NiO-Doped Fe_(2)O_(3)/MgO Properties for the Chemical Looping Oxidative Dehydrogenation of Ethane

Ethane chemical looping oxidative dehydrogenation(CL-ODH)to ethylene is a new technology for ethylene preparation.Fe_(2)O_(3)/MgO oxygen carrier was prepared using the co-precipitation method.The influence of added NiO and its different loadings on Fe_(2)O_(3)/MgO were investigated.Then,a series of oxygen carriers were applied in the CL-ODH of the ethane cycle system.Brunauer-Emmett-Teller(BET),X-ray diffractometry(XRD),X-ray photoelection spectroscopy(XPS),and H2-temperature programmed reduction(TPR)were used to characterize the physicochemical properties of these oxygen carriers.It was confirmed that an interaction between NiO and Fe_(2)O_(3) occurred based on the XPS and H2-TPR results.Based on the CL-ODH activity performance tests conducted in a fixed-bed reactor,it was revealed that ethylene selectivity was significantly improved after NiO addition.Fe_(2)O_(3)-10%NiO/MgO showed the best activity performance with 93%ethane conversion and 50%ethylene selectivity at a reaction temperature of 650℃,atmospheric pressure,and space velocity of 7500 mL/(g·h).

Chemical looping oxidative propane dehydrogenation controlled by oxygen bulk diffusion over FeVO_(4)oxygen carrier pellets

The oxygen distribution and evolution within the oxygen carrier exert significant influence on chemical looping processes.This paper describes the influence of oxygen bulk diffusion within FeVO4 oxygen carrier pellets on the chemical looping oxidative propane dehydrogenation(CL-ODH).During CL-ODH,the oxygen concentration at the pellet surface initially decreased and then maintained stable before the final decrease.At the stage with the stable surface oxygen concentration,the reaction showed a stable C3H6 formation rate and high C3H6 selectivity.Therefore,based on Fick’s second law,the oxygen distribution and evolution in the oxygen carrier at this stage were further analyzed.It was found that main reactions of selective oxidation and over-oxidation were controlled by the oxygen bulk diffusion.C3H8 conversion rate kept decreasing during this stage due to the decrease of the oxygen flux caused by the decline of oxygen gradient within the oxygen carrier,while C3H6 selectivity increased due to the decrease of overoxidation.In addition,reaction rates could increase with the propane partial pressure due to the increase of the oxygen gradient within the oxygen carrier until the bulk transfer reached its limit at higher propane partial pressure.This study provides fundamental insights for the diffusion-controlled chemical looping reactions.

Chemical looping conversion of methane via Fe_(2)O_(3)-LaFeO_(3)calcined from LaFe-MOF precursor

The effective utilization of natural gas resources is a promising option for the implementation of the"dual carbon"strategy.However,the capture of carbon dioxide with relatively lower concentration after the combustion of natural gas is the crucial step.Fortunately,the lattice oxygen is used for chemical cycle conversion of methane to overcome the shortcomings mentioned above.A method was proposed to synthesize perovskite for methane cycle conversion using metal organic framework as a precursor.Morphology and pore structure of Fe_(2)O_(3)-LaFeO_(3)composite oxides were regulated by precursor synthesis conditions and calcination process.Moreover,the chemical looping conversion performance of methane was evaluated.The results showed that the pure phase precursor of La[Fe(CN)_(6)]·5H_(2)O was synthesized with the specific surface area of 23.91 m^(2)·g^(-1)under the crystallization of 10 h and the pH value of10.5.Fe_(2)O_(3)-LaFeO_(3)was obtained by controlled calcination of La[Fe(CN)_(6)]·5H_(2)O and Fe_(2)O_(3)with variable mass ratio.The selectivity of CO_(2)can reach more than 99%under the optimal parameters of methane chemical looping conversion:m(Fe_(2)O_(3)):m(LaFeO_(3))=2:1,the reaction temperature is 900℃,the lattice oxygen conversion is less than 40%.Fe_(2)O_(3)-LaFeO_(3)still has good phase and structure stability after five redox reaction and regeneration cycles.

Microscopic mechanism study and process optimization of dimethyl carbonate production coupled biomass chemical looping gasification system

Biomass chemical looping gasification technology is one of the essential ways to utilize abundant biomass resources.At the same time,dimethyl carbonate can replace phosgene as an environmentfriendly organic material for the synthesis of polycarbonate.In this paper,a novel system coupling biomass chemical looping gasification with dimethyl carbonate synthesis with methanol as an intermediate is designed through microscopic mechanism analysis and process optimization.Firstly,reactive force field molecular dynamics simulation is performed to explore the reaction mechanism of biomass chemical looping gasification to determine the optimal gasification temperature range.Secondly,steady-state simulations of the process based on molecular dynamics simulation results are carried out to investigate the effects of temperature,steam to biomass ratio,and oxygen carrier to biomass ratio on the syngas yield and compositions.In addition,the main energy indicators of biomass chemical looping gasification process including lower heating value and cold gas efficiency are analyzed based on the above optimum parameters.Then,two synthesis stages are simulated and optimized with the following results obtained:the optimal temperature and pressure of methanol synthesis stage are 150℃ and 4 MPa;the optimal temperature and pressure of dimethyl carbonate synthesis stage are 140℃ and 0.3 MPa.Finally,the pre-separation-extraction-decantation process separates the mixture of dimethyl carbonate and methanol generated in the synthesis stage with 99.11%purity of dimethyl carbonate.Above results verify the feasibility of producing dimethyl carbonate from the perspective of multi-scale simulation and realize the multi-level utilization of biomass resources.

Techno-economic assessment of a chemical looping splitting system for H2 and CO Co-generation

The natural gas(NG)reforming is currently one of the low-cost methods for hydrogen production.However,the mixture of H2 and CO_(2) in the produced gas inevitably includes CO_(2) and necessitates the costly CO_(2) separation.In this work,a novel double chemical looping involving both combustion(CLC)and sorption-enhanced reforming(SE-CLR)was proposed towards the co-production of H2 and CO(CLC-SECLRHC)in two separated streams.CLC provides reactant CO_(2) and energy to feed SECLRHC,which generates hydrogen in a higher purity,as well as the calcium cycle to generate CO in a higher purity.Techno-economic assessment of the proposed system was conducted to evaluate its efficiency and economic competitiveness.Studies revealed that the optimal molar ratios of oxygen carrier(OC)/NG and steam/NG for reforming were recommended to be 1.7 and 1.0,respectively.The heat integration within CLC and SECLRHC units can be achieved by circulating hot OCs.The desired temperatures of fuel reactor(FR)and reforming reactor(RR)should be 850
C and 600
C,respectively.The heat coupling between CLC and SECLRHC units can be realized via a jacket-type reactor,and the NG split ratio for reforming and combustion was 0.53:0.47.Under the optimal conditions,the H2 purity,the H2 yield and the CH4 conversion efficiency were 98.76%,2.31 mol mol-1 and 97.96%,respectively.The carbon and hydrogen utilization efficiency respectively were 58.60% and 72.45%in terms of the total hydrogen in both steam and NG.The exergy efficiency of the overall process reached 70.28%.In terms of the conventional plant capacity(75 × 103 t y^(-1))and current raw materials price(2500$t^(-1)),the payback period can be 6.2 years and the IRR would be 11.5,demonstrating an economically feasible and risk resistant capability.

Simultaneous CO_(2) capture and thermochemical heat storage by modified carbide slag in coupled calcium looping and CaO/Ca(OH)2 cycles

The simultaneous CO_(2) capture and heat storage performances of the modified carbide slag with byproduct of biodiesel were investigated in the process coupled calcium looping and CaO/Ca(OH)2 thermochemical heat storage using air as the heat transfer fluid.The modified carbide slag with by-product of biodiesel exhibits superior CO_(2) capture and heat storage capacities in the coupled calcium looping and heat storage cycles.The hydration conversion and heat storage density of the modified carbide slag after 30 heat storage cycles are 0.65 mol·mol^(-1) and 1.14 GJ·t^(-1),respectively,which are 1.6 times as high as those of calcined carbide slag.The negative effect of CO_(2) in air as the heat storage fluid on the heat storage capacity of the modified carbide slag is overcome by introducing CO_(2) capture cycles.In addition,the CO_(2) capture reactivity of the modified carbide slag after the multiple calcium looping cycles is enhanced by the introduction of heat storage cycles.By introducing 10 heat storage cycles after the 10th and 15th CO_(2) capture cycles,the CO_(2) capture capacities of the modified carbide slag are subsequently improved by 32%and 43%,respectively.The porous and loose structure of modified carbide slag reduces the diffusion resistances of CO_(2) and steam in the material in the coupled process.The formed CaCO_(3)in the modified carbide slag as a result of air as the heat transfer fluid in heat storage cycles decomposes to regenerate CaO in calcium looping cycles,which improves heat storage capacity.Therefore,the modified carbide slag with by-product of biodiesel seems promising in the coupled calcium looping and CaO/Ca(OH)_(2) heat storage cycles.

Different oxidation routes for lattice oxygen recovery of double-perovskite type oxides LaSrFeCoO6 as oxygen carriers for chemical looping steam methane reforming

Double-perovskite type oxide LaSrFeCoO_6(LSFCO) was used as oxygen carrier for chemical looping steam methane reforming(CL-SMR) due to its unique structure and reactivity. Two different oxidation routes,steam-oxidation and steam-air-stepwise-oxidation, were applied to investigate the recovery behaviors of the lattice oxygen in the oxygen carrier. The characterizations of the oxide were determined by X-ray diffraction(XRD), X-ray photoelectron spectroscopy(XPS), hydrogen temperature-programmed reduction(H_2-TPR) and scanning electron microscopy(SEM). The fresh sample LSFCO exhibits a monocrystalline perovskite structure with cubic symmetry and high crystallinity, except for a little impurity phase due to the antisite defect of Fe/Co disorder. The deconvolution distribution of XPS patterns indicated that Co,and Fe are predominantly in an oxidized state(Fe^(3+) and Fe^(2+)) and(Co^(2+) and Co^(3+)), while O 1s exists at three species of lattice oxygen, chemisorbed oxygen and physical adsorbed oxygen. The double perovskite structure and chemical composition recover to the original state after the steam and air oxidation, while the Co ion cannot incorporate into the double perovskite structure and thus form the CoO just via individual steam oxidation. In comparison to the two different oxidation routes, the sample obtained by steam-oxidation exhibits even higher CH_4 conversion, CO and H_2 selectivity and stronger hydrogen generation capacity.

Petroleum coke conversion behavior in catalyst-assisted chemical looping combustion

Efficiently using petroleum coke as fuel and reducing carbon emission meanwhile have become attractive in oil processing industry.The paper is focused on the application of Chemical Looping Combustion(CLC)with petroleum coke,with the purpose of investigating its combustion performance and effects of potassium.Some experiments were performed in a laboratory scale fluidized bed facility with a natural manganese-based oxygen carrier.Experimental results indicated that the coke conversion is very sensitive to reaction temperature.The pre sent natural manganese-based oxygen carrier decorated by K has little effect on the improvement of coke conversion.XRD,SEM-EDX,and H2-TPR were adopted to characterize the reacted oxygen carrier samples.After being decorated by K,the oxygen carrier's capacity of transferring oxygen was decrea sed.A calcination temperature above the melting point of K2 CO3(891℃)shows better oxygen transfer reactivity in comparison to the one calcined at a lower temperature.The natural oxygen carrier used in the work has a high content of Si,which can easily react with K to form K(FeSi2 O6).Further,irrespective of reaction temperature,the coke conversion can be significantly enhanced by decorating the coke with K,with a demonstration of remarkably shorter reaction time,faster average coke gasification rate and higher average carbon conversion rate.

Solar chemical looping reforming of methane combined with isothermal H2O/CO2 splitting using ceria oxygen carrier for syngas production

The chemical looping reforming of methane through the nonstoichiometric ceria redox cycle(CeO2/CeO2-δ) has been experimentally investigated in a directly irradiated solar reactor to convert both solar energy and methane to syngas in the temperature range 900–1050 °C. Experiments were carried out with different ceria shapes via two-step redox cycling composed of endothermic partial reduction of ceria with methane and complete exothermic re-oxidation of reduced ceria with H2 O/CO2 at the same operating temperature, thereby demonstrating the capability to operate the cycle isothermally. A parametric study considering different ceria macrostructure variants(ceria packed powder, ceria packed powder mixed with inert Al2 O3 particles, and ceria reticulated porous foam) and operating parameters(methane flow-rate, reduction temperature, or sintering temperature) was conducted in order to unravel their impact on the bed-averaged oxygen non-stoichiometry(δ), syngas yield, methane conversion, and solar reactor performance. The ceria cycling stability was also experimentally investigated to demonstrate repeatable syngas production by alternating the flow between CH4 and H2 O(or CO2). A decrease in sintering temperature of the ceria foam was beneficial for increasing syngas selectivity, methane conversion,and reactor performance. Increasing both CH4 concentration and reduction temperature enhanced δ with the maximum value up to 0.41 but concomitantly favored CH4 cracking reaction. The ceria reticulated porous foam showed better performance in terms of effective heat transfer, due to volumetric absorption of concentrated solar radiation and uniform heating with lower solar power consumption, thereby promoting the solar-to-fuel energy conversion efficiency that reached up to 5.60%. The energy upgrade factor achieved during cycle was up to 1.19. Stable patterns in the δ and syngas yield for consecutive cycles with the ceria foam validated material performance stability.

Chemical looping gasification of maceral from low-rank coal: Products distribution and kinetic analysis on vitrinite

The product distribution and kinetic analysis of low-rank coal vitrinite were investigated during the chemical looping gasification(CLG)process.The acid washing method was used to treat low-rank coal,and the density gradient centrifugation method was adopted to obtain the coal macerals.By combining thermogravimetric analysis and online mass spectrometry,the influence of the heating rate and oxygen carrier(Fe2O3)blending ratio on product distribution was discussed.The macroscopic kinetic parameters were solved by the Kissinger-Akahira-Sunose(KAS)method,and the main gaseous product formation kinetic parameters were solved by the iso-conversion method.The results of vitrinite during slow heating chemical looping gasification showed that the main weight loss interval was 400–600℃,and the solid yield of sample vitrinite-Fe-10 at different heating rates was 64.30%–69.67%.When b=20℃·min^(-1),the maximum decomposition rate of vitrinite-Fe-10 was 0.312%min1.The addition of Fe2O_(3)reduced the maximum decomposition rate,but by comparing the chemical looping conversion characteristic index,it could be inferred that the chemical looping gasification of vitrinite might produce volatile substances higher than the pyrolysis process of vitrinite alone.The average activation energy of the reaction was significantly reduced during chemical looping gasification of vitrinite,which was lower than the average activation energy of 448.69 kJ·mol^(-1) during the pyrolysis process of vitrinite alone.The gaseous products were mainly CO and CO_(2).When the heating rate was 10℃·min^(-1),the highest activation energy for CH4 formation was 21.353 kJ·mol^(-1),and the lowest activation energy for CO formation was 9.7333 kJ·mol^(-1).This study provides basic data for exploring coal chemical looping gasification mechanism and reactor design by studying the chemical looping gasification process of coal macerals。

Chemical looping catalytic gasification of biomass over active LaNixFe1-xO_(3)perovskites as functional oxygen carriers

Oxygen carriers(OCs)with perovskite structure are attracting increasing interests due to their redox tunability by introducing various dopants in the structure.In this study,LaNixFe1-xO3(x=0,0.1,0.3,0.5,0.7,1.0)perovskite OCs have been prepared by a citric acid–nitrate sol–gel method,characterized by means of X-ray diffraction(XRD)analysis and tested for algae chemical looping gasification in a fixed bed reactor.The effects of perovskite types,OC/biomass mass ratio(O/B),gasification temperature and water injection rate on the gasification performance were investigated.Lower Ni-doped(0≤x≤0.5)perovskites crystalized in the rhombohedra system which was isostructural with LaNiO3,while those with composition 0.5≤x≤1 crystalized in the orthorhombic system.Despite the high reactivity for LaNiO_(3),LaNi_(0.5)Fe_(0.5)O_(3)(LN5F5)was found to be more stable at a high temperature and give almost as good results as LaNiO_(3)in the formation of syngas.The relatively higher syngas yield of 0.833 m^(3)·kg^(-1) biomass was obtained under the O/B of 0.4,water injection rate of 0.3 ml·min^(-1) and gasification temperature at 850C.Continuous high yield of syngas was achieved during the first 5 redox cycles,while a slight decrease in the reactivity for LN5F5 after 5 cycles was observed due to the adhesion of small grains occurring on the surface of OCs.However,an obvious improvement in the gasification performance was attained for LN5F5 compared to raw biomass direct gasification,indicating that LN5F5 is a promising functional OC for chemical looping catalytic gasification of biomass.

Chemical looping gasification of sewage sludge using copper slag modified by NiO as an oxygen carrier

Chemical looping gasification(CLG) provides a novel approach to dispose the sewage sludge.In order to improve the reactivity of the calcined copper slag,NiO modification is considered as one of the good solutions.The copper slag calcined at 1100℃ doped with 20 wt% NiO(Ni20-CS) was used as an oxygen carrier(OC) in sludge CLG in the work.The modification of NiO can evidently enhance the reactivity of copper slag to promote the sludge conversion,especially for sludge char conversion.The carbon conversion and valid gas yield(V_(g)) increase from 67.02% and 0.23 m^(3)·kg^(-1) using the original OC to 78.34% and 0.29 m^(3)·kg^(-1) using the Ni20-CS OC, respectively.The increase of equivalent coefficient(Ω) facilitates the sludge conversion and a suitable Ω value is determined at 0.47 to obtain the highest valid gas yield(0.29 m^(3)·kg^(-1)).A suitable steam content is assigned at 27.22% to obtain the maximum carbon conversion of 87.09%,where an acceptable LHV of 12.63 MJ·m^(-3) and Vg of 0.39 m^(3)·kg^(-1)are obtained.Although the reactivity of Ni20-CS OC gradually decreases with the increase in cycle numbers because of the generation of NiFe_(2) O_(4-δ) species,the deposition of sludge ash containing many metallic elements is beneficial to the sludge conversion.As a result,the carbon conversion shows a slight uptrend with the increase of cycle numbers in sludge CLG.It indicates that the Ni20-CS sample is a good OC for sludge CLG.

Numerical and experimental analysis for simulating fuel reactor in chemical looping combustor system

The greenhouse problem has a significant effect on our communities such as,health and climate.Carbon dioxide is one of the main gases that cause global warming.Therefore,CO2 capture techniques have been the focus of attention these days.The chemical looping combustion technique adopted the air reactor and fuel reactor to recycle heat energy.This study presents a numerical and experimental investigation on a fuel reactor in chemical looping combustor(CLC)system.The present numerical model is introduced by the kinetic theory of granular flow and coupled with gas–solid flow with chemical reactions to simulate the combustion of solids in the CLC.The k–εturbulent model was used to model the gas phase and the particle phase.The developed model simplify the prediction of flow patterns,particle velocities,gas velocities,and composition profiles of gas products and the distribution of heterogeneous reaction rates under the same operating conditions.The predicted and experimental results were compared according to the basis of determination coefficient(R2).In addition the results showed that there is a good agreement between the predicted and experimental data.The value of(R2)for CO,CO2 and CH4 was 0.959,0.925 and 0.969 respectively.This shows that the present model is a promising simulation for solid particle combustion and gives the power direction for the design and optimization of the CLC systems.

Hydrogen production via chemical looping reforming of coke oven gas

Coke oven gas(COG)is one of the most important by-products in steel industry,and the conversion of COG to value-added products has attracted much attention from both economic and environmental views.In this work,we use the chemical looping reforming technology to produce pure H_(2) from COG.A series of La1-xSrxFeO_(3)(x?0,0.2,0.3,0.4,0.5,0.6)perovskite oxides were prepared as oxygen carriers for this purpose.The reduction behaviors of La1-xSrxFeO_(3) perovskite by different reducing gases(H_(2),CO,CH4 and the mixed gases)are investigated to discuss the competition effect of different components in COG for reacting with the oxygen carriers.The results show that reduction temperatures of H_(2) and CO are much lower than that of CH4,and high temperatures(>800℃)are requested for selective oxidation of methane to syngas.The co-existence of CO and H_(2) shows weak effect on the equilibrium of methane conversion at high temperatures,but the oxidation of methane to syngas can inhibit the consumption of CO and H_(2).The doping of suitable amounts of Sr in LaFeO_(3) perovskite(e.g.,La0.5Sr0.5FeO_(3))significantly promotes the activity for selective oxidation of methane to syngas and inhibits the formation of carbon deposition,obtaining both high methane conversion in the COG oxidation step and high hydrogen yield in the water splitting step.The La0.5Sr0.5FeO_(3) shows the highest methane conversion(67.82%),hydrogen yield(3.34 mmol g^(-1))and hydrogen purity(99.85%).The hydrogen yield in water splitting step is treble as high as the hydrogen consumption in reduction step.These results reveal that chemical looping reforming of COG to produce pure H_(2) is feasible,and an O_(2)-assistant chemical looping reforming process can further improves the redox stability of oxygen carrier.

Experimental and mechanistic study on chemical looping combustion of caking coal

Under high-temperature batch fluidized bed conditions and by employing juye coal as the raw material,the present study determined the effects of the bed material,temperature,OC/C ratio,steam flow and oxygen carrier cycle on the chemical looping combustion of coal.In addition,the variations taking place in the surface functional groups of coal under different reaction times were investigated,and the variations achieved by the gas released under the pyrolysis and combustion of Juye coal were analyzed.As revealed from the results,the carbon conversion ratio and rate were elevated significantly,and the volume fraction of the outlet CO_(2)remained more than 92%under the oxygen carriers.The optimized reaction conditions to achieve the chemical looping combustion of Juye coal consisted of a temperature of 900℃,an OC/C ratio of 2,as well as a steam flow rate of 0.5 g·min^(-1).When the coal was undergoing the chemical looping combustion,volatiles primarily originated from the pyrolysis of aliphatic-CH_(3)and-CH_(2),and CO and H_(2)were largely generated from the gasification of aromatic carbon.In the CLC process,H_(2)O and CO_(2)began to separate out at 270℃,CH4 and tar began to precipitate at 370℃,and the amount of CO_(2)was continuously elevated with the rise of the temperature.

Syngas production from chemical looping reforming of ethanol over iron-based oxygen carriers: Theoretical analysis and experimental investigation

Chemical looping reforming(CLR)is a recent trend for syngas production,which has several merits compared to the conventional manner.One of the most important issues for CLR is to find low-cost material as oxygen carriers,so iron is a promising candidate.This paper contributes to testing the thermodynamic ability of iron-based oxygen carrier for chemical looping reforming of ethanol(CLRE).Iron thermodynamically investigated in temperature 100–1300℃and excess oxygen number(φ)0–4.It was found that the temperature andφhave an apparent effect on the gaseous composition produced from the process.Increases in temperature within the range of 100–1300℃enhanced syngas generated and reduced coke formation and CH4.Whereas,increasedφ,particularly at higher temperatures,had also enhanced syngas production as well as reduced coke formation.However,increasingφfor values beyond one had decreased syngas and not significantly reduced coke deposition.Moreover,an experimental investigation was carried out in a fixed bed reactor for more in-depth verification of iron ability as an oxygen carrier through using magnetite ore(mainly Fe3O4).It found that the effect of temperature on syngas production was consistent with that calculated thermodynamically,as syngas increased with raising the temperature through the CLRE.

Energy and economic analysis of a hydrogen and ammonia co-generation system based on double chemical looping

In this work,a model of hydrogen production by double chemical looping is introduced.The efficiency benefit obtained was investigated.The chemical looping hydrogen generation unit is connected in series to the downstream of a chemical looping gasification unit as an additional system for 100 MWh coal gasification,with the function of supplementary combustion to produce hydrogen.Using Aspen Plus software for process simulation,the production of H_(2) and N_(2) in the series system is higher than that in the independent Chemical looping gasification and Chemical looping hydrogen generation systems,and the production of hydrogen is approximately 25.63%and 12.90%higher,respectively;The study found that when the gasification temperature is 900C,steam-carbon ratio is 0.84 and oxygen-carbon ratio is 1.5,the hydrogen production rate of the system was the maximum.At the same time,through heat exchange between logistics,high-pressure steam at 8.010×10^(4) kg·h^(-1) and medium-pressure steam at 1.101×10^(4) kg·h^(-1) are generated,and utility consumption is reduced by 61.58%,with utility costs decreasing by 48.69%.An economic estimation study found that the production cost of ammonia is 108.66 USD(t NH_(3))^(-1).Finally,cost of equipment is the main factors influencing ammonia production cost were proposed by sensitivity analysis.

NO removal performance of CO in carbonation stage of calcium looping for CO_(2) capture

Calcium looping realizes CO_(2)capture via the cyclic calcination/carbonation of CaO.The combustion of fuel supplies energy for the calciner.It is unavoidable that some unburned char in the calciner flows into the carbonator,generating CO due to the hypoxic atmosphere in the carbonator.CO can reduce NO in the flue gases from coal-fired power plants.In this work,NO removal performance of CO in the carbonation stage of calcium looping for CO_(2)capture was investigated in a bubbling fluidized bed reactor.The effects of carbonation temperature,CO concentration,CO_(2)capture,type of CaO,number of CO_(2)capture cycles and presence of char on NO removal by CO in carbonation stage of calcium looping were discussed.CaO possesses an efficient catalytic effect on NO removal by CO.High temperature and high CO concentration lead to high NO removal efficiency of CO in the presence of CaO.Taking account of better NO removal and CO_(2)capture,the optimal carbonation temperature is 650℃.The carbonation of CaO reduces the catalytic activity of CaO for NO removal by CO due to the formation of CaCO_(3).Besides,the catalytic performance of CaO on NO removal by CO gradually decreases with the number of CO_(2)capture cycles.This is because the sintering of CaO leads to the fusion of CaO grains and blockage of pores in CaO,hindering the diffusion of NO and CO.The high CaO content and porous structure of calcium-based sorbents are beneficial for NO removal by CO.The presence of char promotes NO removal by CO in the carbonator.CO_(2)/NO removal efficiencies can reach above 90%.The efficient simultaneous NO and CO_(2)removal by CO and CaO in the carbonation step of the calcium looping seems promising.

A comparative process simulation study of Ca-Cu looping involving post-combustion CO2 capture

This work presents a simulation study of several Ca-Cu looping variants with CO(2)capture,aiming at both parameter optimization and exergy analysis of these Ca-Cu looping systems.Three kinds of Ca-Cu looping are considered:(1)carbonation-calcination/reduction-oxidation;(2)carbonation-oxidation-calcination/reduction and (3)carbona tion/oxidation-calcination/reduction.A conventional Ca looping is also simulated for comparison.The influences of the calcination temperature on the mole fractions of CO(2)and CaO at the calciner outlet,the CaCO3 flow rate on the carbonator performance and the Cu/Ca ratio on the calciner performance are analyzed.The second kind of Ca-Cu looping has the highest carbonation conversion.At 1×10^5 Pa and 820℃,complete decomposition of CaCO3 can be achieved in three Ca-Cu looping systems,while the operation condition of 1×10^5 Pa,840℃is required for the conventional Ca looping system.Furthermore,the Cu/Ca molar ratio of 5.13-5.19 is required for the Ca-Cu looping.Exergy analyses show that the maximum exergy destruction occurs in the calciner for the four modes and the second Ca-Cu looping system(i.e.,carbonation-oxidation-calcination/reduction)performs the highest exergy efficiency,up to 65.04%,which is about 30%higher than that of the conventional Ca looping.

Layered Mg-Al spinel supported Ce-Fe-Zr-O oxygen carriers for chemical looping reforming

A series of layered Mg-Al spinel supported Ce-Fe-Zr-O oxygen carriers were prepared for co-production of syngas and pure hydrogen via chemical looping steam reforming(CLSR).The presence of magnesium-aluminum layered double oxides(Mg Al-LDO)significantly increases the specific surface area of the mixed oxides,reduces the particle size of CeO2-based solid solution and promotes the dispersion of free Fe2O3.When reacting with methane,Mg Al-LDO supported oxygen carrier shows much lower temperature for methane oxidation than the pure CeFe-Zr-O sample,indicating enhanced low-temperature reactivity.Among different Ce-Fe-Zr-O(x)/Mg Al-LDO samples,the Ce-Fe-Zr-O(40 wt%)/Mg Al-LDO sample shows the best performance for the selective oxidation of methane to syngas and the H2 production by water splitting.After a long period of high temperature redox experiment,the Ce-Fe-Zr-O(40 wt%)/Mg Al-LDO oxygen carrier still shows high activity for syngas generation.The comparison on the morphology of the fresh and cycled oxygen carriers indicates that the Mg-Al spinel support still forms a stable skeleton structure with high dispersion of active components on the surface after the long-term cycling,which contributes to excellent redox stability of the Ce-Fe-Zr-O(40 wt%)/Mg Al-LDO oxygen carrier.