Predicting the Stitch Density of Finished Fabrics Using Weft Blended Grey Knit Fabrics

Stitch density is one of the critical quality parameters of knit fabrics. This parameter is closely related to other physical quality parameters like fabric weight, fabric tightness factor, fiber types, blend ratio, yarn diameter and linear density, and fabric structure. Selecting stitch density (wales per inch, course per inch) is essential to getting the appropriate fabric weight and desired quality. Usually, no rules or assumptions exist to get the desired stitch density in the finished fabric stage. Fifteen types of blended knit fabrics were prepared to conduct the study. The varying percentages of cotton, polyester, and elastane are incorporated in the blends. Regression analysis and regression ANOVA tests were done to predict the stitch density of finished fabrics. A suitable regression equation is established to get the desired results. The study also found that the stitch density value in the finished stage fabric decreases by approximately 15% compared to the stitch density in the grey fabric stage. This study will help the fabric manufacturers get the finished fabric stitch density in advance by utilizing the grey fabric stitch density data set. The author expects this research to benefit the knitting and dyeing industry, new researchers, and advanced researchers.

Studying the Effect of Polyester Fiber Blend Ratio and Pilling Cycle on Blended Knit Fabrics

Pilling is a severe concern for blended fabrics. The aesthetic look and smoothness are the buyers’ prime requirements. The main focus of the study was to see the pilling behavior from various percentages of polyester fiber blend ratio as well as the different pilling cycles on blended fabrics. The cotton, polyester, and elastane prepared the study fabrics. These fabrics are (90% Cotton/5% Polyester/5% Elastane, 90% Cotton/6% Polyester/4% Elastane, 90% Cotton/7% Polyester/3% Elastane, 90% Cotton/8% Polyester/2% Elastane, and 90% Cotton/9% Polyester/1% Elastane, 85% Cotton/10% Polyester/5% Elastane, 85% Cotton/11% Polyester/4% Elastane, 85% Cotton/12% Polyester/3% Elastane, 85% Cotton/13% Polyester/2% Elastane, and 85% Cotton/ 14% Polyester/1% Elastane, 80% Cotton/15% Polyester/5% Elastane, 80% Cotton/16% Polyester/4% Elastane, 80% Cotton/17% Polyester/3% Elastane, 80% Cotton/18% Polyester/2% Elastane, and 80% Cotton/19% Polyester/1% Elastane). The selected polyester blend ratios were 5%, 6%, 7%, 8%, 9%, 10%, 11%, 12%, 13%, 14%, 15%, 16%, 17%, 18% and 19% respectively. The study used the Martindale pilling tester with 2000, 5000, and 7000 cycles, respectively. The evaluation followed the ISO 12945-2:2000. The study findings are that the polyester fiber blend ratio did not influence the pilling grade on blended fabrics for pilling cycles 2000, and the pilling grade remained constant at 4 - 5. The pilling grade started to deteriorate in pilling cycle 5000 for the fabrics 85%C/10%P/5%E, 85%C/11%P/4%E, 85%C/12%P/3%E, 85%C/ 13%P/2%E, 85%C/14%P/1%E showed the pilling grade 4, and the fabrics made from 80%C/15%P/5%E, 80%C/16%P/4%E, 80%C/17%P/3%E, 80%C/ 18%P/2%E, 80%C/19%P/1%E showed the pilling grade 4, 3, 3, 3, and 3 respectively. For the pilling cycles 7000, the pilling grade further deteriorated for the fabrics 80%C/15%P/5%E, 80%C/16%P/4%E, 80%C/17%P/3%E, 80%C/ 18%P/2%E, 80%C/19%P/1%E showed the pilling grade 3, 3, 2, 2, and 2 respectively. The study finds the dominance of polyester fiber throughout the experiment. The author hopes this study’s outcome will help new researchers, advanced researchers, and the textile industry’s sustainable development research and development team.

A MICRO-MECHANICAL MODEL OF KNITTED FABRIC AND ITS APPLICATION TO THE ANALYSIS OF BUCKLING UNDER TENSION IN WALE DIRECTION:MICRO-MECHANICAL MODEL

The typical micro-knitting structure of knitted fabric,which makes it very different from woven fabric,is described.The tensile tests of knitted fabric are reported.The deformations of the micro-knitting structures are carefully studied.The study indicates that when a knitted fabric sheet is subjected to a tension along w-direction an extra compressive stress field inside loop in c-direction is induced.The extra stress field is also determined through analysis.Finally,a micro-mechanical model of knitted fabric is proposed.This work paves the way for the simulations of buckling modes of a knitted fabric sheet as are observed in experiments.

Prediction of the thermo-elastic properties of knitted structural composites using FEM

It is a very important and complex task to estimate the thermo-elasticproperties of a textile structural composite. In this paper, the finite element method (FEM) wasused for the prediction of the orthotropic thermo-elastic properties of a composite reinforced byglass fiber knitted fabric. In order to define the final 3-D configuration of the loop reinforcingstructure, the interactions between the adjacent loops, the large displacement and the contactelements without friction were considered. The values predicted were compared with the experimentalresults.

Development of Warp Knitted Products on RSJ Machine

Products made by Raschel Jacquard(RSJ)high-speed jacquard warp knitting machine are used in ornament and apparel fabrics.However,most products are produced according to the existing samples.The capability of creative design is not enough at home.In this paper,based on the basic features,the knitting methods and the working principles of warp knitting jacquard machines,the rules for manufacturing jacquard products are summarized.The article provides the new thoughts for the development of fabrics,such as the pattern design,changing the cams,power-net and a special technology of without pillar,which were obtained from the practices in a factory.

Study of the Effect of Changes on the Technological and Physical-Mechanical Properties of Knitting in a New Structure

In this article, we compared four types of knitted fabrics with high two-ply shape retention. Experimental samples of a two-layer knitted fabric have been developed and graphic symbols have been applied on a flat-needle weaving machine of the 12th class LONG-XING SM 252 (China).

ON CRAFT OF SILK “KNITTING” CORDS OF WARRING STATES PERIOD IN JIANGLING

Seven pieces of silk braids excavated from Chu Tomb No.1 at M ashan in Jiangling are thoughtto belong to the knitting fabric.Their structures are double-stitched type,with a lining silk on theback side to fix the knitted threads;besides the traverse linking structure,there are alsomulti-structures by single jersey combined with traverse linking,the excavators declared.The au-thor of this paper believes that those cords can be classified as some intermediary between theknitwear and the needlework.They have the structure similar to certain kinds of knitting,crochetand embroidery,and can be duplicated through two different methods.The differences and similar-ities between these cords and the traditional hand-knitting or embroidery,as well as their originsare discussed.Photographs of the relic and the duplication are presented.

Compilation and Analysis Method for Computer Aided Pattern Design System Based on Fully-Fashioned Computerized Flat Knitting Machine

The knitting industry CAD/CAM system＇s development needs a solution of computer representation of the designed objects. One of them is a transformation of knitting rows and stitches form knitting pattern and its automatic analysis is to control data from the knitting design data. A method of the pattern CAD system including the analyzing and the compiling of the pattern data was developed in this paper. By rasterizing the pattern map, the drafted pattern could be compiled into knitting row data and stitches. The storage format of knitting rows data and stitches data could be defined by analyzing the motion of computerized fiat knitting machine. By reassembling the control data, it could be analyzed into the execute data of the controller in computerized fiat knitting machine. This method mainly focused on the weak areas of multi-needle-bed technology and fully-fashioned knitting technology in inland and could be applied to most of control systems in the master-slave mode. The knitting row data and pattern row data in a ＂ ＊. ptn＂ format file were integrated. Giving a corresponding analytic calculation process of control data and realizing independent development of the upper machine and the lower machine, the final knitting control data not only have low computation and transmission cost but also have fast transfer speeds.

Prediction of Buckling of Plain Knitted Fabric Sheets Subjected to Simple Shear in Wale Direction

Knitted fabric is very different from woven fabric due to its more complicated knitting structures. The buckling of knitted fabric sheets subjected to simple shear in the wale direction is investigated analytically in consideration of the large deformation of fabric sheet in critical configuration. The theory on instability of finite deformation is applied to the analysis. All the stress boundary conditions of knitted fabric sheet are satisfied. An equation to determine the buckling direction angle is derived. It is shown that there are two possible buckling modes, flexural mode and barreling mode. The buckling condition equations for the flexural mode and barreling mode are also obtained respectively. Numerical illustrations reveal that only the flexural mode can actually occur and the barreling mode cannot, which agrees with the experimental observations. For a permitted buckling mode on margin boundaries, the critical value of shear amount and the buckling direction angle can be determined.

Tensile Properties of Weft Knitted Fabric Reinforced Composites

Seven kinds of weft knitted fabrics from glass fiber yarns were used as reinforcement to make fabric/epoxy composite laminates. Tensile tests were carried out to examine and compare the mechanical properties in course and wale direction of these composites. On the basis of experimental results, attempts have been made to analyze some main factors influencing stress-strain curve, ultimate tensile strength and initial elastic modulus of specimens.

Investigation on the Dimensional Properties of Relaxed Plain Knitted Fabrics

A geometric model of relaxed plain-nitted fabric isproposed.A method based on the model for predictingthe loop length from the course spacing,wale spacing offabric and the diameter of yarn is deduced,as well as a computer program is developed to graphically represent the structures of plain knitted fabric with various struc-tural parameters.

Study of Single Plated Principle on Large Diameter Circular Weft Knitting Machine

A new theory and method that differs from the tradition-al single plated weft - knitting theory and method hasbeen expounded after theoretical analyzing and experi-mental proving. If the new method is used when platingstitch is knitted on large diameter weft knitting machine,the thorny problem of long standing that ground yarn iseasy to appear on the face side of fabric is solved. Thenew method, i.e, the production of physical ability oftraining uniform for serviceman has been used.

Wet Permeability and Moisture Vapor Transmission Characteristics of Soybean Knitted Fabrics

Wet permeability of fibrous assembly is mainly influenced by the properties of liquid and the configurations of the fiber which consist of diameter of fiber, twist angle and fiber alignment in a yarn. It can be seen from experimental results that the knitted fabric made of soybean (SB) fiber has goodproperties both in wet permeability and vapor transmission so that the knitting technology and fabric characteristics can be improved.

Finishing Effect on Warmth Property of Cotton/Kapok Blended Knitted Fabric

Nowadays,more and more natural or functional fibers are being investigated due to their utilization in thermal underwear.Kapok fiber is one of the natural cellulosic fibers whose source is the kapok plant. It has hollow body and sealed tail,which exhibits desirable features required for functional textiles of this nature. In this study,cotton / kapok( 80 /20 by mass) blended yarn with two types of yarn size 18. 5 and 14. 8 tex,respectively are knitted into plain stitches. The fabrics are undergone with an optimal preparation plan according to orthogonal design. Then,after dyeing and softening,fabric properties including thermal and water-vapour resistances, wicking property, pilling behaviour, and surface morphology,are tested and scrutinized for their candidacy for thermal underwear. The results showed that cotton / kapok blended fabrics have good thermal resistance which is significantly higher than those of cotton / modal blended fabrics,and the same water vapour resistance compared with cotton / modal blended fabrics which are normally used as underwear. Cotton / modal blended knitted fabrics has better pilling grade than cotton / kapok blended fabrics. Meanwhile, the cotton / kapok blends fabrics have good wicking property. Collectively,it was concluded that cotton / kapok blended fabric was appropriate for thermal underwear. However,the main limitation of these fabrics is their pilling properties.

Fabrication of a Knitted Biodegradable Stents for Tracheal Regeneration

Endoluminal stents for reinforcement and regeneration of human trachea have been developed by weft-knitting method on a small-diameter circular knitting machine. The constituent materials of the stent are Polyglactin, Polypropylene and Chitosan with Polyglactin and Polypropylene plate-stitched fabric acting as backbone while chitosan as matrix, respectively. The fabrication procedures including knitting and coating are described in this paper. Mechanical and animal tests have been carried out to evaluate the mechanical properties of the stents.

3D Modeling and Simulation of Fancy Fabrics in Weft Knitting

Weft knitted fancy fabrics are widely used in knitted garment design. Due to the complexity of the structures, their modeling and simulation needs to be solved in three-dimensional (3D) CAD developments. In this paper, 3D loop geometrical models of weft knitted fancy structures, including tuck stitch, jacquard stitch, transfer stitch and fleecy stitch, were developed based on an improved model of plain loop, and their central axes as some 3D space curves were achieved by using Non-Uniform Rational B-Splines (NURBS). The 3D visual simulation programme was written in C++ programming language using OpenGL, which was a function library of 3D graphics. Some examples of weft knitted fancy fabrics were generated and practical application of 3D simulation was discussed.

Study on How to Design Knitted Fabric Pattern with Mathematical Theory

To improve design capabilities for the knitted fabric pattern,a preliminary study is carried out for the design method.Based on mathematical theory,pattern could be created automatically by computer with inputting different parameters for mathematical functions.The knitted fabric simulation is realized by M1 CAD pattern preparation system of STOLL Company.In the pattern,different color unit is replaced by obverse stitch with different color,or by obverse stitch and reverse stitch with the same color separately,after that the effects of knitted fabrics could be simulated.Designing with this method,it would not only help to acquire a great of diversity patterns,but also improve design efficiency and save cost.

A micro-mechanical model of knitted fabric and its application to the analysis of buckling under tension in wale direction:buckling analysis

With the aid of the micro-mechanical model of knitted fabric proposed in Part 1 we analyze the buckling of a knitted fabric sheet when it is subjected to a tension along the wale direction. The large deformation of the fabric sheet in the critical configuration is considered and, to avoid possible deviation due to the approximation of the theory of thin plate, the three-dimensional theory of instability is used. The fabric sheet is considered as a three-dimensional body and all boundary conditions are satisfied. It is shown that the buckling of the fabric sheet is possible, two buckling modes and the corresponding buckling conditions are obtained, but only the flexural mode is physically possible as observed in experiments.

OPTIMAL SETTING-UP OF KNITTING ELEMENTS AND ITS EFFECT ON TENSION VARIATION

The dynamic yarn tension variations during knitting cycle are very difficult to control and be-come one of barriers to knitting on modern warp knitting machine.Examination of experimentaldata and theoretical analysis show that the relative position of spring rail to knitting elements suchas needle,guide as well as their displacement has noticeable effect on tension variation so that theknitting condition can be much improved by rearrangement of the knitting elements and theirmovement within a knitting cycle.

Effect of Run - in Ratios on the Mechanical Properties of Two - Guide Bars Warp - Knitted Fabrics

Warp knitting technology gets rapid development at present and becomes one of the most important parts of the textiles.But it is less known how the parameters of warp knitting technology affect the mechanical properties of warp-knitted fabrics.This paper presents discuss a research on the relationships between run-in ratio and mechanical properties of the two-bar warp-knittedfabrics through the measurement and analysis of the mechanical properties of various samples with different run-in ratios.The optimal run一in ratios for the reasonable mechanical properties are obtained from above dis-