Self-assembled S-scheme In_(2.77)S_(4)/K^(+)-doped g-C_(3)N_(4)photocatalyst with selective O_(2) reduction pathway for efficient H_(2)O_(2) production using water and air

The development of an efficient artificial H_(2)O_(2) photosynthesis system is a challenging work using H_(2)O and O_(2) as starting materials.Herein,3D In_(2.77)S_(4) nanoflower precursor was in-situ deposited on K^(+)-doped g-C_(3)N_(4)(KCN)nanosheets using a solvothermal method,then In_(2.77)S_(4)/KCN(IS/KCN)het-erojunction with an intimate interface was obtained after a calcination process.The investigation shows that the photocatalytic H_(2)O_(2) production rate of 50IS/KCN can reach up to 1.36 mmol g^(-1)h^(-1)without any sacrificial reagents under visible light irradiation,which is 9.2 times and 4.1 times higher than that of KCN and In_(2.77)S_(4)/respectively.The enhanced activity of the above composite can be mainly attributed to the S-scheme charge transfer route between KCN and In_(2.77)S_(4) according to density functional theory calculations,electron paramagnetic resonance and free radical capture tests,leading to an expanded light response range and rapid charge separation at their interface,as well as preserving the active electrons and holes for H_(2)O_(2) production.Besides,the unique 3D nanostructure and surface hydrophobicity of IS/KCN facilitate the diffusion and transportation of O_(2) around the active centers,the energy barriers of O_(2) protonation and H_(2)O_(2) desorption steps are ef-fectively reduced over the composite.In addition,this system also exhibits excellent light harvesting ability and stability.This work provides a potential strategy to explore a sustainable H_(2)O_(2) photo-synthesis pathway through the design of heterojunctions with intimate interfaces and desired reac-tion thermodynamics and kinetics.

低盐水体Na^(+)/K^(+)对凡纳滨对虾生长、体成分与肝胰腺、鳃组织结构的影响

缺钾在内陆低盐度盐碱水中经常发生,为探究低盐水体中不同钾缺乏程度对凡纳滨对虾生长、存活、体成分以及鳃和肝胰腺组织结构的影响,实验参照海水离子组成配置盐度为2的低盐度水体,在Na^(+)/K^(+)(mg/mg)比值为27、47、67、87、107 (分别记为A、B、C、D、E组)的条件下,对体重为(1.04±0.23) g的凡纳滨对虾幼虾开展了为期60 d的养殖实验。结果显示,E组对虾的存活率为44.64%±20.95%,显著低于A、B、D三组;E组体重为(4.86±0.66) g,显著低于其他4组;A~D组之间的湿重、增重率、特定生长率差异不显著,但均大于E组且差异显著;在饲料系数上,E组最高并与A、D组差异显著。在体成分上,各组全虾钾含量、灰分含量差异不显著,E组的水分含量高于其他组,并与A、B组差异显著;E组粗蛋白含量最低,且与B组差异显著。E组对虾鳃组织角质层明显受损,红细胞数量减少,空泡增多,肝胰腺B细胞及其内部转运泡体积增大,肝小管结构受损。研究表明,低盐条件下严重缺钾引起了对虾鳃和肝胰腺损伤,降低了对虾的存活率和生长率;水体缺钾在前期即可对对虾的生长产生明显影响,而对存活的影响随养殖时间的增加而增大。实验结果有助于为内陆低盐度盐碱水养殖凡纳滨对虾提供理论依据。

普通烟草外向整流Shaker K^(+)通道NtSKOR1的组织表达分析

外向整流Shaker K^(+)通道SKOR(Stelar K^(+)outward rectifier)是一类定位于植物根部中柱细胞质膜的外向整流Shaker K^(+)通道。为探究普通烟草NtSKOR1的启动子活性和不同时期组织表达情况,克隆该基因上游2439 bp的启动子序列,创制启动子驱动β-葡萄糖苷酸酶基因(GUS)的烟草材料并进行组织化学染色,通过RT-qPCR验证该基因的表达。结果表明NtSKOR1启动子含有光响应、逆境胁迫和激素等相关的顺式作用元件;转ProNtSKOR1::GUS烟草的组织化学染色试验表明:萌发期至子叶展平期未检测到GUS活性;小十字期,在真叶叶脉和茎尖分生组织开始检测到GUS活性;生根期,除茎和叶脉的维管组织外,在根部维管组织也开始检测到明显GUS活性,且活性随烟株生长而逐渐增强;盛花期,主要在烟草的根、茎和叶脉维管组织检测到活性,且上部叶叶脉中的GUS活性高于下部叶叶脉。RT-qPCR与GUS活性检测结果基本一致。综上可知,NtSKOR1主要在烟草小十字期及后续发育阶段的根、茎、叶的维管组织中表达,烟草进入盛花期后,该基因在光合作用较强的上部叶中的表达高于下部叶,推测该基因可能参与烟草K^(+)转运和同化产物协同运输。

K^(+)掺杂双钙钛矿Cs_(2)AgInCl_(6)的发光性质

采用固相球磨法制备了K^(+)掺杂双钙钛矿Cs_(2)AgInCl_(6)纳米材料,该方法无需配体辅助,绿色环保。通过X射线衍射和拉曼光谱对晶体结构进行研究,通过激发光谱、发射光谱和时间分辨光谱对其发光性能进行研究。结果表明,Cs_(2)AgInCl_(6)为立方晶体,属于Fm3m空间群,由于宇称禁戒跃迁,其荧光量子产率(PLQY)低,小于0.1%。低于60%的K^(+)掺杂主要取代Ag^(+)的位置,引起Cs_(2)AgInCl_(6)的晶格膨胀,消除了晶格结构的反演对称性,打破了宇称禁戒跃迁,掺杂后Cs_(2)AgInCl_(6)的光致发光强度显著增强。K^(+)的最佳掺杂比例为40%,Cs_(2)Ag_(0.6)K_(0.4)InCl_(6)材料发射中心波长为640 nm,半高宽为180 nm,平均荧光寿命达到29.2 ns,PLQY达到10.5%。当K^(+)掺杂比例超过60%,K^(+)开始取代Cs+的位置,产物发生相变,出现立方相的Cs_(2-x)K_(1+x+y)AgyInCl_(6)和单斜相的Cs_(2-x)K_(1+x)InCl_(6)产物,这些产物由于强电子-声子耦合,非辐射复合占据主导地位。

Na^(+)/K^(+)-ATPase:ion pump,signal transducer,or cytoprotective protein,and novel biological functions

Na^(+)/K^(+)-ATPase is a transmembrane protein that has important roles in the maintenance of electrochemical gradients across cell membranes by transporting three Na^(+)out of and two K^(+)into cells.Additionally,Na^(+)/K^(+)-ATPase participates in Ca^(2+)-signaling transduction and neurotransmitter release by coordinating the ion concentration gradient across the cell membrane.Na^(+)/K^(+)-ATPase works synergistically with multiple ion channels in the cell membrane to form a dynamic network of ion homeostatic regulation and affects cellular communication by regulating chemical signals and the ion balance among different types of cells.Therefo re,it is not surprising that Na^(+)/K^(+)-ATPase dysfunction has emerged as a risk factor for a variety of neurological diseases.However,published studies have so far only elucidated the important roles of Na^(+)/K^(+)-ATPase dysfunction in disease development,and we are lacking detailed mechanisms to clarify how Na^(+)/K^(+)-ATPase affects cell function.Our recent studies revealed that membrane loss of Na^(+)/K^(+)-ATPase is a key mechanism in many neurological disorders,particularly stroke and Parkinson's disease.Stabilization of plasma membrane Na^(+)/K^(+)-ATPase with an antibody is a novel strategy to treat these diseases.For this reason,Na^(+)/K^(+)-ATPase acts not only as a simple ion pump but also as a sensor/regulator or cytoprotective protein,participating in signal transduction such as neuronal autophagy and apoptosis,and glial cell migration.Thus,the present review attempts to summarize the novel biological functions of Na^(+)/K^(+)-ATPase and Na^(+)/K^(+)-ATPase-related pathogenesis.The potential for novel strategies to treat Na^(+)/K^(+)-ATPase-related brain diseases will also be discussed.

Enhancing the stability of Ni Fe-layered double hydroxide nanosheet array for alkaline seawater oxidation by Ce doping

Electrocatalytic hydrogen production from seawater holds enormous promise for clean energy generation.Nevertheless,the direct electrolysis of seawater encounters significant challenges due to poor anodic stability caused by detrimental chlorine chemistry.Herein,we present our recent discovery that the incorporation of Ce into Ni Fe layered double hydroxide nanosheet array on Ni foam(Ce-Ni Fe LDH/NF)emerges as a robust electrocatalyst for seawater oxidation.During the seawater oxidation process,CeO_(2)is generated,effectively repelling Cl^(-)and inhibiting the formation of Cl O-,resulting in a notable enhancement in the oxidation activity and stability of alkaline seawater.The prepared Ce-Ni Fe LDH/NF requires only overpotential of 390 m V to achieve the current density of 1 A cm^(-2),while maintaining long-term stability for 500 h,outperforming the performance of Ni Fe LDH/NF(430 m V,150 h)by a significant margin.This study highlights the effectiveness of a Ce-doping strategy in augmenting the activity and stability of materials based on Ni Fe LDH in seawater electrolysis for oxygen evolution.

Co-doped BaFe_(2)As_(2) Josephson junction fabricated with a focused helium ion beam

Josephson junction plays a key role not only in studying the basic physics of unconventional iron-based superconductors but also in realizing practical application of thin-film based devices,therefore the preparation of high-quality iron pnictide Josephson junctions is of great importance.In this work,we have successfully fabricated Josephson junctions from Co-doped BaFe_(2)As_(2)thin films using a direct junction fabrication technique which utilizes high energy focused helium ion beam(FHIB).The electrical transport properties were investigated for junctions fabricated with various He^(+)irradiation doses.The junctions show sharp superconducting transition around 24 K with a narrow transition width of 2.5 K,and a dose correlated foot-structure resistance which corresponds to the effective tuning of junction properties by He^(+)irradiation.Significant J_c suppression by more than two orders of magnitude can be achieved by increasing the He^(+)irradiation dose,which is advantageous for the realization of low noise ion pnictide thin film devices.Clear Shapiro steps are observed under 10 GHz microwave irradiation.The above results demonstrate the successful fabrication of high quality and controllable Co-doped BaFe_(2)As_(2)Josephson junction with high reproducibility using the FHIB technique,laying the foundation for future investigating the mechanism of iron-based superconductors,and also the further implementation in various superconducting electronic devices.

Enhanced conductivity and weakened magnetism in Pb-doped Sr_(2)IrO_(4)

Group IV element Pb has been selected as the dopant to dope at the Sr site of Sr_(2)IrO_(4). It is exciting to find that the single-phase crystal structure could be maintained with a high Pb doping level of up to x=0.3 in Sr_(2-x)Pb_(x)IrO_(4). The mapping data obtained from energy-dispersive x-ray spectroscopy analyses give solid evidence that the Pb ions are uniformly distributed in the Sr_(2)IrO_(4) matrix. The incorporation of Pb leads to a moderate depression of the canted antiferromagnetic ordering state. The electrical conductivity could be greatly enhanced when the Pb doping content is higher than x=0.2.The present results give a fresh material base to explore new physics in doped Sr_(2)IrO_(4) systems.

Hole-Doped Nonvolatile and Electrically Controllable Magnetism in van der Waals Ferroelectric Heterostructures

Electrical control of magnetism in van der Waals semiconductors is a promising step towards development of two-dimensional spintronic devices with ultralow power consumption for processing and storing information.Here, we propose a design for two-dimensional van der Waals heterostructures(vdWHs) that can host ferroelectricity and ferromagnetism simultaneously under hole doping. By contacting an In Se monolayer and forming an InSe/In_(2)Se_(3) vd WH, the switchable built-in electric field from the reversible out-of-plane polarization enables robust control of the band alignment. Furthermore, switching between the two ferroelectric states(P_↑ and P_↓)of hole-doped In_(2)Se_(3) with an external electric field can interchange the ON and OFF states of the nonvolatile magnetism. More interestingly, doping concentration and strain can effectively tune the magnetic moment and polarization energy. Therefore, this provides a platform for realizing multiferroics in ferroelectric heterostructures,showing great potential for use in nonvolatile memories and ferroelectric field-effect transistors.

Mott Gap Filling by Doping Electrons through Depositing One Sub-Monolayer Thin Film of Rb on Ca_(2)CuO_(2)Cl_(2)

Understanding the doping evolution from a Mott insulator to a superconductor probably holds the key to resolve the mystery of unconventional superconductivity in copper oxides. To elucidate the evolution of the electronic state starting from the Mott insulator, we dose the surface of the parent phase Ca_(2)CuO_(2)Cl_(2) by depositing Rb atoms, which are supposed to donate electrons to the CuO_(2) planes underneath. We successfully achieved the Rb sub-monolayer thin films in forming the square lattice. The scanning tunneling microscopy or spectroscopy measurements on the surface show that the Fermi energy is pinned within the Mott gap but close to the edge of the charge transfer band. In addition, an in-gap state appears at the bottom of the upper Hubbard band(UHB), and the Mott gap will be significantly diminished. Combined with the Cl defect and the Rb adatom/cluster results, the electron doping is likely to increase the spectra weight of the UHB for the double occupancy. Our results provide information to understand the electron doping to the parent compound of cuprates.

Enhancing multifunctional photocatalysis with acetate-assisted cesium doping and unlocking the potential of Z-scheme solar water splitting

Graphitic carbon nitride(g-C_(3)N_(4))has been extensively doped with alkali metals to enlarge photocatalytic output,in which cesium(Cs)doping is predicted to be the most efficient.Nevertheless,the sluggish diffusion and doping kinetics of precursors with high melting points,along with imprecise regulation,have raised the debate on whether Cs doping could make sense.For this matter,we attempt to confirm the positive effects of Cs doping on multifunctional photocatalysis by first using cesium acetate with the character of easy manipulation.The optimized Csdoped g-C_(3)N_(4)(CCN)shows a 41.6-fold increase in visible-light-driven hydrogen evolution reaction(HER)compared to pure g-C_(3)N_(4) and impressive degradation capability,especially with 77%refractory tetracycline and almost 100%rhodamine B degradedwithin an hour.The penetration ofCs+is demonstrated to be a mode of interlayer doping,and Cs–N bonds(especially with sp^(2) pyridine N in C═N–C),along with robust chemical interaction and electron exchange,are fabricated.This atomic configuration triggers the broadened spectral response,the improved charge migration,and the activated photocatalytic capacity.Furthermore,we evaluate the CCN/cadmium sulfide hybrid as a Z-scheme configuration,promoting the visible HER yield to 9.02 mmol g^(−1) h^(−1),which is the highest ever reported among all CCN systems.This work adds to the rapidly expanding field of manipulation strategies and supports further development of mediating served for photocatalysis.

Investigation on p-type doping of PBn unipolar barrier InAsSb photodetectors

The lattice-matched XBn structures of InAsSb,grown on GaSb substrates,exhibit high crystal quali⁃ty,and can achieve extremely low dark currents at high operating temperatures(HOT).Its superior performance is attributed to the unipolar barrier,which blocks the majority carriers while allowing unhindered hole transport.To further explore the energy band and carrier transport mechanisms of the XBn unipolar barrier structure,this pa⁃per systematically investigates the influence of doping on the dark current,photocurrent,and tunneling character⁃istics of InAsSb photodetectors in the PBn structure.Three high-quality InAsSb samples with unintentionally doped absorption layers(AL)were prepared,with varying p-type doping concentrations in the GaSb contact layer(CL)and the AlAsSb barrier layer(BL).As the p-type doping concentration in the CL increased,the device’s turn-on bias voltage also increased,and p-type doping in the BL led to tunneling occurring at lower bias voltages.For the sample with UID BL,which exhibited an extremely low dark current of 5×10^(-6) A/cm^(2).The photocurrent characteristics were well-fitted using the back-to-back diode model,revealing the presence of two opposing space charge regions on either side of the BL.

Neutral and metallic vs.charged and semiconducting surface layer in acceptor doped CeO_(2)

The monomolecular surface layer of acceptor doped CeO_(2) may become neutral and metallic or charged and semiconducting.This is revealed in the theoretical analysis of the oxygen pressure dependence of the surface defects concentration in acceptor doped ceria with two different dopant types and operated under different oxygen pressures.Recently published experimental data for highly reduced Sm0.2Ce0.8O1.9-x(SDC)containing a fixed valence dopant Sm3+are very different from those published for Pr0.1Ce0.9O_(2)-x(PCO) with the variable valence dopant Pr4+/Pr3+being reduced under milder conditions.The theoretical analysis of these experimental results fits very well the experimental results of SDC and PCO.It leads to the following predictions:the highly reduced surface of SDC is metallic and neutral,the metallic surface electron density of state is gs=0.9×10^(38)J-1·m^(-2)(1.4×1015eV^(-1)·cm^(-2)),the electron effective mass is meff,s=3.3me,and the phase diagram of the reduced surface has theα(fcc)structure as in the bulk.In PCO a double layer is predicted to be formed between the surface and the bulk with the surface being negatively charged and semiconducting.The surface of PCO maintains high Pr^(3+) defect concentration as well as relative high oxygen vacancy concentration at oxygen pressures higher than in the bulk.The reasons for the difference between a metallic and semiconducting surface layer of acceptor doped CeO_(2) are reviewed,as well as the key theoretical considerations applied in coping with this problem.For that we make use of the experimental data and theoretical analysis available for acceptor doped ceria.

Photodoping-Modified Charge Density Wave Phase Transition in WS_(2)/1T-TaS_(2) Heterostructure

Controlling collective electronic states hold great promise for development of innovative devices. Here, we experimentally detect the modification of the charge density wave(CDW) phase transition within a 1T-TaS_(2) layer in a WS_(2)/1T-TaS_(2) heterostructure using time-resolved ultrafast spectroscopy. Laser-induced charge transfer doping strongly suppresses the commensurate CDW phase, which results in a significant decrease in both the phase transition temperature(T_(c)) and phase transition stiffness. We interpret the phenomenon that photoinduced hole doping, when surpassing a critical threshold value of ~ 10^(18)cm^(-3), sharply decreases the phase transition energy barrier. Our results provide new insights into controlling the CDW phase transition, paving the way for optical-controlled novel devices based on CDW materials.

Pillar effect induced by ultrahigh phosphorous/nitrogen doping enables graphene/MXene film with excellent cycling stability for alkali metal ion storage

Graphene's large theoretical surface area and high conductivity make it an attractive anode material for potassium-ion batteries(PIBs).However,its practical application is hindered by small interlayer distance and long ion transfer distance.Herein,this paper aims to address the issue by introducing MXene through a simple and scalable method for assembling graphene and realizing ultrahigh P doping content.The findings reveal that MXene and P-C bonds have a "pillar effect" on the structure of graphene,and the P-C bond plays a primary role.In addition,N/P co-doping introduces abundant defects,providing more active sites for K^(+) storage and facilitating K^(+) adsorption.As expected,the developed ultrahigh phosphorous/nitrogen co-doped flexible reduced graphene oxide/MXene(NPrGM) electrode exhibits remarkable reversible discharge capacity(554 mA hg^(-1) at 0.05 A g^(-1)),impressive rate capability(178 mA h g^(-1) at 2 A g^(-1)),and robust cyclic stability(0.0005% decay per cycle after 10,000 cycles at 2 A g^(-1)).Furthermore,the assembled activated carbon‖NPrGM potassium-ion hybrid capacitor(PIHC) can deliver an impressive energy density of 131 W h kg^(-1) and stable cycling performance with 98.1% capacitance retention after5000 cycles at 1 A g^(-1).Such a new strategy will effectively promote the practical application of graphene materials in PIBs/PIHCs and open new avenues for the scalable development of flexible films based on two-dimensional materials for potential applications in energy storage,thermal interface,and electromagnetic shielding.

Progress in efficient doping of Al-rich AlGaN

The development of semiconductors is always accompanied by the progress in controllable doping techniques.Taking AlGaN-based ultraviolet(UV)emitters as an example,despite a peak wall-plug efficiency of 15.3%at the wavelength of 275 nm,there is still a huge gap in comparison with GaN-based visible light-emitting diodes(LEDs),mainly attributed to the inefficient doping of AlGaN with increase of the Al composition.First,p-doping of Al-rich AlGaN is a long-standing challenge and the low hole concentration seriously restricts the carrier injection efficiency.Although p-GaN cladding layers are widely adopted as a compromise,the high injection barrier of holes as well as the inevitable loss of light extraction cannot be neglected.While in terms of n-doping the main issue is the degradation of the electrical property when the Al composition exceeds 80%,resulting in a low electrical efficiency in sub-250 nm UV-LEDs.This review summarizes the recent advances and outlines the major challenges in the efficient doping of Al-rich AlGaN,meanwhile the corresponding approaches pursued to overcome the doping issues are discussed in detail.

Thermodynamic equilibrium theory-guided design and synthesis of Mg-doped LiFe_(0.4)Mn_(0.6)PO_(4)/C cathode for lithium-ion batteries

Mn-rich LiFe_(1-x)Mn_(x)PO_(4)(x>0.5),which combines the high operation voltage of LiMnPO_(4)with excellent rate performa nce of LiFePO4,is hindered by its sluggish kinetic properties.Herein,thermodynamic equilibrium analysis of Mn^(2+)-Fe^(2+)-Mg^(2+)-C_(2)O_(4)^(2-)-H_(2)O system is used to guide the design and preparation of insitu Mg-doped(Fe_(0.4)Mn_(0.6))_(1-x)Mg_(x)C_(2)O_(4)intermediate,which is then employed as an innovative precursor to synthesize high-performance Mg-doped LiFe_(0.4)Mn_(0.6)PO_(4).It indicates that the metal ions with a high precipitation efficiency and the stoichiometric precursors with uniform element distribution can be achieved under the optimized thermodynamic conditions.Meanwhile,accelerated Li+diffusivity and reduced charge transfer resistance originating from Mg doping are verified by various kinetic characterizations.Benefiting from the contributions of inherited homogeneous element distribution,small particle size,uniform carbon layer coating,enhanced Li+migration ability and structural stability induced by Mg doping,the Li(Fe_(0.4)Mn_(0.6))_(0.97)Mg_(0.03)PO_(4)/C exhibits splendid electrochemical performance.

Density functional theory study of B- and Si-doped carbons and their adsorption interactions with sulfur compounds

Understanding the adsorption interactions between carbon materials and sulfur compounds has far-reaching impacts,in addition to their well-known important role in energy storage and conversion,such as lithium-ion batteries.In this paper,properties of intrinsic B or Si single-atom doped,and B-Si codoped graphene(GR)and graphdiyne(GDY)were investigated by using density functional theory-based calculations,in which the optimal doping configurations were explored for potential applications in adsorbing sulfur compounds.Results showed that both B or Si single-atom doping and B-Si codoping could substantially enhance the electron transport properties of GR and GDY,improving their surface activity.Notably,B and Si atoms displayed synergistic effects for the codoped configurations,where B-Si codoped GR/GDY exhibited much better performance in the adsorption of sulfurcontaining chemicals than single-atom doped systems.In addition,results demonstrated that,after B-Si codoping,the adsorption energy and charge transfer amounts of GDY with sulfur compounds were much larger than those of GR,indicating that B-Si codoped GDY might be a favorable material for more effectively interacting with sulfur reagents.

Cation-doped LiNi_(0.8)Co_(0.1)Mn_(0.1)O_(2) cathode with high rate performance

The nickel-rich layered cathode material LiNi_(0.8)Co_(0.1)Mn_(0.1)O_(2)(NCM811)has high energy density,lower cost and is a promising cathode material currently under development.However,its electrochemical and structural stability is poor during cycling.Among the many modification methods,cation doping has been consistently proven to be an effective strategy for enhancing electrochemical performance.Herein,the NCM811 cathode material was modified by solid-phase reactions with Mg and Al doped.In addition,the corresponding mechanism of NCM811 cathode material-doped modification is explored by density functional theory(DFT)calculations,and we have extended this approach to other ternary cathode materials with different ratios and obtained universal laws.Combined with DFT calculations,the results show that Mg2+occupies the Li+site and reduces the degree of Li^(+)/Ni^(2+) mixture;Al^(3+) acts as a structural support during charging and discharging to prevent structural collapse.The electrochemical properties were tested by an electrochemical workstation and the LAND system,and the results showed that the capacity retention rate increased to varying degrees from 63.66%to 69.87%and 89.05%for NCM811-Mg and NCM811-Al at room temperature after 300 cycles,respectively.This study provides a theoretical basis and design strategy for commercializing cationic-doped modification of nickel-rich cathode materials.

Stable multi-electron reaction stimulated by W doping VS_(4)for enhancing magnesium storage performance

Rechargeable magnesium batteries(RMBs)hold promise for offering higher volumetric energy density and safety features,attracting increasing research interest as the next post lithium-ion batteries.Developing high performance cathode material by inducing multi-electron reaction process as well as maintaining structural stability is the key to the development and application of RMBs.Herein,multielectron reaction occurred in VS_(4)by simple W doping strategy.W doping induces valence of partial V as V^(2+)and V^(3+)in VS_(4)structure,and then stimulates electrochemical reaction involving multi-electrons in 0.5%W-V-S.The flower-like microsphere morphology as well as rich S vacancies is also modulated by W doping to neutralize structure change in such multi-electron reaction process.The fabricated 0.5%W-V-S delivers higher specific capacity(149.3 m A h g^(-1)at 50 m A g^(-1),which is 1.6 times higher than that of VS_(4)),superior rate capability(76 mA h g^(-1)at 1000 mA g^(-1)),and stable cycling performance(1500cycles with capacity retention ratio of 93.8%).Besides that,pesudocapaticance-like contribution analysis as well as galvanostatic intermittent titration technique(GITT)further confirms the enhanced Mg^(2+)storage kinetics during such multi-electron involved electrochemical reaction process.Such discovery provides new insights into the designing of multi-electron reaction process in cathode as well as neutralizing structural change during such reaction for realizing superior electrochemical performance in energy storage devices.