Electrochemical performance of carbon nanotube-modified LiFePO_4 cathodes for Li-ion batteries

Carbon nanotubes (CNTs) and acetylene black (AB) were dispersed synchronously or separately between LiFePO4 (LFP) particles as conducting agents during the course of manufacture of LiFePO4 cathodes. The morphology and electrochemical performances of as-prepared LiFePO4 were evaluated by means of transmission electron microscopy (TEM), charge-discharge test, electrochemical impedance spectroscope (EIS) and cyclic voltammetry (CV). CNTs contribute to the interconnection of the isolated LiFePO4 or carbon particles. For the CNTs-modified LiFePO4, it exhibits excellent performance in terms of both specific capacity and cycle life. The initial discharge capacity is 147.9 mA·h/g at 0.2C rate and 134.2 mA·h/g at 1C rate, keeping a capacity retention ratio of 97% after 50 cycles. The results from EIS indicate that the impedance value of the solid electrolyte interface decreases. The cyclic voltammetric peak profiles is more symmetric and spiculate and there are fewer peaks. CNTs are promising conductive additives candidate for high-power Li-ion batteries.

Synthesis and electrochemical performances of spherical LiFePO_4 cathode materials for Li-ion batteries

Spherical LiFePO4 and LiFePO4/C composite powders for lithium ion batteries were synthesized by a novel processing route of co-precipitation and subsequent calcinations in a nitrogen and hydrogen atmosphere. The precursors of LiFePO4, LiFePO4/C composite and the resultant products were characterized by X-ray diffraction (XRD), scanning electron microscope (SEM), and the electrochemical performances were investigated by galvanostatic charge and discharge tests. The precursors composed of amorphous Fe3(PO4)2·xH2O and crystalline Li3PO4 obtained in the co-precipitation processing have a sphere-like morphology. The spherical LiFePO4 derived from the calcinations of the precursor at 700 ℃ for 10 h in a reduction atmosphere shows a discharge capacity of 119 mAh·g-1 at the C/10 rate, while the LiFePO4/C composite with 10wt.% carbon addition exhibits a discharge capacity of 140 mAh·g-1. The electrochemical performances indicate that the LiFePO4/C composite has a higher specific capacity and a more stable cycling performance than the bare olivine LiFePO4 due to the carbon addition enhancing the electronic conductivity.

Controllable synthesis of high loading LiFePO_4/C nanocomposites using bimodal mesoporous carbon as support for high power Li-ion battery cathodes

Mesoporous LiFePO4/C composites containing 80 wt% of highly dispersed LiFePO4 nanoparticles(4-6 nm) were fabricated using bimodal mesoporous carbon(BMC) as continuous conductive networks. The unique pore structure of BMC not only promises good particle connectivity for LiFePO4, but also acts as a rigid nano-confinement support that controls the particle size. Furthermore, the capacities were investigated respectively based on the weight of LiFePO4 and the whole composite. When calculated based on the weight of the whole composite, it is 120 mAh·g-1at 0.1 C of the high loading electrode and 42 mAh·g-1at 10 C of the low loading electrode. The electrochemical performance shows that high LiFePO4 loading benefits large tap density and contributes to the energy storage at low rates, while the electrode with low content of LiFePO4 displays superior high rate performance, which can mainly be due to the small particle size, good dispersion and high utilization of the active material, thus leading to a fast ion and electron diffusion.

Electrochemical performance of LiFePO_4 cathode material for Li-ion battery

In the search for improved materials for rechargeable lithium batteries, LiFePO4 offers interesting possibilities because of its low raw materials cost, environmental friendliness and safety. The main drawback with using the material is its poor electronic conductivity and this limitation has to be overcome. Here Al-doped LiFePO4/C composite cathode materials were prepared by a polymer-network synthesis technique. Testing of X-ray diffraction, charge-discharge, and cyclic voltammetry were carried out for its performance. Results show that Al-doped LiFePO4/C composite cathode materials have a high initial capacity, good cycle stability and excellent low temperature performance. The electrical conductivity of LiFePO4 material can be obviously improved by doping Al. The better electrochemical performances of Al-doped LiFePO4/C composite cathode materials have a connection with its conductivity.

The Surface Coating of Commercial LiFePO_4 by Utilizing ZIF-8 for High Electrochemical Performance Lithium Ion Battery

The requirement of energy-storage equipment needs to develop the lithium ion battery(LIB) with high electrochemical performance. The surface modification of commercial LiFePO_4(LFP) by utilizing zeolitic imidazolate frameworks-8(ZIF-8) offers new possibilities for commercial LFP with high electrochemical performances.In this work, the carbonized ZIF-8(C_(ZIF-8)) was coated on the surface of LFP particles by the in situ growth and carbonization of ZIF-8. Transmission electron microscopy indicates that there is an approximate 10 nm coating layer with metal zinc and graphite-like carbon on the surface of LFP/C_(ZIF-8) sample. The N_2 adsorption and desorptionisotherm suggests that the coating layer has uniform and simple connecting mesopores. As cathode material, LFP/C_(ZIF-8) cathode-active material delivers a discharge specific capacity of 159.3 m Ah g^(-1) at 0.1 C and a discharge specific energy of 141.7 m Wh g^(-1) after 200 cycles at 5.0 C(the retention rate is approximate 99%). These results are attributed to the synergy improvement of the conductivity,the lithium ion diffusion coefficient, and the degree of freedom for volume change of LFP/C_(ZIF-8) cathode. This work will contribute to the improvement of the cathode materials of commercial LIB.

Synthesis and characterization of phosphate-modified LiMn_2O_4 cathode materials for Li-ion battery

LiMn2O4 spinel cathode materials were modified with 2 wt.%Li-M-PO4（M=Co,Ni,Mn） by polyol synthesis method.The phosphate surface-modified LiMn2O4 cathode materials were physically characterized by X-ray diffraction（XRD）,scanning electron microscopy（SEM） and energy dispersive X-ray spectroscopy（EDS）.The charge-discharge test showed that the cycling and rate capacities of LiMn2O4 cathode materials were significantly enhanced by stabilizing the electrode surface with phosphate.

A novel synthetic route for LiFePO_4/C cathode materials by addition of starch for lithium-ion batteries

LiFePO4/Carbon composite cathode material was prepared using starch as carbon source by spray-pelleting and subsequent pyrolysis in N2. The samples were characterized by XRD, SEM, Raman, and their electrochemical performance was investigated in terms of cycling behavior. There has a special micro-morphology via the process, which is favorable to electrochemical properties. The discharge capacity of the LiFePO4.C composite was 170 mAh g-1, equal to the theoretical specific capacity at 0.1 C rate. At 4 C current density, the specific capacity was about 80 mAh g-1, which can satisfy for transportation applications if having a more flat discharge flat.

Facile synthesis of spinel LiNi_(0.5)Mn_(1.5)O_(4) as 5.0 V-class high-voltage cathode materials for Li-ion batteries

LiNi_(0.5)Mn_(1.5)O_(4) and LiMn_(2)O_(4) with novel spinel morphology were synthesized by a hydrothermal and postcalcination process.The synthesized LiMn_(2)O_(4) particles(5–10 lm)are uniform hexahedron,while the LiNi_(0.5)Mn_(1.5)O_(4) has spindle-like morphology with the long axis 10–15 lm,short axis 5–8 lm.Both LiMn_(2)O_(4) and LiNi_(0.5)Mn_(1.5)O_(4) show high capacity when used as cathode materials for Li-ion batteries.In the voltage range of 2.5–5.5 V at room temperature,the LiNi_(0.5)Mn_(1.5)O_(4) has a high discharge capacity of 135.04 mA·h·g^(-1) at 20 mAg^(-1),which is close to 147 mA·h·g^(-1)(theoretical capacity of LiNi_(0.5)Mn_(1.5)O_(4)).The discharge capacity of LiMn_(2)O_(4) is 131.08 mA·h·g^(-1) at 20 mAg^(-1).Moreover,the LiNi_(0.5)Mn_(1.5)O_(4) shows a higher capacity retention(76%)compared to that of LiMn_(2)O_(4)(61%)after 50 cycles.The morphology and structure of LiMn_(2)O_(4) and LiNi_(0.5)Mn_(1.5)O_(4) are well kept even after cycling as demonstrated by SEM and XRD on cycled LiMn_(2)O_(4) and LiNi_(0.5)Mn_(1.5)O_(4) electrodes.

Physical and Electrochemical Properties of Doped LiFePO4 as Cathode Material for Lithium-Ion Batteries

LiFePO4 cathode material was synthesized by a solid-state reaction using doping several elements (Nb5 + ,Zr4 + ). The starting materials were mixed with a high-efficient sander and treated thermally under flowing N2. The samples were characterized by X-ray diffraction (XRD), field-emission gun electron microscopy (FEG), and their electrochemical performance was investigated in the term of cycling behavior. Room temperature discharge capacity about 140.6 mA·h·g-1 was obtained at C/5 rate.

Experimental study on thermal characteristics of LiFePO_4 power batteries

As an important high-energy chemical power source, lithium-ion power batteries come up to application problems of thermal performance, such as extended temperature range and high power charge ＆ discharge. LiFeP04 battery is applied and developed well recently, its charge and discharge experiment at different temperatures and hybrid pulse power characterization （HPPC） test are analyzed, and the optimal temperature range of LiFeP04 battery is put forward. In order to provide experimental suggestion of power battery application and its thermal management, internal resistance, influencing factor of electromotive force and entropy change state of charge （SOC）, battery thermal characteristic of different charge ＆ discharge rates are summarized.

The design and fabrication of Co3O4/Co3V2O8/Ni nanocomposites as high-performance anodes for Li-ion batteries

The CoO/CoVO/Ni nanocomposites were rationally designed and prepared by a two-step hydrothermal synthesis and subsequent annealing treatment. The one-dimensional（1D） CoOnanowire arrays directly grew on Ni foam, whereas the 1D CoVOnanowires adhered to parts of CoOnanowires.Most of the hybrid nanowires were inlayed with each other, forming a 3D hybrid nanowires network.As a result, the discharge capacity of CoO/CoVO/Ni nanocomposites could reach 1201.8 mAh/g after100 cycles at 100 mA/g. After 600 cycles at 1 A/g, the discharge capacity was maintained at 828.1 mAh/g.Moreover, even though the charge/discharge rates were increased to 10 A/g, it rendered reversible capacity of 491.2 mAh/g. The superior electrochemical properties of nanocomposites were probably ascribed to their unique 3D architecture and the synergistic effects of two active materials. Therefore, such CoO/CoVO/Ni nanocomposites could potentially be used as anode materials for high-performance Li-ion batteries.

Preparation of LiFePO_4 for lithium ion battery using Fe_2P_2O_7 as precursor

In order to obtain a new precursor for LiFePO4, Fe2P2O7 with high purity was prepared through solid phase reaction at 650 ℃ using starting materials of FeC2O4 and NH4H2PO4 in an argon atmosphere. Using the as-prepared Fe2P2O7, Li2CO3 and glucose as raw materials, pure LiFePO4 and LiFePO4/C composite materials were respectively synthesized by solid state reaction at 700 ℃ in an argon atmosphere. X-ray diffractometry and scanning electron microscopy（SEM） were employed to characterize the as-prepared Fe2P2O7, LiFePO4 and LiFePO4/C. The as-prepared Fe2P2O7 crystallizes in the Cl space group and belongs to β-Fe2P2O7 for crystal phase. The particle size distribution of Fe2P2O7 observed by SEM is 0.4-3.0 μm. During the Li^＋ ion chemical intercalation, radical P2O7^4- is disrupted into two PO4^3- ions in the presence of O^2-, thus providing a feasible technique to dispose this poor dissolvable pyrophosphate. LiFePO4/C composite exhibits initial charge and discharge capacities of 154 and 132 mA·h/g, respectively.

Synthesis and Properties of Li_2MnSiO_4/C Cathode Materials for Li-ion Batteries

Carbon was coated on the surface of LiMnSiOto improve the electrochemical performance as cathode materials, which were synthesized by the solution method followed by heat treatment at 700 ℃ and the solid-state method followed by heat treatment at 950 ℃. It is shown that the cycling performance is greatly enhanced by carbon coating, compared with the pristine LiMnSiOcathode obtained by the solution method. The initial discharge capacity of LiMnSiO/C nanocomposite is 280.9 m Ah/g at 0.05 C with the carbon content of 33.3 wt%. The reasons for the improved electrochemical performance are smaller grain size and higher electronic conductivity due to the carbon coating. The LiMnSiO/C cathode material obtained by the solid-state method exhibits poor cycling performance, the initial discharge capacity is less than 25 m Ah/g.

A Novel Real-Time State-of-Health and State-of-Charge Co-Estimation Method for LiFePO_4 Battery

The state of charge （SOC） and state of health （SOH） are two of the most important parameters of Li-ion batteries in industrial production and in practical applications. The real-time estimation for these two parameters is crucial to realize a safe and reliable battery application. However, this is a great problem for LiFePO4 batteries due to the large constant potential plateau in the charge/discharge process. Here we propose a combined SOC and SOH co-estimation method based on the experimental test under the simulating electric vehicle working condition. A first-order resistance-capacitance equivalent circuit is used to model the battery cell, and three parameter values, ohmic resistance （Rs）, parallel resistance （Rp） and parallel capacity （Cp）, are identified from a real-time experimental test. Finally we find that Rp and Cp could be utilized to make a judgement on the SOIl. More importantly, the linear relationship between Cp and the SOC is established to make the estimation of the SOC for the first time.

Studies on Electrochemical Property of LiFePO_4/C as Cathode Material for Lithium Ion Batteries

LiFePO4/C samples were prepared at different temperatures by adding sngar to the synthetic precursor. The samples were characterized by X-ray diffraction（XRD）. Their crystal phases show an olivine structure. Only the sample obtained at 700℃ has a larger discharge capacity, which has good electrochemical properties： its discharge specific capacity is 120. 3 mAh/g at a current of 0. 05 mA, and its capacity fade is very low after 20 cycles. It is demonstrated that the best synthetic temperature should be 700℃.

Characterization and Electrochemical Performance of ZnO Modified LiFePO_4/C Cathode Materials for Lithium-ion Batteries

To improve the electrical conductivity of LiFePO4 cathode materials, the ZnO modified LiFePO4/C cathode materials are synthesized by a two-step process including solid state synthesis method and precipitation method. The structures and compositions of ZnO modified LiFePO4/C cathode materials are characterized and analyzed by X-ray diffraction, scanning electron microscopy, transmission electron microscopy and energy dispersive spectroscopy, which indicates that the existence of ZnOhas little or no effect on the crystal structure, particles size and morphology of LiFePO4. The electrochemical performances are also characterized and analyzed with charge-discharge test, cyclic voltammetry and electrochemical impedance spectroscopy. The results show that the existence of ZnO improves the specific capability and lithium ion diffusion rate of LiFePO4 cathode materials and reduces the charge transfer resistance of cell, and the one with 3 wt% ZnO exhibits the best electrochemical performance.

Analysis of the factors affecting rate performance of LiFePO_4 lithium-ion batteries

In this paper,a water-based binder was used in LiFePO4 Li-ion batteries and the factors affecting the battery performance were analyzed. The type and amount of conductive agent and the amount of binder were found to have a significant impact on the rate performance of LiFePO4 Li-ion batteries. The impact of the two types of binders used in the test was not obvious.

Li₂MnSiO₄/Carbon Composite Nanofibers as a High-Capacity Cathode Material for Li-Ion Batteries

Li2MnSiO4 has an extremely high theoretical capacity of 332 mAh?g?1. However, only around half of this capacity has been realized in practice and the capacity retention during cycling is also low. In this study, Li2MnSiO4/carbon composite nanofibers were prepared by a combination of electrospinning and heat treatment. The one-dimensional continuous carbon nanofiber matrix serves as long-distance conductive pathways for both electrons and ions. The composite nanofiber structure avoids the aggregation of Li2MnSiO4 particles, which in turn enhances the electrode conductivity and promotes the reaction kinetics. The resultant Li2MnSiO4/carbon composite nanofibers were used as the cathode material for Li-ion batteries, and they delivered high charge and discharge capacities of 218 and 185 mAh?g?1, respectively, at the second cycle. In addition, the capacity retention of Li2MnSiO4 at the first 20th cycles increased from 37% to 54% in composite nanofibers.

Fabrication and Characterization of LiFePO4 Nanotubes by a Sol-gel-AAO Template Process

The LiFePO4 nanotubes were successfully fabricated by a sol-gel method with porous anodic aluminum oxide as the template. Transmission electron microscopy and scanning electron microscopy showed that the synthesized LiFeP04 nanotubes were monodispersed and parallel to one another. Selected area electron diffraction pattern, X-ray diffraction and X-ray photoelectron spectroscopy investigations jointly demonstrated that the synthesized LiFePO4 nanotubes were pure olivine structure. This approach offered a potentially way for fabricating ordered LiFePO4 nanotubes at room temperature and ambient conditions, which might be expected to find promising application as a new cathode material in lithium ion battery,

Preparation and electrochemical performance of 2LiFe_(1-x)Co_xPO_4-Li_3V_2(PO_4)_3/C cathode material for lithium-ion batteries

2LiFe1-xCoxPO4-Li3V2（P04）3/C was synthesized using Fel-2xCo2xVO4 as precursor which was prepared by a simple co-precipitation method. 2LiFej-xCoxPO4-Li3V2（PO4）3/C samples were characterized by X-ray diffraction （XRD）, scanning electron microscopy （SEM） and electrochemical measurements. All 2LiFel-xCoxPOa-Li3V2（PO4）3/C composites are of the similar crystal structure. The XRD analysis and SEM images show that 2LiFe0.96Co0.04PO4-Li3V2（PO4）3/C sample has the best-ordered structure and the smallest particle size. The charge-discharge tests demonstrate that these powders have the best electrochemical properties with an initial discharge capacity of 144.1 mA.h/g and capacity retention of 95.6% after 100 cycles when cycled at a current density of 0.1C between 2.5 and 4.5 V.