviously.

Optimization and Evaluation of a Vehicular Exhaust Heat Recovery System

Exhaust waste heat recovery system based on organic Rankine cycle(ORC)has been considered as an effective method to achieve energy conservation and emissions reduction of engine.The performance of adiesel engine with an on-board ORC exhaust heat recovery system was evaluated through simulations in this study.The combined system was optimized through controlling the exhaust gas mass flow rate entering the ORC system.The models of the engine with ORC system were developed in GT-suite and Simulink environment.The validation results showed high accuracy of the models.The performance of the system recovering heat from different exhaust gas mass flow rates was evaluated.The comparative analysis of the performance between the optimized and un-optimized system was also presented.The results indicated that the exhaust gas mass flow rate had significant effects on the system performance.Integration with the onboard ORC system could effectively improve the engine power performance.The power output of the engineORC combined system with optimization had further improvement,and the maximum improvement could reach up to 1.16 kW.

Parallel personal measurements of diesel engine exhaust and crystalline silica using dual sampling port

Diesel engine exhaust(DEE) and crystalline silica exposures occur simultaneously in the mining industry,and occupational sampling campaigns can be time-and cost-consuming. The authors evaluated a dualport system for simultaneous sampling of DEE and crystalline silica in laboratory and field conditions.Laboratory tests evaluated the operation of pumps during 8 h sampling and the intensity of the flow variation for various filter loading conditions and for different modes of operation. Field validation was performed in an underground mine. Pumps operated in constant flow or constant pressure modes.Tests in constant flow mode showed that when the flowrate increased on one side of the system, it decreased on the opposite side according to the loading intensity. Tests in constant pressure mode showed that flowrates systematically decreased when using loaded cassettes. However, the higher the backpressure setting, the lower the flow variation was. Flow variations during field tests were generally within the acceptable ±5% range. However, significant flow variations were identified in higher concentrations. A significant negative correlation was found between flowrate variation and total carbon concentration. While the majority of tests support the use of the dual-port for evaluating concomitant exposures, results highlight the possibility of filter overloading as a cause of flowrate changes.