Based on the numerical simulation analysis, structure parameters of the high pressure fuel pump and common rail as well as flow limiter are designed and the GD-1 high pressure common rail fuel injection system is self...Based on the numerical simulation analysis, structure parameters of the high pressure fuel pump and common rail as well as flow limiter are designed and the GD-1 high pressure common rail fuel injection system is self-developed. Fuel injection characteristics experiment is performed on the GD-1 system. And double-factor variance analysis is applied to investigate the influence of the rail pressure and injection pulse width on the consistency of fuel injection quantity, thus to test whether the design of structure parameters is sound accordingly. The results of experiment and test show that rail pressure and injection pulse width as well as their mutual-effect have no influence on the injection quantity consistency, which proves that the structure parameters design is successful and performance of GD-1 system is sound.展开更多
Lead has been recognized as a high risk toxic for most organisms including human. The effects of Pb in non-mammalian vertebrates are oprly known, particularly in anuran amphibians. The purpose of this study was to det...Lead has been recognized as a high risk toxic for most organisms including human. The effects of Pb in non-mammalian vertebrates are oprly known, particularly in anuran amphibians. The purpose of this study was to determine the effect of this metal on some hematological parameters of adult Bufo arenarum. It was found that all parameters remained unaltered within normal ranges, with the exception of reticulocyte counts which was significantly increased compared to the in controls (3. 7% vs. 0. 2 % ). It is suggested that the selective change found in reticulocyte count might be considered as an early response of a biomarker to sublethal exposition of Bufo arenarum to lead.展开更多
The China Spallation Neutron Source (CSNS) uses H- stripping and phase space painting metnocl co fill a large ring acceptance with a small emittance linac beam. The dependence of the painting beam on the injection b...The China Spallation Neutron Source (CSNS) uses H- stripping and phase space painting metnocl co fill a large ring acceptance with a small emittance linac beam. The dependence of the painting beam on the injection beam parameters was studied for the Rapid Cycling Synchrotron (RCS). The simulation study was done for injection with different momentum spreads, different rms emittances of the injection beam, and different matching conditions. Then, the beam loss, 99% and rms emittances were obtained, and the optimized injection beam parameters were given. The interaction between H- beam and stripping foil was studied, and the effect of foil scattering was simulated. The stripping efficiency was calculated and the suitable thickness of stripping foil was obtained. In addition, the energy deposition on the foil and the beam loss due to the foil scattering were also studied.展开更多
We propose a novel method to compute globally injective parameterizations with arbitrary positional constraints on disk topology meshes.Central to this method is the use of a scaffold mesh that reduces the globally in...We propose a novel method to compute globally injective parameterizations with arbitrary positional constraints on disk topology meshes.Central to this method is the use of a scaffold mesh that reduces the globally injective constraint to a locally flipfree condition.Hence,given an initial parameterized mesh containing flipped triangles and satisfying the positional constraints,we only need to remove the flips of a overall mesh consisting of the parameterized mesh and the scaffold mesh while always meeting positional constraints.To successfully apply this idea,we develop two key techniques.Firstly,an initialization method is used to generate a valid scaffold mesh and mitigate difficulties in eliminating flips.Secondly,edgebased remeshing is used to optimize the regularity of the scaffold mesh containing flips,thereby improving practical robustness.Compared to state-of-the-art methods,our method is much more robust.We demonstrate the capability and feasibility of our method on a large number of complex meshes.展开更多
In this paper effects of various injection molding parameters on tribological properties of ultra-high molecular weight polyethylene (UHMWPE) were investigated. The tribological properties like coefficient of fricti...In this paper effects of various injection molding parameters on tribological properties of ultra-high molecular weight polyethylene (UHMWPE) were investigated. The tribological properties like coefficient of friction and wear rate were obtained from the experimental results of hip simulator which was designed and fabricated in the laboratory. Bovine serum was used as a lubricant in this study. In addition, the hardness of the specimen was also investigated as well. The injection molding parameters that varied for this study are melt temperature, injection velocity and compaction time. The results show that contact loads and melt temperature were mostly influenced the tribological behavior of UHMWPE. A wear mechanism map was developed to study the dominant wear mechanism that influences the wear behavior of UHMWPE. SEM was employed to study the worn out morphologies of UHMWPE. The dominant wear mechanisms that are dominated through our study are ironing, scratching, ploughing, plastic deformation, and fatigue wear.展开更多
文摘Based on the numerical simulation analysis, structure parameters of the high pressure fuel pump and common rail as well as flow limiter are designed and the GD-1 high pressure common rail fuel injection system is self-developed. Fuel injection characteristics experiment is performed on the GD-1 system. And double-factor variance analysis is applied to investigate the influence of the rail pressure and injection pulse width on the consistency of fuel injection quantity, thus to test whether the design of structure parameters is sound accordingly. The results of experiment and test show that rail pressure and injection pulse width as well as their mutual-effect have no influence on the injection quantity consistency, which proves that the structure parameters design is successful and performance of GD-1 system is sound.
文摘Lead has been recognized as a high risk toxic for most organisms including human. The effects of Pb in non-mammalian vertebrates are oprly known, particularly in anuran amphibians. The purpose of this study was to determine the effect of this metal on some hematological parameters of adult Bufo arenarum. It was found that all parameters remained unaltered within normal ranges, with the exception of reticulocyte counts which was significantly increased compared to the in controls (3. 7% vs. 0. 2 % ). It is suggested that the selective change found in reticulocyte count might be considered as an early response of a biomarker to sublethal exposition of Bufo arenarum to lead.
基金Supported by National Natural Science Foundation of China(11205185,11175020,11175193)
文摘The China Spallation Neutron Source (CSNS) uses H- stripping and phase space painting metnocl co fill a large ring acceptance with a small emittance linac beam. The dependence of the painting beam on the injection beam parameters was studied for the Rapid Cycling Synchrotron (RCS). The simulation study was done for injection with different momentum spreads, different rms emittances of the injection beam, and different matching conditions. Then, the beam loss, 99% and rms emittances were obtained, and the optimized injection beam parameters were given. The interaction between H- beam and stripping foil was studied, and the effect of foil scattering was simulated. The stripping efficiency was calculated and the suitable thickness of stripping foil was obtained. In addition, the energy deposition on the foil and the beam loss due to the foil scattering were also studied.
基金supported by the National Natural Science Foundation of China(61802359,62025207)USTC Research Funds of the Double First-Class Initiative(YD0010002003).
文摘We propose a novel method to compute globally injective parameterizations with arbitrary positional constraints on disk topology meshes.Central to this method is the use of a scaffold mesh that reduces the globally injective constraint to a locally flipfree condition.Hence,given an initial parameterized mesh containing flipped triangles and satisfying the positional constraints,we only need to remove the flips of a overall mesh consisting of the parameterized mesh and the scaffold mesh while always meeting positional constraints.To successfully apply this idea,we develop two key techniques.Firstly,an initialization method is used to generate a valid scaffold mesh and mitigate difficulties in eliminating flips.Secondly,edgebased remeshing is used to optimize the regularity of the scaffold mesh containing flips,thereby improving practical robustness.Compared to state-of-the-art methods,our method is much more robust.We demonstrate the capability and feasibility of our method on a large number of complex meshes.
文摘In this paper effects of various injection molding parameters on tribological properties of ultra-high molecular weight polyethylene (UHMWPE) were investigated. The tribological properties like coefficient of friction and wear rate were obtained from the experimental results of hip simulator which was designed and fabricated in the laboratory. Bovine serum was used as a lubricant in this study. In addition, the hardness of the specimen was also investigated as well. The injection molding parameters that varied for this study are melt temperature, injection velocity and compaction time. The results show that contact loads and melt temperature were mostly influenced the tribological behavior of UHMWPE. A wear mechanism map was developed to study the dominant wear mechanism that influences the wear behavior of UHMWPE. SEM was employed to study the worn out morphologies of UHMWPE. The dominant wear mechanisms that are dominated through our study are ironing, scratching, ploughing, plastic deformation, and fatigue wear.