Microstructure and Properties of AlCoCrFeNiTi High-Entropy Alloy Coatings Prepared by Laser Cladding

21-4N(5Cr21Mn9Ni4N)is extensively employed in the production of engine valves,operating under severe conditions.Apart from withstanding high-temperature gas corrosion,it must also endure the impact of cylinder explosion pressure.The predominant failure mode of 21-4N valves is abrasive wear.Surface coatings serve as an effective approach to prevent such failures.In this investigation,Laser cladding technology was utilized to fabricate AlCoCrFeNiTi high entropy alloy coatings onto the surfaces of 21-4N valves.According to the findings,the cladding zone has a normal dendritic microstructure,a good substrate-to-cladding layer interaction,and no obvious flaws.In terms of hardness,the cladding demonstrates an average hardness of 620 HV.The hardness has increased by 140%compared to the substrate.The average hardness of the cladding remains at approximately 520 HV even at elevated temperatures.Regarding frictional wear performance,between 400℃and 800℃,the cladding layer exhibits an average friction coefficient of 0.4,with the primary wear mechanisms being abrasive wear,adhesive wear,and a minor degree of plastic deformation.

Surface hardening of Fe-based alloy powders by Nd:YAG laser cladding followed by electrospark deposition with WC-Co cemented carbide

This paper presents the results of a study concerned with the surface hardening of Fe-based alloys and WC-8Co cemented carbide by inte- grating laser cladding and the electrospark deposition processes. Specimens of low carbon steel were processed firstly by laser cladding with Fe-based alloy powders and then by electrospark deposition with WC-SCo cemented carbide. It is shown that, for these two treatments, the electrospark coating possesses finer microstructure than the laser coating, and the thickness and surface hardness of the electrospark coating can be substantially increased.

CALCULATION OF 3-D TRANSIENT TEMPERATURE FIELD DURING LASER TRANSFORMATION HARDENING PROCESS

A three-dimensional transient heat transfer model for laser transformation hardening process has been developed in this paper. The finite size of the laser treated sample, the surface heat loss of the sample, the latent heat of phase transformation and the temperature dependence of thermal properties of materials were considered. The heat source was considered as a moving Gaussian heat flux with a constant velocity. Three-dimension unequally spatial grid explicit finite difference equations, alternating direction implicit finite difference equations and implicit finite difference equations were deduced respectively. Three programs to calculate the temperature field were developed using Fortran language. The transient temperature fields of C22, 42CrMo, C60 steel samples during laser transformation hardening process were calculated using these programs, and the widths and depths of laser transformation hardening zones were also predicted. C22, 42CrMo, C60 steel samples were treated by CO_2 laser,the widths and depths of laser transformation hardening zones of these samples were also measured experimentally. The calculated widths and depths of laser transformation hardening zones are in good agreement with the experimental results.

Study on Laser Transformation Hardening of HT250 by High Speed Axis Flow CO_2 Laser

In this article, laser transformation hardening of HT250 material by high speed axis flow CO2 laser was investigated for first time in China. Appropriate laser hardening parameters, such as laser energy power P(W), laser scanning rate V(m/min), were optimized through a number of experiments. The effect of the mentioned parameters on the hardened zone, including its case depth, microhardness distributions etc., were analyzed. Through the factual experiments, it is proved that axial flow CO2laser, which commonly outputs low mode laser beam, can also treat materials as long as the treating parameters used are rational. During the experiments, the surface qualities of some specimens treated by some parameters were found to be enhanced, which does not coincide with the former results. Furthermore in the article, the abnormal phenomenon observed in the experiments is discussed. According to the experimental results, the relationship between laser power density q and scanning rate V is shown in a curve and the corresponding formulation, which have been proved to be valuable for choosing the parameters of laser transformation hardening by axial flow CO2 lasers, was also given.

Microstructure and high temperature tribological behavior of laser cladding Ni60A alloys coatings on 45 steel substrate

The crack-free Ni60 A coating was fabricated on 45 steel substrate by laser cladding and the microstructure including solidification characteristics, phases constitution and phase distribution was systematically investigated. The high temperature friction and wear behavior of the cladding coating and substrate sliding against GCr15 ball under different loads was systematically evaluated. It was found that the coating has homogenous and fine microstructure consisting of γ（Ni） solid solution, a considerable amount of network Ni-Ni3 B eutectics, m^23C6 with the floret-shape structure and Cr B with the dark spot-shape structure uniformly distributing in interdendritic eutectics. The microhardness of the coating is about 2.6 times as much as that of the substrate. The coating produces higher friction values than the substrate under the same load condition, but the friction process on the coating keeps relatively stable. Wear rates of the coating are about 1/6.2 of that of the substrate under the higher load（300 g）. Wear mechanism of the substrate includes adhesion wear, abrasive wear, severe plastic deformation and oxidation wear, while that of the coating is merely a combination of mild abrasive wear and moderate oxidation wear.

Synthesis of Y_2O_3 particle enhanced Ni/TiC composite on TC4 Ti alloy by laser cladding

A Y2O3 particle enhanced Ni/TiC composite coating was fabricated in-situ on a TC4 Ti alloy by laser surface cladding. The phase component, microstructure, composition distribution and properties of the composite layer were investigated. The composite layer has graded microstructures and compositions, due to the fast melting followed by rapid solidification and cooling during laser cladding. The TiC powders are completely dissolved into the melted layer during melting and segregated as fine dendrites when solidified. The size of TiC dendrites decreases with increasing depth. Y2O3 fine particles distribute in the whole clad layer. The Y2O3 particle enhanced Ni/TiC composite layer has a quite uniform hardness along depth with a maximum value of HV1380, which is 4 times higher than the initial hardness. The wear resistance of the Ti alloy is significantly improved after laser cladding due to the high hardness of the composite coating.

Controlled Laser Transformation Hardening of Martensitic Stainless Steel by Pulsed Nd:YAG Laser

Laser transformation hardening （LTH） was applied to the surface of the AISI 420 martensitic stainless steel by a pulsed Nd：YAG laser to obtain optimum hardness. The influences of process parameters （laser pulse energy, duration time, and travel speed） on the depth and hardness of laser treated area were investigated. Image analysis of SEM microstructure of AISI 420 showed that plate-like carbide have almost fully and （30-40）% of globular carbide particles dissolved into the matrix after laser transformation hardening by pulsed laser and the microstructure was refined to obtain controlled tempered martensite microstructure with 450 VHN hardness.

Interface characteristics of Al_2O_3－13%TiO_2 ceramic coatings prepared by laser cladding

Al2O3-13%TiO2 （mass fraction） coatings, prepared by laser cladding on nickel-based alloy, were heated using high frequency induction sources. The coating microstructure and the interface between bond coating and ceramic coating were characterized by SEM, XRD and EDS. The results show that two-layer substructure exists in the ceramic coating： one layer evolving from fully melted region where the sintered grains grow fully; another layer resembling the liquid-phase-sintered structure consisting of three-dimensional net where the melted Al2O3 particles are embedded in the TiO2-rich matrix. The mechanism of the two-layer substructure formation is also explained in terms of the melting and flattening behavior of the powders during laser cladding processing. The spinel compounds NiAl2O4 and acicular compounds Cr2O3 are discovered in the interface between bond coating and ceramic coating. It proves that the chemical reactions in the laser cladding process will significantly enhance the coating adhesion.

Calculation of Temperature Field During Laser Transformation Hardening of Cylindrical Bodies

A Two-dimensional transient heat transfer model for laser transformation hardening process of cylindrical bodies has been developed. The surface heat loss of the sample, the latent heat of phase transformation, and the temperature dependence of thermal properties of material were considered. The laser heat source was considered as a moving Gaussian heat flux with a constant velocity. Finite element method was used to calculate the transient temperature field. A program to calculate the temperature field was developed using FORTRAN language. The transient temperature field, the width and depth of laser transformation hardening zone of 42CrMo steel sample during laser transformation hardening process was calculated. The widths and depths of laser transformation hardening zones of 42CrMo steel samples were also measured experimentally. The calculated widths and depths of laser transformation hardening zones are in good agreement with the experimental results.

Calculation of Transient Stress Field During Laser Transformation Hardening Process

A thermal elastic-plastic Two-D finite element model to calculate the transient stress field during laser transformation hardening process was developed in this paper. The mechanical properties of material, Young’s module E, Poisson’s ratio v, yield limit s2 and thermal expansion coefficient a are all considered to change with temperature. The equivalent expansion method was used to deal with the problem with phase transformation. A program to calculate the transient stress field was developed using FORTRAN language. The transient and residual stress fields during CO2 laser transformation hardening process of MoCu nodular iron were calculated. The residual stress fields were measured using X-ray diffraction method. The calculated residual stress field of laser transformation hardened MoCu nodular iron is in good agreement with the experimental result.

Laser transformation hardening on rod-shaped carbon steel by Gaussian beam

Laser transformation hardening(LTH) is one of the laser surface modification processes.The surface hardening of rod-shaped carbon steel(SM45C) was performed by lathe-based laser composite processor with Gaussian-beam optical head.The LTH characteristics by dominant processes,longitudinal and depth directional hardness distributions and behaviors of phase transformation in hardened zones were examined.Especially,two concepts of circumferential speed and theoretical overlap rate were applied.When laser power increased or circumferential speed decreased,the surface hardening depth gradually increases due to the increased heat input.Moreover,the longitudinal hardness distribution particularly shows periodicity of repetitive increase and decrease,which results from tempering effect by overlap.Finally,the feasibility of laser transformation hardening is verified by using the beam with Gaussian intensity distribution.

Surface modification of TC4 Ti alloy by laser cladding with TiC+Ti powders

Laser surface cladding was applied on a TC4 Ti alloy to improve its surface properties. Mixed TiC and Ti powders with a TiC-to-Ti mass ratio of 1：3 were put onto the TC4 Ti alloy and subsequently treated by laser beam. The microstructure and composition modifications in the surfaee layer were carefully investigated by using SEM, EDX and XRD. Due to melting, liquid state mixing followed by rapid solidification and cooling, a layer with graded microstructures and compositions formed. The TiC powders were completely dissolved into the melted layer during melting and segregated as fine dendrites when solidified. The inter-dendritic areas were filled with fine a＇ phase lamellae enrich in A1. Mainly due to the reduced TiC volume fraction with increasing depth, the hardness decreases with increasing depth in the laser clad layer with a maximum value of HV1400, about 4.5 times of the initial one.

Microstructure of Cu-based Amorphous Composite Coatings on AZ91D Magnesium Alloy by Laser Cladding

To improve the sliding wear resistance of AZ91D magnesium alloy, Cu-based amorphous composite coatings made of CuaTTi34Zr11Nis and Cu47Ti34Zr11Ni8＋20 wt pct SiC powders were fabricated on AZ91D magnesium alloy by laser cladding, respectively. SEM （scanning electron microscopy）, EDS （energy dispersive X-ray spectroscopy）, XRD （X-ray diffraction） and TEM （transmission electron microscopy） techniques were employed to study the phases of the coatings. The results show that the coatings mainly consist of amorphous phase and different intermetallic compounds. The reason of formation of amorphous phase and the function of SiC particles were explained in details.

Superior corrosion resistance-dependent laser energy density in(CoCrFeNi)95Nb5 high entropy alloy coating fabricated by laser cladding

(CoCrFeNi)95Nb5 high entropy alloy(HEA)coatings were successfully fabricated on a substrate of Q235 steel by laser cladding technology.These(CoCrFeNi)95Nb5 HEA coatings possess excellent properties,particularly corrosion resistance,which is clearly superior to that of some typical bulk HEA and common engineering alloys.In order to obtain appropriate laser cladding preparation process parameters,the effects of laser energy density on the microstructure,microhardness,and corrosion resistance of(CoCrFeNi)95Nb5 HEA coating were closely studied.Results showed that as the laser energy density increases,precipitation of the Laves phase in(CoCrFeNi)95Nb5 HEA coating gradually decreases,and diffusion of the Fe element in the substrate intensifies,affecting the integrity of the(CoCrFeNi)95Nb5 HEA.This decreases the microhardness of(CoCrFeNi)95Nb5 HEA coatings.Moreover,the relative content of Cr2O3,Cr(OH)3,and Nb2O5 in the surface passive film of the coating decreases with increasing energy density,causing corrosion resistance to decrease.This study demonstrates the controllability of a high-performance HEA coating using laser cladding technology,which has significance for the laser cladding preparation of other CoCrFeNi-system HEA coatings.

Laser cladding of Ni-based alloy on copper substrate

The laser cladding of Ni1015 alloy on Cu substrate was prepared by a high power continuous wave CO2 laser. Its microstructure was analyzed by optical microscope （OM）, scanning electron microscope （SEM）, and X-Ray diffraction （XRD）. The average microhardness of the cladding coating was Hv 280, which was almost three times of that of the Cu substrate （Hv 85）. OM and SEM observations showed that the obtained coating had a smooth and uniform surface, as well as a metallurgical combination with the Cu substrate without cracks and pores at the interface. With the addition of copper into the nickel-based alloy, the differences of thermal expansion coefficient and melting point between the interlayer and cladding were reduced, which resulted in low stresses during rapid cooling. Moreover, large amount of （Cu, Ni） solid solution formed a metallurgical bonding between the cladding coating and the substrate, which also relaxed the stresses, leading to the reduction of interfacial cracks and pores after laser cladding.

Research progress of laser cladding self-fluxing alloy coatings on titanium alloys

Laser cladding is a new surface modification technology, and is widely used for fabricating wear and corrosion resistant composites coatings. Self-fluxing alloys have many advantages, such as excellent properties of deoxidizing and slagging, high wear resistance, low melting point and easy cladding, and are often used in laser cladding to improve wear and corrosion resistance of titanium and its alloys. In this paper, the recent development of Ni-based and Co-based self-fluxing alloy coatings which includes the influenee of rare earth and ceramic particles in coatings are summarized. Besides, the effects of processing parameters, such as laser power and scanning speed, on coatings are reviewed. Finally, the trend of development in the future is forecasted.

Influence of cross correlation step length on the surface stress of thin laser cladding Fe314 alloy coatings

To measure the surface stress of thin laser cladding coatings with Rayleigh waves based on the cross correlation function, this pa- per introduced the influence of cross correlation step length on the stress measurement. Flat-shaped specimens made of laser cladding Fe314 alloy coatings were performed by static tensile tests, and Rayleigh wave signals were collected during the test process with an ultrasonic pulser and receiver instrument combined with two Rayleigh wave transducers. The difference in time of flight between two signals was de- termined based on the cross correlation function. The microstructure was observed by scanning electronic microscopy. The influence of the stress on the propagation velocity of Rayleigh waves and the relationship between the difference in time of flight and tensile stress under dif- ferent cross correlation step lengths were analyzed. The inhomogeneous deformation of the coatings affects the relationship between the dif- ference in time of flight and tensile stress; the stress measurement of the coatings is nearly constant with the increase of cross correlation step length when it attains one cycle.

Microstructure and Wear Resistance of in situ NbC Particles Reinforced Ni-based Alloy Composite Coating by Laser Cladding

The in situ synthesized NbC particles reinforced Ni-based alloy composite coating was produced by laser cladding a precursor mixture of Ni-based alloy powder, graphite and niobium powders on a steel substrate. The microstructure, phase composition and wear property of the composite coating were investigated by means of scanning electron microscopy （SEM）, X-ray diffraction （XRD） and dry sliding wear test. The experiment results show that the composite coating is homogeneous and free from cracks, and about 0.8 mm thick. The microstructure of the composite coating is mainly composed of NbC particles, CrB type chromium borides, 7-Ni primary dendrites, and interdendritic eutectics. CrB phases often nucleate and grow on the surface of NbC particles or in their close vicinity. NbC particles are formed via in situ reaction between niobium and graphite in the molten pool during the laser cladding process and they are commonly precipitated in three kinds of morphologies, such as quadrangle, cluster, and flower-like shape. Compared with the pure Ni- based alloy coating, the microhardness of the composite coating is increased about 38%, giving a high average hardness of HV0.21000, and the wear rate of the composite coating is decreased by about 32%, respectively. These are attributed to the presence of in situ synthesized NbC particles and their well distribution in the coating.

THE MULTI-LAYER LASER CLADDING OF Ni60 ALLOY

The Multi layer coating of Ni60 alloy was got by multi layer laser cladding. The height of the coating was about 12mm and the wall of the coating was perpendicular to the base. The microstructure of the coating was made up of fine dendrite. The conjunction between layers was good.

Laser cladding of Al+Ir powders on ZM5 magnesium base alloy

Laser cladding of preplaced Al ＋ Ir powders on a ZM5 magnesium alloy was performed to enhance the corrosion resistance of the ZM5 magnesium alloy. A metallurgical bond was obtained at the coating/substrate interface. The corrosion potential （Ecorr） of the laser cladded sample was 169 mV positive to that of the untreated ZM5 substrate,while the corrosion current （Icorr） was some one order of magnitude lower. The laser cladded sample,unlike the untreated ZM5 substrate,showed a passive region in the polarization plot. Immersion tests confirmed that the corrosion resistance of the laser cladded ZM5 sample was significantly enhanced in 3.5 wt.% NaCl solution. The Al-rich phases of AlIr,Mg17Al12,and Al formed in the cladding layer and the rapid solid characteristics were contributed to the improved corrosion behavior of the coating.