Efficient placement technology of proppants based on structural stabilizers

Fiber is highly escapable in conventional slickwater,making it difficult to form fiber-proppant agglomerate with proppant and exhibit limited effectiveness.To solve these problems,a novel structure stabilizer(SS)is developed.Through microscopic structural observations and performance evaluations in indoor experiments,the mechanism of proppant placement under the action of the SS and the effects of the SS on proppant placement dimensions and fracture conductivity were elucidated.The SS facilitates the formation of robust fiber-proppant agglomerates by polymer,fiber,and quartz sand.Compared to bare proppants,these agglomerates exhibit reduced density,increased volume,and enlarged contact area with the fluid during settlement,leading to heightened buoyancy and drag forces,ultimately resulting in slower settling velocities and enhanced transportability into deeper regions of the fracture.Co-injecting the fiber and the SS alongside the proppant into the reservoir effectively reduces the fiber escape rate,increases the proppant volume in the slickwater,and boosts the proppant placement height,conveyance distance and fracture conductivity,while also decreasing the proppant backflow.Experimental results indicate an optimal SS mass fraction of 0.3%.The application of this SS in over 80 wells targeting tight gas,shale oil,and shale gas reservoirs has substantiated its strong adaptability and general suitability for meeting the production enhancement,cost reduction,and sand control requirements of such wells.

Study on Compound Stabilizer Formulation for Mango Juice with Skin

[Objectives]The effects of stabilizers such as sodium carboxymethyl cellulose,pectin,sodium alginate and xanthan gum on the stability of mango juice with skin were discussed using mango as the raw material.[Methods]The formula and stability of mango beverage with skin were studied using mango juice with skin as the raw material.Four stabilizers,including pectin,sodium alginate and sodium carboxymethyl cellulose,were added to improve the stability of the juice.Based on single factor experiments and a response surface experiment,the stability model of mango juice was established to determine the best compound stabilizer.[Results]According to an orthogonal experiment on the stability of mango juice with skin,the optimum technical parameters were as follows:sodium carboxymethyl cellulose 0.20%,xanthan gum 0.08%,sodium alginate 0.18%,and pectin 0.14%,with which the optimal suspension stability was 69.12%.The optimum technical parameters from the response surface experiment were as follows:sodium carboxymethyl cellulose 0.199%,pectin 0.1185%,sodium alginate 0.163%,and xanthan gum 0.077%,with which the suspension stability was 70.32%.It was found that the stability of mango juice with skin obtained by the response surface experiment was better than that by the orthogonal experiment,and the order of factors affecting the stability of mango was sodium alginate(C)>sodium carboxymethyl cellulose(A)>pectin(D)>xanthan gum(B).[Conclusions]The formula of compound stabilizer for mango juice was optimized by the orthogonal experiment and the response surface method,providing a theoretical basis for the actual production of mango juice with skin.

Assessment of Cement-Lime as Stabilizer on Mud Bricks

The aim of this study was to evaluate the compressive strength of clay bricks and their stability to water absorption by inserting stabilizers such as lime and cement of 0%, 4%, 6%, 8%, 10%, 12% to 14%. Spectrometric analysis was used to characterize the various stabilizers and the clay used, and tests of resistance and water absorption were also carried out. The clay was found to be an aluminosilicate (15.55% to 17.17% Al2O3 and 42.12% to 44.15% SiO2). The lime contains 90.84% CaO and the cement has 17.80% SiO2, 3.46% Al2O3, 2.43% Fe2O3 and 58.47% CaO in the combined form of tricalcium silicate, dicalcium silicate, tricalcium aluminate and ferro-tetra calcium aluminate. The results showed that the insertion of locally available stabilizers (lime and cement) improved the strength of the material by almost 80% when the lime was increased from 0% to 14% for 14 days. For compressed cement, a 65% increase in strength was observed under the same conditions. Strength increases with drying time, with a 52% increase in strength at 28 days compared to 14 days. Furthermore, compressed cement bricks have a more compact structure, absorbing very little water (32%). In view of all these results, cement appears to be the best stabilizer, and compression improves compressive strength and reduces water absorption.

Robust adaptive precision motion control of tank horizontal stabilizer based on unknown actuator backlash compensation

Backlash nonlinearity inevitably exists in the actuator of tank horizontal stabilizer and has adverse effect on the system control performance,however,how to effectively eliminate its effect remains a pending issue.To solve this problem,a robust adaptive precision motion controller is presented in this paper to address uncertainties and unknown actuator backlash of tank horizontal actuator.The controller handles the modeling uncertainties including parameter uncertainties and unmodeled disturbances by integrating adaptive feedforward compensation and continuous nonlinear robust law.Based on the backstepping method,a smooth backlash inverse model is constructed by combining the adaptive idea.Meanwhile,the unknown backlash parameters of the system can be approximated through the parameter adaptation,and the impact of the actuator backlash nonlinearity is effectively compensated via the inverse operation,which can availably improve the tracking performance.Moreover,the adaptive law can update the disturbance ranges of tank horizontal stabilizer online in real time,which enhances the feasibility in practical engineering applications.Furthermore,the stability analysis based on Lyapunov function shows that with the existence of unmodeled disturbances and unknown actuator backlash,the designed controller guarantees excellent asymptotic output tracking performance.Extensive comparative results verify the effectiveness of the proposed control strategy.

Synthesis,crystallographic characterization,and potential application of fullerene anisole derivatives as nitrocellulose stabilizer

A series of fullerene anisole derivative stabilizers was synthesized by nucleophilic substitution reaction using hexachlorofullerene and benzyl alcohol as raw materials to extend the service duration of nitrocellulose(NC)-based propellants.Single-crystal X-ray diffraction,nuclear magnetic resonance,highresolution mass spectrometry,Fourier transform infrared(FT-IR)spectroscopy,and UV-Vis spectroscopy were used to characterize the structures of the synthesized fullerene anisole derivative stabilizers.Methyl violet,differential scanning calorimetry test,isothermal weight loss,vacuum stability test,and adiabatic accelerated test were used to study their compatibility with NC and their ability to stabilize NC.The results show that the designed and synthesized novel fullerene anisole derivative stabilizer has good compatibility with NC,and their overall stabilizing effects on NC are better than those of the traditional stabilizers,diphenylamine(DPA),and N,N’-dimethyl-N,N’-diphenylurea(C2).The stabilizing effects was ranked as:3b>2d>2a>2c>C2>2b>DPA>NC.In addition,FT-IR analysis and electron spin resonance spectroscopy were applied to explore the stability mechanism of fullerene-based stabilizers to NC.The results reveal that the new fullerene stabilizer can adsorb and effectively eliminate the nitrogen oxide free radicals generated by NC degradation;therefore,it can forbid the autocatalytic degradation of NC and stabilize NC.

Production of Corn (Zea mays) Starch and Cassava (Manihot esculenta) Starch and Their Application as Yogurt Stabilizer

The present study evaluated the stabilizing effect of starch produced from corns and cassava on the stability of cow milk yogurt. A sample of both corn and cassava starch was selected and used in the yogurt making as stabilizers. The yogurt samples have been analyzed for their WHC, syneresis and protein content. The yogurt with no added starch has found to have very low WHC and high syneresis compared to other samples. The yogurt made with the addition of corn starch as a stabilizer was highly accepted than the yogurt with cassava starch and the yogurt without starch. The findings from this study provide an alternative to add the value of local corns and cassava.

Development of a Thermal Fogger-specific Sedimentation Stabilizer

In order to solve the drifting away of thermal fog droplets during thermal spraying and the incompatibility between fog droplet carrier and conventional com- mercial agro-chemicals, the fog droplet carrier, surfactant, condensation nucleus ma- terial and antifreeze, dispersant, thickener and defoamer were screened and assem- bled to develop a thermal fog sedimentation stabilizer in this study, thereby provid- ing technical support for application and promotion of thermal spraying technology in pest and disease control in crops.

SYNTHESIS AND CHARACTERIZATION OF NEW STABILIZERS WITH OPTIMAL MOLECULAR WEIGHT

Over 2 x 10(8) tons of polymers are produced every year, and a large portion of polymers faces the degradation problem. There are many effective methods to protect polymers against degradation and the addition of stabilizers to polymer remains the most convenient and effective way of enhancing polymer life and performance. In this article, a series of effective stabilizers with optimal molecular weight (MW), including common, monomeric and polymeric stabilizers (antioxidant and light stabilizer) were synthesized using isocyanation, controlled isocyanation, hydrosilylation, epoxide addition, macroreaction of stabilizing functional compounds and polymerization of monomeric stabilizers. The structure and performance of these new stabilizers were characterized by using IR, NMR, MS, UV-spectra, XPS and elemental analysis. The current development of stabilizer synthesis was also reviewed.

Study on Mechanism of Rare Earth PVC Stabilizer

Rare earth compounds can be used as PVC thermal stabilizers. According to the infrared spectra of the mixture of PVC and some stearates, the mechanism of stabilization of different stearates was studied. The specialty of rare earth stabilizers was found. They can change the conformation of PVC and restrain the elimination of HCl. From this aspect, the unique synergetic effect with other stabilizers of rare earth compounds can be explained.

Application of New-type Soil Stabilizer Q2 in Subgrade Construction

The research analyzed characters of soil stabilizer and detailed the solidification mechanism.Furthermore,new type soil stabilizer Q2 was used in a base of Beijing Vocational College of Agriculture and a solidified road with length of 250 m,width of 4 m and thickness of 0.25 m were constructed.The road was tested with an agricultural truck and subgrade tolerance to freezing was tested also.It is suggested that new type soil stabilizer would reduce construction cost of road,protect environment,and reduce construction period,with high value of application.

Mechanical Behaviors of ZrO_2-Al_2O_3 Ceramic Composites with Y_2O_3 as Stabilizer

The ZrO2-Al2O3 ceramic composites were prepared by appropriate techniques with commercial ZrO2 and Al2O3 powders as raw materials and Y2O3 as stabilizer. The results indicate that with the introduction of Al2O3 into the ZrO2 matrix where the quantity of additive Y2O3 is 3.5% (mole fraction), the growth of ZrO2 grains is efficiently inhibited, which helps the ZrO2 grains exist in a metastable tetragonal manner; thus higher strength and toughness are acquired. When the content of alumina is 20% (mass fraction), the bending strength and fracture toughness of the composites are 676.7 MPa and 10 MPa·m1/2 respectively, the mechanical behaviors are close to those prepared with ZrO2 and Al2O3 powders synthesized through wet chemical approach. The mechanical behaviors of the composites are well improved owing to the dispersion toughening of alumina grains and phase transformation toughening of zirconia grains.

Power system stabilizer design using hybrid multi-objective particle swarm optimization with chaos

A novel technique for the optimal tuning of power system stabilizer (PSS) was proposed,by integrating the modified particle swarm optimization (MPSO) with the chaos (MPSOC).Firstly,a modification in the particle swarm optimization (PSO) was made by introducing passive congregation (PC).It helps each swarm member in receiving a multitude of information from other members and thus decreases the possibility of a failed attempt at detection or a meaningless search.Secondly,the MPSO and chaos were hybridized (MPSOC) to improve the global searching capability and prevent the premature convergence due to local minima.The robustness of the proposed PSS tuning technique was verified on a multi-machine power system under different operating conditions.The performance of the proposed MPSOC was compared to the MPSO,PSO and GA through eigenvalue analysis,nonlinear time-domain simulation and statistical tests.Eigenvalue analysis shows acceptable damping of the low-frequency modes and time domain simulations also show that the oscillations of synchronous machines can be rapidly damped for power systems with the proposed PSSs.The results show that the presented algorithm has a faster convergence rate with higher degree of accuracy than the GA,PSO and MPSO.

Lithium:from mood stabilizer to putative cognitive enhancer

The monovalent cation lithium,whose introduction in psychiatry dates back at the end of the 1940s,remains the first-line agent in the management of patients with bipolar disorder（BD）.It is effective in the treatment of moderate-to-severe acute mania,prophylactic for recurrent manic and depressive episodes,and reduces the risk of suicide.

Development and evaluation of an electropositive wellbore stabilizer with flexible adaptability for drilling strongly hydratable shales

In order to overcome serious instability prob- lems in hydratable shale formations, a novel electropositive wellbore stabilizer （EPWS） was prepared by a new approach. It has good colloidal stability, particle size dis- tribution, compatibility, sealing property, and flexible adaptability. A variety of methods including measurements of particle size, Zeta potential, colloidal stability, contact angle, shale stability index, shale dispersion, shale swelling, and plugging experiments were adopted to characterize the EPWS and evaluate its anti-sloughing capacity and flexible adaptability. Results show that the EPWS has advantages over the conventional wellbore stabilizer （ZX-3） in particle size distribution, colloidal stability, inhibition, compatibil- ity, and flexible adaptability. The EPWS with an average particle size of 507 nm and an average Zeta potential of 54 mV could be stable for 147 days and be compatible with salt tolerant or positive charged additives, and it also exhibited preferable anti-sloughing performance to hydrat- able shales at 77, 100, and 120 ~C, and better compatibility with sodium bentonite than ZX-3 and KC1. The EPWS can plug micro-fractures and pores by forming a tight external mud cake and an internal sealing belt to retard pressure transmission and prevent filtrate invasion, enhancing hydrophobicity of shale surfaces by adsorption to inhibithydration. The EPWS with flexible adaptability to tem- perature for inhibition and sealing capacity is available for long open-hole sections during drilling.

Lift fin stabilizers based on data fusion with wavelet denoising technology

Fin stabilizers with fin-lift feedback control can shield the mapping error of calculation between the fin angle and fin lift force,which is in the fin stabilizer with fin-angle feedback control.In practice,there are some technical difficulties in lift fin stabilizers,such as lift force detection and lift force sensor installation,so it cannot achieve the good antirolling performance.Therefore,a fin stabilizer system with fin-lift/fin-angle integrated control is brought forward.Data fusion based on wavelet denoising technology is employed in the system,which combines lift with fin angle local information from two sensors with different frequency ranges in order to eliminate redundant and contradictory information,and using complementary information to obtain the relative integrity of the lift force signal.The system model is established in this paper,and the fusion signal and the antirolling performance of this model are simulated respectively.The result shows that the control system can meet the antirolling need in different sea situations.

Analysis of influence factors of unconfined compressive strength for composite soil stabilizer-stabilized gravel soil

In order to investigate the effect o f some factors on the unconfined compressive strength(UCS)for composite soil stabilizer-stabilized gravel soil(CSSSGS),the orthogonal test is adopted to set up the experimental scheme.Three levels o f each factor armconsidered to obtain the change laws o f UCS,in which the binder dosages are8%,10%,and12%;the curing times ae7,14and21d;the gradation nae0.3,0.35and0.4;and the degrees of compaction are95%,97%,and99%.The range analysis clearly indicates that the influence degree o f the four factors on UCS is in such an order:dosage,age,gradation,and degree o f compaction.The variance analysis shows that only the composite soil stabilizer dosage can significantly affect UCS.In road construction,the examination o f composite soil stabilizer dosage and base-course maintenance should be given much more attention to obtain satisfactory base-course strength,compared w ith gradation floating and the change of degree o f compaction.

High-frequency structure design and RF stability analysis of a 4-vane radio frequency quadrupole with pi-mode stabilizer loops

Compact accelerator-based neutron source facilities are garnering attention and play an important and expanding role in material and engineering sciences,as well as in neutron science education and training.Neutrons are produced by bombarding a low-energy proton beam onto a beryllium or lithium target.In such an acceleratorbased neutron source,a radio frequency quadrupole(RFQ)is usually utilized to accelerate a high-intensity proton beam to a few MeV.This study mainly covers the highfrequency structure design optimizations of a 4-vane RFQ with pi-mode stabilizer loops(PISLs)and its RF stability analysis.A 176 MHz RFQ accelerator is designed to operate at a 10%duty factor and could accelerate an80 mA proton beam from 65 keV to 2.5 MeV within a length of 5.3 m.The adoption of PISLs ensures high RF stability,eases the operation of the accelerator,and implies less stringent alignment and machining tolerances.

Encoding entanglement-assisted quantum stabilizer codes

We address the problem of encoding entanglement-assisted （EA） quantum error-correcting codes （QECCs） and of the corresponding complexity. We present an iterative algorithm from which a quantum circuit composed of CNOT, H, and S gates can be derived directly with complexity O（n2） to encode the qubits being sent. Moreover, we derive the number of each gate consumed in our algorithm according to which we can design EA QECCs with low encoding complexity. Another advantage brought by our algorithm is the easiness and efficiency of programming on classical computers.

A Meta-analysis of Mood Stabilizers for Alzheimer's Disease

The objective of this study was to assess the clinical evidence for or against mood stabilizers as a treatment for Alzheimer’s disease (AD).We searched 5 databases from their inception to January 2010.Five randomized clinical trials of mood stabilizers to treat human patients suffering from AD were included.These trials assessed the effectiveness of mood stabilizers as an adjunct treatment to conventional anti-dementia drugs on behavioral and psychological symptoms, especially on agitation.Methodological quality was assessed using the Jadad score.The results suggested a significant effect in favor of placebo on the Mini-Mental Status Examination [n=270, weight mean difference (WMD), -0.89; 95% confidence intervals (CIs) -1.69 to -0.09, P=0.03] and on the Neuropsychiatric Inventory total (NPI total) (n=51, WMD, 3.71; 95% CIs 0.15 to 7.26, P=0.04).There were no significant differences in change scores on total Brief Psychiatric Rating Scale (BPRS total), NPI/BPRS agitation, Cohen-Mansfield Agitation Inventory total and Physical Self Maintenance Scale between mood stabilizers and placebo.Only one of these studies was free of methodological limittions (Jadad score=5).In conclusion, based on the existing evidence, mood stabilizers are ineffective or even harmful as a treatment for AD.

Optimal and Robust Power System Stabilizers in a Multi Machine System

One method for eliminating oscillations in power systems is using stabilizers.By applying an appropriate control signal in the excitation system of a generator,a power system stabilizer improves the dynamic stability of power systems.However,the issue that is of high importance is the correct design of these stabilizers.These stabilizers must be designed to have proper performance when operating conditions change.When designed incorrectly,not only they do not improve the stability margin,but also increase the oscillations.In this paper,the robust design of power system stabilizers on a four-machine power system has been performed.For this purpose,the differential evolution algorithm has been used.The studies have been repeated as three scenarios by producing different loading conditions for the generators.The performances of the conventional stabilizer and the optimized one have been compared.Simulation results indicate that the designed robust stabilizer outperforms other stabilizers in different conditions and has damped the interarea and intra-area oscillation modes in the shortest time with minimum amplitude.