A cold method was used to prepare coated sand for application in the selective laser sintering(SLS)process.Tensile strength,loss on ignition,gas evolution,and accuracy of the SLS samples were tested and analyzed,and t...A cold method was used to prepare coated sand for application in the selective laser sintering(SLS)process.Tensile strength,loss on ignition,gas evolution,and accuracy of the SLS samples were tested and analyzed,and the baking process was thoroughly investigated.Compared with coated sand prepared by the hot method,the cold method yields a more uniform and complete resin film on the sand's surface,resulting in enhanced tensile strength and accuracy.Additionally,the cold method requires a lower binder content to meet the same strength requirements,thereby minimizing gas evolution,reducing porosity defects,and ultimately improving casting quality.The coated sand samples prepared through the cold method exhibit superior accuracy,with a size error of within±0.4 mm.In contrast,the coated sand samples prepared by the hot method display a lower accuracy,with an average negative error of 2.1993 mm.The highest tensile strength could be attained by controlling the baking temperature within a suitable range(180-190°C),which can effectively reduce the generation of gas,thus contributing to improved overall performance.展开更多
A mathematical model is developed for simulating the heat transferring behavior in a direct metal laser sintering process. The model considers the thermal phenomena involved in the process, including conduction, radia...A mathematical model is developed for simulating the heat transferring behavior in a direct metal laser sintering process. The model considers the thermal phenomena involved in the process, including conduction, radiation, and convection. A formula for the calculation of the heat conductivity of a sintering system containing solid phase, liquid phase, and gas phase is given. Due to the continuous movement of the laser beam, a local coordinate system centered on the laser beam is used to simplify the analytical calculation. Assuming that it is approximately a Gaussian laser beam, the heat conduction equation is resolved based on the assumption of the thermal insulating boundary conditions and the fixed thermal physical parameters. The FORTRAN language is employed to compile the program to simulate the temperature field in the direct copper powder sintering process. It shows a good agreement with the preliminary experimental results.[KH3/4D]展开更多
Baozhu sand particles with size between 75 μm and 150 μm were coated by resin with the ratio of 1.5 wt.% of sands. Laser sintering experiments were carried out to investigate the effects of laser energy density(E = ...Baozhu sand particles with size between 75 μm and 150 μm were coated by resin with the ratio of 1.5 wt.% of sands. Laser sintering experiments were carried out to investigate the effects of laser energy density(E = P/v), with different laser power(P) and scanning velocity(v), on the dimensional accuracy and tensile strength of sintered parts. The experimental results indicate that with the constant scanning velocity, the tensile strength of sintered samples increases with an increase in laser energy density; while the dimensional accuracy apparently decreases when the laser energy density is larger than 0.032 J·mm-2. When the laser energy density is 0.024 J·mm-2, the tensile strength shows no obvious change; but when the laser energy density is larger than 0.024 J·mm-2, the sample strength is featured by the initial increase and subsequent decrease with simultaneous increase of both laser power and scanning velocity. In this study, the optimal energy density range for laser sintering is 0.024-0.032 J·mm-2. Moreover, samples with the best tensile strength and dimensional accuracy can be obtained when P = 30-40 W and v = 1.5-2.0 m·s-1. Using the optimized laser energy density, laser power and scanning speed, a complex coated sand mould with clear contour and excellent forming accuracy has been successfully fabricated.展开更多
Selective laser sintering (SLS) is a new process to prepare the polystyrene (PS)/Al2O3 nanocomposites. In this paper, with different laser power and other processing parameters unchanged, the morphology, density a...Selective laser sintering (SLS) is a new process to prepare the polystyrene (PS)/Al2O3 nanocomposites. In this paper, with different laser power and other processing parameters unchanged, the morphology, density and mechanical properties of the sintered specimens were investigated. It was found that nano-sized inorganic particles are uniformly located in the PS matrix and the maximum density of the sintered specimens with pure PS powder reaches 1.07 g/cm^3, higher than 1.04 g/cm^3 that of the sintered specimens with mixture powder. Due to strengthening and toughness of the nano-sized Al2O3 inorganic particles, the maximum notched impact strength and tensile strength of the sintered part mixed with nano-sized inorganic particles are improved greatly from 7.5 to 12.1 kJ/m^2 and from 6.5 to 31.2 MPa, respectively, under the same sintering condition.展开更多
Using a special coated sand as the material of the selected laser sintering (SLS), the authors test and investigate the strength change of the test samples in terms of different sintering parameters (scanning speed, l...Using a special coated sand as the material of the selected laser sintering (SLS), the authors test and investigate the strength change of the test samples in terms of different sintering parameters (scanning speed, laser power, sintering thickness, and so on). The characteristics of coated sand hardening by laser beam are analyzed. The sintered mold (or core) for given casting is poured with molten metal.展开更多
Selective laser sintering(SLS),as a kind of additive manufacturing technology,which uses a laser beam to scan and heat powder material layer by layer to form parts(models),is widely used in the field of casting,mainly...Selective laser sintering(SLS),as a kind of additive manufacturing technology,which uses a laser beam to scan and heat powder material layer by layer to form parts(models),is widely used in the field of casting,mainly for preparing casting coated sand cores,investment casting patterns,etc.The SLS technique facilitates rapid casting and shortens the casting production periods by eliminating mold preparation.In this study,we reached conclusions for the basic principles and characteristics of SLS methods,and focused on the research status,key technology and development trend of SLS in the fields of forming coated sand-casting molds and investment casting patterns.展开更多
Polymers are widely used materials in aerospace,automotive,construction,medical devices and pharmaceuticals.Polymers are being promoted rapidly due to their ease of manufacturing and improved material properties.Resea...Polymers are widely used materials in aerospace,automotive,construction,medical devices and pharmaceuticals.Polymers are being promoted rapidly due to their ease of manufacturing and improved material properties.Research on polymer processing technology should be paid more attention to due to the increasing demand for polymer applications.Selective laser sintering(SLS)uses a laser to sinter powdered materials(typical polyamide),and it is one of the critical additive manufacturing(AM)techniques of polymer.It irradiates the laser beam on the defined areas by a computer-aided design three-dimensional(3D)model to bind the material together to create a designed 3D solid structure.SLS has many advantages,such as no support structures and excellent mechanical properties resembling injection moulded parts compared with other AM methods.However,the ability of SLS to process polymers is still affected by some defects,such as the porous structure and limited available types of SLS polymers.Therefore,this article reviews the current state-of-the-art SLS of polymers,including the fundamental principles in this technique,the SLS developments of typical polymers,and the essential process parameters in SLS.Furthermore,the applications of SLS are focused,and the conclusions and perspectives are discussed.展开更多
In the present work,a study is made to investigate the effects of process parameters,namely,laser power,scanning speed,hatch spacing, layer thickness and powder temperature, on the tensile strength for selective laser...In the present work,a study is made to investigate the effects of process parameters,namely,laser power,scanning speed,hatch spacing, layer thickness and powder temperature, on the tensile strength for selective laser sintering( SLS) of polystyrene( PS). Artificial neural network( ANN) methodology is employed to develop mathematical relationships between the process parameters and the output variable of the sintering strength. Experimental data are used to train and test the network. The present neural network model is applied to predicting the experimental outcome as a function of input parameters within a specified range. Predicted sintering strength using the trained back propagation( BP) network model showed quite a good agreement with measured ones. The results showed that the networks had high processing speed,the abilities of error-correcting and self-organizing. ANN models had favorable performance and proved to be an applicable tool for predicting sintering strength SLS of PS.展开更多
The slow degration of iron limits its bone implant application.The solid solution of Zn in Fe is expected to accelerate the degradation.In this work,mechanical alloying(MA)was used to prepare Fe-Zn powder with supersa...The slow degration of iron limits its bone implant application.The solid solution of Zn in Fe is expected to accelerate the degradation.In this work,mechanical alloying(MA)was used to prepare Fe-Zn powder with supersaturated solid solution.MA significantly decreased the lamellar spacing between particles,thus reducing the diffusion distance of solution atoms.Moreover,it caused a number of crystalline defects,which further promoted the solution diffusion.Subsequently,the MA-processed powder was consolidated into Fe-Zn part by laser sintering,which involved a partial melting/rapid solidification mechanism and retained the original supersaturated solid solution.Results proved that the Fe-Zn alloy became more susceptible with a lowered corrosion potential,and thereby an accelerated corrosion rate of(0.112±0.013)mm/year.Furthermore,it also exhibited favorable cell behavior.This work highlighted the advantage of MA combined with laser sintering for the preparation of Fe-Zn implant with improved degradation performance.展开更多
With the development of portable electronic devices, electric vehicles, and power storage systems, the demand for rechargeable batteries with high energy density is growing rapidly [1–5]. In the field of lithium-ion ...With the development of portable electronic devices, electric vehicles, and power storage systems, the demand for rechargeable batteries with high energy density is growing rapidly [1–5]. In the field of lithium-ion batteries, the unconventional anode materials such as tin, silicon, metallic lithium, and transition-metal oxides have been extensively studied due to the high capacity, but they are still inapplicable because of the low initial coulombic efficiency(ICE) and/or the poor cycling stability [5–9].展开更多
How to directly fabricate metallic functional parts with selective laser sintering (SLS) process is a potential technique that scientists are researching. Existent problems during directly fabricating metal part by us...How to directly fabricate metallic functional parts with selective laser sintering (SLS) process is a potential technique that scientists are researching. Existent problems during directly fabricating metal part by use of SLS are analyzed. For the sake of solving the problems, a new idea of adding self-propagating high-temperature synthesis (SHS) material into metallic powder material to form new type of SLS metallic powder material is put forward. This powder material can release controllable amount of heat during its interaction with the laser beam energy to reduce the requirement to laser power during directly sintering metallic part, to prolong the time of metallic liquid phase existing, and to improve the intensity and accuracy of SLS part. For this reason, SHS material′s interaction with the CO2 laser beam energy is researched, which proves that CO2 laser beam energy may instantly ignite SHS reaction. On the basis of the above-mentioned researches, the effect of sintering the metal powder material mixing SHS material with CO2 laser is also researched, which shows: there is an optimal blending ratio of various material in the new metallic powder material. Under the optimal blending ratio and SLS process parameters, this new metallic powder material can indeed release amount of heat and SHS reaction may be controlled within the laser sintering. This research result makes it possible that the metallic part is directly sintered with small CO2 laser (less than 50W), which may greatly reduce the volume, cost and running expenditure of SLS machine, be propitious to application.展开更多
In order to enhance the strength of sustainable walnut shell/Co-PES(WSPC)sintered parts,wax-filtrated posttreatment was carried out.The effects of treating fluid temperature,preheating time and immersion time on the b...In order to enhance the strength of sustainable walnut shell/Co-PES(WSPC)sintered parts,wax-filtrated posttreatment was carried out.The effects of treating fluid temperature,preheating time and immersion time on the bending strength of WSPC wax-filtrated parts were analyzed by single factor analysis method.To obtain an accurate model for predicting the bending strength of the WSPC wax-filtrated part,the experiments were involved by using Box-Behnken design(BBD).Main parameters,such as treating fluid temperature,preheating time and immersion time,and their interactive effects were analyzed through analysis of variance(ANOVA)and graphical contours.The results demonstrated that all parameters’direct effects were significant to bending strength of the WSPC wax-filtrated part.Its optimum value was 5.0 MPa when the treating fluid temperature of 70°C,preheating time of 50 min,and immersion time of 20 s.The predicted models effectively validated had good predicting accuracy.The WSPC wax-filtrated part using optimal processing parameters was processed by investment casting,and then the metal casting of dimensional stability and smooth surface was obtained.Investment casting was done using WSPC wax-filtrated parts under optimal process parameters and then metal parts with stable structure size and smooth surface can be obtained,which indicates that WSPC material can be used for investment casting.展开更多
Layer manufacture technologies are gaining increasing attention in the manufacturing for the production of polymer mould tooling. Layer manufacture techniques can be used in this potential manufacturing area to produc...Layer manufacture technologies are gaining increasing attention in the manufacturing for the production of polymer mould tooling. Layer manufacture techniques can be used in this potential manufacturing area to produce tooling either indirectly or directly, and powder metal based layer manufacture systems are considered as an effective way of producing rapid tooling. Mechanical properties and accuracy are critical for tooling. This paper reports the results of an experimental study examining the potential of layer manufacturing processes to deliver production tooling for polymer manufacture. A comparison between indirectly selective laser sintering and directly selective laser sintering to provide the tooling was reported. Three main areas were addressed during the study: mechanical strength, accuracy, and build rate. Overviews of the results from the studies were presented.展开更多
This paper presents initial development of polymer application. PNC materials containing a polyamide (PA) and nano to improve the mechanical properties. Commercial polyamide 6 nanocomposites (PNC) material for rap...This paper presents initial development of polymer application. PNC materials containing a polyamide (PA) and nano to improve the mechanical properties. Commercial polyamide 6 nanocomposites (PNC) material for rapid manufacturing (RM) particles (5 wt%) were produced by solution blending with the aim (PA6) was dissolved in formic acid (HCO2H) together with two different types of nano particle materials: yttrium stabilised zirconia (YSZ) and Hectorite clay (Benton 166) and spray-dried to create powder, creating powder with particle sizes in the range of 10-40 μm. The materials were processed on a CO2 selective laser sintering (SLS) experimental machine. Mechanical properties of the PNCs were evaluated and the results were compared with the unfilled base polymer. Good dispersion of additives was achieved by solution blending, however the PA6 was degraded during the material preparation and spray drying process which resulted in the formation of porous structure and low strength. However the addition of 5 (wt%) nano particles in the PA6 has shown to increase strength by an average of 50-60%. Further work on powder preparation is required in order to fully realize these performance benefits.展开更多
Direct slicing from GAD models to generate sectional contours of the part to be sintered for Selective Laser Sintering (SLS) may overcome inherent disadvantages of using a Stereo Lithography (STL) format. In this ...Direct slicing from GAD models to generate sectional contours of the part to be sintered for Selective Laser Sintering (SLS) may overcome inherent disadvantages of using a Stereo Lithography (STL) format. In this paper, a direct slicing procedure is proposed for Selective Laser Sintering based on material performance and process parameters. Slicing thickness depends on the 3 D geometric model, material performance and process parameters. The relationship among material performance, process parameters and the largest slicing thickness is established using analysis of a sintering temperature field. A dynamic linked library is developed to realize direct slicing from a CAD model.展开更多
A two-dimensional multi-physics finite element model is developed to simulate the Selective Laser Sintering(SLS)process using Inconel 625 powders.The validity of the developed model is first assessed by comparing its ...A two-dimensional multi-physics finite element model is developed to simulate the Selective Laser Sintering(SLS)process using Inconel 625 powders.The validity of the developed model is first assessed by comparing its results with experimental data.Various factors such as phase transition,recoil pressure,surface tension,and theMarangoni force are considered.The study’s findings underscore that the morphology and thermal-fluid dynamics of the molten pool in the SLS process are predominantly shaped by the influence of the Marangoni force and recoil pressure acting on its surface.The recoil pressure at the front of the laser spot rises exponentially with temperature,making the liquid metal move downward,and creating a depression at the pool’s head.It also causes particles to splash from the pool’s rear edge.The study explores the influence of the backward Marangoni force,where hightemperature liquid flows from the front to the rear of the molten pool,creating a vortex and moving the pool in the rear.Process parameters like laser intensity,scan speed,and spot size were analyzed.The findings indicate that higher laser power lower scanning speed and laser beam spot size lead to increased width and depth of the molten pool.展开更多
Poor flowability of printable powders and long preparation cycles are the main challenges in the selective laser sintering(SLS)of chopped carbon fiber(C_(f))reinforced silicon carbide(SiC)composites with complex struc...Poor flowability of printable powders and long preparation cycles are the main challenges in the selective laser sintering(SLS)of chopped carbon fiber(C_(f))reinforced silicon carbide(SiC)composites with complex structures.In this study,we develop an efficient and novel processing route in the fabrication of lightweight SiC composites via the SLS of phenolic resin(PR)and Cr powders with the addition of a-SiC particles combined with the one-step reactive melt infiltration(RMI).The effects of a-SiC addition on the microstructural evolution of the C_(f)/SiC/PR printed bodies,C_(f)/SiC/C green bodies,and derived SiC composites were investigated.The results indicate that the added a-SiC particles play an important role in enhancing the flowability of raw powders,reducing the porosity.increasing the reliability of the C/SiC/C green bodies,and contributing to improving the microstructure homogeneity and mechanical properties of the SiC composites.The maximum density,flexural strength,and fracture toughness(Kic)of the SiC composites are 2.749±0.006 g·cm^(3),266±5 MPa,and 3.30±0.06 MPa-m,respectively.The coefficient of thermal expansion(CTE,a)of the SiC composites is approximately 4.29×10^(-6)K^(-1)from room temperature(RT)to 900℃,and the thermal conductivity(x)is in the range of 80.15-92.48 W·m^(-1)·K^(-1)at RT.The high-temperature strength of the SiC composites increase to 287±18 MPa up to 1200℃.This study provides a novel as well as feasible tactic for the preparation of high-quality printable powders as well as lightweight,high-strength,and high-x SiC composites with complex structures by the SLS and RMI.展开更多
The advent of rapid prototyping & manufacturing techniques represents a major breakthrough in production engineering. This paper is concerned with the software system aspects of the selective laser sintering (SL...The advent of rapid prototyping & manufacturing techniques represents a major breakthrough in production engineering. This paper is concerned with the software system aspects of the selective laser sintering (SLS),i.e.the issues that deal with an external geometric CAD model to automatically control the physical layering fabrication process as directly as possible ,regardless of the source of the model. The general issues are described and some key methods are given in this paper.展开更多
A calculation model of stress field in laser additive manufacturing of walnut shell composite powder(walnut shell/Co-PES powder)was established.The DFLUX subroutine was used to implement the moveable application of a ...A calculation model of stress field in laser additive manufacturing of walnut shell composite powder(walnut shell/Co-PES powder)was established.The DFLUX subroutine was used to implement the moveable application of a double ellipsoid heat source by considering the mechanical properties varying with temperature.The stress field was simulated by the sequential coupling method,and the experimental results were in good accordance with the simulation results.In addition,the distribution and variation of stress and strain field were obtained in the process of laser additive manufacturing of walnut shell composite powder.The displacement of laser additive manufacturing walnut shell composite parts gradually decreased with increasing preheating temperature,decreasing laser power and increasing scanning speed.During the cooling process,the displacement of laser additive manufacturing of walnut shell composite parts gradually increased with the increasing preheating temperature,decreasing scanning speed and increasing laser power.展开更多
In order to improve parts accuracy, a method of adding heat balance support (HBS) was proposed, and the detailed algorithm for generating HBS was developed. A number of experiments and a comparison between similar s...In order to improve parts accuracy, a method of adding heat balance support (HBS) was proposed, and the detailed algorithm for generating HBS was developed. A number of experiments and a comparison between similar softwares, showed that the algorithm is efficient and feasible. Moreover, different features of riBS were studied for different kinds of materials, such as PS and nylon. The research findings indicate that automatically adding HBS can significantly improve the accuracy of the parts, and that the algorithm for generating HBS is efficient and precise.展开更多
基金This work was financially supported by the Joint Funds of the National Natural Science Foundation of China(Grant No.U1808216)the Shanxi Provincial Key Research and Development Project(2022ZDYF072).
文摘A cold method was used to prepare coated sand for application in the selective laser sintering(SLS)process.Tensile strength,loss on ignition,gas evolution,and accuracy of the SLS samples were tested and analyzed,and the baking process was thoroughly investigated.Compared with coated sand prepared by the hot method,the cold method yields a more uniform and complete resin film on the sand's surface,resulting in enhanced tensile strength and accuracy.Additionally,the cold method requires a lower binder content to meet the same strength requirements,thereby minimizing gas evolution,reducing porosity defects,and ultimately improving casting quality.The coated sand samples prepared through the cold method exhibit superior accuracy,with a size error of within±0.4 mm.In contrast,the coated sand samples prepared by the hot method display a lower accuracy,with an average negative error of 2.1993 mm.The highest tensile strength could be attained by controlling the baking temperature within a suitable range(180-190°C),which can effectively reduce the generation of gas,thus contributing to improved overall performance.
文摘A mathematical model is developed for simulating the heat transferring behavior in a direct metal laser sintering process. The model considers the thermal phenomena involved in the process, including conduction, radiation, and convection. A formula for the calculation of the heat conductivity of a sintering system containing solid phase, liquid phase, and gas phase is given. Due to the continuous movement of the laser beam, a local coordinate system centered on the laser beam is used to simplify the analytical calculation. Assuming that it is approximately a Gaussian laser beam, the heat conduction equation is resolved based on the assumption of the thermal insulating boundary conditions and the fixed thermal physical parameters. The FORTRAN language is employed to compile the program to simulate the temperature field in the direct copper powder sintering process. It shows a good agreement with the preliminary experimental results.[KH3/4D]
基金financially supported by the National Defence Key Discipline Laboratory of Light Alloy Processing Science and Technology,Aeronautical Science Foundation of China(Grant No.2011ZE56007)the Natural Science Foundation of Jiangxi Province(Grant No.2010GZC0159)the High Technology Landing Program of Jiangxi University(Grant No.DB201303014)
文摘Baozhu sand particles with size between 75 μm and 150 μm were coated by resin with the ratio of 1.5 wt.% of sands. Laser sintering experiments were carried out to investigate the effects of laser energy density(E = P/v), with different laser power(P) and scanning velocity(v), on the dimensional accuracy and tensile strength of sintered parts. The experimental results indicate that with the constant scanning velocity, the tensile strength of sintered samples increases with an increase in laser energy density; while the dimensional accuracy apparently decreases when the laser energy density is larger than 0.032 J·mm-2. When the laser energy density is 0.024 J·mm-2, the tensile strength shows no obvious change; but when the laser energy density is larger than 0.024 J·mm-2, the sample strength is featured by the initial increase and subsequent decrease with simultaneous increase of both laser power and scanning velocity. In this study, the optimal energy density range for laser sintering is 0.024-0.032 J·mm-2. Moreover, samples with the best tensile strength and dimensional accuracy can be obtained when P = 30-40 W and v = 1.5-2.0 m·s-1. Using the optimized laser energy density, laser power and scanning speed, a complex coated sand mould with clear contour and excellent forming accuracy has been successfully fabricated.
文摘Selective laser sintering (SLS) is a new process to prepare the polystyrene (PS)/Al2O3 nanocomposites. In this paper, with different laser power and other processing parameters unchanged, the morphology, density and mechanical properties of the sintered specimens were investigated. It was found that nano-sized inorganic particles are uniformly located in the PS matrix and the maximum density of the sintered specimens with pure PS powder reaches 1.07 g/cm^3, higher than 1.04 g/cm^3 that of the sintered specimens with mixture powder. Due to strengthening and toughness of the nano-sized Al2O3 inorganic particles, the maximum notched impact strength and tensile strength of the sintered part mixed with nano-sized inorganic particles are improved greatly from 7.5 to 12.1 kJ/m^2 and from 6.5 to 31.2 MPa, respectively, under the same sintering condition.
文摘Using a special coated sand as the material of the selected laser sintering (SLS), the authors test and investigate the strength change of the test samples in terms of different sintering parameters (scanning speed, laser power, sintering thickness, and so on). The characteristics of coated sand hardening by laser beam are analyzed. The sintered mold (or core) for given casting is poured with molten metal.
基金supported by the National Key R&D Program of China(2020YFB2008300,2020YFB2008304)the National Natural Science Foundation of China(51775204,51375190,59635040)。
文摘Selective laser sintering(SLS),as a kind of additive manufacturing technology,which uses a laser beam to scan and heat powder material layer by layer to form parts(models),is widely used in the field of casting,mainly for preparing casting coated sand cores,investment casting patterns,etc.The SLS technique facilitates rapid casting and shortens the casting production periods by eliminating mold preparation.In this study,we reached conclusions for the basic principles and characteristics of SLS methods,and focused on the research status,key technology and development trend of SLS in the fields of forming coated sand-casting molds and investment casting patterns.
基金the support from the Shanghai Science and Technology Committee Innovation Grant(Grant No.19ZR1404600)Fudan University-CIOMP Joint Fund(FC2020-006)。
文摘Polymers are widely used materials in aerospace,automotive,construction,medical devices and pharmaceuticals.Polymers are being promoted rapidly due to their ease of manufacturing and improved material properties.Research on polymer processing technology should be paid more attention to due to the increasing demand for polymer applications.Selective laser sintering(SLS)uses a laser to sinter powdered materials(typical polyamide),and it is one of the critical additive manufacturing(AM)techniques of polymer.It irradiates the laser beam on the defined areas by a computer-aided design three-dimensional(3D)model to bind the material together to create a designed 3D solid structure.SLS has many advantages,such as no support structures and excellent mechanical properties resembling injection moulded parts compared with other AM methods.However,the ability of SLS to process polymers is still affected by some defects,such as the porous structure and limited available types of SLS polymers.Therefore,this article reviews the current state-of-the-art SLS of polymers,including the fundamental principles in this technique,the SLS developments of typical polymers,and the essential process parameters in SLS.Furthermore,the applications of SLS are focused,and the conclusions and perspectives are discussed.
基金National Natural Science Foundation of China(No.51475315)Innovative Project on the Integration of Industry,Education and Research of Jiangsu Province,China(No.BY2014059-10)
文摘In the present work,a study is made to investigate the effects of process parameters,namely,laser power,scanning speed,hatch spacing, layer thickness and powder temperature, on the tensile strength for selective laser sintering( SLS) of polystyrene( PS). Artificial neural network( ANN) methodology is employed to develop mathematical relationships between the process parameters and the output variable of the sintering strength. Experimental data are used to train and test the network. The present neural network model is applied to predicting the experimental outcome as a function of input parameters within a specified range. Predicted sintering strength using the trained back propagation( BP) network model showed quite a good agreement with measured ones. The results showed that the networks had high processing speed,the abilities of error-correcting and self-organizing. ANN models had favorable performance and proved to be an applicable tool for predicting sintering strength SLS of PS.
基金Projects(51935014,82072084,81871498)supported by the Natural Science Foundation of ChinaProjects(20192ACB20005,2020ACB214004)supported by the Jiangxi Provincial Natural Science Foundation of China+4 种基金Project(20201BBE51012)supported by the Provincial Key R&D Projects of Jiangxi Province,ChinaProject(2018)supported by the Guangdong Province Higher Vocational Colleges&Schools Pearl River Scholar Funded Scheme,ChinaProject(2017RS3008)supported by Hunan Provincial Science and Technology Plan,ChinaProject supported by the Open Research Fund of Jiangsu Key Laboratory of Precision and Micro-Manufacturing Technology,ChinaProject(2020M682114)China Postdoctoral Science Foundation。
文摘The slow degration of iron limits its bone implant application.The solid solution of Zn in Fe is expected to accelerate the degradation.In this work,mechanical alloying(MA)was used to prepare Fe-Zn powder with supersaturated solid solution.MA significantly decreased the lamellar spacing between particles,thus reducing the diffusion distance of solution atoms.Moreover,it caused a number of crystalline defects,which further promoted the solution diffusion.Subsequently,the MA-processed powder was consolidated into Fe-Zn part by laser sintering,which involved a partial melting/rapid solidification mechanism and retained the original supersaturated solid solution.Results proved that the Fe-Zn alloy became more susceptible with a lowered corrosion potential,and thereby an accelerated corrosion rate of(0.112±0.013)mm/year.Furthermore,it also exhibited favorable cell behavior.This work highlighted the advantage of MA combined with laser sintering for the preparation of Fe-Zn implant with improved degradation performance.
基金supported by the Key Research and Development of Ministry of Science and Technology of China(No.2018YFE0202601)the Zhejiang Provincial Natural Science Foundation of China(Grant No.LTY20E010001)。
文摘With the development of portable electronic devices, electric vehicles, and power storage systems, the demand for rechargeable batteries with high energy density is growing rapidly [1–5]. In the field of lithium-ion batteries, the unconventional anode materials such as tin, silicon, metallic lithium, and transition-metal oxides have been extensively studied due to the high capacity, but they are still inapplicable because of the low initial coulombic efficiency(ICE) and/or the poor cycling stability [5–9].
文摘How to directly fabricate metallic functional parts with selective laser sintering (SLS) process is a potential technique that scientists are researching. Existent problems during directly fabricating metal part by use of SLS are analyzed. For the sake of solving the problems, a new idea of adding self-propagating high-temperature synthesis (SHS) material into metallic powder material to form new type of SLS metallic powder material is put forward. This powder material can release controllable amount of heat during its interaction with the laser beam energy to reduce the requirement to laser power during directly sintering metallic part, to prolong the time of metallic liquid phase existing, and to improve the intensity and accuracy of SLS part. For this reason, SHS material′s interaction with the CO2 laser beam energy is researched, which proves that CO2 laser beam energy may instantly ignite SHS reaction. On the basis of the above-mentioned researches, the effect of sintering the metal powder material mixing SHS material with CO2 laser is also researched, which shows: there is an optimal blending ratio of various material in the new metallic powder material. Under the optimal blending ratio and SLS process parameters, this new metallic powder material can indeed release amount of heat and SHS reaction may be controlled within the laser sintering. This research result makes it possible that the metallic part is directly sintered with small CO2 laser (less than 50W), which may greatly reduce the volume, cost and running expenditure of SLS machine, be propitious to application.
基金This study was supported by Scientific Research Staring Foundation of Northeast Petroleum University(1305021868)the National Natural Science Foundation of China(51475089)+3 种基金the National Key R&D Program of China(2017YFD0601004)the Natural Science Foundation of Heilongjiang Province(ZD2017009)Fundamental Research Funds for the Central Universities(2572017PZ06)the Special Project of Scientific and Technological Development of Central Guidance for Local(ZY16C03).
文摘In order to enhance the strength of sustainable walnut shell/Co-PES(WSPC)sintered parts,wax-filtrated posttreatment was carried out.The effects of treating fluid temperature,preheating time and immersion time on the bending strength of WSPC wax-filtrated parts were analyzed by single factor analysis method.To obtain an accurate model for predicting the bending strength of the WSPC wax-filtrated part,the experiments were involved by using Box-Behnken design(BBD).Main parameters,such as treating fluid temperature,preheating time and immersion time,and their interactive effects were analyzed through analysis of variance(ANOVA)and graphical contours.The results demonstrated that all parameters’direct effects were significant to bending strength of the WSPC wax-filtrated part.Its optimum value was 5.0 MPa when the treating fluid temperature of 70°C,preheating time of 50 min,and immersion time of 20 s.The predicted models effectively validated had good predicting accuracy.The WSPC wax-filtrated part using optimal processing parameters was processed by investment casting,and then the metal casting of dimensional stability and smooth surface was obtained.Investment casting was done using WSPC wax-filtrated parts under optimal process parameters and then metal parts with stable structure size and smooth surface can be obtained,which indicates that WSPC material can be used for investment casting.
文摘Layer manufacture technologies are gaining increasing attention in the manufacturing for the production of polymer mould tooling. Layer manufacture techniques can be used in this potential manufacturing area to produce tooling either indirectly or directly, and powder metal based layer manufacture systems are considered as an effective way of producing rapid tooling. Mechanical properties and accuracy are critical for tooling. This paper reports the results of an experimental study examining the potential of layer manufacturing processes to deliver production tooling for polymer manufacture. A comparison between indirectly selective laser sintering and directly selective laser sintering to provide the tooling was reported. Three main areas were addressed during the study: mechanical strength, accuracy, and build rate. Overviews of the results from the studies were presented.
文摘This paper presents initial development of polymer application. PNC materials containing a polyamide (PA) and nano to improve the mechanical properties. Commercial polyamide 6 nanocomposites (PNC) material for rapid manufacturing (RM) particles (5 wt%) were produced by solution blending with the aim (PA6) was dissolved in formic acid (HCO2H) together with two different types of nano particle materials: yttrium stabilised zirconia (YSZ) and Hectorite clay (Benton 166) and spray-dried to create powder, creating powder with particle sizes in the range of 10-40 μm. The materials were processed on a CO2 selective laser sintering (SLS) experimental machine. Mechanical properties of the PNCs were evaluated and the results were compared with the unfilled base polymer. Good dispersion of additives was achieved by solution blending, however the PA6 was degraded during the material preparation and spray drying process which resulted in the formation of porous structure and low strength. However the addition of 5 (wt%) nano particles in the PA6 has shown to increase strength by an average of 50-60%. Further work on powder preparation is required in order to fully realize these performance benefits.
文摘Direct slicing from GAD models to generate sectional contours of the part to be sintered for Selective Laser Sintering (SLS) may overcome inherent disadvantages of using a Stereo Lithography (STL) format. In this paper, a direct slicing procedure is proposed for Selective Laser Sintering based on material performance and process parameters. Slicing thickness depends on the 3 D geometric model, material performance and process parameters. The relationship among material performance, process parameters and the largest slicing thickness is established using analysis of a sintering temperature field. A dynamic linked library is developed to realize direct slicing from a CAD model.
文摘A two-dimensional multi-physics finite element model is developed to simulate the Selective Laser Sintering(SLS)process using Inconel 625 powders.The validity of the developed model is first assessed by comparing its results with experimental data.Various factors such as phase transition,recoil pressure,surface tension,and theMarangoni force are considered.The study’s findings underscore that the morphology and thermal-fluid dynamics of the molten pool in the SLS process are predominantly shaped by the influence of the Marangoni force and recoil pressure acting on its surface.The recoil pressure at the front of the laser spot rises exponentially with temperature,making the liquid metal move downward,and creating a depression at the pool’s head.It also causes particles to splash from the pool’s rear edge.The study explores the influence of the backward Marangoni force,where hightemperature liquid flows from the front to the rear of the molten pool,creating a vortex and moving the pool in the rear.Process parameters like laser intensity,scan speed,and spot size were analyzed.The findings indicate that higher laser power lower scanning speed and laser beam spot size lead to increased width and depth of the molten pool.
基金supported by the National Natural Science Foundation of China(Nos.52073299,52172077,U22A20129,and 51902329)the National Key R&D Program of China(No.2022YFB3706303)the Youth Innovation Promotion Association CAS(No.2018289).
文摘Poor flowability of printable powders and long preparation cycles are the main challenges in the selective laser sintering(SLS)of chopped carbon fiber(C_(f))reinforced silicon carbide(SiC)composites with complex structures.In this study,we develop an efficient and novel processing route in the fabrication of lightweight SiC composites via the SLS of phenolic resin(PR)and Cr powders with the addition of a-SiC particles combined with the one-step reactive melt infiltration(RMI).The effects of a-SiC addition on the microstructural evolution of the C_(f)/SiC/PR printed bodies,C_(f)/SiC/C green bodies,and derived SiC composites were investigated.The results indicate that the added a-SiC particles play an important role in enhancing the flowability of raw powders,reducing the porosity.increasing the reliability of the C/SiC/C green bodies,and contributing to improving the microstructure homogeneity and mechanical properties of the SiC composites.The maximum density,flexural strength,and fracture toughness(Kic)of the SiC composites are 2.749±0.006 g·cm^(3),266±5 MPa,and 3.30±0.06 MPa-m,respectively.The coefficient of thermal expansion(CTE,a)of the SiC composites is approximately 4.29×10^(-6)K^(-1)from room temperature(RT)to 900℃,and the thermal conductivity(x)is in the range of 80.15-92.48 W·m^(-1)·K^(-1)at RT.The high-temperature strength of the SiC composites increase to 287±18 MPa up to 1200℃.This study provides a novel as well as feasible tactic for the preparation of high-quality printable powders as well as lightweight,high-strength,and high-x SiC composites with complex structures by the SLS and RMI.
文摘The advent of rapid prototyping & manufacturing techniques represents a major breakthrough in production engineering. This paper is concerned with the software system aspects of the selective laser sintering (SLS),i.e.the issues that deal with an external geometric CAD model to automatically control the physical layering fabrication process as directly as possible ,regardless of the source of the model. The general issues are described and some key methods are given in this paper.
基金Supported by the Scientific Research Start-Up Fund Project of Northeast Petroleum University(2019KQ67 and 2021KQ09)the Guiding Innovation Fund Project of Northeast Petroleum University(2021YDL-13)+1 种基金National Natural Science Foundation of China(52075090)Supported by the National Key R&D Program of China(2017YFD0601004).
文摘A calculation model of stress field in laser additive manufacturing of walnut shell composite powder(walnut shell/Co-PES powder)was established.The DFLUX subroutine was used to implement the moveable application of a double ellipsoid heat source by considering the mechanical properties varying with temperature.The stress field was simulated by the sequential coupling method,and the experimental results were in good accordance with the simulation results.In addition,the distribution and variation of stress and strain field were obtained in the process of laser additive manufacturing of walnut shell composite powder.The displacement of laser additive manufacturing walnut shell composite parts gradually decreased with increasing preheating temperature,decreasing laser power and increasing scanning speed.During the cooling process,the displacement of laser additive manufacturing of walnut shell composite parts gradually increased with the increasing preheating temperature,decreasing scanning speed and increasing laser power.
基金supported by the Innovatory Group Program of the Natural Science Foundation of Hubei Province (No. 2004ABC001)the Open Foundation of State Key Laboratory of Powder Metallurgy of Center South University (No. 200506123102A), China
文摘In order to improve parts accuracy, a method of adding heat balance support (HBS) was proposed, and the detailed algorithm for generating HBS was developed. A number of experiments and a comparison between similar softwares, showed that the algorithm is efficient and feasible. Moreover, different features of riBS were studied for different kinds of materials, such as PS and nylon. The research findings indicate that automatically adding HBS can significantly improve the accuracy of the parts, and that the algorithm for generating HBS is efficient and precise.