All-solid-state lithium batteries(ASSLBs)based on sulfide solid electrolytes(SEs)are one of the most promising strategies for next-generation energy storage systems and electronic devices.However,the poor chemical/ele...All-solid-state lithium batteries(ASSLBs)based on sulfide solid electrolytes(SEs)are one of the most promising strategies for next-generation energy storage systems and electronic devices.However,the poor chemical/electrochemical stability of sulfide SEs with oxide cathode materials and high interfacial impedance,particularly due to physical contact failure,are the major limiting factors to the development of sulfide SEs in ASSLBs.Herein,the composite cathode of MOF-derived Fe_(7)S_(8)@C and Li_(6)PS_(5)Br fabricated by an infiltration method(IN-Fe_(7)S_(8))with dissoluble sulfide electrolyte(dissoluble SE)is reported.Dissoluble SE can easily infiltrate the porous sheet-type Fe_(7)S_(8)@C cathode to homogeneously contact with Fe_(7)S_(8)nanoparticles that are embedded in the surrounding carbon matrixes and form a fast ionic transport network.Benefiting from applying dissoluble SE and Fe_(7)S_(8)@C,the IN-Fe_(7)S_(8)-based cells displayed a reversible capacity of 510 mAh g^(-1)after 180 cycles at 0.045 mA cm^(-2)at 30℃.This work demonstrates a novel and practical method for the development of high-performance all-sulfide-based solid state batteries.展开更多
The kinetics of Cr（Ⅵ） reduction by sulfide in soil suspensions with various pHs, soil compositions, and Fe（Ⅱ） concentrations was examined using batch anaeroblc experimental systems at constant temperature. The r...The kinetics of Cr（Ⅵ） reduction by sulfide in soil suspensions with various pHs, soil compositions, and Fe（Ⅱ） concentrations was examined using batch anaeroblc experimental systems at constant temperature. The results showed that the reaction rate of Cr（Ⅵ） reduction was in the order of red soil 〈 yellow-brown soil 〈 chernozem and was proportional to the concentration of HCl-extractable iron in the soils. Dissolved and adsorbed iron in soil suspensions played an important role in accelerating Cr（Ⅵ） reduction. The reaction involved in the Cr（Ⅵ） reduction by Fe（Ⅱ） to produce Fe（ⅡI）, which was reduced to Fe（Ⅱ） again by sulfide, could represent the catalytic pathway until about 70% of the initially present Cr（Ⅵ） was reduced. The catalysis occurred because the one-step reduction of Cr（Ⅵ） by sulfide was slower than the two-step process consisting of rapid Cr（Ⅵ） reduction by Fe（Ⅱ） followed by Fe（Ⅲ） reduction by sulfide. In essence, Fe（Ⅱ）/Fe（Ⅲ） species shuttle electrons from sulfide to Cr（Ⅵ）, facilitating the reaction. The effect of iron, however, could be completely blocked by adding a strong Fe（Ⅱ）-complexing ligand, 1,10-phenanthroline, to the soil suspensions. In all the experiments, initial sulfide concentration was much higher than initial Cr（Ⅵ） concentration. The plots of In e[Cr（Ⅵ）] versus reaction time were linear up to approximately 70% of Cr（Ⅵ） reduction, suggesting a first-order reaction kinetics with respect to Cr（Ⅵ）. Elemental sulfur, the product of sulfide oxidation, was found to accelerate Cr（Ⅵ） reduction at a later stage of the reaction, resulting in deviation from linearity for the In c[Cr（Ⅵ）] versus time plots.展开更多
Iron sulfide minerals are widely distributed, of which characteristics had the identification significance of formation environment. Previously, there were more research on iron sulfide minerals under hydrothermal con...Iron sulfide minerals are widely distributed, of which characteristics had the identification significance of formation environment. Previously, there were more research on iron sulfide minerals under hydrothermal condition, and few studies under volcanism formation condition. To simulate volcanic mineralization, the study of different temperature from 250 to 410℃ , different iron sulfur ratio from Fe:S=2∶1 to 1∶8, and two different sources of iron, reduced iron powder (Fe) and ferrous sulfide (FeS), on iron sulfide mineral evolution was investigated under thermal sulfurization condition. By using scanning electron microscopy (SEM), X-ray diffraction (XRD) and other methods, the morphology, composition and structural characteristics of the products were observed and analyzed.展开更多
Cadmium(Cd),lead(Pb),and hexavalent chromium(Cr(Ⅵ)) are often found in soils and water affected by metal smelting,chemical manufacturing,and electroplating.In this study,synthetic iron sulfide nanoparticles(FeS NPs) ...Cadmium(Cd),lead(Pb),and hexavalent chromium(Cr(Ⅵ)) are often found in soils and water affected by metal smelting,chemical manufacturing,and electroplating.In this study,synthetic iron sulfide nanoparticles(FeS NPs) were stabilized with carboxymethyl cellulose(CMC) and utilized to remove Cr(Ⅵ),Cd,and Pb from an aqueous solution.Batch experiments,a Visual MINTEQ model,scanning electron microscopy(SEM),X-ray diffraction(XRD),and X-ray photoelectron spectrometer(XPS) analysis were used to determine the removal efficiencies,influencing factors,and mechanisms.The FeS NP suspension simultaneously removed Cr(Ⅵ),Cd,and Pb from an aqueous solution.The concentrations of Cr(Ⅵ),Cd,and Pb decreased from 50,10,and 50 mg·L^(-1) to 2.5,0.1,and 0.1 mg·L^(-1),respectively.The removal capacities were up to 418,96,and 585 mg per gram of stabilized FeS NPs,respectively.The acidic conditions significantly favored the removal of aqueous Cr(Ⅵ) while the alkaline conditions favored the removal of Cd and Pb.Oxygen slightly inhibited the removal of Cr(Ⅵ),but it had no significant influence on the removal of Cd and Pb.A potential mechanism was proposed for the simultaneous removal of Cr(Ⅵ),Cd,and Pb using FeS NPs.The interactions of the three heavy metals involved a cationic bridging effect on Cr(Ⅵ) by Cd,an enhanced adsorption effect on Cd by [Cr,Fe](OH)_3,precipitation of PbCrO_4,and transformation of PbCrO_4 to PbS.Therefore,FeS NPs have a high potential for use in the simultaneous removal of Cr(Ⅵ),Cd,and Pb from contaminated aqueous solutions.展开更多
Iron sulfide is an important reductive pollutant in aquatic sediment,so that increasing attentions have been paid to it in recent years.In this paper,the formation of iron sulfide in water-body sediment was introduced...Iron sulfide is an important reductive pollutant in aquatic sediment,so that increasing attentions have been paid to it in recent years.In this paper,the formation of iron sulfide in water-body sediment was introduced.Moreover,its adverse influences upon environment were summarized,including direct contribution to deficiency of dissolved oxygen in water,association with eutrophication in water-bodies and impact on geochemical sulfur cycle.Since conventional chemical analysis for iron sulfide has several disadvantages,new technique for rapid determination of iron sulfide on-line was prospected.展开更多
Presence of iron and manganese in water not only affects the organoleptic properties of water, but also can cause a number of problems in drinking water treatments. Their removal in drinking water preparation processe...Presence of iron and manganese in water not only affects the organoleptic properties of water, but also can cause a number of problems in drinking water treatments. Their removal in drinking water preparation processes becomes more complicated in the presence of hydrogen sulfide and ammonia in water. There are certain commercialized products at the market that are used for removal of manganese, iron and ammonia, but it is of crucial importance to establish an appropriate order of removal in the technological process during drinking water treatment. Through the various combinations of commercialized filtration media, the removal of iron, manganese, hydrogen sulfide and ammonia, was being examined and on the basis of obtained results their effectiveness was estimated. Research results have shown that hydrogen sulfide is pollutant that causes problems during the adsorption in removing manganes. Ammonia, which is bonded to hydrogen sulphide influences the volume of treated water when it comes to removing the iron and manganese. Decrease in the concentration of hydrogen sulfide at the entrance to Filtersorb FMH for four times, has led to an increase in the volume of treated water in the amount of two times, followed by the breakthrough point of concentration of manganese. For complete usage capacity of commercialized products for the removal of these pollutants, finding their mutual bond in compounds which are present in the water, is of the importance.展开更多
PdCl 2 (CH 3) 3CC 6H 4SC 4H 9- S 2, C 28 H 44 Cl 2S 2Pd, M r =622.0756, triclinic, space group P1, a=10.403(2), b=12.346(2), c=13.475(2) , α=89 11(1)°, β=75.44(1)°, γ=69.52(...PdCl 2 (CH 3) 3CC 6H 4SC 4H 9- S 2, C 28 H 44 Cl 2S 2Pd, M r =622.0756, triclinic, space group P1, a=10.403(2), b=12.346(2), c=13.475(2) , α=89 11(1)°, β=75.44(1)°, γ=69.52(1)°, V=1564.2(5) 3, Z=2, D c =1.32 g/cm 3, Mo Kα radiation, μ =9.00 cm -1 , F(000)=647.95, R =0.0316 for 4561 observed reflections with I≥3σ(I) . Pd(Ⅱ) is coordinated by two chloride atoms and two sulfur atoms of organic ligands, forming a rhombic quadrilateral plane with Pd-S of 2.325(1) and Pd-Cl of 2.295(1) .展开更多
Zinc leaching residue(ZLR) contains high content of valuable metals such as zinc and iron. However, zinc and iron mainly exist in the form of zinc ferrite, which are difficult to separate and recover. This study propo...Zinc leaching residue(ZLR) contains high content of valuable metals such as zinc and iron. However, zinc and iron mainly exist in the form of zinc ferrite, which are difficult to separate and recover. This study proposed a new process involving sulfidation roasting, magnetic separation and flotation to recover zinc and iron in ZLR. Through sulfidation roasting of ZLR with pyrite, zinc and iron were converted into ZnS and Fe3 O4. The effects of pyrite dosage, roasting temperature and roasting time on the sulfidation of zinc in ZLR were investigated. The results showed that the sulfidation percentage of zinc reached 91.8% under the optimum condition. Besides, it was found that ball-milling was favorable for the separation and recovery of zinc and iron in sulfidation products. After ball-milling pretreatment, iron and zinc were enriched from sulfidation products by magnetic separation and flotation. The grade of iron in magnetic concentrates was 52.3% and the grade of zinc in flotation concentrates was 31.7%, which realized the recovery of resources.展开更多
A selective and sensitive reagent of 2-pyridine carboxaldehyde isonicotinyl hydrazone（2-PYAINH） was synthesized and studied for the spectrophotometric determination of nickel, copper, cobalt, and iron in detail. At ...A selective and sensitive reagent of 2-pyridine carboxaldehyde isonicotinyl hydrazone（2-PYAINH） was synthesized and studied for the spectrophotometric determination of nickel, copper, cobalt, and iron in detail. At a pH value of 7.0, 9,0, 9.0, and 8.0, respectively, which greatly increased the selectivity; nickel, copper, cobalt, and iron reacted with 2-PYAINH to form a 1：2 yellow-orange, 1：2 yellow-green, 1：2 yellow and 1：1 yellow complexes, with absorption peaks at 363, 352, 346, and 359 nm, respectively. Under the optimal conditions, Beer＇s law was obeyed over the ranges of 0.01-1.4, 0.01-1.5, 0.01-2.7, and 0.01-5.4 mg/L respectively. The apparent molar absorptivity and Sandell＇s sensitivities were 8.4×10^4, 5.2×10^4, 7.1×10^4, and 3.9×10^4 L·mol^-l·cm^-1, respectively, and 0.00069, 0.0012, 0.00078, and 0.0014 μg·cm2, respectively. The detection limits were found to be 0.001, 0.002, 0.003, and 0.01 mg/L, respectively. The detailed study of various interfering ions to make the method more sensitive was carried out and selective and several real samples were analyzed with satisfactory results.展开更多
Optimization of factors influencing the experiments on reactions involving 8 different chelating agents and soluble Fe(III)/Fe(II) salts was carried out to yield chelated iron complexes. A combination of optimized inf...Optimization of factors influencing the experiments on reactions involving 8 different chelating agents and soluble Fe(III)/Fe(II) salts was carried out to yield chelated iron complexes. A combination of optimized influencing factors has resulted in a Fe chelating capacity of the iron-based desulfurization solution to be equal to 6.83—13.56 g/L at a redox potential of 0.185—0.3. The desulfurization performance of Fe(III)/Fe(II) chelating agents was investigated on a simulated sulfur-containing industrial gas composed of H2 S and N2 in a cross-flow rotating packed bed. Test results have revealed that the proposed iron-based desulfurization solution showed a sulfur removal efficiency of over 99% along with a Fe chelating capacity exceeding 1.35 g/L. This desulfurization technology which has practical application prospect is currently in the phase of commercial scale-up study.展开更多
The corrosion behavior of spheroidal graphite and flake graphite cast irons was studied in oxidizing and sulfidizing atmospheres between 600 and 800℃ for 50 h. The corrosion rate in the sulfidizing atmosphere was fas...The corrosion behavior of spheroidal graphite and flake graphite cast irons was studied in oxidizing and sulfidizing atmospheres between 600 and 800℃ for 50 h. The corrosion rate in the sulfidizing atmosphere was faster than that in air above 700℃, due to the formation of the Fe0.975S sulfide. The corrosion rate of the spheroidal graphite cast iron was similar to that of the flake graphite cast iron.展开更多
Iron(Ⅱ) tetrasulfophthalocyanine(FeTSPc) ,as a novel mimetic enzyme of peroxidase,was used in the synthesis of a conducting polyaniline(PANI) /sodium dodecylsulfate(SDS) complex in SDS aqueous micellar solutions. The...Iron(Ⅱ) tetrasulfophthalocyanine(FeTSPc) ,as a novel mimetic enzyme of peroxidase,was used in the synthesis of a conducting polyaniline(PANI) /sodium dodecylsulfate(SDS) complex in SDS aqueous micellar solutions. The effects of pH,concentrations of aniline,SDS and H2O2,and reaction time on polymerization of aniline were studied in this case as shown by UV-Vis absorption spectroscopy. The results show that a wide range of pH(0.5-4.0) is required to produce the conducting PANI,and the optimal pH is 1.0 in SDS micelle. The optimal concentrations of aniline,SDS and H2O2 in feed,and reaction time in this case for the production of conducting PANI are respectively 10 mmol/L,10 mmol/L,25 mmol/L,and 15 h. FT-IR spectrum,elemental analysis,conductivity,cyclic voltammetry and thermogravimetric analysis confirm the thermal stability and electroactive form of PANI.展开更多
A coordination polymer based on iron（II） carboxylate helical chains [Fe（bpdc）（H2O）2]n 1 has been constructed hydrothermally using H2bpdc （H2bpdc = 2,2＇-bipyridine-4,4＇-dicarboxylic acid）, pyridine and FeSO4&...A coordination polymer based on iron（II） carboxylate helical chains [Fe（bpdc）（H2O）2]n 1 has been constructed hydrothermally using H2bpdc （H2bpdc = 2,2＇-bipyridine-4,4＇-dicarboxylic acid）, pyridine and FeSO4·7H2O. Its crystal structure reveals that the Fe（Ⅱ） ion adopts a slightly distorted octahedron. The carboxylates of bpdc ligands alternately bridge the Fe（Ⅱ） cations to form 1D infinite helical chains. The Fe···Fe intrachain distance is 4.8246（6） . The adjacent chains are further interlinked by the coordination of bpdc ligands and hydrogen bonding to form a 3D framework. Magnetic studies for complex 1 show weak antiferromagnetic coupling between the Fe（Ⅱ） ions. The best-fit for χM T vs. T with a Hamiltonian∑∑==iBiiHJSi SigHS11 leadsto g = 2.314（4） and J = –0.68（1） cm-1.展开更多
An iron（Ⅱ） coordination polymer, [Fe（Haip）2（H2O）2]n （1, Haip = 5-ammoniumiso- phthalato）, has been hydro/solvothermally synthesized and characterized by single-crystal X-ray diffraction, elemental analysis, i...An iron（Ⅱ） coordination polymer, [Fe（Haip）2（H2O）2]n （1, Haip = 5-ammoniumiso- phthalato）, has been hydro/solvothermally synthesized and characterized by single-crystal X-ray diffraction, elemental analysis, infrared spectrum and magnetic measurement. Compound 1 crystalizes in monoclinic, space group P2/c with a = 6.9874（14）, b = 9.960（2）, c = 12.894（4） A, β = 117.47（2）°, Fe（C8H6NO4）2（H2O）2, Mr = 452.16, V= 796.2（3） A3, Z = 2, Dc = 1.886 g.cm-3, p = 1.017 mm-1, F（000） = 464.0, 2.71〈0〈28.42°, R = 0.0307, wR = 0.0840 and S = 1.005. Single-crystal X-ray diffraction analysis reveals that 1 features an infinite one-dimensional loop-like chain structure and Haip ligand in 1 is of zwitterionic form. Magnetic measurement results show the dominated ferromagnetic interactions among Fe11 atoms.展开更多
Fe–S compounds with hexagonal crystal structure are potential hydrogen permeation barrier during H2S corrosion. Hexagonal system Fe–S films were prepared on carbon steel through corrosion and CVD deposition, and the...Fe–S compounds with hexagonal crystal structure are potential hydrogen permeation barrier during H2S corrosion. Hexagonal system Fe–S films were prepared on carbon steel through corrosion and CVD deposition, and the barrier effect of different Fe–S films on hydrogen permeation was tested using electrochemical hydrogen permeation method. After that, the electrical properties of Fe–S compound during phase transformation were measured using thermoelectric measurement system. Results show that the mackinawite has no obvious barrier effect on hydrogen penetration, as a p-type semiconductor, and pyrrhotite (including troilite) has obvious barrier effect on hydrogen penetration,as an n-type semiconductor. Hydrogen permeation tests showed peak permeation performance when the surface was deposited with a continuous film of pyrrhotite (Fe_(1–x)S) and troilite. The FeS compounds suppressed hydrogen permeation by the promotion of the hydrogen evolution reaction, semiconducting inversion from p-to n-type, and the migration of ions at the interface.展开更多
Cobalt-phthalocyanine/iron nanocomposite particles have been obtained using method of composite in situ, with the mixture of carbonyl iron and solution of cobalt ( Ⅱ ) - phthalocyanine (Co-Pc) ultrasonic dispersing i...Cobalt-phthalocyanine/iron nanocomposite particles have been obtained using method of composite in situ, with the mixture of carbonyl iron and solution of cobalt ( Ⅱ ) - phthalocyanine (Co-Pc) ultrasonic dispersing in N,N-dimethyl-formamide (DMF). Structure characterization of their inner and surface have relation with method of carbonyl iron joined in the mixture, contents of carbonyl iron and Co-Pc in the mixture of Co-Pc ultrasonic dispersing in DMF. With a method of composite in situ controlling reasonable experiment condition, it can be obtained that cobalt-phthalocyanine/iron nanocomposite particles has completely been covered with Co-Pc, they had structure of Chinese gooseberry in inner and mere made up of almost regular spherical shape and the average diameter is 1. 4 μm.展开更多
Magnetorheological suspension based on 20 (v/V) % CoPc-iron composite particles dispersed in sili-cone oil have been obtained, which exhibited dynamic shear stress up to 2000Pa upon application of external magnetic fi...Magnetorheological suspension based on 20 (v/V) % CoPc-iron composite particles dispersed in sili-cone oil have been obtained, which exhibited dynamic shear stress up to 2000Pa upon application of external magnetic field at 1300 Oe. The response is faster than 0. 15 -with superior reversibility of changes in viscosity induced by external magnetic field at above 12. 5℃. Further, it was found that the MR fluid is in possession of long-term stability a-gainst sedimentation.展开更多
基金supported by the Guangdong“Pearl River Talents Plan”(no.2017GC010218)R&D Program in Key Areas of Guangdong Province(no.2020B0101030005)+2 种基金Guangdong Basic and Applied Basic Research Foundation(nos.2020B15151200492021A1515010153)the National Natural Science Foundation of China(no.NSFC51621001).
文摘All-solid-state lithium batteries(ASSLBs)based on sulfide solid electrolytes(SEs)are one of the most promising strategies for next-generation energy storage systems and electronic devices.However,the poor chemical/electrochemical stability of sulfide SEs with oxide cathode materials and high interfacial impedance,particularly due to physical contact failure,are the major limiting factors to the development of sulfide SEs in ASSLBs.Herein,the composite cathode of MOF-derived Fe_(7)S_(8)@C and Li_(6)PS_(5)Br fabricated by an infiltration method(IN-Fe_(7)S_(8))with dissoluble sulfide electrolyte(dissoluble SE)is reported.Dissoluble SE can easily infiltrate the porous sheet-type Fe_(7)S_(8)@C cathode to homogeneously contact with Fe_(7)S_(8)nanoparticles that are embedded in the surrounding carbon matrixes and form a fast ionic transport network.Benefiting from applying dissoluble SE and Fe_(7)S_(8)@C,the IN-Fe_(7)S_(8)-based cells displayed a reversible capacity of 510 mAh g^(-1)after 180 cycles at 0.045 mA cm^(-2)at 30℃.This work demonstrates a novel and practical method for the development of high-performance all-sulfide-based solid state batteries.
文摘The kinetics of Cr（Ⅵ） reduction by sulfide in soil suspensions with various pHs, soil compositions, and Fe（Ⅱ） concentrations was examined using batch anaeroblc experimental systems at constant temperature. The results showed that the reaction rate of Cr（Ⅵ） reduction was in the order of red soil 〈 yellow-brown soil 〈 chernozem and was proportional to the concentration of HCl-extractable iron in the soils. Dissolved and adsorbed iron in soil suspensions played an important role in accelerating Cr（Ⅵ） reduction. The reaction involved in the Cr（Ⅵ） reduction by Fe（Ⅱ） to produce Fe（ⅡI）, which was reduced to Fe（Ⅱ） again by sulfide, could represent the catalytic pathway until about 70% of the initially present Cr（Ⅵ） was reduced. The catalysis occurred because the one-step reduction of Cr（Ⅵ） by sulfide was slower than the two-step process consisting of rapid Cr（Ⅵ） reduction by Fe（Ⅱ） followed by Fe（Ⅲ） reduction by sulfide. In essence, Fe（Ⅱ）/Fe（Ⅲ） species shuttle electrons from sulfide to Cr（Ⅵ）, facilitating the reaction. The effect of iron, however, could be completely blocked by adding a strong Fe（Ⅱ）-complexing ligand, 1,10-phenanthroline, to the soil suspensions. In all the experiments, initial sulfide concentration was much higher than initial Cr（Ⅵ） concentration. The plots of In e[Cr（Ⅵ）] versus reaction time were linear up to approximately 70% of Cr（Ⅵ） reduction, suggesting a first-order reaction kinetics with respect to Cr（Ⅵ）. Elemental sulfur, the product of sulfide oxidation, was found to accelerate Cr（Ⅵ） reduction at a later stage of the reaction, resulting in deviation from linearity for the In c[Cr（Ⅵ）] versus time plots.
基金Supported by National Natural Science Foundation (Grant No.:40872045 41172047)The Opening Project of Key Laboratory of Solid Waste Treatment and Resource Recycle (SWUST), Ministry of Education (12zxgk01)
文摘Iron sulfide minerals are widely distributed, of which characteristics had the identification significance of formation environment. Previously, there were more research on iron sulfide minerals under hydrothermal condition, and few studies under volcanism formation condition. To simulate volcanic mineralization, the study of different temperature from 250 to 410℃ , different iron sulfur ratio from Fe:S=2∶1 to 1∶8, and two different sources of iron, reduced iron powder (Fe) and ferrous sulfide (FeS), on iron sulfide mineral evolution was investigated under thermal sulfurization condition. By using scanning electron microscopy (SEM), X-ray diffraction (XRD) and other methods, the morphology, composition and structural characteristics of the products were observed and analyzed.
基金supported by the National Natural Science Foundation of China (51778084)the National key Research&Development program of China (2018YFC1800305)+2 种基金the Chongqing Ecology and Environment Bureau (2019-128)the Sichuan Science and Technology Program (2019YFSY0005)the Large Instruments Open Foundation of Chongqing University (201903150051)。
文摘Cadmium(Cd),lead(Pb),and hexavalent chromium(Cr(Ⅵ)) are often found in soils and water affected by metal smelting,chemical manufacturing,and electroplating.In this study,synthetic iron sulfide nanoparticles(FeS NPs) were stabilized with carboxymethyl cellulose(CMC) and utilized to remove Cr(Ⅵ),Cd,and Pb from an aqueous solution.Batch experiments,a Visual MINTEQ model,scanning electron microscopy(SEM),X-ray diffraction(XRD),and X-ray photoelectron spectrometer(XPS) analysis were used to determine the removal efficiencies,influencing factors,and mechanisms.The FeS NP suspension simultaneously removed Cr(Ⅵ),Cd,and Pb from an aqueous solution.The concentrations of Cr(Ⅵ),Cd,and Pb decreased from 50,10,and 50 mg·L^(-1) to 2.5,0.1,and 0.1 mg·L^(-1),respectively.The removal capacities were up to 418,96,and 585 mg per gram of stabilized FeS NPs,respectively.The acidic conditions significantly favored the removal of aqueous Cr(Ⅵ) while the alkaline conditions favored the removal of Cd and Pb.Oxygen slightly inhibited the removal of Cr(Ⅵ),but it had no significant influence on the removal of Cd and Pb.A potential mechanism was proposed for the simultaneous removal of Cr(Ⅵ),Cd,and Pb using FeS NPs.The interactions of the three heavy metals involved a cationic bridging effect on Cr(Ⅵ) by Cd,an enhanced adsorption effect on Cd by [Cr,Fe](OH)_3,precipitation of PbCrO_4,and transformation of PbCrO_4 to PbS.Therefore,FeS NPs have a high potential for use in the simultaneous removal of Cr(Ⅵ),Cd,and Pb from contaminated aqueous solutions.
基金Supported by Homecoming Foundation of Heilongjiang Province(LC06C04)Researcher Overseas Foundation of the Department of Education of Heilongjiang Province(1152hq19)
文摘Iron sulfide is an important reductive pollutant in aquatic sediment,so that increasing attentions have been paid to it in recent years.In this paper,the formation of iron sulfide in water-body sediment was introduced.Moreover,its adverse influences upon environment were summarized,including direct contribution to deficiency of dissolved oxygen in water,association with eutrophication in water-bodies and impact on geochemical sulfur cycle.Since conventional chemical analysis for iron sulfide has several disadvantages,new technique for rapid determination of iron sulfide on-line was prospected.
基金supported by the Ministry of Education,Science and Technological Development of the Republic of Serbia,Project Number OI 176018.
文摘Presence of iron and manganese in water not only affects the organoleptic properties of water, but also can cause a number of problems in drinking water treatments. Their removal in drinking water preparation processes becomes more complicated in the presence of hydrogen sulfide and ammonia in water. There are certain commercialized products at the market that are used for removal of manganese, iron and ammonia, but it is of crucial importance to establish an appropriate order of removal in the technological process during drinking water treatment. Through the various combinations of commercialized filtration media, the removal of iron, manganese, hydrogen sulfide and ammonia, was being examined and on the basis of obtained results their effectiveness was estimated. Research results have shown that hydrogen sulfide is pollutant that causes problems during the adsorption in removing manganes. Ammonia, which is bonded to hydrogen sulphide influences the volume of treated water when it comes to removing the iron and manganese. Decrease in the concentration of hydrogen sulfide at the entrance to Filtersorb FMH for four times, has led to an increase in the volume of treated water in the amount of two times, followed by the breakthrough point of concentration of manganese. For complete usage capacity of commercialized products for the removal of these pollutants, finding their mutual bond in compounds which are present in the water, is of the importance.
文摘PdCl 2 (CH 3) 3CC 6H 4SC 4H 9- S 2, C 28 H 44 Cl 2S 2Pd, M r =622.0756, triclinic, space group P1, a=10.403(2), b=12.346(2), c=13.475(2) , α=89 11(1)°, β=75.44(1)°, γ=69.52(1)°, V=1564.2(5) 3, Z=2, D c =1.32 g/cm 3, Mo Kα radiation, μ =9.00 cm -1 , F(000)=647.95, R =0.0316 for 4561 observed reflections with I≥3σ(I) . Pd(Ⅱ) is coordinated by two chloride atoms and two sulfur atoms of organic ligands, forming a rhombic quadrilateral plane with Pd-S of 2.325(1) and Pd-Cl of 2.295(1) .
基金Project(2018YFC1900305)supported by the National Key R&D Program of ChinaProject(51825403)supported by the National Science Foundation for Distinguished Young Scholars,China+1 种基金Projects(51634010,51474247,51904354)supported by the National Natural Science Foundation of ChinaProject(2019SK2291)supported by the Key Research and Development Program of Hunan Province,China。
文摘Zinc leaching residue(ZLR) contains high content of valuable metals such as zinc and iron. However, zinc and iron mainly exist in the form of zinc ferrite, which are difficult to separate and recover. This study proposed a new process involving sulfidation roasting, magnetic separation and flotation to recover zinc and iron in ZLR. Through sulfidation roasting of ZLR with pyrite, zinc and iron were converted into ZnS and Fe3 O4. The effects of pyrite dosage, roasting temperature and roasting time on the sulfidation of zinc in ZLR were investigated. The results showed that the sulfidation percentage of zinc reached 91.8% under the optimum condition. Besides, it was found that ball-milling was favorable for the separation and recovery of zinc and iron in sulfidation products. After ball-milling pretreatment, iron and zinc were enriched from sulfidation products by magnetic separation and flotation. The grade of iron in magnetic concentrates was 52.3% and the grade of zinc in flotation concentrates was 31.7%, which realized the recovery of resources.
文摘A selective and sensitive reagent of 2-pyridine carboxaldehyde isonicotinyl hydrazone（2-PYAINH） was synthesized and studied for the spectrophotometric determination of nickel, copper, cobalt, and iron in detail. At a pH value of 7.0, 9,0, 9.0, and 8.0, respectively, which greatly increased the selectivity; nickel, copper, cobalt, and iron reacted with 2-PYAINH to form a 1：2 yellow-orange, 1：2 yellow-green, 1：2 yellow and 1：1 yellow complexes, with absorption peaks at 363, 352, 346, and 359 nm, respectively. Under the optimal conditions, Beer＇s law was obeyed over the ranges of 0.01-1.4, 0.01-1.5, 0.01-2.7, and 0.01-5.4 mg/L respectively. The apparent molar absorptivity and Sandell＇s sensitivities were 8.4×10^4, 5.2×10^4, 7.1×10^4, and 3.9×10^4 L·mol^-l·cm^-1, respectively, and 0.00069, 0.0012, 0.00078, and 0.0014 μg·cm2, respectively. The detection limits were found to be 0.001, 0.002, 0.003, and 0.01 mg/L, respectively. The detailed study of various interfering ions to make the method more sensitive was carried out and selective and several real samples were analyzed with satisfactory results.
基金financially supported by the Natural Science Fundation of China (No.21376229) the Science and Technology Development Plan of Shanxi Province,China (No.20130321035-02)
文摘Optimization of factors influencing the experiments on reactions involving 8 different chelating agents and soluble Fe(III)/Fe(II) salts was carried out to yield chelated iron complexes. A combination of optimized influencing factors has resulted in a Fe chelating capacity of the iron-based desulfurization solution to be equal to 6.83—13.56 g/L at a redox potential of 0.185—0.3. The desulfurization performance of Fe(III)/Fe(II) chelating agents was investigated on a simulated sulfur-containing industrial gas composed of H2 S and N2 in a cross-flow rotating packed bed. Test results have revealed that the proposed iron-based desulfurization solution showed a sulfur removal efficiency of over 99% along with a Fe chelating capacity exceeding 1.35 g/L. This desulfurization technology which has practical application prospect is currently in the phase of commercial scale-up study.
文摘The corrosion behavior of spheroidal graphite and flake graphite cast irons was studied in oxidizing and sulfidizing atmospheres between 600 and 800℃ for 50 h. The corrosion rate in the sulfidizing atmosphere was faster than that in air above 700℃, due to the formation of the Fe0.975S sulfide. The corrosion rate of the spheroidal graphite cast iron was similar to that of the flake graphite cast iron.
基金Project(07JJ6020) supported by the Hunan Provincial Natural Science Foundation of ChinaProject(2007-24-3) supported by the Huaihua Key Science and Technology Program, China
文摘Iron(Ⅱ) tetrasulfophthalocyanine(FeTSPc) ,as a novel mimetic enzyme of peroxidase,was used in the synthesis of a conducting polyaniline(PANI) /sodium dodecylsulfate(SDS) complex in SDS aqueous micellar solutions. The effects of pH,concentrations of aniline,SDS and H2O2,and reaction time on polymerization of aniline were studied in this case as shown by UV-Vis absorption spectroscopy. The results show that a wide range of pH(0.5-4.0) is required to produce the conducting PANI,and the optimal pH is 1.0 in SDS micelle. The optimal concentrations of aniline,SDS and H2O2 in feed,and reaction time in this case for the production of conducting PANI are respectively 10 mmol/L,10 mmol/L,25 mmol/L,and 15 h. FT-IR spectrum,elemental analysis,conductivity,cyclic voltammetry and thermogravimetric analysis confirm the thermal stability and electroactive form of PANI.
基金Supported by Open Project of Key Laboratory for Magnetism and Magnetic Materials of the Ministry of Education, Lanzhou University (MMM 200822)
文摘A coordination polymer based on iron（II） carboxylate helical chains [Fe（bpdc）（H2O）2]n 1 has been constructed hydrothermally using H2bpdc （H2bpdc = 2,2＇-bipyridine-4,4＇-dicarboxylic acid）, pyridine and FeSO4·7H2O. Its crystal structure reveals that the Fe（Ⅱ） ion adopts a slightly distorted octahedron. The carboxylates of bpdc ligands alternately bridge the Fe（Ⅱ） cations to form 1D infinite helical chains. The Fe···Fe intrachain distance is 4.8246（6） . The adjacent chains are further interlinked by the coordination of bpdc ligands and hydrogen bonding to form a 3D framework. Magnetic studies for complex 1 show weak antiferromagnetic coupling between the Fe（Ⅱ） ions. The best-fit for χM T vs. T with a Hamiltonian∑∑==iBiiHJSi SigHS11 leadsto g = 2.314（4） and J = –0.68（1） cm-1.
基金supported by the Scientific Research Start-up Funds of Shangrao Normal Universitythe Fourth Characteristic Specialty Foundation of University from Ministry of Education(TS11524)the Natural Science Foundation of Jiangxi Province(No.20122BAB203002)
文摘An iron（Ⅱ） coordination polymer, [Fe（Haip）2（H2O）2]n （1, Haip = 5-ammoniumiso- phthalato）, has been hydro/solvothermally synthesized and characterized by single-crystal X-ray diffraction, elemental analysis, infrared spectrum and magnetic measurement. Compound 1 crystalizes in monoclinic, space group P2/c with a = 6.9874（14）, b = 9.960（2）, c = 12.894（4） A, β = 117.47（2）°, Fe（C8H6NO4）2（H2O）2, Mr = 452.16, V= 796.2（3） A3, Z = 2, Dc = 1.886 g.cm-3, p = 1.017 mm-1, F（000） = 464.0, 2.71〈0〈28.42°, R = 0.0307, wR = 0.0840 and S = 1.005. Single-crystal X-ray diffraction analysis reveals that 1 features an infinite one-dimensional loop-like chain structure and Haip ligand in 1 is of zwitterionic form. Magnetic measurement results show the dominated ferromagnetic interactions among Fe11 atoms.
基金financailly supported by the National Natural Science Foundation of China (Nos.52275198 and 51805292)the Beijing Natural Science Foundation,China(No.2202020)the Tribology Science Fund of State Key Laboratory of Tribology,China (No.SKLT2022B11)。
文摘Fe–S compounds with hexagonal crystal structure are potential hydrogen permeation barrier during H2S corrosion. Hexagonal system Fe–S films were prepared on carbon steel through corrosion and CVD deposition, and the barrier effect of different Fe–S films on hydrogen permeation was tested using electrochemical hydrogen permeation method. After that, the electrical properties of Fe–S compound during phase transformation were measured using thermoelectric measurement system. Results show that the mackinawite has no obvious barrier effect on hydrogen penetration, as a p-type semiconductor, and pyrrhotite (including troilite) has obvious barrier effect on hydrogen penetration,as an n-type semiconductor. Hydrogen permeation tests showed peak permeation performance when the surface was deposited with a continuous film of pyrrhotite (Fe_(1–x)S) and troilite. The FeS compounds suppressed hydrogen permeation by the promotion of the hydrogen evolution reaction, semiconducting inversion from p-to n-type, and the migration of ions at the interface.
基金Funded by Chinese National Natural Science Foundation (No. 29904005), Key Foundation (No. 50038010) and Open Foundation from State Key Lab.of Advanced Technology for Materials Synthesis and Processing.
文摘Cobalt-phthalocyanine/iron nanocomposite particles have been obtained using method of composite in situ, with the mixture of carbonyl iron and solution of cobalt ( Ⅱ ) - phthalocyanine (Co-Pc) ultrasonic dispersing in N,N-dimethyl-formamide (DMF). Structure characterization of their inner and surface have relation with method of carbonyl iron joined in the mixture, contents of carbonyl iron and Co-Pc in the mixture of Co-Pc ultrasonic dispersing in DMF. With a method of composite in situ controlling reasonable experiment condition, it can be obtained that cobalt-phthalocyanine/iron nanocomposite particles has completely been covered with Co-Pc, they had structure of Chinese gooseberry in inner and mere made up of almost regular spherical shape and the average diameter is 1. 4 μm.
基金Chinese National Natural Science Foundation (No. 29674021) Hubei Natural Science Foundation(NO. 97J086).
文摘Magnetorheological suspension based on 20 (v/V) % CoPc-iron composite particles dispersed in sili-cone oil have been obtained, which exhibited dynamic shear stress up to 2000Pa upon application of external magnetic field at 1300 Oe. The response is faster than 0. 15 -with superior reversibility of changes in viscosity induced by external magnetic field at above 12. 5℃. Further, it was found that the MR fluid is in possession of long-term stability a-gainst sedimentation.
