初始组织对低碳钢IQ&P工艺残留奥氏体及力学性能的影响

采用双相区再加热-淬火-碳配分(IQ&P)工艺,研究初始组织为铁素体+珠光体的IQ&P-Ⅰ多相钢和初始组织为马氏体的IQ&P-Ⅱ多相钢的组织形貌、残留奥氏体及力学性能。结果表明:初始组织为铁素体+珠光体的IQ&P-Ⅰ多相钢室温组织中,铁素体和马氏体基本呈块状分布,块状残留奥氏体存在于铁素体与马氏体界面处,薄膜状只存在于马氏体内的板条之间,且残留奥氏体含量较少,TRIP效应不明显,其抗拉强度为957 MPa,伸长率只有20%,强塑积为19905.6MPa·%。初始组织为马氏体的IQ&P-Ⅱ多相钢中铁素体和马氏体大多呈灰黑色的板条状或针状,且细小的针状马氏体均匀地分布在铁素体基体上,残留奥氏体只以薄膜状平行分布在铁素体基体上,体积分数达到了13.2%,且具有较高的稳定性,TRIP效应较明显,强塑积达到21560MPa·%,可以获得强度和塑性的良好结合。

低碳钢IQ&P工艺下元素配分行为及对组织性能影响

采用双相区再加热-淬火-碳配分(IQ&P)工艺,研究了双相区不同等温时间下低碳钢中元素配分行为,并分析其对组织形貌、残余奥氏体及力学性能的影响。结果表明:在IQ&P工艺中,在750℃随等温时间的延长,Mn元素向逆转奥氏体内富集现象逐渐明显,等温时间超过300s后,C元素在两相之间的配分效果不随时间的延长而改变;在750℃等温处理过程中,原奥氏体晶界生成块状逆转奥氏体,马氏体板条界间生成针状逆转奥氏体;随等温时间的延长,钢的最终组织中针状铁素体体积分数不断减小,而块状及针状马氏体体积分数不断增大,同样残余奥氏体体积分数也不断增大;在C、Mn元素的综合作用下,钢的抗拉强度不断增大,断后伸长率先减小而后增大,等温1800s时,钢的强塑积达到最大值21GPa%。

线性调频宽带PD雷达的数字IQ处理方法研究

建立了宽带PD雷达信号处理过程的数学模型,提出了高重频宽带线性调频脉冲多卜勒雷达信号的波形设计要求,以及一种单通道低采样率数字IQ处理方法。理论分析与仿真结果表明,该方法相对于传统脉冲多卜勒雷达所采用的高采样率单通道直接中频采样IQ处理方法具有更好的信号能量积累性能。

基于Matlab的p-q法与ip-iq法仿真分析

针对p-q法和ip-iq法的谐波电流检测效果的比较,由于两种检测方法都是首先检测出原电流基波分量,再与原电流做差得到原电流谐波分量,因此可以通过计算检测出的基波电流中的谐波含量或畸变率来比较两种方法的检测性能。在接有非线性负载的系统中,通过控制电压源的电压波形,在(0.8-0.9)s时间段内产生标准正弦电压,在(0.9-1.0)s时间段内产生的畸变电压,利用p-q法和ip-iq法分别对同一检测点进行谐波电流检测。通过Matlab软件仿真试验,在(0.8-0.9)s时间段内利用p-q法和ip-iq法测得的基波电流的畸变率分别为1.72%和2.04%,在(0.9-1.0)s时间段内利用p-q法和ip-iq法测得的基波电流的畸变率分别为32.73%和4.39%。从而得出结论:在检测点处电压无畸变时,两种方法的检测性能都比较好,基波电流畸变率低,误差小;当电压发生畸变时,p-q法检测性能变差,基波电流畸变率变高,而ip-iq法检测性能无明显变化,适用范围更广。

Automatic IQ Phase Calibration Design in a 2.4GHz Direct Conversion Receiver

An automatic IQ phase calibration method implemented in a 2.4GHz direct conversion receiver is proposed. It uses a delay locked loop （DLL） with a proposed quadrature phase detector to greatly reduce the phase error. The receiver is fabricated in a 0.18μm CMOS process. Measurements show that the IQ phase error can be calibrated within 1°,which satisfies the system requirement.

Executive function impairments in high IQ children and adolescents with ADHD

Objective: To demonstrate that high IQ children and adolescents diagnosed with ADHD tend to suffer from executive function (EF) impairments that: a) can be identified with a combination of standardized measures and normed self-report data;and b) occur more frequently in this group than in the general population. Method: From charts of 117 children and adolescents aged 6 to 17 years with high IQ ( ≥ 120) who fully met DSM-IV diagnostic criteria for ADHD, data on 8 normed measures of executive function (EF) were extracted: IQ index scores for working memory and processing speed, a standardized measure of auditory verbal memory, and 5 clusters of the Brown ADD Scale, a normed, age-graded rating scale for ADHD-related executive function impairments in daily life. Significant impairment was computed for each individual relative to age-appropriate norms for each measure and comparisons were made to base-line rates in the general population. Results: Sixty-two percent of participants were significantly impaired on at least 5 of these 8 markers of EF. Chi-square comparisons of scores from these high IQ participants were significantly different (p < 0.001) from standardization norms for each of the eight EF measures. Conclusions: High IQ children and adolescents with ADHD, despite their cognitive strengths, tend to suffer from significant impairments of executive functions that can be assessed with these measures;incidence of these impairments is significantly greater than in the general population. These results are fully consistent with data on high IQ adults diagnosed with ADHD.

Design of Quenching Process for Large-sized AISI P20 Steel Block Used as Plastic Die

For large-sized AISI P20 steel block used as plastic die with a thickness of more than 200 mm, appropriate quenching processes are the key to obtain much thick hardened layer. In this paper, different quenching processes of AISI P20 steel block such as oil quenching, direct water quenching, water quenching with precooling and water quenching with pre-cooling and self-tempering were numerically investigated by computer simulation based on the detailed discussion on the mathematical models of quenching processes including partial differential equations of heat transfer, thermal physical properties, latent heat, heat transfer coefficient and calculation of phase transformation, The results show that the water quenching with pre-cooling and self-tempering process can not only effectively avoid quenching cracks, but also obtain deeper harden depth than oil quenching.

Source rupture process of the 2015 Gorkha, Nepal Mw7.9 earthquake and its tectonic implications

On 25 April, 2015, an Mw7.9 earthquake occurred in Nepal, which caused great economic loss and casualties. However, almost no surface ruptures were observed. Therefore, in order to interpret the phenomenon, we study the rupture process of the earthquake to seek answers. Inversion of teleseismic body-wave data is applied to estimate the rupture process of the 2015 Nepal earthquake. To obtain stable solutions, smoothing and non-negative constraints are introduced. 48 teleseismic stations with good coverage are chosen. Finite fault model is established with length and width of 195 km and 150 km, and we set the initial seismic source parameters referring to CMT solutions. Inversion results indicate that the focal mechanism of this earthquake is a thrust fault type, and the strike, dip and rake angle are in accordance with CMT results. The seismic moment is 0.9195 ×10^（21）Nm（Mw7.9）, and source duration is about 70s. The rupture nucleated near the hypocenter and then propagated along the dip direction to the southeast, and the maximum slip amounts to 5.2 m. Uncertainties on the amount of slip retrieved by different inversion methods still exist, the overall characteristics are inconsistent. The lack of shallow slip during the 2015 Gorkha earthquake implies future seismic hazard and this region should be paid more attention to.

Processing Mechanism of Chinese Verbal Jokes:Evidence from ERP and Neural Oscillations

The cognitive processing mechanism of humor refers to how the system of neural circuitry and pathways in the brain deals with the incongruity in a humorous manner. The past research has revealed different stages and corresponding functional brain activities involved in humor-processing in terms of time and space dimensions, highlighting the effects of the time windows of about 400 ms, 600 ms, and 900 ms. However, much less is known about humor processing in light of the frequency dimension. A total of 36 Chinese participants were recruited in this experiment, with Chinese jokes, nonjokes, and nonsensical sentences used as the stimuli. The experimental results showed that there were significant differences among conditions in the P200 effect, which signified that the incongruity detection had already been integrated and perceived at about 200 ms, prior to the semantic integration at about 400 ms. This pre-processing is specific to Chinese verbal jokes due to the simultaneous involvement of both orthographic and phonologic parts in processing Chinese characters. The analysis on the frequency dimension indicated that beta’s power particularly reflected the characteristics of different stages in Chinese verbal humor processing. Jokes’ and nonsensical sentences’ relative power changes on the beta band ranked significantly higher than that of nonjokes at about 200 ms, which suggested the existence of more difficulties in meaning construction in pre-processing the incongruities. This indicated a continuity between the analysis of event related potential (ERP) components and neural oscillations and revealed the key role of the beta frequency band in Chinese verbal joke processing.

miR-506-3p通过靶向IQGAP1基因抑制甲状腺癌细胞增殖、迁移和侵袭的体外研究

目的探讨miR-506-3p靶向IQ结构域GTP酶激活蛋白(IQGAP)1调控甲状腺癌细胞增殖、迁移和侵袭的分子机制。方法采用qRT-PCR和Western印迹检测甲状腺癌细胞SW579、FTC-133、KAT-18和正常甲状腺上皮细胞TEC中miR-506-3p、IQGAP1 mRNA和IQGAP1蛋白的表达;建立miR-506-3p过表达或IQGAP1抑制表达的SW579细胞株。采用噻唑蓝(MTT)法检测细胞增殖活力,Transwell法检测细胞迁移和侵袭能力,Western印迹检测细胞周期蛋白(Cyclin)D1、P21、P27、基质金属蛋白酶(MMP)-2、MMP-9和MMP-14蛋白表达水平。采用双荧光素酶报告基因实验验证miR-506-3p对IQGAP1的靶向作用。结果与正常甲状腺上皮细胞TEC相比,甲状腺癌细胞SW579、FTC-133和KAT-18中miR-506-3p表达显著降低,而IQGAP1表达显著升高。miR-506-3p过表达或IQGAP1抑制表达均可抑制SW579细胞的增殖、迁移和侵袭。IQGAP1是miR-506-3p的靶基因,miR-506-3p可负向调控IQGAP1表达。IQGAP1过表达可显著逆转miR-506-3p对SW579细胞的增殖、迁移和侵袭的抑制作用。结论miR-506-3p可通过下调IQGAP1表达抑制甲状腺癌细胞的增殖、迁移和侵袭。

A process model on P2P lending

Background:Online peer-to-peer lending(P2P lending)is booming as the popularity of e-finance.To develop a conceptual model for the P2P lending process is great valuable for managers to tack the issues of marketing,management and operation.Methods:In this paper,we focus on the P2P lending process model and provide a comparative analysis comparing with traditional bank loan process.Results:Firstly,our model shows that the information flow in P2P lending is more frequent and transparent.Secondly,the model reveals that P2P lending uses a quite different credit audition method,which relies on information and the decision model in the P2P systems.Thirdly,the loan management is not complete normally in P2P lending,because most P2P companies do not have the post-loan records of borrowers.Conclusions:These findings inspire future studies and practices on P2P lending process and key technologies.

Fuzzy Controller Based 3Phase 4Wire Shunt Active Filter for Mitigation of Current Harmonics with Combined p-q and Id-Iq Control Strategies

As more and more variable frequency drives (VFDs), electronic ballasts, battery chargers, and static Var compensators are installed in facilities, the problems related to harmonics are expected to get worse. As a result Active power filter (APF) gains much more attention due to excellent harmonic compensation. But still the performance of the active filter seems to be in contradictions with different control strategies. This paper presents detailed analysis to compare and elevate the performance of two control strategies for ex-tracting reference currents of shunt active filters under balanced, un-balanced and non-sinusoidal conditions by using Fuzzy controller. The well known methods, instantaneous real active and reactive power method (p-q) and active and reactive current method (id-iq) are two control methods which are extensively used in active filters. Extensive Simulations are carried out with fuzzy controller for both p-q and Id-Iq methods for different voltage conditions and adequate results were presented. Simulation results validate the superior per-formance of active and reactive current control strategy (id-iq) with fuzzy controller over active and reactive power control strategy (p-q) with fuzzy controller.

CATHODIC PROCESS AND WEAR RESISTANCE OF ELECTRO-DEPOSITED RE-Ni-W-P-SiC COMPOSITE COATING

Cathodic deposition current density of the composite coatings increases when SiC par-ticles and rare earth (RE) were added in the bath, which is profitable for Ni- W-P alloy to deposit in the cathod, forming Ni-W-P-SiC and RE-Ni-W-P-SiC composite coatings. On the contrary, the addition of PTFE in the bath decreases cathodic deposition current density of the coatings. The current density increases a little when the amount of RE is 7-9g/l; however, the current density increases greatly when the amount of RE is increased to 11-13g/l. Bui ij the amount of RE is raised further, the current density decreases. Hardness and wear resistance of RE-Ni-W-P-SiC composite coating have been studied, and the results show that the hardness and wear resistance of RE-Ni-W-P-SiC composite coating increase with increasing heat treatment tempera-ture, which reach peak values at 400℃; while the hardness and wear resistance of the coating decrease with the rise of heat treated temperature continuously.

Effect of Planting Eucalyptus Trees on Runoff Depth and Its Processes of Forestland Natural Watersheds

The runoff and runoff process of Eucalyptus plantations natural watershed were studied to provide guidance for scientific evaluation of water conservation capacities of Eucalyptus plantations,compared with the Pinus massoniana forest natural watershed. The runoff volumes of Eucalyptus plantations and P. massoniana forest natural watersheds were continuously monitored using the small watershed runoff monitoring method and the automatic data collection devices from August,2013 to December,2016,and effects of heavy rainfall and continuous rainfall on the runoff process were studied. Results showed that the annual runoff coefficient of Eucalyptus plantations natural watershed was 0. 050,and 55. 4% lower than P. massoniana forest（ 0. 112）,with the difference being significant（ P 〈 0. 01）. Total runoff duration,time of maximum runoff lagging behind rainfall peak,and runoff duration caused by a heavy rainfall process（ amounting to 147. 5 mm） between the two kinds of forest watersheds were significant different,those of Eucalyptus plantations were 35. 6 mm,0. 2 h and 13. 8 h,respectively,while those of P. massoniana forest were28. 5 mm,0. 7 h and 35. 5 h,respectively. Eucalyptus plantations natural watershed produced only 4-days runoff,and runoff depth amounted to3. 8 mm with a 7-days continuous precipitation process of rainfall with 125. 0 mm,while P. massoniana forest natural watershed produced continuously 13-days runoff,and the runoff depth was 10. 1 mm. In conclusion,water conservation capacity of Eucalyptus plantations is obviously lower than P. massoniana forest.

Study on Function of Rare Earth During Producing Phosphate Fertilizer by Wet Process

The impacts of the Rare Earth (RE) on the contents of available Phosphorus (P) and the physical character of the calcium superphosphate produced by the wet process on the basis of simulating the consumption of concentrated sulphuric acid, the slurry concentration and the cure conditions in different wet process were studied in laboratory, and the results show that adding RE into different wet process does not raise available P, but changes its physical character,for example, the composite is loose and the color is offwhite.

Investigation on a Non-cyanide Plating Process of Ni-P Coating on Magnesium Alloy AZ91D

In this research we presented a non-cyanide plating process of Ni-P alloy coating on Mg alloy AZ91D. By applying a new process flow of electroless nickel plating in which zinc coating is used as transition of Ni-P coating on Mg alloy AZ91D, the process of copper transition coating plated in the cyanides bath can be replaced. A new bath composed of NiSO4 was established by orthogonal test. The results show that zinc transition coating can increase the adhesion and protect the Mg alloy substrate from the bath corrosion. The optimal plating bath composition is NiSO4·6H2O 20 g/L, NaH2PO2·H2O20g/L and C6H8O7·H2O 2.5 g/L, and optimal bath acidity and optimal plating temperature are pH 4.0 and 95℃, respectively. The present process flow is composed of ultrasonic cleaning→alkaline cleaning→acid pickling→activation→double immersing zinc→electroplating zinc→electroless nickel plating→passivation treatment. The present non-cyanide process of electroless nickel plating is harmless to our surroundings and Ni-P coating on Mg alloy AZ91D produced by present process possesses good adhesion and corrosion resistance.

ON CONVERGENCE OF A GENERALIZED P AL INTERPOLATION PROCESS

Let f∈C[-1,1]and R. (r≥1 ) be the reneralized Pal iner polation polynomials satisf ying the conditions Rn, where{xk} are the roots of n-th Jacobi polynomial Pn and are the roots of In this paper,we prove that Rn holds uniformly on [0,1].

Development of high elongation steels by quenching and partitioning process

Based upon the composition of C-Si-Mn,four types of transformation induced plasticity（ TRIP） steels with different contents of Si and M n were designed,which are subjected to quenching and partitioning（ Q＆P）processes with variable austenitizing temperatures. The as-treated steels exhibits good combination of high strength and substantial elongation. In particular,with austenitizing at 820 ℃,0. 18C-1. 8Si-2. 2M n（ %） steel and0. 18C-1. 8Si-2. 5M n（ %） steel possessed high elongation（ more than 20%） with the tensile strength over 1000 M Pa. The microstructures of the as-treated steels were obtained by scanning electron microscope,the volume fraction and carbon content of retained austenite has been quantified by X-ray diffraction. The designed Q＆P processed steels contained a multiphase microstructure including ferrite,lath martensite,and retained austenite. The volume fraction and carbon content of those steels were higher,which was treated by Q＆P processes with austenitizing at 820 ℃. Due to the TRIP effect during the deformation process,retained austenite gives better stability as well as effectively improves the formability of steels with slightly decreasing the strength,contributing to overall better performance.

A NOTE ON SAMPLE PATH PROPERTIES OF l^p-VALUED GAUSSIAN PROCESSES

The a.s. sample path properties for l p valued Gaussian processes with stationary increments under some more general conditions are established.

CMT+P焊接行为及其AE特征频率

为了研究冷金属与脉冲复合焊(cold metal transfer and pulse,CMT+P)的焊接行为,使用PCI数据采集卡、高速相机、红外成像仪及声发射采集系统对焊接过程进行同步监测.发现脉冲射滴过渡发生前,焊机输出电流突增,同时焊丝尖端释放猛烈电弧光,随后熔滴滴入焊道,熔池温度增加,声发射(acoustic emission,AE)信号显示出1个波峰.发生CMT短路过渡时,焊机输出电流同时为焊丝熔化和焊丝伸出提供能量,待到焊丝尖端接触基板瞬间形成短路,熔池温度持续降低,AE信号微弱,伴随着熔滴因过热收缩而爆断,熔滴短路过渡完成.对AE信号进行离散傅里叶变换(discrete Fourier transform,DFT)后,可通过特征频率对CMT+P各个周期及阶段进行过程识别.结果表明,575 kHz和415 kHz可作为脉冲电弧周期和CMT短路周期的特征频率,推断180 kHz是脉冲电弧的特有频率,575 kHz的频率则是基础电弧提供,415 kHz处的频率则在CMT短路接触瞬间产生.