Efficient removal of Al(Ⅲ)and P507 from high concentration MgCl_(2)solution based on in-situ reaction strategy

For a highly efficient recycling of a wastewater containing a high concentration of MgCl_(2),Al(Ⅲ)and P507 were scheduled to be removed in advance.In this study,the in-situ removal of Al(Ⅲ)and P507 from a high concentration MgCl_(2)solution at different pH values and Al/P molar ratios was investigated.The results showed that P507 formed organic complexes of Al_(x)(OH)_y^(Z+)-P507 at pH of 2.0-4.0.At pH of 4.0-5.0,Al(Ⅲ)precipitated and transferred into Al(OH)_(3)with a flocculent amorphous morphology.Active sites on the Al(OH)_(3)surface enhanced the removal efficiency of P507.At pH of 6.0-6.5,Al(Ⅲ)and Mg(Ⅱ)formed layered crystalline Al(OH)_(3)and MgAl_(2)(OH)_(8with)small pore channels and fewer active sites,resulting in a reduced removal efficiency of P507.When the Al/P molar ratio exceeded 13 and the pH was between 4.0 and 5.0,the removal rates of both Al(Ⅲ)and P507 were higher than98%,while the concentration loss of Mg(Ⅱ)was only 0.2%-0.9%.

Dense copper azide synthesized by in-situ reaction of assembled nanoporous copper microspheres and its initiation performance

Copper azide with high density was successfully synthesized by in-situ reaction of nanoporous copper(NPC)precursor with HN_(3) gaseous.NPC with pore size of about 529 nm has been prepared by electroless plating using polystyrene(PS)as templates.The copper shells thickness of NPC was controlled by adjusting the PS loading amount.The effects of copper shell on the morphology,structure and density of copper azide were investigated.The conversion increased from 87.12%to 95.31%when copper shell thickness decrease from 100 to 50 nm.Meanwhile,the density of copper azide prepared by 529 nm NPC for 24 h was up to 2.38 g/cm^(3).The hollow structure of this NPC was filled by swelling of copper azide which guaranteed enough filling volume for keeping the same shape as well as improving the charge density.Moreover,HNS-IV explosive was successfully initiated by copper azide with minimum charge thickness of 0.55 mm,showing that copper azide prepared has excellent initiation performance,which has more advantages in the application of miniaturized explosive systems.

Microstructure and Properties of A IN Coating/Graphite Fabricated via In-situ Reaction

A novel method was used to fabricate AlN coating on graphite substrate. This approach included two steps： firstly, the emulsion composed of BN and anhydrous ethanol was sprayed on the surface of the graphite substrate; secondly, AlN coating was formed through the in-situ reaction of Al with the sprayed BN. The reaction was investigated by thermogravimetric-differential thermal analysis （TG-DTA）, and the phase composition in the synthetic process was characterized by X-ray diffraction （XRD）. Scanning electronic microscopy （SEM） was used to observe the morphology, and electron probe microanalysis （EPMA） was used to observe the distribution of the elements. The experimental results show that the AlN coating is dense and bonded with graphite tightly.

Microstructure and Mechanical Property of (TiNbTaZrHf)C Synthesized by In-situ Reaction

The(TiNbTaZrHf)C high entropy carbide(HEC)was successfully synthesized by complete commercial transition metal powders,obtained fine sintered bulks without additives by in-situ reaction element synthesis method.(TiNbTaZrHf)C bulk shows a face centered cubic rock salt structure with homogeneous single-phase FCC structure in composition and structure.The optimum sintering temperature is about 1900℃at which the best mechanical properties are obtained.The mechanical properties of(TiNbTaZrHf)C ceramic block are better than those of binary transition metal carbides,and it has obvious high entropy effect.Adding a small amount of Al as sintering additive,the mechanical properties of(TiNbTaZrHf)C ceramics continue to improve,the bending strength of the samples at each temperature is increased by at least 38%,and the highest is 486 MPa.The elastic modulus and hardness of the sample at 1900℃are also slightly increased by 4%and 14%,respectively.The above conclusions illustrate that the properties of high entropy ceramics are greatly improved by in-situ reaction sintering.

Microstructure and mechanical properties of Fe/NbC composite layer prepared by in-situ reaction

NbC ceramic surface-reinforced steel matrix composites were prepared by an in-situ reaction method at different temperatures(1,050℃,1,100℃and 1,150℃)for different times(1 h,2 h and 3 h).The phase constitution,microstructure and fracture morphology of NbC ceramic surface-reinforced steel matrix composites were analyzed by XRD,SEM and EDS,and the effects of the in-situ reaction temperature and time on the mechanical properties were systematically studied.The results indicate that the NbC reinforcement layer is formed through the reaction between Nb atoms and carbon atoms diffused from the steel matrix to the Nb plate.The thickness of this reinforcement layer increases as the reaction time prolongs.Additionally,an increase in reaction temperature results in a thicker reinforcement layer,although the rate of increase gradually decreases.The relationship among the thickness of the Nb C reinforcement layer,the reaction time and temperature was established by data fitting.The optimal tensile performance is achieved at 1,100℃for 1 h,with a tensile strength of 228 MPa.It is also found that the defects between the reinforcement layer and the steel matrix are related to reaction temperature.At 1,100℃,these defects are minimal.Fracture mostly occurs in the NbC reinforced layer of the composites,and the fracture mode is characterized by typical intergranular brittle fracture.

PARTICLES ANALYSIS OF Al_2O_3 PARTICLE REINFORCED ZL202 MATRIX COMPOSITES PREPARED BY IN-SITU REACTION

ZL202 matrix composite reinforced by Al2O3 particles was prepared by combining in-situ reaction and casting techniques. Particles' size in the composites was from 1 to 5 microns in diameter. X-ray diffraction analysis verified that the reinforcing particleswere δ-Al2O3 which belong to γ-Al2O3 series. The wetting angle between matrix andreinforcement was less than 90°. Energy spectrum analysis indicated that the reactionin bell cover pressing process took place not so completely as in flouring stir process. When the reaction was finished, the matrix was still ZL202 alloy in both.processes.

Oxidation of Dibenzothiophene in Model Diesel Using Hydroperoxide Generated via In-Situ Reaction of Octane with Oxygen

The potential of carrying out oxidative desulfurization(ODS) using oxygen as an oxidant was explored in this work. n-Octane firstly reacted with oxygen to produce hydroperoxides in-situ, which were then used as oxidants to oxidize the dibenzothiophene(DBT) in the absence of catalysts. The hydroperoxides generated in-situ were effective in oxidizing DBT to its corresponding dibenzothiophene sulfone(DBTO_2) which was characterized by FT-IR and ~1H-NMR. The removal rate of DBT could reached 98.4% under conditions covering a temperaure of 140℃, a rection duration of 4 h, and an oxygen partial pressure of 0.4 MPa. The influences of different hydrocarbon components in diesel on DBT removal were investigated. The results showed that cyclohexane and n-dodecane had no effect on the removal of DBT, but xylene had a slight negative effect on DBT removal. A possible oxidation mechanism was proposed and the concentration of hydroperoxides in both O_2-oxidized octane and model diesel were detected.

Layered structure of Ni-Al multi-layered metal-intermetallic composites fabricated by in-situ reactions

Systematical experiments were done at five temperature levels: （500 ℃,） （630 ℃,） （900 ℃,） （1 000 ℃） and （1 100 ℃） to illuminate the layer structure of the multi-layered metal-intermetallic composites of Ni-Al system that were fabricated by a previously reported simple and cost-effective method. The analysis of back scattering photos and XRD examination of specimens reveal that the look like single compound layer is composed of several different components. The primary phase produced during reaction is Ni2Al3 and there exists a like two-phase field between NiAl3 and Ni2Al3. The high temperature phases like NiAl and Ni3Al are also found at low temperature. The results indicate that the key driving force of in-situ reaction is not temperature, but the atom concentration.

Recent advances and key perspectives of in-situ studies for oxygen evolution reaction in water electrolysis

Electricity-driven water splitting to produce hydrogen is one of the most efficient ways to alleviate energy crisis and environmental pollution problems,in which the anodic oxygen evolution reaction(OER)is the key half-reaction of performance-limiting in water splitting.Given the complicated reaction process and surface reconstruction of the involved catalysts under actual working conditions,unraveling the real active sites,probing multiple reaction intermediates and clarifying catalytic pathways through in-situ characterization techniques and theoretical calculations are essential.In this review,we summarize the recent advancements in understanding the catalytic process,unlocking the water oxidation active phase and elucidating catalytic mechanism of water oxidation by various in-situ characterization techniques.Firstly,we introduce conventionally proposed traditional catalytic mechanisms and novel evolutionary mechanisms of OER,and highlight the significance of optimal catalytic pathways and intrinsic stability.Next,we provide a comprehensive overview of the fundamental working principles,different detection modes,applicable scenarios,and limitations associated with the in-situ characterization techniques.Further,we exemplified the in-situ studies and discussed phase transition detection,visualization of speciation evolution,electronic structure tracking,observation of reaction active intermediates,and monitoring of catalytic products,as well as establishing catalytic structure-activity relationships and catalytic mechanism.Finally,the key challenges and future perspectives for demystifying the water oxidation process are briefly proposed.

Highly mass activity electrocatalysts with ultralow Pt loading on carbon black for hydrogen evolution reaction

Pt-based nanocatalysts offer excellent prospects for various industries.However,the low loading of Pt with excellent performance for efficient and stable nanocatalysts still presents a considerable challenge.In this study,nanocatalysts with ultralow Pt content,excellent performance,and carbon black as support were prepared through in-situ synthesis.These~2-nm particles uniformly and stably dispersed on carbon black because of the strong s-p-d orbital hybridizations between carbon black and Pt,which suppressed the agglomeration of Pt ions.This unique structure is beneficial for the hydrogen evolution reaction.The catalysts exhibited remarkable catalytic activity for hydrogen evolution reaction,exhibiting a potential of 100 mV at 100 mA·cm^(-2),which is comparable to those of commercial Pt/C catalysts.Mass activity(1.61 A/mg)was four times that of a commercial Pt/C catalyst(0.37 A/mg).The ultralow Pt loading(6.84wt%)paves the way for the development of next-generation electrocatalysts.

Boosting Oxygen Evolution Reaction Performance on NiFe‑Based Catalysts Through d‑Orbital Hybridization

Anion-exchange membrane water electrolyzers(AEMWEs)for green hydrogen production have received intensive attention due to their feasibility of using earth-abundant NiFe-based catalysts.By introducing a third metal into NiFe-based catalysts to construct asymmetrical M-NiFe units,the d-orbital and electronic structures can be adjusted,which is an important strategy to achieve sufficient oxygen evolution reaction(OER)performance in AEMWEs.Herein,the ternary NiFeM(M:La,Mo)catalysts featured with distinct M-NiFe units and varying d-orbitals are reported in this work.Experimental and theoretical calculation results reveal that the doping of La leads to optimized hybridization between d orbital in NiFeM and 2p in oxygen,resulting in enhanced adsorption strength of oxygen intermediates,and reduced rate-determining step energy barrier,which is responsible for the enhanced OER performance.More critically,the obtained NiFeLa catalyst only requires 1.58 V to reach 1 A cm^(−2) in an anion exchange membrane electrolyzer and demonstrates excellent long-term stability of up to 600 h.

Preparation and wear properties of TiB_2/Al-30Si composites via in-situ melt reactions under high-energy ultrasonic field

TiB2/Al-30Si composites were fabricated via in-situ melt reaction under high-energy ultrasonic field. The microstructure and wear properties of the composite were investigated by XRD, SEM and dry sliding testing. The results indicate that TiB2 reinforcement particles are uniformly distributed in the aluminum matrix under high-energy ultrasonic field. The morphology of the TiB2 particles is in circle-shape or quadrangle-shape, and the size of the particles is 0.1-1.5μm. The primary silicon particles are in quadrangle-shape and the average size of them is about 10μm. Hardness values of the Al-30Si matrix alloy and the TiB2/Al-30Si composites considerably increase as the high energy ultrasonic power increases. In particular, the maximum hardness value of the in-situ composites is about 1.3 times as high as that of the matrix alloy when the ultrasonic power is 1.2 kW, reaching 412 MPa. Meanwhile, the wear resistance of the in-situ TiB2/Al-30Si composites prepared under high-energy ultrasonic field is obviously improved and is insensitive to the applied loads of the dry sliding testing.

Luminescent properties of Eu(OA)_3(TTA)/NBR composites prepared by in-situ reaction

Eu（OA）3（TTA） （OA=cis-9-octadecenoic acid, TTA=4,4,4-trifluoro-l-（2-thienyl）-l,3-butanedione） complexes （Eu- com- plexes） containing the ligand OA with long molecular chains were synthesized. The Eu（OA）3（TTA） complexes and peroxide were added into nitrile-butadiene rubber （NBR） by mechanical shearing to get the uncured composites. The cured composites were ob- tained by vulcanizing the uncured composites at high temperature. The in-situ reaction including polymerization and grafting of Eu-complex took place at the curing process, which was verified by Fourier transform infrared spectroscopy （FTIR） and X-ray dif- fraction （XRD）. Scanning electron microscopy （SEM） and transmission electron microscopy （TEM） observations showed the fine dispersion of Eu（OA）3（TTA） complex （Eu-complex） in the cured composites compared with the uncured ones. Fluorescent spectra and Judd-Ofelt parameters analysis revealed that the fluorescent intensity increased approximate linearly with the content of Eu- complex increasing due to the in-situ reaction and long molecular chains of OA. The fluorescent lifetime of composites was longer than that of original Eu-complexes.

Preparation and microstructure of in-situ(ZrB_2+Al_2O_3+Al_3Zr)_p/A356 composite synthesized by melt direct reaction

（ZrB2＋Al2O3＋Al3Zr）/A356 composites were synthesized by melt direct reaction from A356-（K2ZrF6＋KBF4＋Na2B4O7） system.The phase compositions and the microstructures of the as-prepared composites were investigated by XRD,SEM and TEM.The results show that the reinforcements are composed of ZrB2 and Al2O3 ceramic phase particles and Al3Zr intermetallic particles.The ZrB2 particulates are easy to join together to form some particle clusters and distribute along the α（Al） grain boundary.The morphologies of the ZrB2 particulates are in hexagon-shape with the size of about 50 nm.The TEM investigation results of Al3Zr indicate that Al3Zr grows in the form of facet with the length-diameter ratio of about 20.The morphologies of Al2O3 particles are in rectangular-shape and ellipsoidal-shape,with the size of about 0.1 μm.In addition,the interfaces of the matrix and particles are net and no interfacial outgrowth is observed.

Effects of hot-pressing parameters on microstructure and mechanical properties of composites synthesized by Al-TiO_(2) in-situ reaction

As a classic in-situ reaction, the Al-TiO_(2) reaction is expected to prepare aluminum matrix composites with high thermal stability.In this study, it was found that the preparation method of ensuring sufficient reaction using higher temperatures in previous studies was not conducive to acquiring optimized high-temperature strength. With the increase of hot-pressing temperature and the extension of holding time, the in-situ reaction became more thorough, but the strength of the composites first increased and then decreased. Coarsening of the microstructure at high temperatures would lead to degradation of strength and controlling the in-situ reaction process by the hot-pressing parameters could optimize the mechanical properties of the composites. Strengthening mechanisms at room and high temperatures were studied, and it was found that the load-transfer and Orowan strengthening mechanisms are the main strengthening effects at room temperature, while the pinning effect of fine particles became more crucial at elevated temperatures. As a result, the coarsening of the reinforcing phases was more detrimental to the hightemperature strength. Therefore, an insufficient in-situ reaction led to more excellent mechanical properties, and the composite hot-pressed at 605℃ and held for 2 h exhibited the highest strength, which was 367 MPa at room temperature and 170 MPa at 350℃.

Fabrication and mechanical properties of self-toughening ZrB2–SiC composites from in-situ reaction

Self-toughening ZrB2–SiC based composites are fabricated by in-situ reactive hot pressing.The effect of sintering additive content on the microstructure and mechanical properties of the composites is investigated.Microstructure observation found that the in-situ reactive hot pressing could promote the anisotropic growth of ZrB2 grains and the formation of interlocking microstructure.Such microstructure could improve the mechanical properties,especially,for the fracture toughness.The improved mechanical properties could be attributed to the self-toughening structure related to the ZrB2 platelets and the formed interlocking microstructure,which could trigger various toughening mechanisms such as grain pull-out,crack bridging,crack deflection,and crack branching,providing the main contribution to the high fracture toughness.

In-situ self-templated preparation of porous core-shell Fe_(1-x)S@N,S co-doped carbon architecture for highly efficient oxygen reduction reaction

Transition metal compound(TMC)/carbon hybrids,as prospering electrocatalyst,have attracted great attention in the field of oxygen reduction reaction(ORR).Their morphology,structure and composition often play a crucial role in determining the ORR performance.In this work,we for the first time report the successful fabrication of porous core-shell Fe_(1-x)S@N,S co-doped carbon(Fe_(1-x)S@NSC-t,t represents etching time)by a novel in-situ self-template induced strategy using Fe3O4 nanospheres and pyrrole as sacrificial self-template.The post-polymerization of pyrrole can be accomplished by the Fe^(3+)released through the etching of Fe_(3)O_(4) by HCl acid.Thus,the etching time has a significant effect on the morphology,structure,composition a nd ORR performance of Fe_(1-x)S@NSC-t.Based on the cha racterizations,we find Fe_(1-x)S@NSC-24 can realize effective and balanced combination of Fe_(1-x)S and NSC,possessing porous core-shell architecture,optimized structure defect,specific surface area and doped heteroatoms configurations(especially for pyridinic N,graphitic N and Fe-N structure).These features thus lead to outstanding catalytic activity and cycling stability towards ORR.Our work provides a good guidance on the design of TMC/carbon-based electrodes with unique stable morphology and optimized structure and composition.

In-situ monitoring of dynamic behavior of catalyst materials and reaction intermediates in semiconductor catalytic processes

Semiconductor photocatalysis, as a key part of solar energy utilization, has far-reaching implications for industrial, agricultural, and commercial development. Lack of understanding of the catalyst evolution and the reaction mechanism is a critical obstacle for designing efficient and stable photocatalysts. This review summarizes the recent progress of in-situ exploring the dynamic behavior of catalyst materials and reaction intermediates. Semiconductor photocatalytic processes and two major classes of in-situ techniques that include microscopic imaging and spectroscopic characterization are presented. Finally, problems and challenges in in-situ characterization are proposed, geared toward developing more advanced in-situ techniques and monitoring more accurate and realistic reaction processes, to guide designing advanced photocatalysts.

Reaction mechanism for in-situ β-SiAlON formation in Fe3Si–Si3N4–Al2O3 composites

In this work,Fe_3Si–Si_3N_4–Al_2O_3 composites were prepared at 1300°C in an N_2 atmosphere using fused corundum and tabular alumina particles,Al_2O_3 fine powder,and ferrosilicon nitride(Fe_3Si–Si_3N_4) as raw materials and thermosetting phenolic resin as a binder.The effect of ferrosilicon nitride with different concentrations(0wt%,5wt%,10wt%,15wt%,20wt%,and 25wt%) on the properties of Fe_3Si–Si_3N_4–Al_2O_3 composites was investigated.The results show that the apparent porosity varies between 10.3% and 17.3%,the bulk density varies from 2.94 g/cm^3 and 3.30 g/cm^3,and the cold crushing strength ranges from 67 MPa to 93 MPa.Under the experimental conditions,ferrosilicon nitride,whose content decreases substantially,is unstable;part of the ferrosilicon nitride is converted into Fe_2C,whereas the remainder is retained,eventually forming the ferrosilicon alloy.Thermodynamic assessment of the Si_5AlON_7 indicated that the ferrosilicon alloy accelerated the reactions between Si_3N_4 and α-Al_2O_3 fine powder and that Si in the ferrosilicon alloy was nitrided directly,forming β-Si Al ON simultaneously.In addition,fused corundum did not react directly with Si_3N_4 because of its low reactivity.

Microstructure and mechanism of in-situ Al_2O_(3(p))/Al nano-composites synthesized by sonochemistry melt reaction

The Al2O3（p）/Al nano-composites were fabricated from Al-K2ZrF6-Na2B4O7 system by sonochemistry in situ reaction. The fabrication mechanisms, including high intensity ultrasonic influence on microstructures and reinforcement particles-aluminum matrix interface, were investigated by X-ray diffraction （XRD）, scanning electron microscopy （SEM） and transmission electron microscopy （TEM）. The XRD results show that the component of the as-prepared composites is Al2O3 reinforcement. The SEM analysis results indicate that Al2O3 particles are uniformly distributed in the aluminum matrix. The TEM results show that the morphologies of Al2O3 particles present in nearly sphere-shape, the sizes are in the range of 20-100 nm, and the interfaces are net and no interfacial outgrowth is observed. Analysis with secondary development Image-J software shows that Al2O3 recoveries are firstly improved and then decreased with increasing ultrasonic power. When the power is 0.4 kW, the distribution is the best, and a maximum number of particles are obtained. The reaction mechanisms were investigated.