The shear behavior is regarded as the dominant property of rock joints and is dramatically affected by the joint surface roughness.To date,the effect of surface roughness on the shear behavior of rock joints under sta...The shear behavior is regarded as the dominant property of rock joints and is dramatically affected by the joint surface roughness.To date,the effect of surface roughness on the shear behavior of rock joints under static or cyclic loading conditions has been extensively studied,but such effect under impact loading conditions keeps unclear.To address this issue,a series of impact shear tests was performed using a novel-designed dynamic experimental system combined with the digital image correlation(DIC)technique.The dynamic shear strength,deformability and failure mode of the jointed specimens with various joint roughness coefficients(JRC)are comprehensively analyzed.Results show that the shear strength and shear displacement characteristics of the rock joint under the impact loading keep consistent with those under static loading conditions.However,the temporal variations of shear stress,slip displacement and normal displacement under the impact loading conditions show obviously different behaviors.An elastic rebound of the slip displacement occurs during the impact shearing and its value increases with increasing joint roughness.Two identifiable stages(i.e.compression and dilation)are observed in the normal displacement curves for the rougher rock joints,whereas the joints with small roughness only manifest normal compression displacement.Besides,as the roughness increases,the maximum compression tends to decrease,while the maximum dilation gradually increases.More-over,the microstructural analysis based on scanning electron microscope(SEM)suggests that the roughness significantly affects the characteristics of the shear fractured zone enclosing the joint surface.展开更多
Jointed rock specimens with a natural replicated joint surface oriented at a mean dip angle of 60were prepared,and a series of cyclic triaxial tests was performed at different confining pressures and cyclic deviatoric...Jointed rock specimens with a natural replicated joint surface oriented at a mean dip angle of 60were prepared,and a series of cyclic triaxial tests was performed at different confining pressures and cyclic deviatoric stress amplitudes.The samples were subjected to 10,000 loading-unloading cycles with a frequency of 8 Hz.At each level of confining pressure,the applied cyclic deviatoric stress amplitude was increased incrementally until excessive deformation of the jointed rock specimen was observed.Analysis of the test results indicated that there existed a critical cyclic deviatoric stress amplitude(i.e.critical dynamic deviatoric stress)beyond which the jointed rock specimens yielded.The measured critical dynamic deviatoric stress was less than the corresponding static deviatoric stress.At cyclic deviatoric stress amplitudes less than the critical dynamic deviatoric stress,minor cumulative residual axial strains were observed,resulting in hysteretic damping.However,for cyclic deviatoric stresses beyond the critical dynamic deviatoric stress,the plastic strains increased promptly,and the resilient moduli degraded rapidly during the initial loading cycles.Cyclic triaxial test results showed that at higher confining pressures,the ultimate residual axial strain attained by the jointed rock specimen decreased,the steadystate dissipated energy density and steady-state damping ratio per load cycle decreased,while steadystate resilient moduli increased.展开更多
Joint deformity and dysfunction are common and serious complications in the late stage of rheumatoid arthritis,which seriously affect the quality of life of patients.Traditional Chinese medicine(TCM)believes that join...Joint deformity and dysfunction are common and serious complications in the late stage of rheumatoid arthritis,which seriously affect the quality of life of patients.Traditional Chinese medicine(TCM)believes that joint deformity and dysfunction in some patients with rheumatoid arthritis are closely related to the apraxia of meridians and tendons due to enduring illness.Based on the theory of meridians and tendons circulation,using the local and nearby therapeutic effect of acupoints as the treatment method in clinical practice,we conducted penetration needling of Houxi,Baxie,Wailaogong as well as Ashi points of interphalangeal joints of both hands through bilateral Sanjian,and used the uniform reinforcing-reducing method to soothe tendons and meridians,thus effectively improving the dysfunction of deformed joints.展开更多
基金We acknowledge the funding support from the National Natural Science Foundation of China(Grant Nos.51879135 and 51879184)the Natural Sciences and Engineering Research Council of Canada(NSERC)through the Discovery Grant No.72031326.
文摘The shear behavior is regarded as the dominant property of rock joints and is dramatically affected by the joint surface roughness.To date,the effect of surface roughness on the shear behavior of rock joints under static or cyclic loading conditions has been extensively studied,but such effect under impact loading conditions keeps unclear.To address this issue,a series of impact shear tests was performed using a novel-designed dynamic experimental system combined with the digital image correlation(DIC)technique.The dynamic shear strength,deformability and failure mode of the jointed specimens with various joint roughness coefficients(JRC)are comprehensively analyzed.Results show that the shear strength and shear displacement characteristics of the rock joint under the impact loading keep consistent with those under static loading conditions.However,the temporal variations of shear stress,slip displacement and normal displacement under the impact loading conditions show obviously different behaviors.An elastic rebound of the slip displacement occurs during the impact shearing and its value increases with increasing joint roughness.Two identifiable stages(i.e.compression and dilation)are observed in the normal displacement curves for the rougher rock joints,whereas the joints with small roughness only manifest normal compression displacement.Besides,as the roughness increases,the maximum compression tends to decrease,while the maximum dilation gradually increases.More-over,the microstructural analysis based on scanning electron microscope(SEM)suggests that the roughness significantly affects the characteristics of the shear fractured zone enclosing the joint surface.
文摘Jointed rock specimens with a natural replicated joint surface oriented at a mean dip angle of 60were prepared,and a series of cyclic triaxial tests was performed at different confining pressures and cyclic deviatoric stress amplitudes.The samples were subjected to 10,000 loading-unloading cycles with a frequency of 8 Hz.At each level of confining pressure,the applied cyclic deviatoric stress amplitude was increased incrementally until excessive deformation of the jointed rock specimen was observed.Analysis of the test results indicated that there existed a critical cyclic deviatoric stress amplitude(i.e.critical dynamic deviatoric stress)beyond which the jointed rock specimens yielded.The measured critical dynamic deviatoric stress was less than the corresponding static deviatoric stress.At cyclic deviatoric stress amplitudes less than the critical dynamic deviatoric stress,minor cumulative residual axial strains were observed,resulting in hysteretic damping.However,for cyclic deviatoric stresses beyond the critical dynamic deviatoric stress,the plastic strains increased promptly,and the resilient moduli degraded rapidly during the initial loading cycles.Cyclic triaxial test results showed that at higher confining pressures,the ultimate residual axial strain attained by the jointed rock specimen decreased,the steadystate dissipated energy density and steady-state damping ratio per load cycle decreased,while steadystate resilient moduli increased.
基金Supported by National Natural Science Foundation of China(82205105).
文摘Joint deformity and dysfunction are common and serious complications in the late stage of rheumatoid arthritis,which seriously affect the quality of life of patients.Traditional Chinese medicine(TCM)believes that joint deformity and dysfunction in some patients with rheumatoid arthritis are closely related to the apraxia of meridians and tendons due to enduring illness.Based on the theory of meridians and tendons circulation,using the local and nearby therapeutic effect of acupoints as the treatment method in clinical practice,we conducted penetration needling of Houxi,Baxie,Wailaogong as well as Ashi points of interphalangeal joints of both hands through bilateral Sanjian,and used the uniform reinforcing-reducing method to soothe tendons and meridians,thus effectively improving the dysfunction of deformed joints.
