Fault diagnosis in neutral point indirectly grounded system basedon information fusion

In neutral point indirectly grounded systems, phase-to-ground fault is putting new demands on fault diagnosis technology. Information fusion is applied to detect the phase-to-ground fault, which integrates several sources of information, including line current, line voltage, zero sequence current and voltage, and quintic harmonic wave component. This method is testified through the simulation of Matlab. Simulation results show that the precision and reliability of the detection has been greatly increased.

Power Balance Consideration in the Design of Indirectly Driven Targets

A preliminary design for a heavy ion driver inertial fusion（HIDIF） target is presented. The effect of target material and dimensions on transfer efficiency and symmetrical irradiation in the hohlraum are investigated.The analysis led to the evaluation of optimal target materials and dimensions to achieve a positive power balance of an ICF power plant.The results show that the best choice is a high Z material for cavity wall materials and a low Z material for the capsule ablator.It is concluded that for achieving the highest transfer efficiency and best symmetrization we need an area ratio between 5≤A2/A1≤9.

From trees to fleas: masting indirectly affects flea abundance on a rodent host

Mast seeding causes strongfluctuations in populations of forest animals.Thus,this phenomenon can be used as a natural experiment to examine how variation in host abundance affects parasite loads.We investigatedfleas infesting yellow-necked mice in beech forest after 2 mast and 2 non-mast years.We tested 2 mutually exclusive scenarios:(1)as predicted by classical models of density-dependent transmission,an increase in host density will cause an increase in ectoparasite abundance(defined as the number of parasites per host),versus(2)an increase in host density will cause a decline inflea abundance(“dilution,”which is thought to occur when parasite population growth is slower than that of the host).In addition,we assessed whether masting alters the relationship between host traits(sex and body mass)andflea abundance.We found a hump-shaped relationship between host andflea abundance.Thus,the most basic predictions are too simple to describe ectoparasite dynamics in this system.In addition,masting modified seasonal dynamics offlea abundance,but did not affect the relationship between host traits andflea abundance(individuals with the highest body mass hosted the mostfleas;after controlling for body mass,parasite abundance did not vary between sexes).Our results demonstrate that pulses of tree reproduction can indirectly,through changes in host densities,drive patterns of ectoparasite infestation.

Modeling and analysis of oil shale refinery process with the indirectly heated moving bed

China is rich of oil shale as one of alternative fossil energy resources.The exploitation and utilization of oil shale are strategically important in alleviating the shortage of oil and gas resources in China.However,low utilization rate of raw material,low oil yield,and high content of heavy components in the oil are the main problems in current Fushun type oil shale refinery technology.An indirectly heated moving bed is developed to de-bottleneck Fushun type technology.The oil shale refinery process with the indirectly heated moving bed is modeled and simulated in this work.Based on the simulation,a techno-economic analysis is performed and compared with the conventional Fushun oil shale refinery process.Results show that:for a shale refinery of 3.0 Mt/y scale,375 t/h oil shale retorting requires 149.6 MW of heat,in which 60%of the heat is produced by combustion of the oil shale pyrolysis gas,while remaining 40%from the coal gasified gas.In consideration of investment and operation,the cost of product shale oil of the new process is 2636 CNY/t,which is 12%lower than that of the conventional Fushun refinery process.This benefit comes from higher utilization of raw material and oil yield of the new process.The competitive crude oil price of the indirectly heated moving bed refinery process is about 51$/bbl,while that of the Fushun refinery process is 58$/bbl.During 2017 year,the crude oil price fluctuates at around 50$/bbl,thus the new indirectly heated moving bed refinery process shows better economic competitiveness.

Multipartite entanglement generation with dipole induced transparency effect in indirectly coupled dipole-microcavity systems

We propose a feasible scheme of generating multipartite entanglement with the dipole induced transparency （D/T） effect in indirectly coupled dipole-microcavity systems. It is shown that the transmission spectrum is closely related with the interference of dipole-microcavity systems, and we can generate different classes of multi- partite entanglement, e.g., the Greenberger-Horne-Zeilinger state, the W state, and the Dicke state, of the di- pole emitters just by choosing an appropriate frequency of the incident photon. Benefiting from the DIT effect, the schemes may work in the bad or low-Q cavity regime only if the large Purcell factor of the dipole-microcavity system is fulfilled, and they are also insensitive to experimental noise, which may be feasible with present acces- sible technology.

Efficacy of fexuprazan compared with rebamipide in Korean patients with gastritis:A matching-adjusted indirect comparison

BACKGROUND Gastritis is one of the most frequently diagnosed diseases requiring medical treatment in South Korea.Fexuprazan,a novel potassium-competitive acid blocker,has been approved for treating gastritis and erosive esophagitis.Meanwhile,rebamipide is the most commonly used mucoprotective agent for acute and chronic gastritis in real-world settings in South Korea.However,there have been no studies comparing the efficacy of these two drugs yet.AIM To compare the efficacy of fexuprazan with that of rebamipide for acute and chronic gastritis.METHODS This was a matching-adjusted indirect comparison.Individual patient data from a phase III study of fexuprazan(10 mg BID)were compared with cumulative data from two matching studies of rebamipide(100 mg TID).Erosion improvement and healing rates were compared between two weeks of fexurapan,two weeks of rebamipide,and four weeks of rebamipide.The two main outcome variables were presented as percentages,and the risk differences(RD)and 95%confidence intervals(CI)were calculated for the relative treatment effects.RESULTS In the primary analysis,the erosion improvement and healing rates after a twoweek treatment with fexuprazan were 64.5%and 53.2%,respectively,while a twoweek treatment with rebamipide resulted in erosion improvement and healing rates of 43.6%(RD:21.0%;95%CI:9.6-32.3;P<0.01)and 35.6%(RD:17.6%;95%CI:6.1-29.2;P=0.003),respectively.In the additional analysis,the erosion improvement and healing rates for the two-week fexuprazan treatment(64.2%and 51.2%,respectively)were similar to those obtained during a four-week treatment with rebamipide(60.6%;RD:3.6%;95%CI:-9.8,17.0;P=0.600 and 53.5%;RD:-2.3%;95%CI:-16.1,11.5;P=0.744,respectively).CONCLUSION The two-week fexuprazan treatment was superior to the two-week rebamipide treatment and similar to the fourweek rebamipide treatment for patients with gastritis.

Recent Progresses of the DAMPE Mission

The DArk Matter Particle Explorer(DAMPE)is a space high-energy particle andγ-ray detector whose major scientific goals are the indirect detection of dark matter particles,the origin of cosmic rays and highenergyγ-ray astronomy.Since its successful launch in December 2015,the DAMPE has been operated smoothly in orbit for more than 8 years.The direct measurements of the boron-to-carbon and boron-to-oxygen flux ratios,and the proton+Helium spectrum up to 316 TeV have been obtained,revealing new spectral features with very high significances.The search results ofγ-ray spectral line and fractionally charged particles indicate a good potential of DAMPE for indirect dark matter detection and new physical discovery in space.The DAMPE measurements are expected to significantly advance our understanding of the fundamental problems in astroparticle physics.

Fracture propagation and evolution law of indirect fracturing in the roof of broken soft coal seams

Indirect fracturing in the roof of broken soft coal seams has been demonstrated to be a feasible technology.In this work,the No.5 coal seam in the Hancheng block was taken as the research object.Based on the findings of true triaxial hydraulic fracturing experiments and field pilot under this technology and the cohesive element method,a 3D numerical model of indirect fracturing in the roof of broken soft coal seams was established,the fracture morphology propagation and evolution law under different conditions was investigated,and analysis of main controlling factors of fracture parameters was conducted with the combination weight method,which was based on grey incidence,analytic hierarchy process and entropy weight method.The results show that“士”-shaped fractures,T-shaped fractures,cross fractures,H-shaped fractures,and“干”-shaped fractures dominated by horizontal fractures were formed.Different parameter combinations can form different fracture morphologies.When the coal seam permeability is lower and the minimum horizontal principal stress difference between layers and fracturing fluid injection rate are both larger,it tends to form“士”-shaped fractures.When the coal seam permeability and minimum horizontal principal stress between layers and perforation position are moderate,cross fractures are easily generated.Different fracture parameters have different main controlling factors.Engineering factors of perforation location,fracturing fluid injection rate and viscosity are the dominant factors of hydraulic fracture shape parameters.This study can provide a reference for the design of indirect fracturing in the roof of broken soft coal seams.

Behavior of exciton in direct−indirect band gap Al_(x)Ga_(1−x)As crystal lattice quantum wells

Excitons have significant impacts on the properties of semiconductors.They exhibit significantly different properties when a direct semiconductor turns in to an indirect one by doping.Huybrecht variational method is also found to influence the study of exciton ground state energy and ground state binding energy in Al_(x)Ga_(1−x)As semiconductor spherical quantum dots.The Al_(x)Ga_(1−x)As is considered to be a direct semiconductor at AI concentration below 0.45,and an indirect one at the concentration above 0.45.With regards to the former,the ground state binding energy increases and decreases with AI concentration and eigenfrequency,respectively;however,while the ground state energy increases with AI concentration,it is marginally influenced by eigenfrequency.On the other hand,considering the latter,while the ground state binding energy increases with AI concentration,it decreases with eigenfrequency;nevertheless,the ground state energy increases both with AI concentration and eigenfrequency.Hence,for the better practical performance of the semiconductors,the properties of the excitons are suggested to vary by adjusting AI concentration and eigenfrequency.

Omental fibroma combined with right indirect inguinal hernia masquerades as a scrotal tumor: A case report

BACKGROUND The most common causes of scrotal enlargement in patients include primary tumor of the scrotum,inflammation,hydrocele of the tunica vaginalis,and indirect inguinal hernia;scrotal enlargement caused by external tumors of the scrotum is rare.The patient had both a greater omentum tumor and an inguinal hernia,and the tumor protruded into the scrotum through the hernia sac,which is even rarer.Moreover,omental tumors are mostly metastatic,and primary omental fibroma is rare.CASE SUMMARY Here,we report a rare case of a 25-year-old young man with scrotal enlargement and pain for 3 months.Preoperative examination and multidisciplinary discu-ssions considered intra-abdominal tumor displacement and inguinal hernia,and intraoperative exploration confirmed that the greater omentum tumor protruded into the scrotum.Therefore,tumor resection and tension-free inguinal hernia repair were performed.The final diagnosis was benign fibroma of the greater omentum accompanied by an indirect inguinal hernia.CONCLUSION This unusual presentation of a common inguinal hernia disease illustrates the necessity of performing detailed history taking,physical examination,and imaging before surgery.

Phenolic Profile and Volatiles of in vitro Propagated Lavandula angustifolia Mill.Seedlings

An effective in vitro propagation protocol was designed for Lavandula angustifolia Miller,a medicinal aromatic plant that is a prominent source of volatile organic compounds(VOCs).Murashige and Skoog media were supplemented with various concentrations of Plant Growth Regulators(PGRs),and the growth parameters of the nodal segments were examined.Nodal explants formed callus when they were supplemented with 2 mg/L of 6-Benzylaminopurine(BAP).The superior hormonal concentration of Murashige and Skoog(MS)media for the proliferation of shoots from callus cultures(39.33%)was 5 mg/L of 2-Isopentenyl adenine(2iP),and the favorable media for the growth of L.angustifolia callus cultures was 1 and 2 mg/L of BAP,with a 98%for-mation rate in each case.The callus cultures and in vitro propagated L.angustifolia seedlings obtained from var-ious PGR concentrations of MS media were exposed to qualitative and quantitative analysis in terms of phenolic profiles,flavonoids,High-performance liquid chromatography(HPLC)analysis of phenolic acids,and headspace-SPME analysis for volatiles.Such analysis revealed that micropropagated seedlings grown in media containing 1 mg/L of 6-Furfurylaminopurine(KIN)accumulated the highest yield(11.95±0.01 mg GAE/g)of phenolic acids.In contrast,the lowest concentration(2.17±0.04 mg GAE/g)was detected in 0.5 mg/L of BAP+0.5 mg/L of Naphthaleneacetic acid(NAA)media.The plantlets grown in 0.5 mg/L of BAP+0.5 mg/L of NAA media showed the highestflavonoid yield(31.67±0.06μg/g QE/g).In contrast,callus samples exhibited the lowest yield(11.59±0.02μg/g QE/g)offlavonoids in MS media supplemented with a concentration of 0.5 mg/L of BAP.HPLC analysis revealed the variability of phenolic acid contents within the callus cultures as well as plantlets,with gallic acid,4-OH benzoic acid,chlorogenic acid,vanillic acid,caffeic acid,cinnamic acid,and rosmarinic acid being the prominent constituents.The presence of twenty-two chemicals was revealed by headspace-SPME analysis.Eucalyptol,nonanal,borneol,carvone,andβ-caryophyllene were the most abundant.This study demonstrated that micropropagation of L.angustifolia may be an effective method to produce large numbers of genetically identical plantlets for the production of high-value bio compounds.

Shear wave velocity prediction:A review of recent progress and future opportunities

Shear logs,also known as shear velocity logs,are used for various types of seismic analysis,such as determining the relationship between amplitude variation with offset(AVO)and interpreting multiple types of seismic data.This log is an important tool for analyzing the properties of rocks and interpreting seismic data to identify potential areas of oil and gas reserves.However,these logs are often not collected due to cost constraints or poor borehole conditions possibly leading to poor data quality,though there are various approaches in practice for estimating shear wave velocity.In this study,a detailed review of the recent advances in the various techniques used to measure shear wave(S-wave)velocity is carried out.These techniques include direct and indirect measurement,determination of empirical relationships between S-wave velocity and other parameters,machine learning,and rock physics models.Therefore,this study creates a collection of employed techniques,enhancing the existing knowledge of this significant topic and offering a progressive approach for practical implementation in the field.

Factors that influence the results of indirect decompression employing oblique lumbar interbody fusion

BACKGROUND Indirect decompression is one of the potential benefits of anterior reconstruction in patients with spinal stenosis.On the other hand,the reported rate of revision surgery after indirect decompression highlights the necessity of working out prediction models for the radiographic results of indirect decompression with assessing their clinical relevance.AIM To assess factors that influence radiographic and clinical results of the indirect decompression in patients with stenosis of the lumbar spine.METHODS This study is a single-center cross-sectional evaluation of 80 consecutive patients(17 males and 63 females)with lumbar spinal stenosis combined with the instability of the lumbar spinal segment.Patients underwent single level or bisegmental spinal instrumentation employing oblique lumbar interbody fusion(OLIF)with percutaneous pedicle screw fixation.Radiographic results of the indirect decompression were assessed using computerized tomography,while MacNab scale was used to assess clinical results.RESULTS After indirect decompression employing anterior reconstruction using OLIF,the statistically significant increase in the disc space height,vertebral canal square,right and left lateral canal depth were detected(Р<0.0001).The median(M)relative vertebral canal square increase came toМ=24.5%with 25%-75%quartile border(16.3%;33.3%)if indirect decompression was achieved by restoration of the segment height.In patients with the reduction of the upper vertebrae slip,the median of the relative increase in vertebral canal square accounted for 49.5%with 25%-75%quartile border(2.35;99.75).Six out of 80 patients(7.5%)presented with unsatisfactory results because of residual nerve root compression.The critical values for lateral recess depth and vertebral canal square that were associated with indirect decompression failure were 3 mm and 80 mm2 respectively.CONCLUSION Indirect decompression employing anterior reconstruction is achieved by the increase in disc height along the posterior boarder and reduction of the slipped vertebrae in patients with degenerative spondylolisthesis.Vertebral canal square below 80 mm2 and lateral recess depth less than 3 mm are associated with indirect decompression failures that require direct microsurgical decompression.

Prevalence and Factors Associated with Positivity of Antinuclear Antibodies (ANA) Patterns, Native Anti-DNA and Extractable Nuclear Antigens (ENA) Antibodies: Experience from a Laboratory in Dakar

Background: Diagnosis of autoimmune diseases (AID) is challenging, due to overlapping features with other non-immune disorders. Anti-nuclear antibodies (ANA) are sensitive screening tests but anti-deoxyribonucleic acid-antibody (anti-DNA), and anti-extractable nuclear antigens (anti-ENA) are specific for AIDs. We aimed to look at ANA patterns in our patients and correlated them with anti-ENA for proper interpretation and better patient management cost-effectively. Methods: A retrospective study was conducted over 1 year from January to December 2022 who were tested for ANA at biology medical laboratory of Pasteur Institute of Dakar. Anti-ENA and anti-DNA results were also analyzed for ANA-positive patients. Statistical analysis was performed using STATA 14.0, p Results: 216 patients were analyzed. Women predominated at 79.2% and mean age was 48 years [CI 95%, 46 - 50], with extremes of 10 and 89. Most represented age group was [41 - 60] with 38%. ANA was positive in 27 (12.5%) of patients, 59.2% of whom were strongly positive (titer of 1/1000, 1/3200 or 1/6400). The most common pattern was nuclear speckled, which was found in 77.8% of samples. Anti-ENA and anti-DNA positivity in ANA-positive patients was found respectively in 63% (17/27) and 1.4% (3/27) of the samples analyzed. Most commonly identified anti-ENA was anti-Sm 29.6%, anti-SSA 29.6%, anti-Ro-52 25.9%, anti-RNP 18.5% and anti-SSB 14.8% which was associated with speckled pattern. Association results indicated a significant relationship between both tests and between ANA titer in the anti-ENA- and ANA-positive patients (p 0.001). Conclusions: ANA, Anti-ENA and anti-DNA antibodies are essential for AIDS diagnosis. However, the testing repertoire should follow an algorithm comprising of clinical features, followed by ANA results with nuclear, mitotic, and cytoplasmic patterns, anti-ENA, and anti-DNA for a more meaningful, and cost-effective diagnostic approach.

Analysis of Standards and Effects of Police Indirect Court of Human Rights——Taking“Akbay and Others v.Germany”as an Example

The European Court of Human Rights(ECtHR)has ruled that illegal indirect entrapment must meet three criteria simultaneously.This mixed standard requires that the previous direct entrapment violates the“essentially passive,”subsequent indirect entrapment satisfies the“reasonable foreseeability,”and police entrapment of secondary defendants to commit crimes is considered“decisive.”The legal consequences of indirect entrapment are distinguished between general indirect entrapment and illegal indirect entrapment.The basic position of the ECtHR on the consequences of illegal indirect entrapment has shifted from supporting mitigating penalties to recognizing procedural dismissal,and general indirect entrapment is considered a mitigating factor in sentencing.Against the backdrop of increasing internationalization of criminal justice standards,the above criteria and positions have strong implications for the improvement of relevant rules in China.

Experimental Study and Thermal Modelling of Cocoa Shell Convective Drying in an Indirect Solar Dryer

The concern of the present work is the convective drying of empty cocoa shells in an indirect solar dryer. Some drying experiments, using one sample, were carried out. During the experiments, the sample is introduced in the drying chamber. Then at steady time intervals, the sample is withdrawn from the drying chamber, for a rapid weighing. After each weighing, the sample is reintroduced in the dryer. At each time interval, the ambient temperature of the drying chamber and its relative humidity γ are measured by a thermo-hygrometer. From the experimental data, a theoretical determination of the moisture evaporated from the product was performed and a good agreement was found between the theoretical and experimental values, confirmed by the value of the RMSE. Those calculations used the constants in the Nusselt number found in literature. Then those constants were evaluated again, to get new values more suitable with the experimental data. The dimensionless numbers of Nusselt, Grashof and Prandtl were calculated. That allowed the calculation of the average value of the Nusselt number. The average convective heat transfer coefficient was determined.

Indirect Electroanalysis of 3-Methyl-4-Nitrophenol in Water Using Carbon Fiber Microelectrode Modified with Nickel Tetrasulfonated Phthalocyanine Complex

Electrochemical detection of 3-methyl-4-nitrophenol (MNP) in direct phenol oxidation occurs at high potentials and generally leads to progressive passivation of the electrochemical sensor. This study describes the use of a carbon fiber microelectrode modified with a tetrasulfonated nickel phthalocyanine complex for the detection of MNP at a lower potential than that of direct phenol oxidation. The MNP voltammogram showed the presence of an anodic peak at -0.11 V vs SCE, corresponding to the oxidation of the hydroxylamine group generated after the reduction of the nitro group. The effect of buffer pH on the peak current and SWV parameters such as frequency, scan increment, and pulse amplitude were studied and optimized to have better electrochemical response of the proposed sensor. With these optimal parameters, the calibration curve shows that the peak current varied linearly as a function of MNP concentration, leading to a limit of detection (LoD) of 1.1 μg/L. These results show an appreciable sensitivity of the sensor for detecting the MNP at relatively low potentials, making it possible to avoid passivation phenomena.

Switching of K-Q intervalley trions fine structure and their dynamics in n-doped monolayer WS_(2)

Monolayer group VI transition metal dichalcogenides(TMDs)have recently emerged as promising candidates for photonic and opto-valleytronic applications.The optoelectronic properties of these atomically-thin semiconducting crystals are strongly governed by the tightly bound electron-hole pairs such as excitons and trions(charged excitons).The anomalous spin and valley configurations at the conduction band edges in monolayer WS_(2)give rise to even more fascinating valley many-body complexes.Here we find that the indirect Q valley in the first Brillouin zone of monolayer WS_(2)plays a critical role in the formation of a new excitonic state,which has not been well studied.By employing a high-quality h-BN encapsulated WS_(2)field-effect transistor,we are able to switch the electron concentration within K-Q valleys at conduction band edges.Consequently,a distinct emission feature could be excited at the high electron doping region.Such feature has a competing population with the K valley trion,and experiences nonlinear power-law response and lifetime dynamics under doping.Our findings open up a new avenue for the study of valley many-body physics and quantum optics in semiconducting 2D materials,as well as provide a promising way of valley manipulation for next-generation entangled photonic devices.

Compression behavior of 316L lattice structures produced by indirect additive manufacturing

As a new type of lightweight structure,metallic lattice structure has higher stiffness and strength to weight ratio.To freely obtain 316L lattice structures with designed cell structure and adjustable porosity,additive manufacturing combined with investment casting was conducted to fabricate the 316L lattice structures with Kelvin cell.The compression simulation of 316L lattice structures with different porosities was carried out by using the finite element method.The numerical simulation results were verified by compression experiment,and the simulated results were consistent with the compression tests.The compressive mechanical properties of 316L lattice structures are directly related to porosity and independent of strut diameters.The 316L lattice structures with Kelvin cell have a smooth stress-strain curve and obvious plastic platform,and the hump stress-strain curves are avoided.

Indirect Vector Control of Linear Induction Motors Using Space Vector Pulse Width Modulation

Vector control schemes have recently been used to drive linear induction motors(LIM)in high-performance applications.This trend promotes the development of precise and efficient control schemes for individual motors.This research aims to present a novel framework for speed and thrust force control of LIM using space vector pulse width modulation(SVPWM)inverters.The framework under consideration is developed in four stages.To begin,MATLAB Simulink was used to develop a detailed mathematical and electromechanical dynamicmodel.The research presents a modified SVPWM inverter control scheme.By tuning the proportional-integral(PI)controller with a transfer function,optimized values for the PI controller are derived.All the subsystems mentioned above are integrated to create a robust simulation of the LIM’s precise speed and thrust force control scheme.The reference speed values were chosen to evaluate the performance of the respective system,and the developed system’s response was verified using various data sets.For the low-speed range,a reference value of 10m/s is used,while a reference value of 100 m/s is used for the high-speed range.The speed output response indicates that themotor reached reference speed in amatter of seconds,as the delay time is between 8 and 10 s.The maximum amplitude of thrust achieved is less than 400N,demonstrating the controller’s capability to control a high-speed LIM with minimal thrust ripple.Due to the controlled speed range,the developed system is highly recommended for low-speed and high-speed and heavy-duty traction applications.