C/Mo duplex coating interfacially modified SiC fiber-reinforced γ-TiAl matrix composite （SiCf/C/Mo/γ-TiA1） was prepared by foil-fiber-foil method to investigate its interfacial modification effect. SiCf/C/TiAl com...C/Mo duplex coating interfacially modified SiC fiber-reinforced γ-TiAl matrix composite （SiCf/C/Mo/γ-TiA1） was prepared by foil-fiber-foil method to investigate its interfacial modification effect. SiCf/C/TiAl composites were also prepared under the same processing condition for comparision. Both kinds of the composites were thermally exposed in vacuum at 800 and 900℃ for different durations in order to study thermal stability of the interfacial zone. With the aids of scanning electron microscope （SEM） and energy dispersive spectrometer （EDS）, the interracial microstructures of the composites were investigated. The results reveal that, although adding the Mo coating, the interfacial reaction product of the SiCf/C/Mo/TiAl composite is the same with that of the SiCf/C/TiA1 composite, which is TiC/Ti2AlC between the coating and the matrix. However, C/Mo duplex coating is more efficient in hindering interfacial reaction than C single coating at 900 ℃ and below. In addition, a new layer of interfacial reaction product was found between Ti2AlC and the matrix after 900 ℃, 200 h thermal exposure, which is rich in V and close to the chemical composition of B2 phase.展开更多
Prenitridation of the TiBx coating surface of the Sigma SM1240 SiC fiber can form more stable compounds at the surface and obstruct the release of boron atoms into the Ti-based alloy matrix. The effect of nitridation ...Prenitridation of the TiBx coating surface of the Sigma SM1240 SiC fiber can form more stable compounds at the surface and obstruct the release of boron atoms into the Ti-based alloy matrix. The effect of nitridation on the tensile strength of the fiber was investigated in this work. Nitridation could degrade the tensile strength of the SiC fiber if the treating temperature and time are not optimized. The chemical reaction between the W core and SiC and the modification of fiber microstructure during the nitridation are responsible for the degradation in strength. The strength can be maintained by further optimization of the treating temperature and time. Therefore, stabilizing the surface of TiBx coating and hence the interface of the SiCf/Ti composite by the nitridation of the SiC fiber is a feasible technique for practical applications.展开更多
Microstructure of SiC fiber manufactured by chemical vapor deposition （CVD） onto tungsten （W） wire core was investigated by analytical electron microscopy （AEM）. The results reveal that the fiber consists of W c...Microstructure of SiC fiber manufactured by chemical vapor deposition （CVD） onto tungsten （W） wire core was investigated by analytical electron microscopy （AEM）. The results reveal that the fiber consists of W core, SiC sheath and C-coating. SiC sheath could be subdivided into two parts according to whether containing C rich stripe, or not. An emphasis was put on W/SiC interfacial reaction products and the transition zone between sub-layers in SiC sheath. The W/SiC interface consists of three layers of reaction production, namely, W2C, W5Si3 and WC. And there are amounts of facet faults existing in （100） face of WC crystalline and two classes of stack faults in WC have been revealed. The formation essence of different sublayers in SiC sheath was also discussed.展开更多
SiC fibers were irradiated by 414.4-MeV^(112)Sn^(27.3+)ions to different fluences(5.0×10^(12),6.0×10^(13),1.6×10^(14),and 1.92×10^(15)ions/cm^(2)).^(112)Sn^(27.3+)deposited its energy mainly via el...SiC fibers were irradiated by 414.4-MeV^(112)Sn^(27.3+)ions to different fluences(5.0×10^(12),6.0×10^(13),1.6×10^(14),and 1.92×10^(15)ions/cm^(2)).^(112)Sn^(27.3+)deposited its energy mainly via electron energy loss and passed through the SiC fiber.Then,the mechanical properties and surface characteristics of fibers were studied using a specific single filament tensile test and field emission scanning electron microscopy.Results revealed that the carbon concentration on the fiber surface increased while the silicon concentration decreased.Moreover,the addition of oxygen was found to correlate with an increase in ion fluence.Meanwhile,the fiber surface morphology of the least fluence(5.0×10^(12)ions/cm^(2))irradiated specimen displayed no obvious changes and its diameter was slightly reduced.With successive increases of ion fluence,large grains/bubbles on the fiber surface first appeared and then disappeared,and the diameter of fibers evidently increased.Moreover,at the highest fluence(1.92×10^(15)Sn ions/cm^(2))irradiated specimen,some fibers were brittle fractured.As a result,the mean tensile strength and the average elastic modulus of the fibers generally decreased with respect to the ion fluence.The degradation mechanisms of mechanical properties of SiC fibers under irradiation are discussed in detail.展开更多
Composite felts reinforced by both SiC nano-fibers(SiC-NFs)and carbon fibers were prepared at 1 273 K using Ni granules as catalyzers with different deposition time.SiC-NFs were deposited on the surface of the carbon ...Composite felts reinforced by both SiC nano-fibers(SiC-NFs)and carbon fibers were prepared at 1 273 K using Ni granules as catalyzers with different deposition time.SiC-NFs were deposited on the surface of the carbon fibers in situ by catalytic chemical vapor deposition(CCVD).The phase,microstructure and morphology of the fibers after electroplating and deposition were characterized by XRD,SEM and TEM.The results show that the SiC-NFs produced by CCVD are composed of single crystal of β-SiC.It is found that smaller nano-granules are more active as catalyzers.The resulting SiC-NFs appear more spindle-like and have a more homogeneous dispersion.The mass change of the samples before and after deposition shows that using more Ni granules results in a faster growth velocity of SiC-NFs.With the same electroplating time,the growth velocity of the SiC-NFs first increases and then decreases.At around 4 h,it reaches the maximum growth velocity,and it becomes nearly constant at around 8 h.After 8 h, the stable growth velocity of the electroplated Ni samples is faster than that of the conventional sample produced without catalyzers, because the SiC-NFs can improve the specific surface area and the activity of the surface.展开更多
Three types of SiC fibers with different tensile strength were employed to prepare unidirectional titanium matrix composites. The strengths of the original SiC fibers and extracted fibers from the composites were meas...Three types of SiC fibers with different tensile strength were employed to prepare unidirectional titanium matrix composites. The strengths of the original SiC fibers and extracted fibers from the composites were measured. The results show that the mechanical properties of fibers are greatly damaged by the consolidation processing of the composite. The strength data of the extracted fibers are used to predict the strength of the composites according to two theoretic models. The Globe Load-Sharing(GLS) model overestimates the strength of the composites. If the Local Load-Sharing(LLS) model assumes that failure occurs after the formation of a cluster with three broken fibers, the model can predict the strength of the composites exactly.展开更多
SCS-6 SiC continuous fiber-reinforced Ti-Al intermetallics-matrix composites were fabricated by HIP method and then heat-treated in vacuum under different conditions. The interfacial reaction kinetics and mechanism we...SCS-6 SiC continuous fiber-reinforced Ti-Al intermetallics-matrix composites were fabricated by HIP method and then heat-treated in vacuum under different conditions. The interfacial reaction kinetics and mechanism were studied by using SEM, EDS and XRD. The results show that the content fluctuation of reactive elements such as C, Ti and Si appears in interfacial reaction layers, and multi-layer interfacial reaction compounds form. Alloying element Nb in matrix remarkably diffuses into interfacial reaction zone and changes the activation energy for the interfacial reaction layer growth following a role of parabolic rate. The activation energy (Qk) and (k0) of SCS-6 SiC/super α2 and SCS-6 SiC/Ti2AlNb are 317.664 kJ/mol, 175.709 kJ/mol and 5.4438×10-2 m/s1/2, 1.44×10-5 m/s1/2; respectively, and the diffusion coefficient (DC) is about 10-18—10-20 m2/s. It is confirmed that the SCS-6 SiC/Ti-Al intermetallic composites have higher interface compatibility and stability. Furthermore, compared with SCS-6 SiC/super α2, the interface compatibility and stability of SCS-6 SiC/Ti2AlNb are even higher.展开更多
Air-curing is usually applied to the polymer-derived SiC fibers and, as a result, oxygen is embedded to the material. An effective relationship between oxygen content of the SiC fibers and mass gain of their precursor...Air-curing is usually applied to the polymer-derived SiC fibers and, as a result, oxygen is embedded to the material. An effective relationship between oxygen content of the SiC fibers and mass gain of their precursor fibers was established. Results also showed that oxygen content has a great influence on the mechanical properties and excellent tensile strength is usually obtained at the oxygen content of 12%～13%, similar to the density of SiC fibers. Oxygen content has a positive effect on the ceramic yield, and thus, is good to the density and tensile strength; while, oxygen content is also negative to volume content of SiC phase and crystallization of the SiC fibers, and thus, detrimental to the density and tensile strength. Both of the two effects result in the peak behavior of the tensile strength of SiC fibers.展开更多
In order to explore the effect of high-temperature annealing on the mechanical performances and microstructures of different oxygen SiC fibers, two types of silicon carbide（SiC）-based fibers, specified as XD-SiC fib...In order to explore the effect of high-temperature annealing on the mechanical performances and microstructures of different oxygen SiC fibers, two types of silicon carbide（SiC）-based fibers, specified as XD-SiC fibers（low oxygen） and Nicalon-201 fibers（high oxygen）, were annealed in Ar for 1 h at 800 ℃, 1 000 and 1 200 ℃, respectively. Mechanical properties of these fibers were characterized via a monofilament tensile method, with observation of the damaged monofilament by SEM. Also, the effects of annealing on the microstructure and chemical compositions of the fibers were studied. The experimental results indicated that the tensile strength decreased with the increase of annealing temperatures,after annealing-treatment at 1200℃, XD-SiC fibers remained 84% of its original strength, while Nicalon-201 fibers remained only 58% of its original strength. Crystallization and chemical composition of the fibers are the dominating factors for their mechanical performance at high temperatures. The microstructure changes of XD-SiC fibers are mainly composed of the growth of β-SiC, for Nicalon-201 fibers, evaporation of gases is the main change for microstructure.展开更多
The tensile strength of CVD SiC fiber was remarkably improved by electrochemical surface treatment. SEM analyses reveal that AC current treatment could form a more compact and complete SiO2 layer than DC current on th...The tensile strength of CVD SiC fiber was remarkably improved by electrochemical surface treatment. SEM analyses reveal that AC current treatment could form a more compact and complete SiO2 layer than DC current on the surface of the SiC fiber, which was beneficial to the improvement of tensile strength. It was also verified that AC current was more effective for producing high performance SiC fiber with SiO2 surface layer than DC current. The frequency is a sensitive parameter for the process; but the signals of input current had relatively small effect on the tensile strength of SiC fiber. A further discussion for this phenomenon was completed. The proposed operational parameters are 0.3 A, 5 kHz of sine wave and 91 m/h of the receiving rate respectively.展开更多
In SiC（f）/Ti-6Al-4V composites, the microstructure of the matrix close to the fiber was different from that of the fiber-less material. Microstructure observations show that a layer of fine grains was located adjace...In SiC（f）/Ti-6Al-4V composites, the microstructure of the matrix close to the fiber was different from that of the fiber-less material. Microstructure observations show that a layer of fine grains was located adjacent to the fiber, and more dislocations and faults were found in this region. Higher recrystallization nucleation rate due to the undeformed SiC fiber and thermal residual stress induced during cooling from the fabrication temperature caused the microstructural changes of the matrix. Hardness measurement indicates that the matrix in the fiber neighborhood was strengthened, and the strengthening effect decreased with distance away from the fiber.展开更多
A unique SiC whisker wheel was invented,in which the whiskers were aligned normally to the grinding wheel surface.In this paper,grindabilities of the SiC whisker wheel are investigated and compared with those of other...A unique SiC whisker wheel was invented,in which the whiskers were aligned normally to the grinding wheel surface.In this paper,grindabilities of the SiC whisker wheel are investigated and compared with those of other wheels of SiC grains,Al2O3 grains,as well as Al2O3 long and short fibres which were also aligned normally to the grinding wheel surface,respectively.The main research contents concern grinding characteristics of a directionally aligned SiC whisker wheel such as material-removal volume,wheel-wear rates,integrity of the ground surfaces,grinding ratios and grinding efficiency.Furthermore,grinding wheels of whiskers and fibres have a common disadvantage:they tend to load easily.The authors have proposed a simple method of loading-free grinding to overcome this propensity and investigate some related grinding characteristics under loading-free grinding conditions.展开更多
C f/SiC composites were prepared by precursor pyrolysis hot pressing, and the effect of fiber characteristics on the fracture behavior of the composites was investigated. Because the heat treatment temperature of fibe...C f/SiC composites were prepared by precursor pyrolysis hot pressing, and the effect of fiber characteristics on the fracture behavior of the composites was investigated. Because the heat treatment temperature of fiber T300 (below 1?500?℃) was much lower than that of fiber M40JB (over 2?000?℃), fiber T300 had lower degree of graphitization and consisted of more impurities compared with fiber M40JB, suggesting that T300 exhibits higher chemical activity. As a result, the composite with T300 showed a brittle fracture behavior, which is mainly ascribed to a strongly bonded fiber/matrix interface as well as the degradation of fibers during the preparation of the composite. However, the composite with M40JB exhibits a tough fracture behavior, which is primarily attributed to a weakly bonded fiber/matrix interface and higher strength retention of the fibers.展开更多
基金Projects(51201134,51271147)supported by the National Natural Science Foundation of ChinaProject(2015JM5181)supported by the Natural Science Foundation of Shaanxi Province,China+1 种基金Project(115-QP-2014)supported by the Research Fund of the State Key Laboratory of Solidification Processing(NWPU),ChinaProject(3102014JCQ01023)supported by the Fundamental Research Funds for the Central Universities,China
文摘C/Mo duplex coating interfacially modified SiC fiber-reinforced γ-TiAl matrix composite （SiCf/C/Mo/γ-TiA1） was prepared by foil-fiber-foil method to investigate its interfacial modification effect. SiCf/C/TiAl composites were also prepared under the same processing condition for comparision. Both kinds of the composites were thermally exposed in vacuum at 800 and 900℃ for different durations in order to study thermal stability of the interfacial zone. With the aids of scanning electron microscope （SEM） and energy dispersive spectrometer （EDS）, the interracial microstructures of the composites were investigated. The results reveal that, although adding the Mo coating, the interfacial reaction product of the SiCf/C/Mo/TiAl composite is the same with that of the SiCf/C/TiA1 composite, which is TiC/Ti2AlC between the coating and the matrix. However, C/Mo duplex coating is more efficient in hindering interfacial reaction than C single coating at 900 ℃ and below. In addition, a new layer of interfacial reaction product was found between Ti2AlC and the matrix after 900 ℃, 200 h thermal exposure, which is rich in V and close to the chemical composition of B2 phase.
基金The authors wish to thank the Royal Society, UK, and the Chinese Academy of Sciences for sponsoring a joint project-Grant No.761. The nitridation of the SiC fiber (Sigma SM1240) was carried out at QM, University of London, UK. Supply of the SiC fiber by
文摘Prenitridation of the TiBx coating surface of the Sigma SM1240 SiC fiber can form more stable compounds at the surface and obstruct the release of boron atoms into the Ti-based alloy matrix. The effect of nitridation on the tensile strength of the fiber was investigated in this work. Nitridation could degrade the tensile strength of the SiC fiber if the treating temperature and time are not optimized. The chemical reaction between the W core and SiC and the modification of fiber microstructure during the nitridation are responsible for the degradation in strength. The strength can be maintained by further optimization of the treating temperature and time. Therefore, stabilizing the surface of TiBx coating and hence the interface of the SiCf/Ti composite by the nitridation of the SiC fiber is a feasible technique for practical applications.
文摘Microstructure of SiC fiber manufactured by chemical vapor deposition （CVD） onto tungsten （W） wire core was investigated by analytical electron microscopy （AEM）. The results reveal that the fiber consists of W core, SiC sheath and C-coating. SiC sheath could be subdivided into two parts according to whether containing C rich stripe, or not. An emphasis was put on W/SiC interfacial reaction products and the transition zone between sub-layers in SiC sheath. The W/SiC interface consists of three layers of reaction production, namely, W2C, W5Si3 and WC. And there are amounts of facet faults existing in （100） face of WC crystalline and two classes of stack faults in WC have been revealed. The formation essence of different sublayers in SiC sheath was also discussed.
基金the National Natural Science Foundation of China(Nos.11675231,91426304)the Sichuan Science and Technology Program(No.2022YFG0263)the Scientific Research Starting Foundation for talents(Nos.21zx7109,21zx7110).
文摘SiC fibers were irradiated by 414.4-MeV^(112)Sn^(27.3+)ions to different fluences(5.0×10^(12),6.0×10^(13),1.6×10^(14),and 1.92×10^(15)ions/cm^(2)).^(112)Sn^(27.3+)deposited its energy mainly via electron energy loss and passed through the SiC fiber.Then,the mechanical properties and surface characteristics of fibers were studied using a specific single filament tensile test and field emission scanning electron microscopy.Results revealed that the carbon concentration on the fiber surface increased while the silicon concentration decreased.Moreover,the addition of oxygen was found to correlate with an increase in ion fluence.Meanwhile,the fiber surface morphology of the least fluence(5.0×10^(12)ions/cm^(2))irradiated specimen displayed no obvious changes and its diameter was slightly reduced.With successive increases of ion fluence,large grains/bubbles on the fiber surface first appeared and then disappeared,and the diameter of fibers evidently increased.Moreover,at the highest fluence(1.92×10^(15)Sn ions/cm^(2))irradiated specimen,some fibers were brittle fractured.As a result,the mean tensile strength and the average elastic modulus of the fibers generally decreased with respect to the ion fluence.The degradation mechanisms of mechanical properties of SiC fibers under irradiation are discussed in detail.
基金Project(2006CB600904)supported by the National Basic Research Program of China
文摘Composite felts reinforced by both SiC nano-fibers(SiC-NFs)and carbon fibers were prepared at 1 273 K using Ni granules as catalyzers with different deposition time.SiC-NFs were deposited on the surface of the carbon fibers in situ by catalytic chemical vapor deposition(CCVD).The phase,microstructure and morphology of the fibers after electroplating and deposition were characterized by XRD,SEM and TEM.The results show that the SiC-NFs produced by CCVD are composed of single crystal of β-SiC.It is found that smaller nano-granules are more active as catalyzers.The resulting SiC-NFs appear more spindle-like and have a more homogeneous dispersion.The mass change of the samples before and after deposition shows that using more Ni granules results in a faster growth velocity of SiC-NFs.With the same electroplating time,the growth velocity of the SiC-NFs first increases and then decreases.At around 4 h,it reaches the maximum growth velocity,and it becomes nearly constant at around 8 h.After 8 h, the stable growth velocity of the electroplated Ni samples is faster than that of the conventional sample produced without catalyzers, because the SiC-NFs can improve the specific surface area and the activity of the surface.
基金Project(50371069) supported by the National Natural Science Foundation of Chinaproject(2006B20) supported by the Doctoral Innovation Foundation of Northwestern Polytechnical University, China
文摘Three types of SiC fibers with different tensile strength were employed to prepare unidirectional titanium matrix composites. The strengths of the original SiC fibers and extracted fibers from the composites were measured. The results show that the mechanical properties of fibers are greatly damaged by the consolidation processing of the composite. The strength data of the extracted fibers are used to predict the strength of the composites according to two theoretic models. The Globe Load-Sharing(GLS) model overestimates the strength of the composites. If the Local Load-Sharing(LLS) model assumes that failure occurs after the formation of a cluster with three broken fibers, the model can predict the strength of the composites exactly.
基金Project(50371069) suppported by the National Natural Science Foundation of China Project(20030699013) suported by the State Educational Ministry Doctoral Foundation+1 种基金 Project(04G53044) supported by the Foundation of Aviation Science Project(ZX200301014) supported by the Materials Engineering Center Foundation of Jiangxi Province, China
文摘SCS-6 SiC continuous fiber-reinforced Ti-Al intermetallics-matrix composites were fabricated by HIP method and then heat-treated in vacuum under different conditions. The interfacial reaction kinetics and mechanism were studied by using SEM, EDS and XRD. The results show that the content fluctuation of reactive elements such as C, Ti and Si appears in interfacial reaction layers, and multi-layer interfacial reaction compounds form. Alloying element Nb in matrix remarkably diffuses into interfacial reaction zone and changes the activation energy for the interfacial reaction layer growth following a role of parabolic rate. The activation energy (Qk) and (k0) of SCS-6 SiC/super α2 and SCS-6 SiC/Ti2AlNb are 317.664 kJ/mol, 175.709 kJ/mol and 5.4438×10-2 m/s1/2, 1.44×10-5 m/s1/2; respectively, and the diffusion coefficient (DC) is about 10-18—10-20 m2/s. It is confirmed that the SCS-6 SiC/Ti-Al intermetallic composites have higher interface compatibility and stability. Furthermore, compared with SCS-6 SiC/super α2, the interface compatibility and stability of SCS-6 SiC/Ti2AlNb are even higher.
文摘Air-curing is usually applied to the polymer-derived SiC fibers and, as a result, oxygen is embedded to the material. An effective relationship between oxygen content of the SiC fibers and mass gain of their precursor fibers was established. Results also showed that oxygen content has a great influence on the mechanical properties and excellent tensile strength is usually obtained at the oxygen content of 12%～13%, similar to the density of SiC fibers. Oxygen content has a positive effect on the ceramic yield, and thus, is good to the density and tensile strength; while, oxygen content is also negative to volume content of SiC phase and crystallization of the SiC fibers, and thus, detrimental to the density and tensile strength. Both of the two effects result in the peak behavior of the tensile strength of SiC fibers.
文摘In order to explore the effect of high-temperature annealing on the mechanical performances and microstructures of different oxygen SiC fibers, two types of silicon carbide（SiC）-based fibers, specified as XD-SiC fibers（low oxygen） and Nicalon-201 fibers（high oxygen）, were annealed in Ar for 1 h at 800 ℃, 1 000 and 1 200 ℃, respectively. Mechanical properties of these fibers were characterized via a monofilament tensile method, with observation of the damaged monofilament by SEM. Also, the effects of annealing on the microstructure and chemical compositions of the fibers were studied. The experimental results indicated that the tensile strength decreased with the increase of annealing temperatures,after annealing-treatment at 1200℃, XD-SiC fibers remained 84% of its original strength, while Nicalon-201 fibers remained only 58% of its original strength. Crystallization and chemical composition of the fibers are the dominating factors for their mechanical performance at high temperatures. The microstructure changes of XD-SiC fibers are mainly composed of the growth of β-SiC, for Nicalon-201 fibers, evaporation of gases is the main change for microstructure.
文摘The tensile strength of CVD SiC fiber was remarkably improved by electrochemical surface treatment. SEM analyses reveal that AC current treatment could form a more compact and complete SiO2 layer than DC current on the surface of the SiC fiber, which was beneficial to the improvement of tensile strength. It was also verified that AC current was more effective for producing high performance SiC fiber with SiO2 surface layer than DC current. The frequency is a sensitive parameter for the process; but the signals of input current had relatively small effect on the tensile strength of SiC fiber. A further discussion for this phenomenon was completed. The proposed operational parameters are 0.3 A, 5 kHz of sine wave and 91 m/h of the receiving rate respectively.
文摘In SiC（f）/Ti-6Al-4V composites, the microstructure of the matrix close to the fiber was different from that of the fiber-less material. Microstructure observations show that a layer of fine grains was located adjacent to the fiber, and more dislocations and faults were found in this region. Higher recrystallization nucleation rate due to the undeformed SiC fiber and thermal residual stress induced during cooling from the fabrication temperature caused the microstructural changes of the matrix. Hardness measurement indicates that the matrix in the fiber neighborhood was strengthened, and the strengthening effect decreased with distance away from the fiber.
文摘A unique SiC whisker wheel was invented,in which the whiskers were aligned normally to the grinding wheel surface.In this paper,grindabilities of the SiC whisker wheel are investigated and compared with those of other wheels of SiC grains,Al2O3 grains,as well as Al2O3 long and short fibres which were also aligned normally to the grinding wheel surface,respectively.The main research contents concern grinding characteristics of a directionally aligned SiC whisker wheel such as material-removal volume,wheel-wear rates,integrity of the ground surfaces,grinding ratios and grinding efficiency.Furthermore,grinding wheels of whiskers and fibres have a common disadvantage:they tend to load easily.The authors have proposed a simple method of loading-free grinding to overcome this propensity and investigate some related grinding characteristics under loading-free grinding conditions.
文摘C f/SiC composites were prepared by precursor pyrolysis hot pressing, and the effect of fiber characteristics on the fracture behavior of the composites was investigated. Because the heat treatment temperature of fiber T300 (below 1?500?℃) was much lower than that of fiber M40JB (over 2?000?℃), fiber T300 had lower degree of graphitization and consisted of more impurities compared with fiber M40JB, suggesting that T300 exhibits higher chemical activity. As a result, the composite with T300 showed a brittle fracture behavior, which is mainly ascribed to a strongly bonded fiber/matrix interface as well as the degradation of fibers during the preparation of the composite. However, the composite with M40JB exhibits a tough fracture behavior, which is primarily attributed to a weakly bonded fiber/matrix interface and higher strength retention of the fibers.
