Emerging MoS_(2)Wafer-Scale Technique for Integrated Circuits

As an outstanding representative of layered materials,molybdenum disulfide(MoS_(2))has excellent physical properties,such as high carrier mobility,stability,and abundance on earth.Moreover,its reasonable band gap and microelectronic compatible fabrication characteristics makes it the most promising candidate in future advanced integrated circuits such as logical electronics,flexible electronics,and focal-plane photodetector.However,to realize the all-aspects application of MoS_(2),the research on obtaining high-quality and large-area films need to be continuously explored to promote its industrialization.Although the MoS_(2)grain size has already improved from several micrometers to sub-millimeters,the high-quality growth of wafer-scale MoS_(2)is still of great challenge.Herein,this review mainly focuses on the evolution of MoS_(2)by including chemical vapor deposition,metal–organic chemical vapor deposition,physical vapor deposition,and thermal conversion technology methods.The state-of-the-art research on the growth and optimization mechanism,including nucleation,orientation,grain,and defect engineering,is systematically summarized.Then,this review summarizes the wafer-scale application of MoS_(2)in a transistor,inverter,electronics,and photodetectors.Finally,the current challenges and future perspectives are outlined for the wafer-scale growth and application of MoS_(2).

Through-silicon-via crosstalk model and optimization design for three-dimensional integrated circuits

Through-silicon-via （TSV） to TSV crosstalk noise is one of the key factors affecting the signal integrity of three- dimensional integrated circuits （3D ICs）. Based on the frequency dependent equivalent electrical parameters for the TSV channel, an analytical crosstalk noise model is established to capture the TSV induced crosstalk noise. The impact of various design parameters including insulation dielectric, via pitch, via height, silicon conductivity, and terminal impedance on the crosstalk noise is analyzed with the proposed model. Two approaches are proposed to alleviate the TSV noise, namely, driver sizing and via shielding, and the SPICE results show 241 rnV and 379 mV reductions in the peak noise voltage, respectively.

High density Al2O3/TaN-based metal-insulatormetal capacitors in application to radio equency integrated circuits

Metal-insulator-metal （MIM） capacitors with atomic-layer-deposited Al2O3 dielectric and reactively sputtered TaN electrodes in application to radio frequency integrated circuits have been characterized electrically. The capacitors exhibit a high density of about 6.05 fF/μm^2, a small leakage current of 4.8 × 10^-8 A/cm^2 at 3 V, a high breakdown electric field of 8.61 MV/cm as well as acceptable voltage coefficients of capacitance （VCCs） of 795 ppm/V2 and 268ppm/V at 1 MHz. The observed properties should be attributed to high-quality Al2O3 film and chemically stable TaN electrodes. Further, a logarithmically linear relationship between quadratic VCC and frequency is observed due to the change of relaxation time with carrier mobility in the dielectric. The conduction mechanism in the high field ranges is dominated by the Poole-Frenkel emission, and the leakage current in the low field ranges is likely to be associated with trap-assisted tunnelling. Meanwhile, the Al2O3 dielectric presents charge trapping under low voltage stresses, and defect generation under high voltage stresses, and it has a hard-breakdown performance.

Human blood plasma-based electronic integrated circuit amplifier configuration

Dear Editor： There is accumulating evidence that human blood electronic circuit components and their application circuits become more and more important to cyborg implant/engineering, man-machine interface, hu- man disease detection and healing, and artificial brain evolutionusl. Here, we report the first development of human plasma-based amplifier circuit in the dis- crete as well as integrated circuit （IC） configuration mode. Electrolytes in the human blood contain an enormous number of charge carriers such as positive and negative molecule/atom ions, which are electri- cally conducting media and therefore can be utilized for developing electronic circuit components and their application circuits. These electronic circuits obvi- ously have very high application impact potential towards bio-medical engineering and medical science and technology.

A 330-500 GHz Zero-Biased Broadband Tripler Based on Terahertz Monolithic Integrated Circuits

A 330-500 GHz zero-biased broadband monolithic integrated tripler is reported. The measured results show that the maximum efficiency and the maximum output power are 2% and 194μW at 348 GHz. The saturation characteristic test shows that the output i dB compression point is about -8.5 dBm at 334 GHz and the maximum efficiency is obtained at the point, which is slightly below the 1 dB compression point. Compared with the conventional hybrid integrated circuit, a major advantage of the monolithic integrated circuit is the significant improvement of reliability and consistency. In this work, a terahertz monolithic frequency multiplier at this band is designed and fabricated.

Concise Modeling of Amorphous Dual-Gate In-Ga-Zn-O Thin-Film Transistors for Integrated Circuit Designs

An analytical model for current-voltage behavior of amorphous In-Ga-Zn-O thin-film transistors（a-IGZO TFTs）with dual-gate structures is developed.The unified expressions for synchronous and asynchronous operating modes are derived on the basis of channel charges,which are controlled by gate voltage.It is proven that the threshold voltage of asynchronous dual-gate IGZO TFTs is adjusted in proportion to the ratio of top insulating capacitance to the bottom insulating capacitance（C_（TI）/C_（BI））.Incorporating the proposed model with Verilog-A,a touch-sensing circuit using dual-gate structure is investigated by SPICE simulations.Comparison shows that the touch sensitivity is increased by the dual-gate IGZO TFT structure.

Influence of Tilted Angle on Effective Linear Energy Transfer in Single Event Effect Tests for Integrated Circuits at 130 nm Technology Node

A heavy-ion irradiation experiment is studied in digital storage cells with different design approaches in 130？nm CMOS bulk Si and silicon-on-insulator （SOI） technologies. The effectiveness of linear energy transfer （LET） with a tilted ion beam at the 130？nm technology node is obtained. Tests of tilted angles θ=0 ° , 30 ° and 60 ° with respect to the normal direction are performed under heavy-ion Kr with certain power whose LET is about 40？MeVcm 2 /mg at normal incidence. Error numbers in D flip-flop chains are used to determine their upset sensitivity at different incidence angles. It is indicated that the effective LETs for SOI and bulk Si are not exactly in inverse proportion to cosθ , furthermore the effective LET for SOI is more closely in inverse proportion to cosθ compared to bulk Si, which are also the well known behavior. It is interesting that, if we design the sample in the dual interlocked storage cell approach, the effective LET in bulk Si will look like inversely proportional to cosθ very well, which is also specifically explained.

Hybrid material integration in silicon photonic integrated circuits

Hybrid integration ofⅢ-Ⅴand ferroelectric materials is being broadly adopted to enhance functionalities in silicon photonic integrated circuits(PICs).Bonding and transfer printing have been the popular approaches for integration of III–V gain media with silicon PICs.Similar approaches are also being considered for ferroelectrics to enable larger RF modulation bandwidths,higher linearity,lower optical loss integrated optical modulators on chip.In this paper,we review existing integration strategies ofⅢ-Ⅴmaterials and present a route towards hybrid integration of bothⅢ-Ⅴand ferroelectrics on the same chip.We show that adiabatic transformation of the optical mode between hybrid ferroelectric and silicon sections enables efficient transfer of optical modal energies for maximum overlap of the optical mode with the ferroelectric media,similar to approaches adopted to maximize optical overlap with the gain section,thereby reducing lasing thresholds for hybridⅢ-Ⅴintegration with silicon PICs.Preliminary designs are presented to enable a foundry compatible hybrid integration route of diverse functionalities on silicon PICs.

Digital synthesis of programmable photonic integrated circuits

Programmable photonic waveguide meshes can be programmed into many different circuit topologies and thereby provide a variety of functions.Due to the complexity of the signal routing in a general mesh,a particular synthesis algorithm often only accounts for a specific function with a specific cell configuration.In this paper,we try to synthesize the programmable waveguide mesh to support multiple configurations with a more general digital signal processing platform.To show the feasibility of this technique,photonic waveguide meshes in different configurations(square,triangular and hexagonal meshes)are designed to realize optical signal interleaving with arbitrary duty cycles.The digital signal processing(DSP)approach offers an effective pathway for the establishment of a general design platform for the software-defined programmable photonic integrated circuits.The use of well-developed DSP techniques and algorithms establishes a link between optical and electrical signals and makes it convenient to realize the computer-aided design of optics–electronics hybrid systems.

Device Physics Research for Submicron and Deep Submicron Space Microelectronics Devices and Integrated Circuits

Device physics research for submicron and deep submicron space microelectronics devices and integrated circuits will be described in three topics.1.Thin film submicron and deep submicron SOS / CMOS devices and integrated circuits.2.Deep submicron LDD CMOS devices and integrated circuits.3.C band and Ku band microwave GaAs MESFET and III-V compound hetrojunction HEM T and HBT devices and integrated circuits.

Development of 0.50μm CMOS Integrated Circuits Technology

Submicron CMOS IC technology, including triple layer resist lithography technology, RIE, LDD, Titanium Salicide, shallow junction, thin gate oxide, no bird's beak isolation and channel's multiple implantation doping technology have been developed. 0.50μm. CMOS integrated circuits have been fabricated using this submicron CMOS process.

Development of Physical Library for Short Channel CMOS / SOI Integrated Circuits

An 'Integrated Device and Circuit simulator' for thin film (0.05-0.2μm) submicron (0.5μm) and deep submicron (0.15, 0.25,0.35μm) CMOS/ SOI integrated circuit has been developed. This simulator has been used for design and fabrication and physical library development of thin film submicron and deep submicron CMOS/ SOI integrated circuit.

Microwave Integrated Circuit Design Handbook

作者:Reinmut K.Hoffmann(1984 IEEE微波奖获得者) 出版:Artech House公司(美国)1987年本书给出适于微波工程师和研究人员应用的有关MIC方面的基础技术、电性能和设计。侧重于电性能分析和设计,强调应用。对于每一种设计技术和应用均作出较清楚的叙述和完整的处理。本书尽量给出电路的物理描述,避免过于冗长的数学公式,内容包含对下列议题的详细评述与研讨:

ESD Protection Design and Characteristic Analysis of Advanced Process Integrated Circuit

The electrostatic discharge(ESD)phenomenon is very common,in daily life,many places will appear ESD phenomenon.However,ESD is a potential hazard for integrated circuits.This paper analyzes the ESD protection design and characteristics of advanced process integrated circuits,and puts forward personal views combined with experience,hoping to bring help to the people who pay attention to the ESD protection of integrated circuits.

Advances in Developing Transitions in Microwave Integrated Circuits

Advances in developing transitions in microwave integrated circuits during the last ten years are reviewed. Some typical structures of transition are introduced. Transition structures can be classified into two basic types: one is transition between the same kind of transmission lines on different planes of a common substrate, the other transition between different types of transmission lines. Furthermore, future development of transition structures is discussed.

Gigahertz-rate-switchable wavefront shaping through integration of metasurfaces with photonic integrated circuit

Achieving spatiotemporal control of light at high speeds presents immense possibilities for various applications in communication,computation,metrology,and sensing.The integration of subwavelength metasurfaces and optical waveguides offers a promising approach to manipulate light across multiple degrees of freedom at high speed in compact photonic integrated circuit(PIC)devices.Here,we demonstrate a gigahertz-rate-switchable wavefront shaping by integrating metasurface,lithium niobate on insulator photonic waveguides,and electrodes within a PIC device.As proofs of concept,we showcase the generation of a focus beam with reconfigurable arbitrary polarizations,switchable focusing with lateral focal positions and focal length,orbital angular momentum light beams as well as Bessel beams.Our measurements indicate modulation speeds of up to the gigahertz rate.This integrated platform offers a versatile and efficient means of controlling the light field at high speed within a compact system,paving the way for potential applications in optical communication,computation,sensing,and imaging.

Predicting stability of integrated circuit test equipment using upper side boundary values of normal distribution

In response to the growing complexity and performance of integrated circuit(IC),there is an urgent need to enhance the testing and stability of IC test equipment.A method was proposed to predict equipment stability using the upper side boundary value of normal distribution.Initially,the K-means clustering algorithm classifies and analyzes sample data.The accuracy of this boundary value is compared under two common confidence levels to select the optimal threshold.A range is then defined to categorize unqualified test data.Through experimental verification,the method achieves the purpose of measuring the stability of qualitative IC equipment through a deterministic threshold value and judging the stability of the equipment by comparing the number of unqualified data with the threshold value,which realizes the goal of long-term operation monitoring and stability analysis of IC test equipment.

Constructing a Specialized Computer Integrated Circuit Reliability Experiment Platform

Against the backdrop of the strategy to build a manufacturing powerhouse and the rapid development of integrated circuits(ICs),the emergence of new technologies,materials,and processes has rendered traditional IC reliability techniques inadequate for the evolving needs of IC development.Addressing the construction of an innovative IC reliability experiment platform has become a critical issue for scientific researchers at our city’s universities.This paper takes the Shenyang branch of the National Special Computer Research Center as a case study to explore how to optimize the construction of an IC reliability innovation platform.The discussion is structured around three dimensions:expanding the platform’s application scope,enhancing talent capabilities,and improving technological innovation levels.The findings are instrumental in elevating the standard of innovation platforms within the city.

Two-dimensional materials in photonic integrated circuits:recent developments and future perspectives[Invited]

The heterogeneous integration of photonic integrated circuits(PICs)with a diverse range of optoelectronic materials has emerged as a transformative approach,propelling photonic chips toward larger scales,superior performance,and advanced integration levels.Notably,two-dimensional(2D)materials,such as graphene,transition metal dichalcogenides(TMDCs),black phosphorus(BP),and hexagonal boron nitride(hBN),exhibit remarkable device performance and integration capabilities,offering promising potential for large-scale implementation in PICs.In this paper,we first present a comprehensive review of recent progress,systematically categorizing the integration of photonic circuits with 2D materials based on their types while also emphasizing their unique advantages.Then,we discuss the integration approaches of 2D materials with PICs.We also summarize the technical challenges in the heterogeneous integration of 2D materials in photonics and envision their immense potential for future applications in PICs.

Wide bandgap semiconductor-based integrated circuits

Wide-bandgap semiconductors exhibit much larger energybandgaps than traditional semiconductors such as silicon,rendering them very promising to be applied in the fields of electronics and optoelectronics.Prominent examples of semiconductors include SiC,GaN,ZnO,and diamond,which exhibitdistinctive characteristics such as elevated mobility and thermalconductivity.These characteristics facilitate the operation of awide range of devices,including energy-efficient bipolar junctiontransistors(BJTs)and metal-oxide-semiconductor field-effecttransistors(MOSFETs),as well as high-frequency high-electronmobility transistors(HEMTs)and optoelectronic components suchas light-emitting diodes(LEDs)and lasers.These semiconductorsare used in building integrated circuits(ICs)to facilitate theoperation of power electronics,computer devices,RF systems,andother optoelectronic advancements.These breakthroughs includevarious applications such as imaging,optical communication,andsensing.Among them,the field of power electronics has witnessedtremendous progress in recent years with the development of widebandgap(WBG)semiconductor devices,which is capable ofswitching large currents and voltages rapidly with low losses.However,it has been proven challenging to integrate these deviceswith silicon complementary metal oxide semiconductor(CMOS)logic circuits required for complex control functions.The monolithic integration of silicon CMOS with WBG devices increases thecomplexity of fabricating monolithically integrated smart integrated circuits(ICs).This review article proposes implementingCMOS logic directly on the WBG platform as a solution.However,achieving the CMOS functionalities with the adoption of WBGmaterials still remains a significant hurdle.This article summarizesthe research progress in the fabrication of integrated circuitsadopting various WBG materials ranging from SiC to diamond,with the goal of building future smart power ICs.