Microstructure of Cu-based Amorphous Composite Coatings on AZ91D Magnesium Alloy by Laser Cladding

To improve the sliding wear resistance of AZ91D magnesium alloy, Cu-based amorphous composite coatings made of CuaTTi34Zr11Nis and Cu47Ti34Zr11Ni8＋20 wt pct SiC powders were fabricated on AZ91D magnesium alloy by laser cladding, respectively. SEM （scanning electron microscopy）, EDS （energy dispersive X-ray spectroscopy）, XRD （X-ray diffraction） and TEM （transmission electron microscopy） techniques were employed to study the phases of the coatings. The results show that the coatings mainly consist of amorphous phase and different intermetallic compounds. The reason of formation of amorphous phase and the function of SiC particles were explained in details.

Microstructure and Wear Behaviour of Laser-Induced Thermite Reaction Al_2O_3 Ceramic Coatings on Pure Aluminum and AA7075 Aluminum Alloy

Wear-resistant laser-induced thermite reaction Al2O3 ceramic coatings can be fabricated on pure Al and AA7075 aluminum alloy by laser cladding （one-step method） and laser cladding followed by laser re-melting （two-step method） using mixed powders CuO-Al-SiO2 in order to improve the wear properties of aluminum and aluminum alloy, respectively. The microstructure of the coatings was characterized by scanning electron microscopy （SEM） and X-ray diffraction （XRD）. The wear resistance of the coatings was evaluated under dry sliding wear test condition at room temperature. Owing to the presence of hard α-Al2O3 and γ-Al2O3 phases, the coatings exhibited excellent wear resistance. In addition, the wear resistance of the coatings fabricated by two-step method is superior to that of the coatings fabricated by one-step method.

Microstructure and Wear Resistance of Laser Clad Cobalt-Based Alloy/SiC_p Composite Coating

The SiCp(20 %)reinforced cobalt-based alloy composite coatings deposited by laser cladding on IF steel were introduced.The microstructure across the whole section of such coatings was examined using optical microscope,scanning electron microscope(SEM)and X-ray diffractometer(XRD),and the wear resistance of the coatings was measured by MM-200 type wear testing machine.The results show that the SiCpis completely dissolved during laser cladding and the primary phase in the coatings isγ-Co.The other phases,such as Si2 W,CoWSi,Cr3 Si and CoSi2,are formed by carbon,silicon reacting with other elements existing in the melting pool.There are various crystallization morphologies in different zones,such as planar crystallization at the interface,followed by cellular and dendrite crystallization from interface to the surface.The direction of solidification changes from one direction perpendicular to interface to multi-directions at the central and upper regions of the clad.The wear resistance of the clad is improved by adding SiCp.

Microstructure and wear resistance of AlCrFeNiMo_(0.5)Si_(x) high-entropy alloy coatings prepared by laser cladding

In recent years,the coating prepared by laser cladding has attracted much attention in the field of wear research.In this work,AlCrFeNiMo_(0.5)Si_(x)(x=0,0.5,1.0,1.5,2.0)high-entropy alloy coatings were designed and prepared on Q235 steel by laser cladding.The effect of Si content on microstructure,microhardness and wear resistance of the coatings was studied in detail.The results indicate that the AlCrFeNiMo_(0.5)Si_(x) highentropy alloy coatings show an excellent bonding between substrate and the cladding layer.The AlCrFeNiMo_(0.5)Si_(x) coatings are composed of nano-precipitated phase with BCC structure and matrix with ordered B2 structure.With the addition of Si,the white phase(Cr,Mo)_(3)Si with cubic structure appears in the interdendritic,and the morphology of the coating(x=2.0)transforms into lamellar eutectic-like structures.The addition of Si enhances the microhardness and significantly improves the wear resistance of the coatings.As x increases from 0 to 2.0,the average hardness of the cladding zone increases from 632 HV to 835 HV,and the wear rate decreases from 1.64×10^(-5) mm^(3)·(N·m)^(-1) to 5.13×10^(-6) mm^(3)·(N·m)^(-1).When x≥1.5,the decreasing trend of the wear rate gradually slows down.The wear rates of Si1.5 and Si2.0 coatings are 5.85×10^(-6) mm^(3)·(N·m)^(-1) and 5.13×10^(-6) mm^(3)·(N·m)^(-1),respectively,which is an order of magnitude lower than that of Q235 steel.

Laser Cladding Al-Si/Al_2O_3-TiO_2 Composite Coatings on AZ31B Magnesium Alloy

To improve the wear resistance and corrosion resistance of magnesium alloys, a 5 kW continuous wave CO2 laser was used to investigate the laser surface cladding on AZ31 B magnesium alloys with Al-Si/Al2O3-TiO2 composite powders. A detailed microstructure, chemical composition, and phase analysis of the composite coatings were studied by scanning electron microscopy （SEM）, energy dispersive spectroscopy （EDS）, and X-ray diffraction （XRD）. The laser cladding shows good metallurgical bonding with the substrate. The composite coatings are composed of Mgl7Al12, Al3Mg2, Mg2Si, Al2O3, and TiO2 phases. Compared to the average microhardness （50HV0.05） of the AZ3 1 B substrate, that of the composite coatings （230HV0.05） is improved significantly. The wear resistances of the surface layers were evaluated in detail. The results demonstrate that the wear resistances of the laser surface-modified samples are considerably improved compared to the substrate. It also show that the composite coatings exhibit better corrosion resistance than that of the substrate in 3.5wt% NaCI solution.

Microstructure and wear resistance of laser clad TiB-TiC/TiNi-Ti_2Ni intermetallic coating on titanium alloy

A wear resistant TiB-TiC reinforced TiNi-Ti2Ni intermetallic matrix composite coating（TiB-TiC/TiNi-Ti2Ni） was prepared on Ti-6.5Al-2Zr-1Mo-1V titanium alloy by the laser cladding process using Ti＋Ni＋B4C powder blends as the precursor materials.Microstructure and worn surface morphologies of the coating were characterized by optical microscopy（OM）,scan electron microscopy（SEM）,X-ray diffraction（XRD）,energy dispersive X-ray analysis（EDS） and atomic force microscopy（AFM）.Wear resistance of the coating was evaluated under dry sliding wear test condition at room temperature.The results indicate that the laser clad coating has a unique microstructure composed of flower-like TiB-TiC eutectic ceramics uniformly distributed in the TiNi-Ti2Ni dual-phase intermetallic matrix.The coating exhibits an excellent wear resistance because of combined action of hard TiB-TiC eutectic ceramic reinforcements and ductile TiNi-Ti2Ni dual-phase intermetallic matrix.

Microstructure and Wear Behaviour of Laser-induced Thermite Reaction Al_2O_3 Ceramic Coating on AA7075 Aluminum Alloy

The microstructure and wear behaviour of the thermite reaction coating produced by the hybrid laser claddingremelting on AA7075 aluminum alloy for the systems of Al-CuO-SiO2, Al-Cr2O3-SiO2, Al-Fe2O3-SiO2, and Al-TiO2-SiO2 were studied. The results of the X-ray diffraction （XRD） analysis show that in all the four reaction coatings, α-Al2O3 and γ-Al2O3 phases were present at the top surface, together with various intermetallic phases, the corresponding reduced metal and Al phase in the fusion zone. Under the dry sliding condition, the wear resistance, in terms of weight loss, of the laser-clad specimens was considerably higher than that of the untreated specimen. The predominant wear mechanism of the former specimens was abrasive wear, while for the latter, it was the adhesive wear that prevailed.

Microstructure and properties of WC-12Co composite coatings prepared by laser cladding

A comprehensive study of the phase composition, microstructure evolution, microhardness and wear performance of WC-12 Co composite coatings fabricated by laser cladding using coaxial powder-feed mode was presented. It was shown that a combination of high scan speed and high laser energy density made WC on the edge of WC-12 Co composite powders partially melt in liquid Co and 304 stainless steel matrix, and then new carbides consisting of lamellar WC and herringbone M3 W3 C(M=Fe,Co) were formed. Meanwhile, WC-12 Co composite coatings with no porosity, cracks and drawbacks like decarburization were obtained, showing high densification and good metallurgical bonding with the substrate. Furthermore, a considerably high microhardness of HV0.3 1500-1600, low coefficient of friction of 0.55 and wear rate of(2.15±0.31)×10-7 mm3/(N·m) were achieved owing to the synergistic effect of excellent metallurgical bonding and fine microstructures of composite coating under laser power of 1500 W.

Influence of laser scanning speed on Cu-Zr-Al composite coatings on Mg alloys

To improve the surface properties of magnesium alloys, a study was conducted on Cu-Zr-A1 composite coatings on AZ91HP magnesium alloy by laser cladding. The influence of laser scanning speed on the microstructures and properties of the coatings was discussed. The coatings consist of amorphous phase, CusZr3, and Cul0ZrT. With the increase of laser scanning speed, the amorphous phase content of the coatings increases and reaches 60.56wt% with the laser scanning speed of 2.0 m/min. Because of the influence of laser scanning speed on the amorphous and crystal phases, the coatings show the maximum elastic modulus, hardness, and wear resistance at the laser scanning speed of 1.0 m/min. At the laser scanning speed of 2.0 m/min, the coatings have the best corrosion resistance.

Structural characteristics and high-temperature tribological behaviors of laser cladded NiCoCrAlY−B_(4)C composite coatings on Ti6Al4V alloy

In order to improve the hardness and tribological performance of Ti6Al4V alloy,NiCoCrAlY-B_(4)C composite coatings with B_(4)C of 5%,10%and 15%(mass fraction)were fabricated on its surface by laser cladding(LC).The morphologies,chemical compositions and phases of obtained coatings were analyzed using scanning electronic microscope(SEM),energy dispersive spectrometer(EDS),and X-ray diffraction(XRD),respectively.The effects of B_(4)C mass fraction on the coefficient of friction(COF)and wear rate of NiCoCrAlY-B_(4)C coatings were investigated using a ball-on-disc wear tester.The results show that the NiCoCrAlY-B_(4)C coatings with different B_(4)C mass fractions are mainly composed of NiTi,NiTi_(2),α-Ti,CoO,AlB_(2),TiC,TiB and TiB_(2)phases.The COFs and wear rates of NiCoCrAlY-B_(4)C coatings decrease with the increase of B_(4)C content,which are contributed to the improvement of coating hardness by the B_(4)C addition.The wear mechanisms of NiCoCrAlY-B_(4)C coatings are changed from adhesive wear and oxidation wear to fatigue wear with the increase of B_(4)C content.

Microstructure and Tribological Properties of In-situ Synthesized TiB_2- TiC /Ni Based Composite Coating by Laser Cladding

A TiB2 and TiC particles reinforced Ni based composites coating was prepared on TC4 alloy surface by chemical reaction among Ti, B and C elements using laser cladding technique. Microstructural analysis showed that the sizes of in-situ synthesized TiB2 and TiC particles ranged within 5~10um and l^2um, respectively, while both the two kinds of particles were uniformly distributed in the clad layer. The measurement of microhardness and wear and friction properties indicated that the microhardness of laser clad layer was HV900-1100, being three times of that of the TC4 alloy; the friction coefficient of the laser clad layer in air and in vacuum (10~5 Pa) ranged within 0.2-0.3 and 0.3-0.5, respectively; the wear rate in terms of mass loss was considerably lower than that of the TC4 alloy both in air and in vacuum environment.

Fabrication and microstructure of Fe-based amorphous composite coatings by laser cladding

Fe-based amorphous composite coatings were fabricated on AISI 1045 steel by laser cladding. The results of the X- ray diffraction and transmission electron microscopy analyses .show the coating is composed of an amorphous phase in majority and a nanocrystaUine phuse in m,inority. Phase composition of the coating changes along the depth of the coating. The reasonable scanning speed for fabricating an amorphous composite coating is 3 500 mm/min when the laser power is 4 800 W and the laser beam diameter is 2 mm. If the scanning speed is lower than 3 500 mm/min, the intensity of the two main diffraction peaks in X-ray diffraction patterns of the coatings decreases with the scanning speeds increasing. At the same time, a broad halo peak emerges and enlarges. High laser power and fast scanning speed are the essential conditions of amorphization. The coating exhibits high microhardness.

Effect of Fe content on microstructure and mechanical properties of Cu-Fe-based composite coatings by laser induction hybrid rapid cladding

To select the proper composition and obtain an overall material?microstructure?property relationship for Cu?Fe alloy, theeffect of Fe content on microstructure and properties of Cu?Fe-based composite coatings by laser induction hybrid rapid claddingwas investigated. Microstructure characterization of the composite coatings was tested utilizing SEM, XRD and EDS. Microhardnessmeasurement was executed to evaluate the mechanical properties of the composite coatings. The results show that for low Fe content,the composite coating presents a feature that Fe-rich equiaxed dendrites are embedded in the Cu-rich matrix. With increasing Fecontent, the Fe-rich particles are dispersed in the Cu-rich matrix. With further increasing Fe content, large amounts of Cu-richparticles are homogeneously dispersed in the interdendrite of the Fe-rich matrix. Correspondingly, the average microhardness of thecomposite coatings increases gradually with the increase of Fe content and the microhardness of Cu14.5Fe83Si2C0.5 coating is muchtwice higher than that of the substrate.

WIDE-BAND LASER CLADDING: WEAR AND CORROSION RESISTANCE OF A Ni-BASED ALLOY

A novel wide-band laser cladding system, with high rate of cladding, has been developed in the present work. The system mainly consisted of a 5kW CO2 laser, an automatic powder feeder and a wide-band scanning rotative polygon mirror which can produce a linear or rectangular focused laser beam. Using this system, a Ni-Cr-Si-B alloy powder was cladded on the surface of type 321 austenitic stainless steel in order to improve its wear and corrosion resistance. The pitting corrosion, high temperature oxidation and wear tests were conducted in order to evaluate the properties of the laser cladded layer. The results demonstrated that the cladded layer can significantly improve the adhesive wear and pitting corrosion resistance of the substrate. Moreover, the cladded layer exhibited good oxidation resistance, which is almost the same as that of GMR-235D Ni-based superalloy.

Coarse WC Particles Ceramic-Metal Composite Coating by Laser Cladding

The coarse WC particles ceramic-metal com- posite coatings with WC density of 67 wt-% and thickness of 1.0-1.2 mm have been cladded on 20Ni4Mo steel surface by a 2 kW CO_2 laser.The sintered WC particles with the size of 600-1000 μm are chosen as the main strengthening phase, Ni-base self-flux alloy as the binder in the compo- site coatings.The microstructure and microhardness of both WC particles and binder are analysed.The rigid ball indention with acoustic emission technique is used to evaluate the brittleness of the coating.Finally,the abrasive wear resistance of the coating is tested.Besides,the coatings with the same ratio and size of WC parti- cles in low carbon steel tube rod were cladded on 20Ni4Mo steel by atomic hydrogen welding tech- nique and analysed by the same way,their results are compared.

Microstructure and Sliding Wear Property of Laser Clad TiN－Reinforced Composite Coating

The microstructure and sliding wear property of laser clad TiN-composite coating on steel 1045 were analyzed by SEM, EPMA, XRD, EDAX techniques and a pin-on-ring dry sliding wear testing machine. An excellent fusion bonding with low dilution and absence of cracks was obtained under the laser cladding conditions of specific energy and power density in the range 5 to 20kJ/cm￣2 and 3.5 to 5kW/cm￣2 respectively. The clad layers have been characterized by metallurgical examination. The bonding zone about 6μm thick is analyzed to be γ-Ni solid solution growing from the bottom of molten pool in the form of planar crystal morphology. γ-Ni, TiN particles and fine eutectic of γ-Ni+(Fe, Cr)_(23)C_6, in the interdendritic regions are observed. A large number of TiN particles in irregular shapes are remained afer laser cladding. Partial dissolution appearing on the edges of original TiN particulates and their growth during resolidification are found in the clad region. The TiN-reinforced composite coating produced by laser cladding possesses a good wear resistance n this study. An adhesive wear with a regular scale-like feature on the worn surface was observed.

Effect of process parameters on the microstructure and properties of laser-clad FeNiCoCrTi0.5 high-entropy alloy coating

FeNiCoCrTi0.5 coatings with different process parameters were fabricated by laser cladding. The macro-morphology, phase, microstructure, hardness, and wear resistance of each coating were studied. The smoothness and dilution rate of the FeNiCoCrTi0.5 coating generally increased with the increase of specific energy(Es), which is the laser irradiation energy received by a unit area. FeNiCoCrTi0.5 coatings at different parameters had bcc, fcc, and Ti-rich phases as well as equiaxed, dendritic, and columnar structures. When Es increased, the size of each structure increased and the distribution area of the columnar and dendritic structures changed. The prepared FeNiCoCrTi0.5 coating with the Es of 72.22 J·mm-2 had the highest hardness and the best wear resistance, the highest hardness of the coating reached HV 498.37, which is twice the substrate hardness. The average hardness of the FeNiCoCrTi0.5 coating with the Es of 72.22 J·mm-2 was 15.8% higher than the lowest average hardness of the coating with the Es of 108.33 J·mm-2. The worn surface morphologies indicate that the FeNiCoCrTi0.5 coatings exhibited abrasive wear.

Laser in-situ synthesis of titanium matrix composite coating with TiB-Ti network-like structure reinforcement

To avoid high crack sensitivity of TiB-Ti composite coating during laser cladding process,network-like structure composite coating was fabricated with laser in-situ technique on titanium alloy using 5 μm TiB2 powder as the cladding material.The microstructure,phase structure and properties of the coatings were analyzed by SEM,XRD,EPMA,TEM,hardness tester and fretting wear meter.It was observed that the outer ring of the network-like structure was mainly TiB strengthening phase,while the inner ring was α-Ti grain,and the interface between TiB and Ti matrix was very clean and had a consistent orientation relationship.The hardness of the cladding layer with network-like structure gradually decreased from the surface toward the interface,but the average hardness was nearly two times that of the substrate.In the fretting wear test,it was found that the wear resistance of the cladding layer with network-like structure was larger than that of the substrate under low load(40 N).The results revealed that the hardness and fretting wear resistance of the titanium-based composite coating could be improved by the introduction of network-like structure.

Laser cladding of Ti-6Al-4V titanium alloy with Ti+TiC powders

TiC/Ti composite layers were produced by laser melting the preplaced mixture of Ti and TiC powders. The results show that the microstructure, microhardness and wear resistance of the clad layer are all evaluated. The composite layer consists of TiC and α-Ti phases. TiC in the clad zone exists in the form of fine dendrites and Ti fills among TiC dendrites, which has a typical structure of TiC/Ti composite. The microhardness of the composite coating is significantly enhanced as high as HV_ 0.2940 as compared to HV_ 0.2345 of the substrate region. The composite layer has excellent wear resistance compared to titanium alloy.

High temperature frictional wear behaviors of nano-particle reinforced NiCoCrAlY cladded coatings

The NiCoCrAlY coatings strengthened by three nano-particles with the same addition were prepared on a Ni-base super alloy using laser cladding technique. The dry frictional wear behaviors of the coatings at 500 ℃ in static air were investigated. The comparison was made with the coating without nano-particles. The results show that the wear mechanism of the NiCoCrAlY coatings with nano-particles, like the coating without nano-particles, is the delamination wear due to the strong plastic deformation and oxidative wear. However, the frictional coefficient of the coatings increases and presents the decrease trend with the increase of sliding distance after adding nano-particles. Moreover, the wear rate of the coatings with nano-particles is only 34.0%-64.5% of the coating without nano-particles. Among the three nano-particles, the improvement of nano-SiC on the high temperature wear resistance of the coating is the most significant.