Carbon Monoxide Modulates Auxin Transport and Nitric Oxide Signaling in Plants under Iron Deficiency Stress

Carbon monoxide(CO)and nitric oxide(NO)are signal molecules that enhance plant adaptation to environmental stimuli.Auxin is an essential phytohormone for plant growth and development.CO and NO play crucial roles in modulating the plant’s response to iron deficiency.Iron deficiency leads to an increase in the activity of heme oxygenase(HO)and the subsequent generation of CO.Additionally,it alters the polar subcellular distribution of Pin-Formed 1(PIN1)proteins,resulting in enhanced auxin transport.This alteration,in turn,leads to an increase in NO accumulation.Furthermore,iron deficiency enhances the activity of ferric chelate reductase(FCR),as well as the expression of the Fer-like iron deficiency-induced transcription factor 1(FIT)and the ferric reduction oxidase 2(FRO2)genes in plant roots.Overexpression of the long hypocotyl 1(HY1)gene,which encodes heme oxygenase,or the CO donor treatment resulted in enhanced basipetal auxin transport,higher FCR activity,and the expression of FIT and FRO2 genes under Fe deficiency.Here,a potential mechanism is proposed:CO and NO interact with auxin to address iron deficiency stress.CO alters auxin transport,enhancing its accumulation in roots and up-regulating key iron-related genes like FRO2 and IRT1.Elevated auxin levels affect NO signaling,leading to greater sensitivity in root development.This interplay promotes FCR activity,which is crucial for iron absorption.Together,these molecules enhance iron uptake and root growth,revealing a novel aspect of plant physiology in adapting to environmental stress.

Preparation of PrFe_(x)Co_(1-x)O_(3)/Mt catalyst and study on degradation of 2-hydroxybenzoic acid wastewater by catalytic wet peroxide oxidation

In this study,the perovskite nanocomposite PrFe_(x)Co_(1-x)O_(3)(Pr(S))was successfully synthesized by the sol-gel method;PrFe_(x)Co_(1-x)O_(3)/Al-pillared montmorillonite(Pr(S)/Mt)catalysts were prepared by impregnation(D)method and solid-melting(G)method,respectively,with Pr(S)as the active component and Al-pillared montmorillonite as the carrier.The catalysts were applied to treat the 2-hydroxybenzoic acid(2-HA)-simulated wastewater by catalytic wet peroxide oxidation(CWPO)technique,and the chemical oxygen demand(COD)removal rate and the 2-HA degradation rate were used as indicators to evaluate the catalytic performance.The results of the experiment indicated that the solid-melting method was more conducive to preparing the catalyst when the Co/Fe molar ratio of 7:3 and the optimal structural properties of the catalysts were achieved.The influence of operating parameters,including reaction temperature,catalyst dosage,H_(2)O_(2)dosage,pH,and initial 2-HA concentration,were optimized for the degradation of 2-HA by CWPO.The results showed that 97.64%of 2-HA degradation and 75.23%of COD removal rate were achieved under more suitable experimental conditions.In addition,after the catalyst was used five times,the degradation rate of 2-HA could still reach 76.93%,which implied the high stability and reusability of the catalyst.The high catalytic activity of the catalyst was due to the doping of Co into PrFeO_(3),which could promote the generation of HO·,and the high stability could be attributed to the loading of Pr(S)onto Al-Mt,which reduced the leaching of reactive metals.The study of reaction mechanism and kinetics showed that the whole degradation process conformed to the pseudo-firstorder kinetic equation,and the Langmuir-Hinshelwood method was applied to demonstrate that catalysis was dominant in the degradation process.

A critical review towards the causes of the iron-based catalysts deactivation mechanisms in the selective oxidation of hydrogen sulfide to elemental sulfur from biogas

Hydrogen sulfide(H_(2)S) not only presents significant environmental concerns but also induces severe corrosion in industrial equipment,even at low concentrations.Among various technologies,the selective oxidation of hydrogen sulfide(SOH_(2)S) to elemental sulfur(S) has emerged as a sustainable and environmentally friendly solution.Due to its unique properties,iron oxide has been extensively investigated as a catalyst for SOH_(2)S;however,rapid deactivation has remained a significant drawback.The causes of iron oxide-based catalysts deactivation mechanisms in SOH_(2)S,including sulfur or sulfate deposition,the transformation of iron species,sintering and excessive oxygen vacancy formation,and active site loss,are thoroughly examined in this review.By focusing on the deactivation mechanisms,this review aims to provide valuable insights into enhancing the stability and efficiency of iron-based catalysts for SOH_(2)S.

Efficient degradation of dye pollutants in wastewater via photocatalysis using a magnetic zinc oxide/graphene/iron oxide-based catalyst

In this paper, we present a proof-of-concept study of the enhancement of photocatalytic activity via a combined strategy of fabricating a visible-light responsive ternary heterostructure and improving overall photostability by incorporating magnetic zinc oxide/graphene/iron oxide (ZGF). A solvothermal approach was used to synthesize the catalyst. X-ray diffraction (XRD), scanning electron microscopic, energy dispersive X-ray, transmission electron microscopic, vibrating sample magnetometric, and ultraviolet–visible diffuse reflectance spectroscopic techniques were used to characterize the synthesized samples. The obtained optimal Zn(NO_(3))_(2) concentration, temperature, and heating duration were 0.10 mol/L, 600℃, and 1 h, respectively. The XRD pattern revealed the presence of peaks corresponding to zinc oxide, graphene, and iron oxide, indicating that the ZGF catalyst was effectively synthesized. Furthermore, when the developed ZGF was used for methylene blue dye degradation, the optimum irradiation time, dye concentration, catalyst dosage, irradiation intensity, and solution pH were 90 min, 10 mg/L, 0.03 g/L, 100 W, and 8.0, respectively. Therefore, the synthesized ZGF system could be used as a catalyst to degrade dyes in wastewater samples. This hybrid nanocomposite consisting of zinc oxide, graphene, and iron oxide could also be used as an effective photocatalytic degrader for various dye pollutants.

An amorphous manganese iron oxide hollow nanocube cathode for aqueous zinc ion batteries

Aqueous zinc ion batteries(ZIBs) are attracting considerable attentions for practical energy storage because of their low cost and high safety.Nevertheless,the traditional manganese oxide cathode materials suffer from the low intrinsic electronic conductivity,sluggish ions diffusion kinetics,and structural collapse,hindering their large-scale application.Herein,we successfully developed a latent amorphous Mn_(1.8)Fe_(1.2)O_(4) hollow nanocube(a-H-MnFeO) cathode material derived from Prussian blue analogue precursor.The amorphous nature endows the cathode with lower diffusion barrier and narrower band gap compared with crystalline counterpart,resulting in the superior Zn^(2+) ions and electrons transport kinetics.Hollow structure can furnish abundant surface sites and suppress the structural collapse during the repeated charge/discharge processes.By virtue of the multiple advantageous features,the a-H-MnFeO cathode exhibits exceptional electrochemical performance,in terms of high capacity,excellent rate capability,and prolonged cycle life.This strategy will pave the way for the structural design of emerging cathode materials.

Recent Progress in Superparamagnetic Iron Oxide Nanoparticles

Superparamagnetic iron oxide nanoparticles(SPIONs)have immeasurable potentials in many fields such as nanobiotechnology and biomedical engineering because of their superparamagnetic properties and small particle size.This review introduces the methods for SPIONs synthesis,including co-precipitation,thermal decomposition,microemulsion and hydrothermal reaction,and surface modification of SPIONs with organometallic and inorganic metals,surface modification for targeted drug delivery,and the use of SPIONs as a contrast agent.In addition,this article also provides an overview of recent progress in SPIONs for the treatment of glioma,lung cancer and breast cancer.

The assembly of a composite based on nano-sheet graphene oxide and montmorillonite

Graphene oxide （GO） nano-sheets were synthesized using a modified Hummers＇ method from graphite powder. The Raman spectrum of GO displayed a D-band at 1359 cm-1 and a G-band at 1594 cm-l. The ID/IG value of GO was calculated to be 0.97, suggesting the formation of new sp2 clusters upon reduction. A method was designed to investigate the assembly of the GO/montmorillonite （MMT） composite. After the addition of GO, the typical peaks of montmorillonite in FT-IR spectra shifted, indicating the assembly between GO and MMT. The D-band and G-band reduced sharply in the GO/MMT composite. More importantly, the D-band （1344 cm-1） and G-band （1574 cm 1） shifted significantly and the ID/ IG value of the GO/MMT composite was calculated to be 1.13, showing a change in the GO structure. In the addition of 0.04 wt% GO to MMT, the value of interlayer space （d） was up to 13.0 Ameasured by XRD due to the insertion of GO into MMT. The evident increases in contents of carbon atoms （26.59%） and nitrogen atoms （3.44%） indicate that GO was successfully combined with MMT. The nano-pores and clay sheets were not observed in the SEM image of GO/clay, but obvious wrinkles, while flexible sheets were observed in the typical scanning electron microscopy images of GO. This further proves that GO was combining with clay. The TEM image shows that the GO nano-sheets were tiled on the surface of MMT sheets. This observation suggests that a stable assembly structure was formed between GO sheets and MMT sheets. The change in particle size of MMT with the addition of GO shows that interaction occurred between GO sheets and MMT sheets, which was further confirmed by the results of zeta potential. Adsorption and insertion were the main mechanisms to assemble GO and MMT.

Synthesis of zinc oxide–montmorillonite composite and its effect on the removal of aqueous lead ions

Lead adsorption of zinc oxide-coated ACOR montmorillonite was investigated in batches and under reducing conditions at ambient temperature. The presence of zinc oxide coating significantly enhanced the adsorption of Pb^(2+) ions by ACOR montmorillonite. Characterization of adsorbents involved the use of X-ray diffraction, sodium saturation techniques, coulter laser analysis, scanning electron microscopy, and electron dispersive spectroscopy.Synthesis involved the trimetric process, activation of the ACOR montmorillonite and reacting of the same with zinc nitrate to produce a zinc oxide composite solid at 450 °C.The reaction mechanism indicated less than one proton coefficient, and higher mass transfer rates, when compared with bare montmorillonite. Intraparticle diffusion was higher than the value recorded for the bare montmorillonite. Reactions based on initial Pb^(2+) concentration indicated that coated montmorillonite gradually became saturated as the concentration was increased. Reactions based on solid concentration demonstrated a complex change in the capacity of adsorption over different Pb^(2+) concentrations(10–40 mg L^(-1)) and solid concentrations(2–10 g L^(-1)). The specific surface area reduction, particle size increase, mineral aggregation, and concentration gradient effect controlled the complex changes in adsorption.

Synthesis of a copper(Ⅱ) oxide–montmorillonite composite for lead removal

The synthesis of a copper(II) oxide–montmorillonite composite and its application in the removal of lead(II) ions in solution were investigated. The Acros Organics (ACOR) montmorillonite was activated using potassium hydroxide solution. The activated ACOR montmorillonite was titrated with copper(II) nitrate solution to produce the copper(II) oxide–montmorillonite composite. Adsorption experiments were conducted using batch-mode techniques under reducing conditions at ambient temperature. The reaction mechanism indicated a higher proton coefficient, greater intraparticle diffusion, and higher mass transfer rates compared with those achieved with bare montmorillonite. The intraparticle diffusion constant derived from the slope was 2.93^-3 (mg·g^–1·min^–0.5), and the intercept C was 9.86,≠ 0. In the presence of a CuO coating, the adsorption efficiency was 85.55% at pH 4 and 89.62% at pH 7. Therefore, the copper(II) oxide-montmorillonite composite, as a novel adsorbent with a very high adsorption capacity, exhibited substantially enhanced adsorption of Pb^2+ ions compared with bare montmorillonite.

Vicious cycle of lipid peroxidation and iron accumulation in neurodegeneration

Lipid peroxidation and iron accumulation are closely associated with neurodegenerative diseases,such as Alzheimer’s,Parkinson’s,and Huntington’s diseases,or neurodegeneration with brain iron accumulation disorders.Mitochondrial dysfunction,lipofuscin accumulation,autophagy disruption,and ferroptosis have been implicated as the critical pathomechanisms of lipid peroxidation and iron accumulation in these disorders.Currently,the connection between lipid peroxidation and iron accumulation and the initial cause or consequence in neurodegeneration processes is unclear.In this review,we have compiled the known mechanisms by which lipid peroxidation triggers iron accumulation and lipofuscin formation,and the effect of iron overload on lipid peroxidation and cellular function.The vicious cycle established between both pathological alterations may lead to the development of neurodegeneration.Therefore,the investigation of these mechanisms is essential for exploring therapeutic strategies to restrict neurodegeneration.In addition,we discuss the interplay between lipid peroxidation and iron accumulation in neurodegeneration,particularly in PLA2G6-associated neurodegeneration,a rare neurodegenerative disease with autosomal recessive inheritance,which belongs to the group of neurodegeneration with brain iron accumulation disorders.

Effect of competing solutes on arsenic(Ⅴ) adsorption using iron and aluminum oxides

The study focused on the effect of several typical competing solutes on removal of arsenic with Fe2O3 and Al2O3. The test results indicate that chloride, nitrate and sulfate did not have detectable effects, and that selenium（Ⅳ） （Se（Ⅳ）） and vanadium（Ⅴ） （V（Ⅴ）） showed slight effects on the adsorption of As（Ⅴ） with Fe2O3. The results also showed that adsorption of As（Ⅴ） on A12O3 was not affected by chloride and nitrate anions, but slightly by Se（Ⅳ） and V（Ⅴ） ions. Unlike the adsorption of As（Ⅴ） with Fe2O3, that with Fe2O3 was affected by the presence of sulfate in water solutions. Both phosphate and silica have significant adverse effects on the adsorption of As（Ⅴ） adsorption with Fe2O3 and Al2O3. Compared to the other tested anions, phosphate anion was found to be the most prominent solute affecting the As（Ⅴ） adsorption with Fe2O3 and Al2O3. In general, Fe2O3 has a better performance than Al2O3 in removal of As（Ⅴ） within a water environment where multi competing solutes are present.

Mutual effects of nitric oxide and iron on the growth of marine algae

Experiments on the effects of nitric oxide （NO） and iron on the growth of marine microalgae Skeletonema costatum were conducted. The results are as follows： exogenous NO could increase the growth rate of marine algae and raise the biomass remarkably under iron-deficient conditions. But it was a complicated process that the phytoplankton growth was influenced by NO and iron, which was controlled by the NO concentration, the nutrition level of the culture medium and the iron concentration, etc. Meanwhile, the iron concentration in the medium also has a direct influence on the growth and NO release capacity of the algae. Therefore, the effects of NO and iron on the growth of marine phytoplankton were mutual.

Selective catalytic oxidation of NO over iron and manganese oxides supported on mesoporous silica

The selective catalytic oxidation （SCO） of NO was studied on a catalyst consisting of iron-manganese oxide supported on mesoporous silica （MPS） with different Mn/Fe ratios. Effects of the amount of manganese and iron, oxygen, and calcination temperature on NO conversion were also investigated. It was found that the Mn-Fe/MPS catalyst with a Mn/Fe molar ratio of 1 showed the highest activity at the calcination temperature of 400 °C. The results showed that over this catalyst, NO conversion reached 70% under the condition of 280 °C and a space velocity of 5000 h-1. SO2 and H2O had no adverse impact on the reaction activity when the SCO reaction temperature was above 240 °C. In addition, the SCO activity was suppressed gradually in the presence of SO2 and H2O below 240 °C, and such an effect was reversible after heating treatment.

Extractive oxidative desulfurization of model oil/crude oil using KSF montmorillonite-supported 12-tungstophosphoric acid

12-Tungstophosphoric acid（PW） supported on KSF montmorillonite, PW/KSF, was used as catalyst for deep oxidative desulfurization（ODS） of mixed thiophenic compounds in model oil and crude oil under mild conditions using hydrogen peroxide（H2O2） as an oxidizing agent. A one-factor-at-a-time method was applied for optimizing the parameters such as temperature, reaction time, amount of catalyst, type of extractant and oxidant-tosulfur compounds（S-compounds） molar ratio. The corresponding products can be easily removed from the model oil by using ethanol as the best extractant. The results showed high catalytic activity of PW/KSF in the oxidative removal of dibenzothiophene（DBT） and mixed thiophenic model oil under atmospheric pressure at 75 ℃ in a biphasic system. To investigate the oxidation and adsorption effects of crude oil composition on ODS, the effects of cyclohexene, 1,7-octadiene and o-xylene with different concentrations were studied.

Characterization of Iron Oxide Generated in Ruthner Plant of Pickling Unit in Mobarakeh Steel Complex

Reducing the chloride content in regenerated iron oxides (RIO) from steel-pickling acid waste economically treated by Ruthner process is the most critical issue for the development of RIO as a useful raw material resource. In this paper, the results of a new method for characterization and modification of RIO produced in Mobarakeh Steel Complex were reported.

Ceramsite Containing Iron Oxide and its Use as Functional Aggregate in Microwave Absorbing Cement-based Materials

Electromagnetic（EM） wave absorbing cement-based composite has promising applications in protecting civil and military buildings from electromagnetic interferences. A new idea of preparing EM wave absorbing cement-based composite is proposed by using ceramsite containing iron oxide as EM wave absorbing functional aggregate. The ceramsite was synthesized by adding 10 wt% Fe3O4 into clay and sintering at 1 200 ℃, which shows obvious dielectric and magnetic loss properties for electromagnetic wave. The maximum reflection loss（RL） of the concrete specimens prepared with the ceramsite is between-10.2--10.7 dB（corresponding to absorption greater than 90% EM energy） in the bandwidth of 8-18 GHz. In addition, the compressive strength at 28 days age of the concrete is 46 MPa, showing the potentiality of being used as structural components in buildings.

The production of iron oxide during peridotite serpentinization:Influence of pyroxene

Serpentinization produces molecular hydrogen(H2)that can support communities of microorganisms in hydrothermal fields;H2 results from the oxidation of ferrous iron in olivine and pyroxene into ferric iron,and consequently iron oxide(magnetite or hematite)forms.However,the mechanisms that control H2 and iron oxide formation are poorly constrained.In this study,we performed serpentinization experiments at 311℃ and 3.0 kbar on olivine(with <5% pyroxene),orthopyroxene,and peridotite.The results show that serpentine and iron oxide formed when olivine and orthopyroxene individually reacted with a saline starting solution.Olivine-derived serpentine had a significantly lower FeO content(6.57±1.30 wt.%)than primary olivine(9.86 wt.%),whereas orthopyroxene-derived serpentine had a comparable FeO content(6.26±0.58 wt.%)to that of primary orthopyroxene(6.24 wt.%).In experiments on peridotite,olivine was replaced by serpentine and iron oxide.However,pyroxene transformed solely to serpentine.After 20 days,olivine-derived serpentine had a FeO content of 8.18±1.56 wt.%,which was significantly higher than that of serpentine produced in olivine-only experiments.By contrast,serpentine after orthopyroxene had a slightly higher FeO content(6.53±1.01 wt.%)than primary orthopyroxene.Clinopyroxene-derived serpentine contained a significantly higher FeO content than its parent mineral.After 120 days,the FeO content of olivine-derived serpentine decreased significantly(5.71±0.35 wt.%),whereas the FeO content of orthopyroxene-derived serpentine increased(6.85±0.63 wt.%)over the same period.This suggests that iron oxide preferentially formed after olivine serpentinization.Pyroxene in peridotite gained some Fe from olivine during the serpentinization process,which may have led to a decrease in iron oxide production.The correlation between FeO content and SiO_2 or AI_2 O_3 content in olivine-and orthopyroxene-derived serpentine indicates that aluminum and silica greatly control the production of iron oxide.Based on our results and data from natural serpentinites reported by other workers,we propose that aluminum may be more influential at the early stages of peridotite serpentinization when the production of iron oxide is very low,whereas silica may have a greater control on iron oxide production during the late stages instead.

Effects of Catalyst and Additive Containing Li, Na, or Ca on Reduction of Iron Oxide/Carbon Composite Pellets

The catalyst containing 0.69% (mass fraction) of Li+, Na+, or Ca2+ were synthesized, and the catalytic effect on the reduction of iron oxide/carbon composite pellets were investigated by comparing with that of additive at 850 degreesC. The effect of the catalyst was greater than that of the additive, it can be considered that catalyst promoted the formation of iron nucleus early on reduction processes of iron oxide/carbon composite pellets. In addition, both effects of catalyst and additive increased after added carbon powder into the pellets, but the extent of increase decreased when the carbon powder exceeded a suitable content (about 4%), this amount is less than that of carbon needed theoretically on the reduction from hematite to iron.

Exogenous Nitric Oxide Alleviated the Inhibition of Photosynthesis and Antioxidant Enzyme Activities in Iron-Deficient Chinese Cabbage (Brassica chinensis L.)

The effects of exogenous nitric oxide （NO） on plant growth, chlorophyll contents, photosynthetic and chlorophyll fluorescence parameters as well as lipid peroxidation and activities of antioxidant enzymes were investigated in Chinese cabbage plants exposed to iron （Fe） deficiency. Iron deficiency led to serious chlorosis in Chinese cabbage leaves, and resulted in significant decrease in plant growth, photosynthetic pigments, net photosynthetic rate, Fv/Fm, Ф ps Ⅱ and activities of antioxidant enzymes, and increase in lipid peroxidation. While treatment with SNP, a NO donor, it could revert the iron deficiency symptoms, increased photosynthetic rate as well as activities of antioxidant enzymes, and protected membrane from lipid peroxidation, as a result, the growth inhibition of Chinese cabbage by Fe deficiency was alleviated.

Staged reaction kinetics and characteristics of iron oxide direct reduction by carbon

Staged reduction kinetics and characteristics of iron oxide direct reduction by carbon were studied in this work. The characteristics were investigated by simultaneous thermogravimetric analysis, X-ray diffraction（XRD）, and quadrupole mass spectrometry. The kinetics parameters of the reduction stages were obtained by isoconversional（model-free） methods. Three stages in the reduction are Fe2O3→Fe3O4, Fe3O4→Fe O, and Fe O→Fe, which start at 912 K, 1255 K, and 1397 K, respectively. The CO content in the evolved gas is lower than the CO2content in the Fe2O3→Fe3O4stage but is substantially greater than the CO2 contents in the Fe3O4→Fe O and Fe O→Fe stages, where gasification starts at approximately 1205 K. The activation energy（E） of the three stages are 126–309 k J/mol, 628 k J/mol, and 648 k J/mol, respectively. The restrictive step of the total reduction is Fe O→Fe. If the rate of the total reduction is to be improved, the rate of the Fe O→Fe reduction should be improved first. The activation energy of the first stage is much lower than those of the latter two stages because of carbon gasification. Carbon gasification and FexOy reduction by CO, which are the restrictive step in the last two stages, require further study.