Highly selective extraction of aromatics from aliphatics by using metal chloride-based ionic liquids

The separation of aromatics from aliphatics is essential for achieving maximum exploitation of oil resources in the petrochemical industry.In this study,a series of metal chloride-based ionic liquids were prepared and their performances in the separation of 1,2,3,4-tetrahydronaphthalene(tetralin)/dodecane and tetralin/decalin systems were studied.Among these ionic liquids,1-ethyl-3-methylimidazolium tetrachloroferrate([EMIM][FeCl_(4)])with the highest selectivity was used as the extractant.Density functional theory calculations showed that[EMIM][FeCl_(4)]interacted more strongly with tetralin than with dodecane and decalin.Energy decomposition analysis of[EMIM][FeCl_(4)]-tetralin indicated that electrostatics and dispersion played essential roles,and induction cannot be neglected.The van der Waals forces was a main effect in[EMIM][FeCl_(4)]-tetralin by independent gradient model analysis.The tetralin distribution coefficient and selectivity were 0.8 and 110,respectively,with 10%(mol)tetralin in the initial tetralin/dodecane system,and 0.67 and 19.5,respectively,with 10%(mol)tetralin in the initial tetralin/decalin system.The selectivity increased with decreasing alkyl chain length of the extractant.The influence of the extraction temperature,extractant dosage,and initial concentrations of the system components on the separation performance were studied.Recycling experiments showed that the regenerated[EMIM][FeCl_(4)]could be used repeatedly.

Efficient and selective extraction of uranium from seawater based on a novel pulsed liquid chromatography radionuclide separation method

The novel pulsed liquid chromatography radionuclide separation method presented here provides a new and promising strategy for the extraction of uranium from seawater.In this study,a new chromatographic separation method was proposed,and a pulsed nuclide automated separation device was developed,alongside a new chromatographic column.The length of this chromatographic column was 10 m,with an internal warp of 3 mm and a packing size of 1 mm,while the total separation units of the column reached 12,250.The most favorable conditions for the separation of nuclides were then obtained through optimizing the separation conditions of the device:Sample pH in the column=2,sample injection flow rate=5.698 mL/min,chromatographic column heating temperature=60℃.Separation experiments were also carried out for uranium,europium,and sodium ions in mixed solutions;uranium and sodium ions in water samples from the Ganjiang River;and uranium,sodium,and magnesium ions from seawater samples.The separation factors between the different nuclei were then calculated based on the experimental data,and a formula for the separation level was derived.The experimental results showed that the separation factor in the mixed solution of uranium and europium(1:1)was 1.088,while achieving the initial separation of uranium and europium theoretically required a 47-stage separation.Considering the separation factor of 1.50for the uranium and sodium ions in water samples from the Ganjiang River,achieving the initial separation of uranium and sodium ions would have theoretically required at least a 21-stage separation.Furthermore,for the seawater sample separation experiments,the separation factor of uranium and sodium ions was 1.2885;therefore,more than 28 stages of sample separation would be required to achieve uranium extraction from seawater.The novel pulsed liquid chromatography method proposed in this study was innovative in terms of uranium separation and enrichment,while expanding the possibilities of extracting uranium from seawater through chromatography.

COSMO-RS prediction and experimental verification of 1,5-pentanediamine extraction from aqueous solution by ionic liquids

1,5-Pentanediamine(PDA)produced by biological fermentation becomes popular,but the separation of PDA from the broth is a typical difficult problem.In this work,the performance of 200 ionic liquids(ILs),formed by combining 25 cations and 8 anions,in the extraction of PDA from aqueous solution were evaluated using COSMO-RS model.The extraction mechanism was investigated with the help ofσ-profile and interaction energy analyses.Both the cation and anion have impacts on the extraction efficiency,where cation mainly influences the interaction of IL with PDA and anion affects the hydrophobicity of IL.The IL composed of long alkyl-chain in cation and the anion of[PF6]-or[TF2 N]-,which has theσ-profile more likely distributed in the nonpolar region but less distributed in the polar region,is favorable for extraction.The experimental liquid-liquid equilibrium demonstrated the effects of cation and anion on extraction performance,which validated the reliability of COSMO-RS model in IL screening for PDA extraction.The IL[IM-1,8][PF6]could serve as a promising extractant for the downstream separation process of the biological production of PDA.

Extraction Kinetics of Lanthanum in Chloride Medium by Bifunctional Ionic Liquid [A336][CA-12] Using a Constant Interfacial Cell with Laminar Flow

The extraction kinetics of La(III) from aqueous chloride solutions into n-heptane solutions of bifunctional ionic liquid extractant [A336][CA-12](tricaprylmethylammonium sec-octylphenoxy acetic acid) was investigated using a constant interfacial cell with laminar flow. The effects of stirring speed, temperature and specific interfacial area on the extraction rate were examined. The results indicate that mass transfer kinetics of La(III) is a mixed-controlled process influenced by interfacial reaction. On the basis of mass transfer kinetic results in the extraction of La(III) by [A336][CA-12], the extraction rate equation of La(III) is proposed in terms of pseudo-firstorder constants, which is supported by the measured thermodynamic equations. The mass-transfer kinetic model deduced from the rate controlling step is adequate to interpret the experimental data qualitatively.

Extraction of Theanine from Waste Liquid of Tea Polyphenol Production in Aqueous Two-phase Systems with Cationic and Anionic Surfactants

Extraction of theanine from waste liquid of tea polyphenol production was studied in aqueous surfactanttwo-phase system （ASTP） with cationic surfactant （CTAB） and anionic surfactant （SDS）. Results indicate that the region of ASTP is narrow and there is only a two-phase region of cationic surfactant. The increase in concentrations of NaBr and Na2SO4 are beneficial to the formation of ASTP. Theanine concentration in the bottom phase increases with increasing concentration of theanine, whereas the Partition coefficient and extraction rate only change a littlewhen the concentration of theanine is above 0.2 g.L-＇. With the increase of SDS concentration, the phase ratio and the partition coefficient decrease, while the extraction efficiency of theanine increases and the concentration of theanine changes a little in the range from 2.4/7.5 to 2.8/7.2 for SDS/CTAB ratio. The temperature has a notable ef- fect on the concentration of theanine in the bottom phase, partition coefficient and extraction rate of theanine. The increase of waste liquid decreases the phase ratio, increases the concentration and extraction rate of theanine in the bottom ohase, since the orotein and the saccharide enter the bottom nhase with theanine.

Ionic Liquid-salt Aqueous Two-phase System, a Novel System for theExtraction of Abused Drugs

A 1-butyl-3-methylimidazolium chloride-salt aqueous two-phase system was studied on extraction of abused drugs. The effects of sorts of salts, temperature, concentration of salt and drugs on system were investigated systematically. A satisfactory extraction efficiency of 93% was obtained for papaverine while that of morphine was 65%. The extraction mechanism was primarily discussed.

Separation of tungsten and molybdenum with solvent extraction using functionalized ionic liquid tricaprylmethylammonium bis(2,4,4-trimethylpentyl)phosphinate

Functionalized ionic liquids(FILs)as extractants were employed for the separation of tungsten and molybdenum from a sulfate solution for the first time.The effects of initial pH,extractant concentration,metal concentrations in the feed were comprehensively investigated.The results showed that tricaprylmethylammonium bis(2,4,4-trimethylpentyl)phosphinate([A336][Cyanex272])could selectively extract W over Mo at an initial pH value of 5.5;the best separation factorβ_(W/Mo) of 25.61 was obtained for a solution with low metal concentrations(WO3:2.49 g/L,Mo:1.04 g/L).The[A336][Cyanex272]system performed effectively for solutions of different W/Mo molar ratios and different metal ion concentrations in the feed.The chemical reaction between[A336][Cyanex272]and W followed the ion association mechanism,which was further proved by the Fourier-transform infrared(FTIR)spectra of loaded[A336][Cyanex272]and the free extractant.The stripping experiments indicated that 95.48%W and 100.00%Mo were stripped using a 0.20 mol/L sodium hydroxide solution.Finally,the selective extractions of W and Mo from two synthetic solutions of different high metal concentrations were obtained;the separation factorβW/Mo reached 23.24 and 17.59 for the first and second solutions,respectively.The results suggest the feasibility of[A336][Cyanex272]as an extractant for the separation of tungsten and molybdenum.

Hollow fiber-based liquid phase microextraction followed by analytical instrumental techniques for quantitative analysis of heavy metal ions and pharmaceuticals

Hollow-fiber liquid-phase microextraction(HF-LPME)and electromembrane extraction(EME)are miniaturized extraction techniques,and have been coupled with various analytical instruments for trace analysis of heavy metals,drugs and other organic compounds,in recent years.HF-LPME and EME provide high selectivity,efficient sample cleanup and enrichment,and reduce the consumption of organic sol-vents to a few micro-liters per sample.HF-LPME and EME are compatible with different analytical in-struments for chromatography,electrophoresis,atomic spectroscopy,mass spectrometry,and electrochemical detection.HF-LPME and EME have gained significant popularity during the recent years.This review focuses on hollow fiber based techniques(especially HF-LPME and EME)of heavy metals and pharmaceuticals(published 2017 to May 2019),and their combinations with atomic spectroscopy,UV-VIS spectrophotometry,high performance liquid chromatography,gas chromatography,capillary elec-trophoresis,and voltammetry.

A highly sensitive SPE-liquid/liquid extraction-RPLC analytical method for the determination of 6β-hydroxycortisol and cortisol in cancer patients' urine

A highly sensitive SPE-liquid/liquid extraction RPLC method has been developed for the analysis of 6β-hydroxycortisol and cortisol in the urine of cancer patients. Methods： After SPE column purification and liquid-liquid extraction, the sample test solutions were analyzed with RPLC using a C18 analytical column. This improved analytical method has been validated for linearity, accuracy （recovery from urine）, repeatability （within-day and between-day precision）, specificity, sensitivity, and stability. This SPE-liquid/liquid extraction-RPLC is rapid, simple, accurate and reproducible. The technique is particularly useful for monitoring the CYP3A activity of cancer patients in clinical settings. The results are expressed as the ratio of 6β-hydroxycortisol to cortisol. Results： The CYP3A activity from a total of 153 samples was measured using this improved method. Considerable variation in the CYP3A activity of different cancer patients has been documented. Thus, personalized medical treatment based on the individual metabolic enzyme activity level is necessary. Conclusion： This new analytical method facilitates such individualized medical treatments.

Improved determination of salicylaldoxime in water samples by liquid-liquid extraction followed by high performance liquid chromatographic analysis

For the determination of salicylaldoxime in environmental water samples,a stable and rapid method with low detection was proposed and established,based on the liquid-liquid extraction-high performance liquid chromatography with ultraviolet detector.Parameters including extraction solvent,ionic strength,solution pH,and extraction pattern were discussed for the optimal quantification of salicylaldoxime-spiked water.When the described method was applied to four spiked water samples,the obtained average extraction recovery rate was found between 87%–107%and relative standard deviation was below 6%.At the same time,good linear relationships were observed for spiked water samples from 0.01 to 10μg/mL(R2=0.9993).In addition,the detection limit of salicylaldoxime was revealed between 0.003–0.008μg/mL,which is two orders of magnitude lower than previously reported results.Thus,the presented method may be advantageous for the high-efficiency determination of salicylaldoxime in water samples.

Rapid analysis of fifteen sulfonamide residues in pork and fish samples by automated on-line solid phase extraction coupled to liquid chromatography–tandem mass spectrometry

The aim of this work was to develop an automated on-line solid phase extraction(SPE)with liquid chromatography-tandem mass spectrometry method for the detection of fifteen sulfonamides in pork and fish samples.Samples were extracted with 0.2%formic acid acetonitrile solution,purified by on-line SPE device with HLB column,then separated by XBridge C18 column,using 0.1%formic acid solution and acetonitrile as the mobile phase.Mass spectrometric data was acquired under multiple reaction monitoring(MRM)mode using positive ionization electrospray.Internal standard method was used in the quantification,good linear relationship was got in range of 0.1–100 ng/mL and correlation coefficient was higher than 0.9990.The limits of detection were in the range of 0.125–2.00g/kg and the limits of quantitation were in the range of 0.250–5.00g/kg.Recoveries of the method were in range of 78.3%–99.3%,relative standard deviation were lower than 10%.The method was simple,sensitivity,and could be used for routine supervision and analysis of fifteen sulfonamides in pork and fish.

Dynamic microwave-assisted extraction combined with liquid phase microextraction based on the solidification of a floating drop for the analysis of organochlorine pesticides in grains followed by GC

A convenient,cost-effective and fast method using dynamic microwave-assisted extraction and liquid phase microextraction based on the solidification of a floating drop was proposed to analyze organochlorine pesticides in grains including rice,maize and millet.Twelve samples can be processed simultaneously in the method.During the extraction process,10%acetonitrile-water solutions containing 110μL of n-hexadecane were used to extract organochlorine pesticides.Subsequently,1.0 g sodium chloride was placed in the extract,and then centrifuged and cooled.The n-hexadecane drops containing the analytes were solidifi ed and transferred for determination by gas chromatography-electron capture detector without any further filtration or cleaning process.Limits of detection for organochlorine pesticides were 0.97–1.01μg/kg and the RSDs were in the range of 2.6%–8.5%.The developed technology has succeeded in analyzing six real grains samples and the recoveries of the organochlorine pesticides were 72.2%–94.3%.Compared with the published extraction methods,the developed method was used to analyze organochlorine pesticides in grains,being more environmentally friendly,which is suitable for the daily determination of organochlorine pesticides.

Gas-liquid-liquid extraction in a novel rotating microchannel extractor

In this work,a novel rotating microchannel extractor(RME)is designed and further used for the extraction of chromium(Ⅲ)from water.Unexpectedly,the micro-extraction had the same effect as carrying out 2.9-stage cross-flow extractions.Various factors,including the gas intake methods,gas intake quantity(Qg),distance between inner rotor and outer wall(D),rotational inner rotor speed(R)and volumetric flow rate(Qa,Qo),were selected to investigate their effect on the extraction efficiency(η)thoroughly.The relation map ofηwith Weaand We(o-g)for RME provides a comprehension for the gas–liquid–liquid extraction process in this RME system.

Solvent Extraction of Yttrium by Task-specific Ionic Liquids Bearing Carboxylic Group

A new kind of hydrophobic ionic liquids [1-alkyl-3-（1-carboxylpropyl）im][PF6] has been synthesized, and their extraction.properties for Y（III） in the nitric acid medium was also investigated. The effects of extractant concentration, equilibrium pH of aqueous phase, salt concentration, temperature etc. were discussed. The results show that this kind of Task-Specific Ionic Liquid （TSIL） needs to be saponified before being used for the Y（III） extraction, and the extraction is-acid dependent,-and the extraction efficiency increases with the aqueous phase acldity decreasing. Furthermore, the loaded organic phase is easy to be stripped; more than 95% Y（III） could be stripped from the loaded organic phase when the stripping acidity is higher than 0.07 mol-L-1. The slope analysis technique is used to investigate the extraction mechanism, and a possible cation-exchange extraction mechanism is proposed in the oresent extraction system.

Determination of Sulfadimidine in Royal Jelly by C_(18)-functionalized Magnetic Silica Nanoparticles Solid Phase Extraction-High Performance Liquid Chromatography-Tandem Mass Spectrometry

[Objective] This study aimed to develop a method of C_18-functionalized magnetic silica nanoparticles solid phase extraction-high performance liquid chro- matography-tandem mass spectrometry for the determination of sulfadimidine in royal jelly. [Method] The royal jelly samples were pretreated by MCX SPE column and C_18-functionalized magnetic silica nanoparticles, and the purified samples were de- tected by HPLC-MS/MS. [Result] The detection method showed a good linear rela- tionship in the range of 5-80 ugkg （r=0.993 1）. The recovery ranges were between 93%- 104% with the relative standard deviations （RSD） below 11.3%. [Conclusion] Combined with automation equipment, the method is simple, fast, time-saving, and easy to real- ize the automation of sulfadimidine in the royal jelly samples before determination.

Salting-Out Assisted Liquid-Liquid Extraction Combined with HPLC for Quantitative Extraction of Trace Multiclass Pesticide Residues from Environmental Waters

In this study, salting-out assisted liquid-liquid extraction combined with high performance liquid chromatography diode array detector (SALLE-HPLC-DAD) method was developed and validated for simultaneous analysis of carbaryl, atrazine, propazine, chlorothalonil, dimethametryn and terbutryn in environmental water samples. Parameters affecting the extraction efficiency such as type and volume of extraction solvent, sample volume, salt type and amount, centrifugation speed and time, and sample pH were optimized. Under the optimum extraction conditions the method was linear over the range of 10 - 100 μg/L (carbaryl), 8 - 100 μg/L (atarzine), 7 - 100 μg/L (propazine) and 9 - 100 μg/L (chlorothalonil, terbutryn and dimethametryn) with correlation coefficients (R2) between 0.99 and 0.999. Limits of detection and quantification ranged from 2.0 to 2.8 μg/L and 6.7 to 9.5 μg/L, respectively. The extraction recoveries obtained for ground, lake and river waters were in a range of 75.5% to 106.6%, with the intra-day and inter-day relative standard deviation lower than 3.4% for all the target analytes. All of the target analytes were not detected in these samples. Therefore, the proposed SALLE-HPLC-DAD method is simple, rapid, cheap and environmentally friendly for the determination of the aforementioned herbicides, insecticide and fungicide residues in environmental water samples.

Simultaneous Determination of Bisphenols and Alkylphenols in Water by Solid Phase Extraction and Ultra Performance Liquid Chromatography-tandem Mass Spectrometry

To establish an analytical method for determination of four bisphenols （BPA, BPB, BPF, and BPS） and two alkylphenols （4-n-OP, 4-n-NP） in water by ultra performance liquid chromatography- tandem mass spectrometry （UPLC/MS/MS）. The water samples were extracted and condensed with solid-phase extraction （SPE） using C18 cartridges and eluted by acetonitrile. Separation was carried out with Acquity BEH C8 column and detection were performed by UPLC/MS/MS. Quantification was calculated by using the internal standard BPA-d16 and 4-n-NP-d8. The linear correlation coefficients of these compounds in the range of 1.0-100.0μg/L were all over 0.999. The minimum detectable concentrations were 0.75-1.0 ng/L, and the recoveries ranged from 87.0% to 106.9%.

High-efficiency Extraction of Bitumen from Oil Sands Using Mixture of Ionic Liquid [Emim][BF_(4)] and Dichloromethane

An ionic liquid(IL),1-ethyl-3-methyl imidazolium tetrafluoroborate([Emim][BF_(4)]),was used to enhance bitumen recovery from oil sands by dichloromethane solvent extraction.A multiphase system could be formed by simply mixing the components at ambient temperature,consisting of sands and clays,mixtures of ionic liquid and dichloromethane,and concentrated bitumen layer.The results demonstrated that[Emim][BF_(4)]increased the bitumen recovery up to 92%.Much less clay fines were found in the recovered bitumen than those formed by using dichloromethane solvent extraction alone,and the dichloromethane residue was not detected in the spent sands.We proposed that[Emim][BF_(4)]had an ability to reduce the adhesion of bitumen to sand,resulting in an improved separation efficiency.Furthermore,[Emim][BF_(4)]could facilitate the transfer of the extracted bitumen to the surface interface,and then the bitumen was auto-partitioned to a separate immiscible phase for ease of harvesting.This technology circumvented the issue of high consumption of distillation energy due to separation of bitumen phase and low boiling point of dichloromethane.[Emim][BF_(4)]and dichloromethane could be readily recycled through the system and used repeatedly.After ten cycles,the bitumen recovery remained above 88%.Initial scale-up work suggested that this approach would form the basis for a viable large-scale process.

Synthesis of 2, 6 Bis(1′-Phenyl- 3′- Methyl-5′-Oxopyrazole- 4′) Pyridinediacyl and Its Solid Liquid Extraction Behavior for Ce(Ⅲ)

diketone type chelating ligands have high coordinative activity and selectivity, and are widely applied in analytical chemistry. In order to obtain profounder understanding to the properties of bis(4 acylpyrazolone 5), A new 4 acylpyrazol 5 one derivative (H 2BPMPP) was syntheszed, which contains a heterocyclic ring between two 1 phenyl 3 methyl 4 acylpyrazol 5 one rings. The new compound was characterized by element analyses, UV, IR and 1H NMR spectra. The equilibrium of the keto enol tautomerism was studied. The results show that a lower dielectric constant of solvent favors the enol form which has a higher λ max . Due to special merits of paraffin wax, the solid liquid extraction behavior of Ce(Ⅲ) with molten paraffin wax as a diluent was also investigated at higher temperature. The value of the pH 1/2 was 3.19 and the value of log K ex was 3.467. The chemical composition of the complex was obtained by the slope analysis method.

Use of Ionic Liquid-filled Semipermeable Membrane for Extraction of Polycyclic Aromatic Hydrocarbons in Water

A novel and facile sample preparation method was developed for the extraction of polycyclic aromatic hydrocarbons (PAHs) in aqueous sample solution using 1-butyl-3- methylimidazolium hexafluorophosphate ([C4MIM][PF6]) – filled semipermeable membrane. For 24 hrs extraction of naphthalene, 1-methylnaphthalene, 2-chloronaphthalene, phenanthrene, the result showed that the extraction efficiency, correlation coefficient (R2) and RSD (n=5) were in the range of 67-102 %, 0.9870-0.9962, and 2.1-5.3 %, respectively.