A 10 Gb/s laser diode driver in 0.35 μm SiGe BiCMOS technology

This paper discusses the design of a 10 Gb/s laser diode driver implemented in SiGe BiCMOS technology. The laser diode driver is composed of an input buffer, a predriver circuit and an output current switch stage. With the current mode logic （CML） structure, the input buffer and the predriver circuit have the capability of transmission and amplification of high speed data. By employing MOS-HBT cascode structure as the output stage, the laser diode driver exhibits very high speed and efficiency working at the 10 Gb/s data rate. The core circuit is operated under a 3. 3 V supply, while the output stage is operated under 5.5 V for sufficient headroom across the laser diode. The chip occupies a die area of 600 μm × 800μm. Measurements on chip show clear electrical eye diagrams over 10 Gb/s, which can well meet the specifications defined by SDH STM64/SONET OC192 and a 10 Gb/s Ethemet eye mask. Under a 5. 5 V supply voltage, the maximum output swing is 3.0 V with a 50 12 load （the corresponding modulation current is 60 mA）, and the total power dissipation is 660 mW.

Slope excavation quality assessment and excavated volume calculation in hydraulic projects based on laser scanning technology

Slope excavation is one of the most crucial steps in the construction of a hydraulic project. Excavation project quality assessment and excavated volume calculation are critical in construction management. The positioning of excavation projects using traditional instruments is inefficient and may cause error. To improve the efficiency and precision of calculation and assessment, three-dimensional laser scanning technology was used for slope excavation quality assessment. An efficient data acquisition, processing, and management workflow was presented in this study. Based on the quality control indices, including the average gradient, slope toe elevation, and overbreak and underbreak,cross-sectional quality assessment and holistic quality assessment methods were proposed to assess the slope excavation quality with laserscanned data. An algorithm was also presented to calculate the excavated volume with laser-scanned data. A field application and a laboratory experiment were carried out to verify the feasibility of these methods for excavation quality assessment and excavated volume calculation. The results show that the quality assessment indices can be obtained rapidly and accurately with design parameters and scanned data, and the results of holistic quality assessment are consistent with those of cross-sectional quality assessment. In addition, the time consumption in excavation quality assessment with the laser scanning technology can be reduced by 70%e90%, as compared with the traditional method. The excavated volume calculated with the scanned data only slightly differs from measured data, demonstrating the applicability of the excavated volume calculation method presented in this study.

A 15 Gbps-NRZ, 30 Gbps-PAM4, 120 mA laser diode driver implemented in 0.15-μm GaAs E-mode pHEMT technology

This paper presents the design and testing of a 15 Gbps non-return-to-zero(NRZ),30 Gbps 4-level pulse amplitude modulation(PAM4)configurable laser diode driver(LDD)implemented in 0.15-μm GaAs E-mode pHEMT technology.The driver bandwidth is enhanced by utilizing cross-coupled neutralization capacitors across the output stage.The output transmission-line back-termination,which absorbs signal reflections from the imperfectly matched load,is performed passively with on-chip 50-Ωresistors.The proposed 30 Gbps PAM4 LDD is implemented by combining two 15 Gbps-NRZ LDDs,as the high and low amplification paths,to generate PAM4 output current signal with levels of 0,40,80,and 120 mA when driving 25-Ωlasers.The high and low amplification paths can be used separately or simultaneously as a 15 Gbps-NRZ LDD.The measurement results show clear output eye diagrams at speeds of up to 15 and 30 Gbps for the NRZ and PAM4 drivers,respectively.At a maximum output current of 120 mA,the driver consumes 1.228 W from a single supply voltage of-5.2 V.The proposed driver shows a high current driving capability with a better output power to power dissipation ratio,which makes it suitable for driving high current distributed feedback(DFB)lasers.The chip occupies a total area of 0.7×1.3 mm^(2).

New Progress on All Solid State Laser Technology in China

1 Significance of All Solid State Laser (DPL) Technology in Field of LaserBecause of the advantages of high conversion efficiency, good beam quality, small size and light weight, DPL becomes the hotspot and priority of development of laser technology. It may be the main body of laser in the future and replace gas laser and liquid laser. It is a great revolution of laser technology.The developed countries vie in developing DPL. China has achieved great success in this field, but there is a wide gap between the developed countries and us. We should attach great importance to it.

Re-Heating Effect on the Enhancement of Plasma Emission Generated from Fe Under Femtosecond Double-Pulse Laser Irradiation

In this paper, we present a study on the effect of inter-pulse delay using femtosecond double-pulse laser-induced breakdown spectroscopy in a collinear geometry. The temporal evolution of spectral intensity is performed for the lines of Fe I 423.60 nm, Fe I 425.08 nm and Fe I 427.18 nm. It is found that, by selecting appropriate inter-pulse delay, the signal enhancement can be significantly increased compared with the single-pulse case. A three-fold enhancement in the current experiment is obtained. The plasma temperature and electron density are also investigated based on the theory of Boltzmann plot and Stark broadening. We attribute the main mechanism for emission enhancement to the plasma re-heating effect.

Recent Research and Development Status of Relaxed Optics and Laser Technology: A Review

It is shown that for laser technologies it was necessary to create a new branch of physics: Relaxed Optics (synthesis of methods of the physical optics, quantum electronics, physical chemistry, physics of irreversible phenomena in unitary system). It is allowed to explain complex chain processes of interaction light and matter. Possible applications of Relaxed Optical methods for the modeling of the laser-induced processes phenomena, including laser implantation (surface and subsurface processes), laser-induced optical breakdown (volume processes) and laser annealing of radiation and other defects in solid, are discussed. Perspectives of using these methods for the creation of new laser technologies, including creation new types of optoelectronic devices (heterostructures, diffraction lattices, etc.), resolution the problems of metallurgy, material science, painting, architecture and a building, are analyzed.

Preface to the special issue on laser processing and micro-nano technology

In 2022, coinciding with the 20th anniversary of the School of Physics and Electronics at Central South University, we plan to publish the special issue “Laser processing and micro-nano technology” in the Journal of Central South University, which aims to commemorate the 20th anniversary of the school and comprehensively present the latest achievement in the fields of laser processing and micro-nano technology to domestic and foreign universities.

Blood–brain barrier and laser technology for drug brain delivery

Here,we discuss an important problem in medicine as development of efctive strategies for brain drug delivery.This problem is related to the blood-brain barrier(BBB),which is a“customs”controlling the entrance of different molecules from blood into the brain protecting the normal function of central nervous system(CNS).We show three interfaces of anatomical side of BBB and two functional types of BBB一physical and transporter barriers.Although this protective mechanism is essential for health of CNS,it also creates a hindrance to the entry of drugs into the brain.The BBB was discovered over 100 years ago but till now,there is no efective methods for brain drug delivery.There ane more than 70 approaches for overcoming BBB incuding physical,chenical and biological techniques but all of these tools have limitation to be widely used in clinical practice due to invasi venes,challenge in performing,very costly or lim-itation of drug concentration.Photodynamic therapy(PDT)is usual clinical method of surgical navigation for the resection of brain tumor and anti-cancer therapy.Nowadays,the application of PDT is considered as a potential promising tool for brain drug delivery via opening of BBB.Here,we show the first sucoessful experimental results in this field discussing the adventures and disadv antages of PDT-related BBB disruption as well as altematives to overcome these limitations and possi ble mechanisms with new pathways for brain clearance via gly mphatic and lymphatic systems.

Research on wind erosion processes and controlling factors based on wind tunnel test and 3D laser scanning technology

The study of wind erosion processes is of great importance to the prevention and control of soil wind erosion.In this study,three structurally intact soil samples were collected from the steppe of Inner Mongolia Autonomous Region,China and placed in a wind tunnel where they were subjected to six different wind speeds(10,15,17,20,25,and 30 m/s)to simulate wind erosion in the wind tunnel.After each test,the soil surfaces were scanned by a 3D laser scanner to create a high-resolution Digital Elevation Model(DEM),and the changes in wind erosion mass and microtopography were quantified.Based on this,we performed further analysis of wind erosion-controlling factors.The study results showed that the average measurement error between the 3D laser scanning method and weighing method was 6.23%for the three undisturbed soil samples.With increasing wind speed,the microtopography on the undisturbed soil surface first became smooth,and then fine stripes and pits gradually developed.In the initial stage of wind erosion processes,the ability of the soil to resist wind erosion was mainly affected by the soil hardness.In the late stage of wind erosion processes,the degree of soil erosion was mainly affected by soil organic matter and CaCO_(3)content.The results of this study are expected to provide a theoretical basis for soil wind erosion control and promote the application of 3D laser scanners in wind erosion monitoring.

Innovations in Retinal Laser Technology

Retinal laser photocoagulation is a proven, effective treatment for various retinal disorders, including diabetic retinopathy, retinal vein occlusions, and sickle cell retinopathy. To minimize iatrogenic retinal damage while maintaining therapeutic effects, retinal laser technology has evolved significantly since its introduction in ophthalmology more than half a century ago. These innovations have included both optimizations of laser parameters in addition to the development of novel laser delivery systems. This review summarizes recent innovations in retinal laser technology, including subthreshold micropulse laser, selective retinal therapy and nanosecond laser, innovative modes of laser delivery including pattern scanning laser, endpoint management, navigated laser, and newly described photo-mediated ultrasound therapy.

A Single Mode Hybrid Ⅲ-Ⅴ/Silicon On-Chip Laser Based on Flip-Chip Bonding Technology for Optical Interconnection

A single mode hybrid Ⅲ-Ⅴ/silicon on-chip laser based on the flip-chip bonding technology for on-chip optical interconnection is demonstrated. A single mode Fabry-Perot laser structure with micro-structures on an InP ridge waveguide is designed and fabricated on an InP/AIGaInAs multiple quantum well epitaxial layer structure wafer by using i-line lithography. Then, a silicon waveguide platform including a laser mounting stage is designed and fabricated on a silicon-on-insulator substrate. The single mode laser is flip-chip bonded on the laser mounting stage. The lasing light is butt-coupling to the silicon waveguide. The laser power output from a silicon waveguide is 1.3roW, and the threshold is 37mA at room temperature and continuous wave operation.

Tungsten ion source under double-pulse laser ablation system

New tungsten ion source is produced by using single and double-pulse laser ablation system. Combined collinear Nd：YAG laser beams（266＋1064 nm） are optimized to focus on the sample in air. Optimization of the experimental parameters is achieved to enhance the signal-to-noise ratio of the emission spectra. The velocity distribution of the emitted plasma cloud is carefully measured. The influences of the potential difference between the bias electrodes, laser wavelength and intensity on the current signal are also studied. The results show that the increase in the tungsten ion velocity under the double-pulse lasers causes the output current signal to increase by about three folds. The electron density and temperature are calculated by using the Stark-broadened line profile of tungsten line and Boltzmann plot method of the upper energy levels, respectively. The signal intensity dependence of the tungsten ion angular distribution is also analyzed. The results indicate that the double-pulse laser ablation configuration is more potent technique for producing more metal ion source deposition, thin film formation, and activated plasma-facing component material.

Fabrication of 32 Gb/s Electroabsorption Modulated Distributed Feedback Lasers by Selective Area Growth Technology

A 32 Gb/s monolithically integrated electroabsorption modulated laser is fabricated by selective area growth technology. The threshold current of the device is below 13mA. The output power exceeds 10mW at 0V bias when the injection current of the distributed feedback laser is 100mA at 25℃. The side mode suppression ratio is over 50 dB. A 32Gb/s eye diagram is measured with a 3.SVpp nonreturn-to-zero pseudorandom modulation signal at -2.3 V bias. A clearly opening eyediagram with a dynamic extinction ratio of 8.01 dB is obtained.

Hybrid Laser Technology for Creation of Doped Biomedical Layers

Hybrid laser technologies for deposition of thin films and basic schemes of combination of pulsed laser deposition (PLD) with magnetron sputtering and RF discharges or two lasers or three laser deposition systems are presented. Experiences with deposition of chromium doped diamond-like carbon (DLC) films for coating of prostheses are described. Layers of different chromium concentrations were prepared using hybrid systems (PLD + magnetron sputtering or by double PLD). Results of physical and mechanical characterization of film properties and biomedical tests of trivalent and toxic hexavalent chromium are given. Experiences with double laser deposition of DLC layers doped with silver are also mentioned.

Research on 3D Laser Scanning Reconstruction of Ancient Buildings Combined with BIM Technology

After more than 30 years of scientific and social development, surveying and mapping technology by leaps and bounds, engineering surveying technology has undergone tremendous changes. In the process of protecting ancient buildings, it is necessary to obtain the precise dimensions of architectural details. In this study, the path of 3D laser scanning combined with BIM technology is explored. Taking the observation and protection of the ancestral hall of the Liu family as an example, this study aims to draw drawings that reflect the relevant information about the ancient buildings, the accurate three-dimensional model of ancient buildings is established with BIM technology, which provides new methods and ideas for the research and protection of ancient buildings. .

Application of Three-dimensional Laser Scanning Technology in the Teaching Practice of Surveying and Mapping of Ancient Buildings

Based on the study of the application of three-dimensional laser scanning technology in ancient building surveying and mapping,this paper briefly describes the working principle and flow of three-dimensional laser scanning technology.Based on the practical application,this paper puts forward the discussion of related problems and matters needing attention.This has a certain reference significance for the study of new technology in surveying and mapping of ancient buildings.

Laser Technology and Equipment

5W CW Diode-Pumped Solid-State Green Laser；QCW Diode-Pumped Solid-State Green Laser；High Beam Quality Diode-Pumped In-Frared Laser；High Beam Quality Diode-Pumped Infrared Laser；QCW Diode-Pumped Solid-State UV Laser；

The Research Application of 3D Laser Scanning Technology in the Deformation Detection of Large Cylindrical Oil Tank

In order to ensure the safety in using a large cylindrical storage tank,it is necessary to regularly detect its defonnatioii.The traditional total station method has high accuracy in determining the deformation,however,it has a low measxirement efficiency.Long-term observation means,there are more risks in the petrochemical plant,therefore,this paper proposes the usage of the 3D laser scanner,replacing the traditional total station to determine the defbnnation of a large cylindrical storage tank.The Matlab program,is compiled to calculate the point cloud data,while the tank deformation is analyzed from two different points which are,the local concave convex degree and the ovality degree.It is concluded that,the difference between the data obtained by 3D laser scanning,and total station is within the range of oil tank deformation limit,therefore,3D laser scanner can be used for oil tank deformation detection.

The development of 3D printing technology and the current situation of controlling defects in SLM technology

With unique manufacturing technology,the additive manufacturing technology divides the three-dimensional object into countless two-dimensional laminates.Compared with the traditional material reduction manufacturing method,it has the characteristics of saving materials,being fast,and especially suitable for single and small batch parts and the rapid manufacturing of parts with complex shapes and internal structures.In this paper,various methods of additive manufacturing technology are reviewed.This paper introduces the characteristics of selective laser melting technology and its forming equipment system.On this basis,the technical defects of selective laser melting technology are analyzed,and the status of controlling defects in SLM technology is explained.In the end,the prospects of additive manufacturing technology are described.