Effect of heat treatment on microstructure and mechanical properties of Ti-containing low alloy martensitic wear-resistant steel

Effects of quenching temperature and cooling conditions(water cooling and 10%NaCl cooling)on microstructure and mechanical properties of a 0.2%Ti low alloy martensitic wear-resistant steel used for die casting ejector plate were investigated.The results show that lath martensite can be obtained after austenitizing in the range of 860-980℃and then water cooling.With an increase in austenitizing temperature,the precipitate content gradually decreases.The precipitates are mainly composed of TiC and Ti4C2S2,and their total content is between 1.15wt.%and 1.64wt.%.The precipitate phase concentration by water-cooling is higher than that by10%NaCl cooling due to the lower cooling rate of water cooling.As the austeniting temperature increases,the hardness and tensile strength of both water cooled and 10%NaCl cooled steels firstly increase and then decrease.The experimental steel exhibits the best comprehensive mechanical properties after being austenitized at 900℃,cooled by 10%NaCl,and then tempered at 200℃.Its hardness,ultimate tensile strength,and wear rate reach551.4 HBW,1,438.2 MPa,and 0.48×10^(-2)mg·m^(-1),respectively.

Influence of mill scale and rust layer on the corrosion resistance of low-alloy steel in simulated concrete pore solution

Electrochemical impedance spectroscopy, cyclic potentiodynamic polarization measurements, and scanning electron microscopy in conjunction with energy-dispersive X-ray spectroscopy were used to investigate the influence of mill scale and rust layer on the passivation capability and chloride-induced corrosion behaviors of conventional low-carbon（LC） steel and low-alloy（LA） steel in simulated concrete pore solution. The results show that mill scale exerts different influences on the corrosion resistance of both steels at various electrochemical stages. We propose that the high long-term corrosion resistance of LA steel is mainly achieved through the synergistic effect of a gradually formed compact, adherent and well-distributed Cr-enriched inner rust layer and the physical barrier protection effect of mill scale.

Recent progress in third-generation low alloy steels developed under M^3 microstructure control

During the past thirty years, two generations of low alloy steels(ferrite/pearlite followed by bainite/martensite) have been developed and widely used in structural applications. The third-generation of low alloy steels is expected to achieve high strength and improved ductility and toughness, while satisfying the new demands for weight reduction, greenness, and safety. This paper reviews recent progress in the development of third-generation low alloy steels with an M^3 microstructure, namely, microstructures with multi-phase, meta-stable austenite, and multi-scale precipitates. The review summarizes the alloy designs and processing routes of microstructure control, and the mechanical properties of the alloys.The stabilization of retained austenite in low alloy steels is especially emphasized. Multi-scale nano-precipitates, including carbides of microalloying elements and Cu-rich precipitates obtained in third-generation low alloy steels, are then introduced. The structure–property relationships of third-generation alloys are also discussed. Finally, the promises and challenges to future applications are explored.

Characterization of Rust Layer Formed on Low Alloy Steel Exposed in Marine Atmosphere

The iron rust phases formed on low alloy steels containing different quantities of Cr element have been characterized using EPMA, Raman spectroscopy, TEM, optical microscopy etc. The ion selective properties of synthesized rust films with the same phase constituent as the atmospheric corrosion products were investigated using self-made apparatus. The results showed that corrosion loss of steels exposed in marine atmosphere decreased rapidly as the Cr content of the steel was increased. Cr-containing steels were covered by a uniform compacted rust layer composed of fine particles with an average diameter of several nanometers. Inner rust layer of Cr-containing steel (2 mass fraction) was composed of a-CrxFe1-xOOH, with Cr content of about 5 mass fraction. Such rust layer showed cation selective property, and could depress the penetration of Cl- to contact substrate steel directly.

Data-mining and atmospheric corrosion resistance evaluation of Sn-and Sb-additional low alloy steel based on big data technology

Machine-learning and big data are among the latest approaches in corrosion research.The biggest challenge in corrosion research is to accurately predict how materials will degrade in a given environment.Corrosion big data is the application of mathematical methods to huge amounts of data to find correlations and infer probabilities.It is possible to use corrosion big data method to distinguish the influence of the minimal changes of alloying elements and small differences in microstructure on corrosion resistance of low alloy steels.In this research,corrosion big data evaluation methods and machine learning were used to study the effect of Sb and Sn,as well as environmental factors on the corrosion behavior of low alloy steels.Results depict corrosion big data method can accurately identify the influence of various factors on corrosion resistance of low alloy and is an effective and promising way in corrosion research.

ISOCHRONOUS STRESS-STRAIN CURVES OF LOW ALLOY STEEL CROSS-WELD-SPECIMEN AT HIGH TEMPERATURE

In this work, a parametric approach is presented and utilized to determine the creep properties of weldments; then the model of creep strain for cross weld specimen is given. On the basis of the experimental results, attempt has been made to establish equations of the isochronous stress-strain for weld joint that can predict the function of loading and service time in use of the creep data of base metal and weld metal.

A method to study interface diffusion of arsenic into a Nb-Ti microalloyed low carbon steel

A novel diffusion couple method was used to investigate the interface diffusion of arsenic into a Nb-Ti microalloyed low carbon steel and its effects on phase transformation at the interface. It is discovered that the content of arsenic has great effect on grain growth and phase transformation at high temperature. When the arsenic content is no more than lwt%, there is no obvious grain growth and no obvious ferrite transitional region formed at the diffusion interface. However, when the arsenic content is no less than 5wt%, the grain grows very rapidly. In addition, the arsenic-enriched ferrite transitional layer forms at the diffusion interface in the hot-rolling process, which results from a slower diffusion rate of arsenic atoms than that of carbon in ferrite.

Microstructure and mechanical properties of high-strength low alloy steel by wire and arc additive manufacturing

A high-building multi-directional pipe joint(HBMDPJ)was fabricated by wire and arc additive manufacturing using high-strength low-alloy(HSLA)steel.The microstructure characteristics and transformation were observed and analyzed.The results show that the forming part includes four regions.The solidification zone solidifies as typical columnar crystals from a molten pool.The complete austenitizing zone forms from the solidification zone heated to a temperature greater than 1100℃,and the typical columnar crystals in this zone are difficult to observe.The partial austenitizing zone forms from the completely austenite zone heated between Ac1(austenite transition temperature)and1100℃,which is mainly equiaxed grains.After several thermal cycles,the partial austenitizing zone transforms to the tempering zone,which consistes of fully equiaxed grains.From the solidification zone to the tempering zone,the average grain size decreases from 75 to20μm.The mechanical properties of HBMDPJ satisfies the requirement for the intended application.

Influence of chromium on the initial corrosion behavior of low alloy steels in the CO_2–O_2–H_2S–SO_2 wet–dry corrosion environment of cargo oil tankers

The influence of Cr on the initial corrosion behavior of low-alloy steels exposed to a CO2–O2–H2S–SO2 wet–dry corrosion environment was investigated using weight-loss measurements, scanning electron microscopy, N2 adsorption tests, X-ray diffraction analysis, and electrochemical impedance spectroscopy. The results show that the corrosion rate increases with increasing Cr content in samples subjected to corrosion for 21 d. However, the rust grain size decreases, its specific surface area increases, and it becomes more compact and denser with increasing Cr content, which indicates the enhanced protectivity of the rust. The results of charge transfer resistance(Rct) calculations indicate that higher Cr contents can accelerate the corrosion during the first 7 d and promote the formation of the enhanced protective inner rust after 14 d; the formed protective inner rust is responsible for the greater corrosion resistance during long-term exposure.

Numerical simulation of residual stress and deformation for submerged arc welding of Q690D high strength low alloy steel thick plate

The finite element simulation software SYSWELD is used to numerically simulate the temperature field,residual stress field,and welding deformation of Q690D thick plate multi-layer and multi-pass welding under different welding heat input and groove angles.The simulation results show that as the welding heat input increases,the peak temperature during the welding process is higher,and the residual stress increases,they are all between 330–340 MPa,and the residual stress is concentrated in the area near the weld.The hole-drilling method is used to measure the actual welding residual stress,and the measured data is in good agreement with the simulated value.The type of post-welding deformation is angular deformation,and as the welding heat input increases,the maximum deformation also increases.It shows smaller residual stress and deformation when the groove angle is 40°under the same heat input.In engineering applications,under the premise of guaranteeing welding quality,smaller heat input and 40°groove angle should be used.

Effects of Mo Composites on the Corrosion Behaviors of Low Alloy Steel

By using electrochemical and weight loss methods, the effect of MoO42-on the corrosion behaviors of low alloy steel was investigated in the 55%LiBr＋0.07 mol/L LiOH solution at high temperature. The results show that MoO42 , being an anodic inhibitor, would form a passive film rapidly and impede both anodic and cathodic reactions. Moreover, Na2MoO4 effectively prevents corrosion in 55%LiBr＋0.07 mol/L LiOH solution when its concentration is higher than 200 mg/L. Some elements of alloy, such as chromium and nickel, may cause the widening of passive potential region and the decrease of passive density, which indicates that the corrosion resistance increases. AES analysis shows that molybdenum participates in forming a protection film. The synergistic effect between chromium and molybdenum induces Cr-steel to be in passive state in lower Na2MoO4 concentration.

Transformation Kinetics of Pearlite to Austenite in Low Alloy Steel Containing Rare Earth

The phase transformation kinetics of pearlite to austenite in low alloy steel containing RE was studied by the methods of DSC. The results show that the apparent transformation activation energy of pearlite to austenite in the low alloy steel is 1141.04 kJ·mol -1, and the transformation activation energy of pearlite to austenite decreases with increasing of the volume fraction of transformation phase. Through which, the relationship curve between the volume fraction of transformation phase and the temperature were drawn.

CORROSION BEHAVIORS OF THE EXPOSED SIDE AND UNDERSIDE OF LOW ALLOY WEATHERING STEEL IN QINGDAO AND WANNING FOR 18 MONTHS

For 18 months, a newly developed low alloy weathering steel has been exposed in two coastal sites （Qingdao in the north China, Wanning in the south China）. The different corrosion behaviors of the exposed side and the underside of the samples were characterized by X-ray diffraetion （XRD）, polarization curve, electrochemical impedance spectroscopy （EIS）, scanning electron microscopy （SEM）, and N2 adsorption approach. It was found that the samples exhibited higher corrosion rate in Wanning than that in Qingdao. The underside of the samples corrodes more seriously than the exposed side in Qingdao, whereas the result in Wanning is just the reverse. The protection performance of rust layers mainly depends on its compactness and the enrichment of Cu and Cr is a secondary causation. The different compactness of rust layers in the exposed side and the underside originates from different corrosion conditions of the two sides.

Effect of Si Content on Mechanical Properties of a Mo and V Free Low Alloy Cast Steel for Automobile Cold Pressing Die

The effects of Si content on combinations of important properties such as hardness, hardenability, and weldability in addition to strength increment were systematically investigated to develop a Mo and V free low alloy cast steel for automobile cold pressing die insert. For the evaluation of the applicability as the die insert, the mechanical properties were measured after spheroidization annealing （SA）, quenching and tempering （Q/T）, and flame hardening （FH） treatments, respectively. The developed 0.8%-1.6%Si containing Mo and V free alloy cast steels showed excellent matrix strengthening effect, hardenability, and weldability, fulfilling the industrial criterion of the mechanical properties for the die insert.

Corrosion behavior and corrosion products of a low-alloy weathering steel in Qingdao and Wanning

A newly developed low-alloy weathering steel has been exposed in two coastal sites （Qingdao in the north, Wanning in the south） in China for one year. The samples in Wanning corroded far more seriously than those in Qingdao. The rust layer formed on the steel was analyzed by X-ray diffraction （XRD）, scanning electron microscopy （SEM）, N2 adsorption approach, polarization curves, and electrochemical impedance spectroscopy （EIS）. The rust formed in Qingdao contains more X-ray amorphous compounds and is more compact than that formed in Wanning. Cr and Cu are enriched in the rust layer near the steel matrix, and the phenomenon is more obvious in Qingdao than in Wanning. The rust layer formed in Qingdao suppresses the anodic and cathodic reaction more remarkably than that formed in Wanning does. The rust layer formed in Qingdao possesses a higher ability to block the permeation of chloride ions than that formed in Wanning does.

Susceptibility of two types of low-alloy hull steels to pit initiation

Four low-alloy hull steels with different alloy elements were selected. Theirsusceptibility to pitting corrosion was compared by means of electrochemical polarization test. Theinclusions in the steels and their pitting corrosion characteristics were studied by an electronprobe micro-analyzer (EPMA). The results indicate that some inclusions are the main sources ofpitting corrosion. The susceptibility of nickel-chromium steel to pit initiation is less than thatof manganese steel. Under the same conditions, nickel-chromium steel is easier to passivate thanmanganese steel, and the passive films on nickel-chromium steel surface are more stable than that onmanganese steel. In low-alloy steels, the higher the contents of nickel and chromium, the lower thecritical passive pH value. In the same kind of steel, multi-phase inclusions containing sulfide areeasier to initiate pitting corrosion than other inclusions.

Abrasive Wear Characteristics of Carbon and Low Alloy Steels for Better Performance of Farm Implements

The low stress abrasion behaviours of heat treated mild, medium carbon and high C - low Cr steels, which are generally used in making farm implements, have been investigated. The simple heat treatment greatly improves the hardness, tensile strength and abrasion resistance of medium carbon and high C - low Cr steels. The results indicate that the material removal during abrasion is controlled by a number of factors, such as hardness, chemical composition, microstructure and heat treatment conditions. The conclusion is that the heat treated high C - low Cr steel and mild steel carburized by using coaltar pitch provide the best hardness and abrasion resistance and thus appear to be the most suitable materials for making agricultural tools.

Dual Phase Heat Treatment of Low-Alloy Steel

Dual phase heat treatment is an economical and effective way for improving the properties of low carbon steels and low-alloy steel materials. In this paper, the microstructures and mechanical properties of 20MnSi steel treated by different dual phase heat treatment have been studied. The results show that dual phase heat treatment with pre-quenching technique and then heating from room temperature to the critical zone can achieve finer and more homogeneous microstructure than that with pre-normalizing technique and then cooling from austenite zone to the critical zone. Among all factors affecting dual phase heat treatment, quenching temperature at the critical zone and tempering temperature play an important part in mechanical properties. Using proper dual phase heat treatment technique with computer optimized parameters, the yield strength, the elongation and impact toughness of 20MnSi can reach 860 MPa, 16% and 207 MPa respectively.

Carbon Equivalent Fundamentals in Evaluating the Weldability of Microalloy and Low Alloy Steels

Understanding the weldability of steel in relation to the use of carbon equivalent is very necessary for the welding industry. The study was poised to unearth the fundamentals of carbon equivalent as applied in evaluating the weldability of steel. The study used a two-stage design approach to address the problem of carbon equivalence weldability of steel, thus, survey and experimental. Two different steels were tested to ascertain their chemical composition which could inform carbon equivalent calculation, and the results revealed microalloy and low alloy steels respectively. In subjecting the microalloy steel to carbon equivalent analyses of the AWS and IIW coefficients;revealed a value (CEV) = 0.11 each, suggesting that this microalloy steel has excellent weldability;no preheating is required. A successful welding operation on this steel does not depend on preheating. Also, the average results of the low alloy steel revealed a value (CEV) = 0.37 and 0.32 respectively, suggesting that this type of steel has very good weldability and may require to preheat. It is recommended that welders have a general idea about the weldability of steel with regard to carbon equivalent calculation. In addition, they should understand the chemical compositions of steels they are dealing with.

Influence of soaking time in deep cryogenic treatment on the microstructure and mechanical properties of low-alloy medium-carbon HY-TUF steel

The influence of soaking time in deep cryogenic treatment on the tensile and impact properties of low-alloy medium-carbon HY-TUF steel was investigated in this study. Microstructural studies based on phase distribution mapping by electron backscatter diffraction show that the deep cryogenic process causes a decrease in the content of retained austenite and an increase in the volume fraction of η-carbide with increasing soaking time up to 48 h. The decrease in the content of retained austenite from ~1.23vol% to 0.48vol% suggests an isothermal martensitic transformation at 77 K. The η-type precipitates formed in deep cryogenic-treated martensite over 48 h have the Hirotsu and Nagakura orientation relation with the martensitic matrix. Furthermore, a high coherency between η-carbide and the martensitic matrix is observed by high-resolution transmission electron microscopy. The variations in macrohardness, yield strength, ultimate tensile strength, and ductility with soaking time in the deep cryogenic process show a peak/plateau trend.