Imaging plate scanners calibration and the attenuation behavior of imaging plate signals

Based on previously reported work, we propose a new method for calibrating image plate(IP) scanners, offering greater flexibility and convenience, which can be extended to the calibration tasks of various scanner models. This method was applied to calibrate the sensitivity of a GE Typhoon FLA 7000 scanner. Additionally, we performed a calibration of the spontaneous signal attenuation behavior for BAS-MS, BAS-SR, and BAS-TR type IPs under the 20±1℃ environmental conditions, and observed significant signal carrier diffusion behavior in BAS-MS IP. The calibration results lay a foundation for further research on the interaction between ultra-short, ultra-intense lasers and matter.

Influence of layout of scanners on intelligent mine scanning trails

To expand scanning area and attack range without changing the inner structure of intelligent warhead, a new arrangement mode of the scanner for intelligent mine is proposed. The required coordinate systems are established firstly on the basis of advanced dynamics principle. and the exterior ballistics equations are deduced. Then the equations of scanning trails are established by the method of space analytic geometry. To get the scanning trails. the differential equations are transformed into discrete simulation model using the algorithm of fourth order Runge-Kutta and then are simulated using Matlab. Compared with the scanning trails obtained by the traditional layout of scanner, the scanning trails obtained by the proposed layout of scanner has larger horizontal range of scanning circle and bigger trarget acquisition probability. Therefore, the new arrangement mode of the scanner for intelligent mine can increase attack range.

Evaluation of the Accuracy of Digital Models Obtained Using Intraoral and Extraoral Scanners versus Gold Standard Plaster Model (Diagnostic Accuracy Study)

Introduction: Digital models showed promising results for orthodontic diagnosis and treatment planning. Digital models can be obtained from alginate impressions as well as direct intra-oral scanners. Studies assessing the accuracy of digital models have shown digital models to be valid, clinically acceptable, and more quickly obtainable. With the advent of new scanners with better scanning technology researches are necessary to evaluate their accuracy and reliability. Aim of Study: To evaluate the diagnostic accuracy of 3D digital models obtained through intraoral and extraoral scanning modalities to the reference gold standard plaster model. Material & Methods: Twenty-four adult male and female subjects were randomly selected for this study. The intraoral scanners evaluated in this study were Sirona (CEREC Omnicam) and 3 shape (TRIOS 3), while the laboratory scanners used were Sirona (inEos X5), and 3 shape (D850). Intra-oral scanning of the subjects and extra-oral scanning of their alginate impressions, plaster models of the alginate impression, rubber base impression, and plaster model of their rubber base impression were done. Linear dental measurements included intermolar width, interpremolar width, intercanine width, mesiodistal width of the 1st permanent molar, 1st premolar, canine and central incisor and arch width. All data were collected, tabulated and subjected to statistical analysis. Results: Small differences between the plaster and digital models were observed. Intra-observer reliability analysis for 14 out of the 16 measurements showed that all variables exhibited good to excellent reliability. Conclusions: There was no difference between the digitization using the intraoral scanner or the laboratory scanner. The most accurate digitization technique was the 3 Shape laboratory scanner of the cast of the alginate impression. The inEos X5 showed the highest error of digitization of the alginate and rubber base impressions.

A new approach to retrieve leaf normal distribution using terrestrial laser scanners

Leaf normal distribution is an important structural characteristic of the forest canopy. Although terrestrial laser scanners（TLS） have potential for estimating canopy structural parameters, distinguishing between leaves and nonphotosynthetic structures to retrieve the leaf normal has been challenging. We used here an approach to accurately retrieve the leaf normals of camphorwood（Cinnamomum camphora） using TLS point cloud data.First, nonphotosynthetic structures were filtered by using the curvature threshold of each point. Then, the point cloud data were segmented by a voxel method and clustered by a Gaussian mixture model in each voxel. Finally, the normal vector of each cluster was computed by principal component analysis to obtain the leaf normal distribution. We collected leaf inclination angles and estimated the distribution, which we compared with the retrieved leaf normal distribution. The correlation coefficient between measurements and obtained results was 0.96, indicating a good coincidence.

Confocal 3D Optical Intraoral Scanners and Comparison of Image Capturing Accuracy

Several capture techniques are used in intraoral optical scanners in the dental market,such as Triangulation(Cerec Omnicam,Dentsply Sirona),Activewave front sampling(3M ESPE)and confocal technology(iTero,Align).The accuracy of intraoral scanners is the most significant focal point for developers to research.This in-vitro study studied the accuracy of confocal scanners launched from 2015-2020(Trios 3,Trios 4,iTero Element;3Shape Trios A/S,Copenhagen,Denmark,and iTero Element2,and iTero Element5D;Align Technologies,San Jose,CA,USA).A 3D printing model modified from the American National Standard No.132 was scanned five times each scanner.Both Trios3 and Trios4 were scanned using regular scan mode(N)and high-resolution mode(HR).All scanning methods followed the recommendations from the manufacturers.Then the digital models were exported and saved as STL files.Various measurements were determined in the digital model from each scan using Rhinoceros 3D Software(Rhino,Robert McNeel&Associates for Windows,Washington DC,USA).Measurements from the 3D printed model were used as control.All data were recorded in Microsoft Excel and then transferred to SPSS.Descriptive statistics were recorded.Multiple comparisons of various measurements were made among the different scanners and with the control using One-way ANOVA and post hoc using Sheffe(p<0.01).The surface area in the X and Y axis ranged from 2–60 mm,while the depth(Z-axis)ranged from 2–8 mm.The Trios and iTero families showed similar accuracy.However,for the diagonal,the Trios series showed better results compared with the iTero series.Within the same brand,different versions showed no significant change regarding accuracy.

Command functions of open loop galvanometer scanners with optimized duty cycles

The paper approaches the problem of the command functions of galvanometer-based scanners （GS） that are necessary to produce the linear plus parabolic scanning function of the GS, which we have proved previously to produce the highest possible duty cycle （i.e., time efficiency） of the device. We have completed this theoretical aspect （which contradicted what has been stated previously in the literature, where it has been considered that the linear plus sinusoidal scanning function was the best） with the experimental study of the most used scanning functions of the GSs （sawtooth, sinusoidal and triangular）, with applications in biomedical imaging, in particular in optical coherence tomography, demonstrating that the triangular function is always the best one to be applied, from both an optical and a mechanical point of view. In the present study the input voltage/command function which should be applied to the GS to produce the desired triangular scanning function （with controlled non-linearity for the fastest possible stop-and-turn portions） was determined analytically, in relationship with the active torque that drives the device. This command function is analyzed with regard to the specific, respectively required parameters of the GS： natural frequency and damping factor, respectively scan speed and amplitude. The modeling in an open loop control structure of the GS is finally discussed as a trade-off between using the highest possible duty cycle and minimizing the maximum peaks of the input voltage.

Design of fast adaptive readout system for wire scanners

A new wide-range fast readout system capable of adaptive identification is designed for wire scanners,which are used to measure beam profiles and emittance.This system is capable of handling varying current signals with Gaussian distributions and current pulses up to 1000 counts/s, as well as an input current range of 1 n A–1 m A. When tested, the resolution was found to exceed 3.68% for full scale, the nonlinearity was found to be less than 0.11%, and the measurement sensibility was found to be less than 5 p A. We believe that the system will play a crucial role in improving the measurement accuracy of beam diagnosis and the efficiency of accelerator operation,as well as decreasing the time required for beam tuning.This system was applied to the beam diagnosis of an injector II prototype for an accelerator-driven subcritical system and produced excellent measurement results. A description of the adaptive fast readout system for wire scanners is presented in this paper.

Effects of ramp vibrational states on flexural intrinsic vibrations inBesocke-style scanners

For both the vibrating and steady supporting surfaces of a scanning disk in a Besocke-style piezoelectric scanner, a theoretical model is given by considering the nonlinear lateral friction at the micro-contact interface between the positioning legs and the supporting surface. Numerical simulations demonstrate that unexpected flexural vibrations can arise from a vibrating ramp, and their frequencies are lower than the eigenfrequencies of the scanner in the linearly elastic regime. The vibrations essentially depend on 1） the vibrational states of the supporting ramp and the steel ball tips on the three piezo- electric positioning legs, and 2） the tribological characteristics of the contacts between the tips and the ramp. The results give an insight into the intrinsic vibrations of the scanners, and are applicable in designing and optimizing piezoelectric scanning systems.

Flexural resonance vibrations of piezoelectric ceramic tubes in Besocke-style scanners

Flexural resonance vibrations of piezoelectric ceramic tubes in Besocke-style scanners with nanometer resolution are studied by using an electro-mechanical coupling Timoshenko beam model. Meanwhile, the effects of friction, the first moment, and moment of inertia induced by mass loads are considered. The predicted resonance frequencies of the ceramic tubes are sensitive to not only the mechanical parameters of the scanners, but also the friction acting on the attached shaking ball and corresponding bending moment on the tubes. The theoretical results are in excellent agreement with the related experimental measurements. This model and corresponding results are applicable for optimizing the structures and performances of the scanners.

Displacement field reconstruction in landslide physical modeling by using a terrain laser scanner e Part 2:Application and large strain/displacement and water effect analysis

Deformation analysis is fundamental in geotechnical modeling.Nevertheless,there is still a lack of an effective method to obtain the deformation field under various experimental conditions.In this study,we introduce a processebased physical modeling of a pileereinforced reservoir landslide and present an improved deformation analysis involving large strains and water effects.We collect multieperiod point clouds using a terrain laser scanner and reconstruct its deformation field through a point cloud processing workflow.The results show that this method can accurately describe the landslide surface deformation at any time and area by both scalar and vector fields.The deformation fields in different profiles of the physical model and different stages of the evolutionary process provide adequate and detailed landslide information.We analyze the large strain upstream of the pile caused by the pile installation and the consequent violent deformation during the evolutionary process.Furthermore,our method effectively overcomes the challenges of identifying targets commonly encountered in geotechnical modeling where water effects are considered and targets are polluted,which facilitates the deformation analysis at the wading area in a reservoir landslide.Eventually,combining subsurface deformation as well as numerical modeling,we comprehensively analyze the kinematics and failure mechanisms of this complicated object involving landslides and pile foundations as well as water effects.This method is of great significance for any geotechnical modeling concerning large-strain analysis and water effects.

Innovative Scanners Boost Medical Imaging Quality and Utility

During his 30-year career,radiologist Philippe Douek has pored over thousands of images produced by computed tomography(CT)scanners,looking for signs of illness or injury.But the professor of radiology at the University Claude Bernard Lyon 1 in France,was wowed by the performance of a new type of device known as a photon-counting detector(PCD)CT scanner.Douek and his colleagues have been putting prototype PCD machines through their paces,scanning animals,imaging dummies,and even Douek’s lungs.The images produced with the technology“are much more detailed,”he said.

Geometric Calibration of Low-Cost Flatbed Scanners for Large Scale Mapping Applications

Scanning hardcopy non-metric images is one of the most important sources in digital mapping. Low-cost scanners are still widely used in many applications as they can produce digital images of comparable precisions to those produced by expensive professional scanners. Yet, inexpensive scanners introduce geometrical distortions in the measured image coordinates that must be assessed and compensated before using their products for further analysis. In this article, several 2D-to-2D transformation models were investigated to calibrate flatbed scanners with different resolutions and sizes. We evaluated the potential of each model using two gridded-crosses plotted on high-quality transparent sheets. Control coordinates were provided through a photogram-metric analytical plotter. After scanning the sheets, least squares matching was applied to determine the precise locations of the crosses. By comparing the control coordinates and those estimated from digitized images, it was found that the mathematical model based on the projective transformation gives the best results for standardizing the geometric properties of flatbed scanners. The results show that scanning resolution of 2400 dpi achieves the requirements for large-scale mapping applications.

Computer-Aided Design of X-Ray Microtomographic Scanners

The article is to study the development of computer-aided design of X-ray microtomography—the device for investigating the structure and construction of three-dimensional images of organic and inorganic objects on the basis of shadow projections. This article provides basic information regarding CAD of X-ray microtomography and a scheme consisting of three levels. The article also shows basic relations of X-ray computed tomography, the generalized scheme of an X-ray microtomographic scanner. The methods of X-ray imaging of the spatial microstructure and morphometry of materials are described. The main characteristics of an X-ray microtomographic scanner, the X-ray source, X-ray optical elements and mechanical components of the positioning system are shown. The block scheme and software functional scheme for intelligent neural network system of analysis of the internal microstructure of objects are presented. The method of choice of design parameters of CAD of X-ray microtomography aims at improving the quality of design and reducing costs of it. It is supposed to reduce the design time and eliminate the growing number of engineers involved in development and construction of X-ray microtomographic scanners.

Displacement field reconstruction in landslide physical modeling by using a terrain laser scanner e Part 1:Methodology,error analysis and validation

Laser scanning technology has been widely used in landslide aspects.However,the existing deformation analysis based on terrain laser scanners can only provide limited information,which is insufficient for understanding landslide kinematics and failure mechanisms.To overcome this limitation,this paper proposes an automated method for processing point clouds collected in landslide physical modeling.This method allows the acquisition of quantitative three-dimensional(3D)deformation field information.The results show the organized and spatially related point cloud segmentation in terms of spherical targets.The segmented point clouds can be fitted to determine the locations of all preset targets and their corresponding location changes.The proposed method has been validated based on theoretical analysis and numerical and physical tests,which indicates that it can batch-process massive data sets with high computational efficiency and good noise resistance.Compared to existing methods,this method shows a significant potential for understanding landslide kinematics and failure mechanisms and advancing the application of 3D laser scanning in geotechnical modeling.

基于PhotoModeler Scanner的普通数码相机快速检校研究

随着分辨率的不断提高与价格的日益降低,数码相机已成为近景摄影测量的基本设备,而相机的准确检校是保证量测精度的关键因素。借助于PhotoModeler Scanner软件,本文实现了相机的快速准确检校,并对野外检校的稳定性和质量进行了分析,说明该检校方法简便可靠。

固井质量评价仪Isolation Scanner在塔里木油田套管检测方面的应用

塔里木油田地质构造复杂,油气埋藏普遍偏深,深井、超深井钻井工艺复杂,套管柱结构多样,如何检测钻井和后续开发造成的套管磨损和腐蚀情况,成为测井工程的一大难题。为了解决该难题,油田引进了最新一代的固井质量评价仪Isolation Scanner,该仪器通过脉冲回波测量和挠曲波衰减测量,可对套管结构进行检测,同时对套管磨损、腐蚀及套管居中情况进行定量评价。详细介绍了Isolation Scanner仪器的工作原理,并介绍了该仪器在塔里木油田套管检测方面的应用情况,通过实例分析认为该仪器的应用效果良好。

新型核磁共振测井仪MR Scanner性能及其应用

斯伦贝谢公司2006年新推出了核磁共振测井仪器MR Scanner,该仪器采用偏心梯度设计,具有提供多种探测深度、测量结果不受井眼条件的影响、能进行流体表征等特点。在低阻、低对比度储层的评价中具有较大优势。文章对MR Scanner仪器的结构、特点、规格及技术指标进行了介绍,列举了其优点以及应用效果。

Isolation Scanner套后成像测井找漏技术在H油田的应用

塔里木盆地H油田整体采用超深水平井开发,近年套损现象呈增加趋势。目前常用套损井找漏技术效果不理想。针对该现状提出了Isolation Scanner套后成像测井(IBC)找漏技术,该技术能同时测量套管内径和壁厚变化,定量评价内部腐蚀和外部腐蚀,分辨率高,在H油田H68水平井应用成功,该技术为H油田类似油水井找漏提供了技术指导和实际经验。

斯伦贝谢新型高清晰度能谱测井仪——Litho Scanner的崛起

本文详细介绍了斯伦贝谢推出的新型高清晰度测井仪——LithoScanner,该仪器具有仪器外径小、测速快、不受井眼类型及温度限制等特点。仪器采用独特的LaBr3:Ce伽马探测器、优良的脉冲中子发射器(PNG),同时采集非弹性散射伽马能谱和俘获伽马能谱,高中子输出、高计数率为提高元素测量的准确度和精度奠定了扎实基础。得到的准确矿物含量和总有机碳含量(TOC),为评价非常规油气藏提供了有利证据。本文还介绍了该仪器规格、工作流程及其应用。

浅谈利用Scanner、System输入和输出数据

介绍了在Java语言中利用Scanner类从键盘输入数据、System输出数据的方法,通过两个应用实例设计实现了从键盘输入数据、从控制台输出数据。