Wavelength-interval switchable Brillouin–Raman random fiber laser through Brillouin pump manipulation

A wavelength-interval switchable Brillouin–Raman random fiber laser(BRRFL) based on Brillouin pump(BP) manipulation is proposed in this paper. The proposed wavelength-interval switchable BRRFL has a full-open cavity configuration, featuring multiwavelength output with wavelength interval of double Brillouin frequency shifts. Through simultaneously injecting the BP light and its first-order stimulated Brillouin-scattered light into the cavity, the laser output exhibits a wavelength interval of single Brillouin frequency shift. The wavelength-interval switching effect can be manipulated by controlling the power of the first-order stimulated Brillouin scattering light. The experimental results show the multiwavelength output can be switched between double Brillouin frequency shift multiwavelength emission with a broad bandwidth of approximately 60 nm and single Brillouin frequency shift multiwavelength emission of 44 nm. The flexible optically controlled random fiber laser with switchable wavelength interval makes it useful for a wide range of applications and holds significant potential in the field of wavelength-division multiplexing optical communication.

Numerical design of an efficient Ho^(3+)-doped InF3 fiber laser at~3.2μm

In this work,we theoretically unlock the potential of Ho^(3+)-doped InF3 fiber for efficient~3.2μm laser generation(from the ^(5)F_(4),^(5)S_(2)→^(5)F_(5) transition),by employing a novel dual-wavelength pumping scheme at 1150 nm and 980 nm,for the first time.Under clad-coupled 1150 nm pumping of 5 W,~3.2μm power of 3.6 W has been predicted with the optical-to-optical efficiency of 14.4%.Further efficient power scaling,however,is blocked by the output saturation with 980 nm pumping.To alleviate this behavior,the cascaded ^(5)I_(5)→^(5)I_(6) transition,targeting~3.9μm,has been activated simultaneously,therefore accelerating the population circulation between the laser upper level ^(5)F_(4),^(5)S_(2) and long-lived ^(5)I_(6) level under 980 nm pumping.As a result,enhanced~3.2μm power of 4.68 W has been obtained with optical-to-optical efficiency of 15.6%.Meanwhile the~3.9μm laser,yielding power of 2.76 W with optical-to-optical efficiency of 9.2%,is theoretically achievable as well with a moderate heat load,of which the performance is even better than the prior experimentally and theoretically reported Ho^(3+)-doped InF3 fiber lasers emitting at~3.9μm alone.This work demonstrates a versatile platform for laser generation at~3.2μm and~3.9μm,thus providing the new opportunities for many potential applications,e.g.,polymer processing,infrared countermeasures,and free-space communications.

Widely-wavelength-tunable brillouin fiber laser with improved optical signal-to-noise ratio based on parity-time symmetric and saturable absorption effect

A widely-wavelength-tunable Brillouin fiber laser(BFL)with improved optical signal-to-noise ratio(OSNR)based on parity-time(PT)symmetric and saturable absorption(SA)effect is present.This novel BFL realizes PT symmetry and SA effect through polarization-maintaining erbium-doped fiber(PM-EDF)Sagnac loop,which is composed of a PM-EDF,a coupler and two polarization controllers(PCs).By using the inherent birefringence characteristic of PM-EDF,two feedback loops in orthogonal polarization state are formed when the Strokes signal in injected.One of these loops provides gain in the clockwise direction with in the Sagnac loop,while the other loop generates loss in the counterclockwise direction.By adjusting the PCs to control the polarization state of the PM-EDF,a single-longitudinal-mode(SLM)BFL can be achieved,as the PT symmetry is broken when the SA participating stimulated Brillouin scattering(SBS)gain and loss are well-matched and the gain surpasses the coupling coefficient.Compared to previous BFLs,the proposed BFL has a more streamlined structure and a wider wavelength tunable range,at the same time,it is not being limited by the bandwidth of the erbium-doped fiber amplifier while still maintaining narrow linewidth SLM output.Additionally,thanks to SA effect of the PM-EDF,the PT symmetric SBS gain contract is enhanced,resulting in a higher optical signal-to-noise(OSNR).The experimental results show that the laser has a wide tunable range of 1526.088 nm to 1565.498 nm,an improved OSNR of 77 dB,and a fine linewidth as small as 140.5 Hz.

Internal phase control of fiber laser array based on photodetector array

Coherent beam combining(CBC) of fiber laser array is a promising technique to realize high output power while maintaining near diffraction-limited beam quality. To implement CBC, an appropriate phase control feedback structure should be established to realize phase-locking. In this paper, an innovative internal active phase control CBC fiber laser array based on photodetector array is proposed. The dynamic phase noises of the laser amplifiers are compensated before being emitted into free space. And the static phase difference compensation of emitting laser array is realized by interference measurement based on photodetector array. The principle of the technique is illustrated and corresponding simulations are carried out, and a CBC system with four laser channels is built to verify the technique. When the phase controllers are turned on, the phase deviation of the laser array is less than λ/20, and ~ 95% fringe contrast of the irradiation distribution is obtained. The technique proposed in this paper could provide a reference for the system design of a massive high-power CBC system.

Imaging through scattering layers using a near-infrared low-spatial-coherence fiber random laser

Optical memory effect-based speckle-correlated technology has been developed for reconstructing hidden objectsfrom disordered speckle patterns,achieving imaging through scattering layers.However,the lighting efficiency and fieldof view of existing speckle-correlated imaging systems are limited.Here,a near-infrared low spatial coherence fiberrandom laser illumination method is proposed to address the above limitations.Through the utilization of random Rayleighscattering within dispersion-shifted fibers to provide feedback,coupled with stimulated Raman scattering for amplification,a near-infrared fiber random laser exhibiting a high spectral density and extremely low spatial coherence is generated.Based on the designed fiber random laser,speckle-correlated imaging through scattering layers is achieved,with highlighting efficiency and a large imaging field of view.This work improves the performance of speckle-correlated imagingand enriches the research on imaging through scattering medium.

Broadband bidirectional Brillouin–Raman random fiber laser with ultra-narrow linewidth

We present a Brillouin–Raman random fiber laser(BRRFL)with full-open linear cavity structure to generate broadband Brillouin frequency comb(BFC)with double Brillouin-frequency-shift spacing.The incorporation of a regeneration portion consisting of an erbium-doped fiber and a single-mode fiber enables the generation of broadband BFC.The dynamics of broadband BFC generation changing with the pump power(EDF and Raman)and Brillouin pump(BP)wavelength are investigated in detail,respectively.Under suitable conditions,the bidirectional BRRFL proposed can produce a flatamplitude BFC with 40.7-nm bandwidth ranging from 1531 nm to 1571.7 nm,and built-in 242-order Brillouin Stokes lines(BSLs)with double Brillouin-frequency-shift spacing.Moreover,the linewidth of single BSL is experimentally measured to be about 2.5 kHz.The broadband bidirectional narrow-linewidth BRRFL has great potential applications in optical communication,optical sensing,spectral measurement,and so on.

Comprehensive analysis of pure-quartic soliton dynamics in a passively mode-locked fiber laser

The understanding of soliton dynamics promotes the development of ultrafast laser technology. High-energy purequartic solitons(PQSs) have gradually become a hotspot in recent years. Herein, we numerically study the influence of the gain bandwidth, saturation power, small-signal gain, and output coupler on PQS dynamics in passively mode-locked fiber lasers. The results show that the above four parameters can affect PQS dynamics. Pulsating PQSs occur as we alter the other three parameters when the gain bandwidth is 50 nm. Meanwhile, PQSs evolve from pulsating to erupting and then to splitting as the other three parameters are altered when the gain bandwidth is 10 nm, which can be attributed to the existence of the spectral filtering effect and intra-cavity fourth-order dispersion. These findings provide new insights into PQS dynamics in passively mode-locked fiber lasers.

Single-frequency linearly polarized Q-switched fiber laser based on Nb_(2)GeTe_(4)saturable absorber

We report a single-frequency linearly polarized Q-switched fiber laser based on an Nb_(2)GeTe_(4)saturable absorber(SA).The Nb_(2)GeTe_(4)SA triggers passive Q-switching of the laser,and an un-pumped Yb-doped fiber together with a 0.08-nmbandwidth polarization-maintaining fiber Bragg grating(FBG)acts as an ultra-narrow bandwidth filter to realize singlelongitudinal-mode(SLM)oscillation.The devices used in the laser are all kept polarized,so as to ensure linearly polarized laser output.Stable SLM linearly polarized Q-switching operation at 1064.6 nm is successfully achieved,producing a laser with a shortest pulse width of 1.36μs,a linewidth of 28.4 MHz,a repetition rate of 28.3 kHz-95.9 kHz,and a polarization extinction ratio of about 30 dB.It is believed that the single-frequency linearly polarized pulsed fiber laser studied in this paper has great application value in gravitational wave detection,beam combining,nonlinear frequency conversion,and other fields.

Real-time observation of soliton pulsation in net normal-dispersion dissipative soliton fiber laser

We present experimental observations of soliton pulsations in the net normal-dispersion fiber laser by using the dispersive Fourier transform(DFT) technique. According to the pulsating characteristics, the soliton pulsations are classified as visible and invisible soliton pulsations. The visible soliton pulsation is converted from single-into dual-soliton pulsation with the common characteristics of energy oscillation and bandwidth breathing. The invisible soliton pulsation undergoes periodic variation in the spectral profile and peak power but remains invariable in pulse energy. The reason for invisible soliton pulsation behavior is periodic oscillation of the pulse inside the soliton molecule. These results could be helpful in deepening our understanding of the soliton pulsation phenomena.

A kind of multiwavelength erbium-doped fiber laser based on Lyot filter

A multiwavelength tunable ring-cavity erbium-doped fiber laser(EDFL)based on a Lyot filter was presented.For the proposed Lyot filter,a comb filter consisting of an EDF-polarization-maintaining fiber(EDF-PMF),a polarization controller(PC),and a circulator with four ports was used to suppress the mode competition.The light transmission direction was guaranteed by the circulator.For the proposed fiber laser,tunable single,dual,triple,quadruple,quintuple,sextuple,and septuple wavelengths were realized.A single-wavelength laser output with an optical signal-to-noise ratio(SNR)of up to30.56 dB was realized,and a tuning range of 1590.54 nm to 1599.54 nm was achieved by tuning the PC.The stability of the single,dual,triple,and quadruple-wavelength center power fluctuations was less than 0.05 dB,0.98 dB,5.07 dB,and7.71 dB respectively.When the laser was operated in the multiwavelength condition,the SNR was more than 20.97 dB.The proposed erbium-doped fiber laser is suitable for fiber-sensing system applications.

Antimonene-based saturable absorber for a soliton mode-locked and Q-switched fiber laser in the 2 μm wavelength region

We demonstrate antimonene as a saturable absorber(SA) to generate an ultrafast mode-locked and Q-switched laser in the 2 μm wavelength region. The two antimonene-based SAs were prepared and inserted separately in a thulium–holmiumdoped fiber laser to produce the pulsed laser. Antimonene was coated onto a tapered fiber to generate soliton mode-locked pulses and used in thin-film form for the generation of Q-switched pulses. The mode-locking was stable within a pump power of 267 m W–511 m W, and the laser operated at a central wavelength of 1897.4 nm. The mode-locked laser had a pulse width of 1.3 ps and a repetition rate of 12.6 MHz, with a signal-to-noise ratio of 64 d B. Q-switched laser operation was stable at a wavelength of 1890.1 nm within a pump power of 312 m W–381 m W. With the increase in pump power from 312 m W to 381 m W, the repetition rate increased to a maximum of 56.63 k Hz and the pulse width decreased to a minimum value of 2.85 μs. Wide-range tunability of the Q-switched laser was also realized within the wavelength range of1882 nm–1936 nm.

Thulium fiber laser lithotripsy:Is it living up to the hype?

Objective:The holmium:yttrium-aluminium-garnet laser(Ho:YAG)has been the gold standard for laser lithotripsy over the last three decades.After demonstrating good in vitro efficacy,the thulium fiber laser(TFL)has been recently released in the market and the initial clinical results are encouraging.This article aims to review the main technology differences between the Ho:YAG laser and the TFL,discuss the initial clinical results with the TFL as well as the optimal settings for TFL lithotripsy.Methods:We reviewed the literature focusing on the technological aspects of the Ho:YAG laser and TFL as well as the results of in vitro and in vivo studies comparing both technologies.Results:In vitro studies show a technical superiority of TFL compared to the Ho:YAG laser and encouraging results have been demonstrated in clinical practice.However,as TFL is a new technology,limited studies are currently available,and the optimal settings for lithotripsy are not yet established.Conclusion:TFL has the potential to be an alternative to the Ho:YAG laser,but more reports are still needed to determine the optimal laser for lithotripsy of urinary tract stones when considering all parameters including effectiveness,safety,and costs.

Porosity sensitivity of A356 Al alloy during fiber laser welding

In order to decrease the metallurgical porosity and keyhole-induced porosity during deep penetration laser welding of Al and its alloys, and increase the mechanical properties of work-piece, the effects of welding parameters such as laser power, welding speed and defocusing value on both kinds of porosities were systemically analyzed respectively, and the shape and fluctuation of plume of the keyhole were observed to reflect the stability of the keyhole. The results show that increasing laser power or decreasing laser spot size can lead to the rising of both number and occupied area of pores in the weld; meanwhile, the plume fluctuates violently over the keyhole, which is always companied with the intense metallic vapor, liquid metal spatter and collapsing in the keyhole, thus more pores are generated in the weld. The porosity in the weld reaches the minimum at welding velocity of 2.0 m/min when laser power is 5 kW and defocusing value is 0.

Stitch welding of Ti-6Al-4V titanium alloy by fiber laser

Stitch welding of plate covered skeleton structure of Ti-6Al-4V titanium alloys has a variety of applications in aerospace vehicle manufacture. The laser stitch welding of Ti-6Al-4V titanium alloys was carried out by a 4 kW ROFIN fiber laser. Influences of laser welding parameters on the macroscopic geometry, porosity, microstructure and mechanical properties of the stitch welded seams were investigated by digital microscope, optical microscope, scanning electron microscope and universal tensile testing machine. The results showed that the three-pipe nozzle with gas flow rate larger than 5 L/min could avoid oxidization, presenting better shielding effect in comparison with the single-pipe nozzle. Porosity formation could be suppressed with the gap between plate and skeleton less than 0.1 mm, while the existing porosity can be reduced with remelting. The maximum shear strength of stitch welding joint with minimal porosity was obtained by employing laser power of 1700 W, welding speed of 1.5 m/min and defocusing distance of ＋8 ram.

227-W output all-fiberized Tm-doped fiber laser at 1908 nm

In this paper, we report that a diode-pumped thulium-doped double clad silica fiber laser can provide powers of up to 227 W at 1908 nm, corresponding to a slope efficiency of 54.3%, and an optical-to-optical efficiency of 51.2%. The output power, to the best of our knowledge, is the highest output at 1908 nm. The beam quality M2 factor is about 1.56. Also discussed in this paper is the dependence of the laser performance on fiber length.

A long-term frequency-stabilized erbium-fiber-laser-based optical frequency comb with an intra-cavity electro-optic modulator

We demonstrate an optical frequency comb based on an erbium-doped-fiber femtosecond laser with the nonlinear polarization evolution scheme. The repetition rate of the laser is about 209 MHz. By controlling an intra-cavity electro- optic modulator and a piezo-transducer, the repetition rate can be stabilized with a high-bandwidth servo in a frequency range of 3 kHz, enabling long-term repetition rate phase-locking. The in-loop frequency stability of repetition rate is about 1.6× 10-13 in an integration time of 1 s, limited by the measurement system; and it is inversely proportional to integration time in the short term. Furthermore, using a common path f-2f interferometer, the carrier envelope offset frequency of the comb is obtained with a signal-to-noise ratio of 40 dB in a 3-MHz resolution bandwidth. Stabilized cartier envelope offset frequency exhibits a deviation of 0.6 mHz in an integration time of 1 s.

Pulse-train nonuniformity in an all-fiber ring laser passively mode-locked by nonlinear polarization rotation

This paper reports the periodic power variation of the pulse-train in a passively mode-locked soliton fiber ring laser. It can obtain either the uniform or nonuniform pulse-train output by simply rotating the polarization controllers. The experimental results show that the pulse-train nonuniformity is caused by the interaction between the nonuniform polarization states of the soliton pulses and the passive polarizer in the cavity.

Generation and evolution of multiple operation states in passively mode-locked thulium-doped fiber laser by using a graphene-covered-microfiber

Using graphene-covered-microfiber （GCM） as a saturable absorber, the generation and evolution of multiple operation states are proposed and demonstrated in passively mode-locked thulium-doped fiber laser. The microfiber was fabricated using the flame brushing method to an interaction length of - 1.2 cm with a waist diameter of -10 μm. Graphene layers were grown on copper foils by chemical vapor deposition and transferred onto the polydimethylsiloxane （PDMS） to form a PDMS/graphene film, which allowed light-graphene interaction via evanescent field. With the increase of the pump power from 1.25 W to 2.15 W, five different lasing regimes, including continuous-wave, conventional soliton mode-locking, multi- soliton mode-locking, a period of transition, and noise-like mode-locking, were achieved in a fiber ring cavity. To the best of our knowledge, it is the first report of the generation and evolution of multiple operation states by covering graphene on the microfiber in the 2-μ.m region. The results demonstrate that GCM can be a promising method for fabricating all fiber SA, and the switchable operation states can provide more portability in complex application domain.

A Review on Fiber Lasers

After a half century of development, fiber laser has evolved from a concept to a great family penetrating into various fields of applications. This paper reviews the history and current development of fiber lasers, with topics covering both continuous wave and short pulse fiber lasers. Important issues such as the major rare earth dopants, fiber laser brightness, polarization effects, clad pumping technology, beam combination, mode locking and pulse shaping are discussed in this paper.

Passively mode-locked erbium-doped fiber laser via a D-shape-fiber-based MoS_2 saturable absorber with a very low nonsaturable loss

We report on the generation of conventional and dissipative solitons in erbium-doped fiber lasers by the evanescent field interaction between the propagating light and a multilayer molybdenum disulfide（MoS_2） thin film. The MoS_2 film is fabricated by depositing the MoS_2 water–ethanol mixture on a D-shape-fiber（DF） repetitively. The measured nonsaturable loss, saturable optical intensity, and the modulation depth of this device are 13.3%, 110 MW/cm^2, and 3.4% respectively.Owing to the very low nonsaturable loss, the laser threshold of conventional soliton is as low as 4.8 mW. The further increase of net cavity dispersion to normal regime, stable dissipation soliton pulse trains with a spectral bandwidth of 11.7 nm and pulse duration of 116 ps are successfully generated. Our experiment demonstrates that the MoS_2-DF device can indeed be used as a high performance saturable absorber for further applications in ultrafast photonics.