A simple and new point contact tungsten trioxide （WO3） sensor, which can be prepared by the oxidation of tungsten filaments via in-situ induction heating, likely detects low concentration （ppm level） environmental...A simple and new point contact tungsten trioxide （WO3） sensor, which can be prepared by the oxidation of tungsten filaments via in-situ induction heating, likely detects low concentration （ppm level） environmental pollutants such as NO2. X-ray diffraction （XRD） and field emission scanning electron microscopy （FE-SEM） were applied to characterize the phase and the microstructure of the samples, respec-tively. It was found that the synthesized WO3 films exhibited a monoclinic phase and were composed of hierarchical microcrystals and nanocrystals. The point contact WO3 sensor （W-WO3-W） showed rectifying characteristics and an ideal sensing performance of about 110 C. A single semicircle in Nyquist plots was recorded by electrochemical impedance spectroscopy （EIS） at a relatively low temperature of 150 C but faded away above 200 C, which revealed that the sensing process was governed by a determining factor, i.e., grain boundaries at the contact site.展开更多
Polypyrrole (PPy) films were prepared by multi-potential steps polymerization in an aqueous pyrrole solution, with lithium perchlorate and oxalic acid as supporting electrolytes. Morphology and structure of PPy films ...Polypyrrole (PPy) films were prepared by multi-potential steps polymerization in an aqueous pyrrole solution, with lithium perchlorate and oxalic acid as supporting electrolytes. Morphology and structure of PPy films were characterized by scanning electron microscopy (SEM) and X-ray diffraction (XRD). Electrochemical behaviors of PPy films were studied by cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS). The results show that multi-potential steps polymerization improves the conductivity of PPy films and large polymer films can be peeled off easily from the electrode without cracking. Lithium perchlorate and oxalic acid provide appropriate dopants for PPy polymerization. It was observed that the polymerization time and the current density have a crucial influence on the surface morphology of PPy films. Smooth and compact PPy films could be generated under long polymerization time and low current density. Multi-potential steps polymerization decreases the occurrence of peroxidation, which improves the conductivity of PPy films. The parameters for multi-potential steps polymerization have been optimized.展开更多
In this work, for the first time, photosensitive nanostructures with alternate semiconductor and magnetic oriented nematic molecular nanolayers were obtained. The established dependency on the ordering type of kinetic...In this work, for the first time, photosensitive nanostructures with alternate semiconductor and magnetic oriented nematic molecular nanolayers were obtained. The established dependency on the ordering type of kinetic and optical properties is deserving attention. For the first time, the notion of ＇rotary＇ polaron in such structures is introduced and microscopic model is created, which explains band structure transformation. The model is well coordinated with experimental optical data, which, at the same time, indicate the prospects of application of materials obtained due to the intercalation engineering for photoenergetics.展开更多
基金supported by the National Natural Science Foundation of China (Nos.NSAF10876017, NSAF10776017, and91023037)
文摘A simple and new point contact tungsten trioxide （WO3） sensor, which can be prepared by the oxidation of tungsten filaments via in-situ induction heating, likely detects low concentration （ppm level） environmental pollutants such as NO2. X-ray diffraction （XRD） and field emission scanning electron microscopy （FE-SEM） were applied to characterize the phase and the microstructure of the samples, respec-tively. It was found that the synthesized WO3 films exhibited a monoclinic phase and were composed of hierarchical microcrystals and nanocrystals. The point contact WO3 sensor （W-WO3-W） showed rectifying characteristics and an ideal sensing performance of about 110 C. A single semicircle in Nyquist plots was recorded by electrochemical impedance spectroscopy （EIS） at a relatively low temperature of 150 C but faded away above 200 C, which revealed that the sensing process was governed by a determining factor, i.e., grain boundaries at the contact site.
基金supported by the National Basic Research Program of China ("973"Program) (Grant No. 2011CB935701)the National Science Foundation for Post-doctoral Scientists of China (Grant No. 20100480251)
文摘Polypyrrole (PPy) films were prepared by multi-potential steps polymerization in an aqueous pyrrole solution, with lithium perchlorate and oxalic acid as supporting electrolytes. Morphology and structure of PPy films were characterized by scanning electron microscopy (SEM) and X-ray diffraction (XRD). Electrochemical behaviors of PPy films were studied by cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS). The results show that multi-potential steps polymerization improves the conductivity of PPy films and large polymer films can be peeled off easily from the electrode without cracking. Lithium perchlorate and oxalic acid provide appropriate dopants for PPy polymerization. It was observed that the polymerization time and the current density have a crucial influence on the surface morphology of PPy films. Smooth and compact PPy films could be generated under long polymerization time and low current density. Multi-potential steps polymerization decreases the occurrence of peroxidation, which improves the conductivity of PPy films. The parameters for multi-potential steps polymerization have been optimized.
文摘In this work, for the first time, photosensitive nanostructures with alternate semiconductor and magnetic oriented nematic molecular nanolayers were obtained. The established dependency on the ordering type of kinetic and optical properties is deserving attention. For the first time, the notion of ＇rotary＇ polaron in such structures is introduced and microscopic model is created, which explains band structure transformation. The model is well coordinated with experimental optical data, which, at the same time, indicate the prospects of application of materials obtained due to the intercalation engineering for photoenergetics.
