Graphene/Inconel 718 composites were innovatively synthesized through selective laser melting,and the mechanical and tribological performances of the grapheme-reinforced Inconel 718 matrix composites were evaluated.Th...Graphene/Inconel 718 composites were innovatively synthesized through selective laser melting,and the mechanical and tribological performances of the grapheme-reinforced Inconel 718 matrix composites were evaluated.The composite microstructures were characterized by XRD,SEM and Raman spectroscopy.The results show that selective laser melting is a viable method to fabricate Inconel 718 matrix composite and the addition of graphene nanoplatelets leads to a significant strengthening of Inconel 718 alloy,as well as the improvement of tribological performance.The yield strength and ultimate tensile strength of 1.0%graphene/Inconel 718 composites(mass fraction)are 42%and 53%higher than those of pure material,and the friction coefficient and wear rate are 22.4%and 66.8%lower than those of pure material.The decrease of fraction coefficient and wear rate is attributed to the improved hardness of composites and the formation of graphene nanoplatelet protective layer on the worn surfaces.展开更多
High entropy alloy(HEA) of Fe Co Ni Ti Al and Inconel 718 superalloy were firstly transient liquid phase(TLP) bonded by BNi2 filler due to the diffusion of Si and B in the filler to the base metals. The effects of bon...High entropy alloy(HEA) of Fe Co Ni Ti Al and Inconel 718 superalloy were firstly transient liquid phase(TLP) bonded by BNi2 filler due to the diffusion of Si and B in the filler to the base metals. The effects of bonding time on microstructure evolution and mechanical properties of the TLP joints were investigated.Owing to the complete isothermal solidification of the joints bonded for 30 min 120 min at 1100°C,no athermally solidified zones(ASZs) formed by eutectic phases were observed in the welded zone. Thus the TLP joints were only composed by the isothermally solidified zone(ISZ) and two diffusion affected zone(DAZ) adjacent to the dissimilar base metals and the negative effect of the ASZ on joint properties can be avoided. In addition, the increase of the bonding time can also make the Ti B2 borides precipitated in the DAZ near HEA and the brittle borides or carbides in the DAZ near IN718 alloy decrease and reduce the possibility of the stress concentration happened in the joints under loading. Therefore, the highest shear strength(632.1 MPa) of the TLP joints was obtained at 1100°C for 120 min, which was higher than that of the joint bonded for 30 min, 404.2 MPa. Furthermore, the extension of the bonding time made the fracture mechanism of the joint be transformed from the intergranular fracture to the transgranular fracture. However, as the brittle borides in the DAZ near IN718 can not be eliminated completely and refining of grains also happened in such region, all the TLP joints fractured inner the DAZ near IN718 alloy.展开更多
For improving the service performance of Inconel 718 alloy, especially used as a corrosion-resistant alloy for special environment, the microstructure and mechanical property of different carbon-containing Inconel 718...For improving the service performance of Inconel 718 alloy, especially used as a corrosion-resistant alloy for special environment, the microstructure and mechanical property of different carbon-containing Inconel 718 alloys were investigated by the Thermo-Calc software and experiments. The experimental results indicated that the mor- phology, distribution and types of carbides mainly existing in the form of MC＇were hardly influenced by solution treatment at 1050 ℃ for 1 h. The precipitation amount and particle size of carbides decreased with the decrease of carbon content, which was the main reason resulting in the increase of ductility and toughness. In addition, moving dislocation could be restrained by the precipitation of carbides. Therefore, the strength could benefit from the precip- itation strengthening of carbides when the precipitation of γ′/γ″ phase was not influenced by the precipitation of carbides.展开更多
Rotation angle of the laser scan direction between two adjacent layers is a key controlling parameter during the high-power (≥ 1 kW) laser powder bed fusion (HP-LPBF) process. This study investigates the influen...Rotation angle of the laser scan direction between two adjacent layers is a key controlling parameter during the high-power (≥ 1 kW) laser powder bed fusion (HP-LPBF) process. This study investigates the influences of rotation angles (θ = 0°, 45°, 90°, 105°) on the surface morphology, microstructure, and mechanical properties of Inconel 718 (IN718) alloy produced by HP-LPBF. Results show that adopting low rotation angles (e.g., 0° and 45°) is prone to relatively poor surface finish and lack-of-fusion defects, whereas adopting high rotation angles (e.g., 90° and 105°) induces smaller surface roughness and better relative density. Each case reveals a noticeable edge effect but the maximal heights witness a downward trend with the increase of rotation angle. There are some minor differences in the primary dendrite arm spacing and grain morphology by varying the rotation angles. Moreover, the tensile property is slightly enhanced as the rotation angle increases. The present work suggests that high rotation angles like 90° and 105° would probably be more favorable for the 1 kW HP-LPBF process than rotation angles with relatively low values.展开更多
基金Project supported by the Ganpo 555 Program for Leading Talents of Jiangxi Province,China
文摘Graphene/Inconel 718 composites were innovatively synthesized through selective laser melting,and the mechanical and tribological performances of the grapheme-reinforced Inconel 718 matrix composites were evaluated.The composite microstructures were characterized by XRD,SEM and Raman spectroscopy.The results show that selective laser melting is a viable method to fabricate Inconel 718 matrix composite and the addition of graphene nanoplatelets leads to a significant strengthening of Inconel 718 alloy,as well as the improvement of tribological performance.The yield strength and ultimate tensile strength of 1.0%graphene/Inconel 718 composites(mass fraction)are 42%and 53%higher than those of pure material,and the friction coefficient and wear rate are 22.4%and 66.8%lower than those of pure material.The decrease of fraction coefficient and wear rate is attributed to the improved hardness of composites and the formation of graphene nanoplatelet protective layer on the worn surfaces.
基金Project(52275371) supported by the National Natural Science Foundation of ChinaProject(2020YFA0714900) supported by the National Key R&D Program of China。
基金supported by the research fund of the State Key Laboratory of Solidification Processing(NWPU,China)(Grant No.2019-TS-09)the National Natural Science Foundations of China(Grant Nos.51975480,51575451,51475376 and U1737205)。
文摘High entropy alloy(HEA) of Fe Co Ni Ti Al and Inconel 718 superalloy were firstly transient liquid phase(TLP) bonded by BNi2 filler due to the diffusion of Si and B in the filler to the base metals. The effects of bonding time on microstructure evolution and mechanical properties of the TLP joints were investigated.Owing to the complete isothermal solidification of the joints bonded for 30 min 120 min at 1100°C,no athermally solidified zones(ASZs) formed by eutectic phases were observed in the welded zone. Thus the TLP joints were only composed by the isothermally solidified zone(ISZ) and two diffusion affected zone(DAZ) adjacent to the dissimilar base metals and the negative effect of the ASZ on joint properties can be avoided. In addition, the increase of the bonding time can also make the Ti B2 borides precipitated in the DAZ near HEA and the brittle borides or carbides in the DAZ near IN718 alloy decrease and reduce the possibility of the stress concentration happened in the joints under loading. Therefore, the highest shear strength(632.1 MPa) of the TLP joints was obtained at 1100°C for 120 min, which was higher than that of the joint bonded for 30 min, 404.2 MPa. Furthermore, the extension of the bonding time made the fracture mechanism of the joint be transformed from the intergranular fracture to the transgranular fracture. However, as the brittle borides in the DAZ near IN718 can not be eliminated completely and refining of grains also happened in such region, all the TLP joints fractured inner the DAZ near IN718 alloy.
文摘For improving the service performance of Inconel 718 alloy, especially used as a corrosion-resistant alloy for special environment, the microstructure and mechanical property of different carbon-containing Inconel 718 alloys were investigated by the Thermo-Calc software and experiments. The experimental results indicated that the mor- phology, distribution and types of carbides mainly existing in the form of MC＇were hardly influenced by solution treatment at 1050 ℃ for 1 h. The precipitation amount and particle size of carbides decreased with the decrease of carbon content, which was the main reason resulting in the increase of ductility and toughness. In addition, moving dislocation could be restrained by the precipitation of carbides. Therefore, the strength could benefit from the precip- itation strengthening of carbides when the precipitation of γ′/γ″ phase was not influenced by the precipitation of carbides.
文摘Rotation angle of the laser scan direction between two adjacent layers is a key controlling parameter during the high-power (≥ 1 kW) laser powder bed fusion (HP-LPBF) process. This study investigates the influences of rotation angles (θ = 0°, 45°, 90°, 105°) on the surface morphology, microstructure, and mechanical properties of Inconel 718 (IN718) alloy produced by HP-LPBF. Results show that adopting low rotation angles (e.g., 0° and 45°) is prone to relatively poor surface finish and lack-of-fusion defects, whereas adopting high rotation angles (e.g., 90° and 105°) induces smaller surface roughness and better relative density. Each case reveals a noticeable edge effect but the maximal heights witness a downward trend with the increase of rotation angle. There are some minor differences in the primary dendrite arm spacing and grain morphology by varying the rotation angles. Moreover, the tensile property is slightly enhanced as the rotation angle increases. The present work suggests that high rotation angles like 90° and 105° would probably be more favorable for the 1 kW HP-LPBF process than rotation angles with relatively low values.
