Reduction Discoloration of Reactive Dyed Cotton Waste and Chemical Recycling via Ionic Liquid

The textile industry generates large volumes of waste throughout its production process.Most of this waste is colored,therefore,discoloration is an important step toward recycling and reusing this waste.This study focused on the chemical reductive discoloration of textile waste composed of cotton dyed with reactive dye.The experimental design demonstrated the significant influence of the concentration of reducing agent and time of reaction on the degree of whiteness of the cotton fibers.The concentration of the alkaline agent was not significant in the process.The optimization of the reaction conditions lead to Berger degree of 50.5±3.5.The discolored cotton was chemically recycled through dissolution in ionic liquid 1-ethyl-3-methylimidazolium chloride and regeneration in film form in water.The microstructure of the regenerated cellulose films was evaluated by Scanning Electron Microscopy(SEM)indicating complete dissolution and uniform regeneration.The discoloration process reduced the polymerization degree and crystallinity index of the cotton fibers but retained the cellulose I structure.The dissolution and cellulose regeneration process results in transparent films with an amorphous structure.The thermal behavior,evaluated by thermogravimetric analysis,indicated that residues and regenerated film presented a main decomposition step.The maximum decomposition rate temperature of the regenerated films was approximately 40℃lower than the cotton fibers,which correlates well with the reduction in polymerization degree and amorphous structure.In general,the study demonstrated that textile cotton waste dyed with reactive dyes can be chemically discolored to form transparent and amorphous films,contributing to the development of sustainable strategies for the textile industry.

Application of Waste Liquids Containing Lignin from Pulp-producing Industry to CWM Preparation

Three kinds of craft waste liquids, which are by-products in the pulp industry and contain much lignin, were used as dispersing additives for preparing Horonai coal CWM(coal water mixture). The experiments showed that the CWM exhibited the lowest viscosity when it was diluted with an appropriate amount of water with the waste eiquids added. The experiments also indicated that the maximum coal concentration in the practically applicable CWMs whose apparent viscosity has to be below 1000 mPa·s increased from 56.5% to 62.5%(mass fraction), and 56.5% is the maximum coal mass fraction of the CWM prepared without additives. These data show the effectiveness of the waste liquids as the additives for preparing CWMs. The zeta potential of coal particles in the CWMs changed with the addition of lignin. From the change, the steric repulsion effect of the lignin adsorbed on the coal particles is concluded to be mainly responsible for the CWM dispersion. The waste liquids contain less sulfur than PSSNa(polystyrene sulfonate sodium salt), a typical dispersant which is currently used for preparing the commercial CWM, when the sulfur content in the unit mass of the solid matters within the waste liquids is compared with that in unit mass of PSSNa. This fact suggests that the waste liquids are more advantageous than PSSNa as far as air pollutants are concerned.

Effect of preparation methods on the adsorption property of municipal solid waste-based carbon materials

Three different preparation methods including steam physical activation, catalytic carbonation and KOH chemical activation methods were used to prepare municipal solid waste- based carbon materials. The methylene blue （MB） adsorption value was applied to evaluate the adsorption capabilities of the prepared carbon materials. The effects of preparation methods on adsorption capability and yield of products were investigated. The yield of carbon materials with the catalytic carbonation method is the highest, and the KOH activation method is the second level. Considering the adsorption performance, the KOH activation method is much more favorable. Among the different components of municipal solid waste-based carbon materials, the adsorption properties of the single component of paperboard, the double components of tire and paperboard, the triple components of tire, paperboard and polyvinyl chloride （PVC）, and the multi-component mixtures are better than those of other single-, double-, triple- and multi-component mixtures, respectively.

Recovery of heavy metals from electroplating sludge and stainless steel pickle waste liquid by ammonia leaching method

A coordinative disposal process for treatment of electroplating sludge and stainless steel pickle waste liquid containing Cu, Ni, Zn, Cr and Fe etc., has been developed to recover valuable metals and to eliminate pollution. The recovery of Cu, Ni, Zn and Cr is 94%, 91%, 90% and 95%, respectively. The ammonia was recycled by the simplified process of CaO caustic distillation. The precipitated product of Cu, Ni and Zn obtained from caustic distillation of ammonia was separated by extraction or high\|pressure hydrogen reduction in an autoclave. The qualified metal salt products were obtained through extraction. The rich chromium residue from coordinative disposal was subjected to recover Cr by hydrothermal oxidation in NaOH medium and Fe\-3O\-4 was synthesized by wet methods from the residue produced by extracting Cr. Cr was a stable chemical fixed in Fe\-3O\-4 and harmless. The recovery process has been used in a pilot plant with sludge production capacity of 2000 t/a.

Advancements in the preparation of high-performance liquid chromatographic organic polymer monoliths for the separation of small-molecule drugs

The various advantages of organic polymer monoliths, including relatively simple preparation processes,abundant monomer availability, and a wide application range of pH, have attracted the attention of chromatographers. Organic polymer monoliths prepared by traditional methods only have macropores and mesopores, and micropores of less than 50 nm are not commonly available. These typical monoliths are suitable for the separation of biological macromolecules such as proteins and nucleic acids, but their ability to separate small molecular compounds is poor. In recent years, researchers have successfully modified polymer monoliths to achieve uniform compact pore structures. In particular, microporous materials with pores of 50 nm or less that can provide a large enough surface area are the key to the separation of small molecules. In this review, preparation methods of polymer monoliths for high-performance liquid chromatography, including ultra-high cross-linking technology, post-surface modification, and the addition of nanomaterials, are discussed. Modified monolithic columns have been used successfully to separate small molecules with obvious improvements in column efficiency.

Waste Activated Sludge Alkaline Fermentation Liquid as Carbon Source for Biological Nutrients Removal in Anaerobic Followed by Alternating Aerobic-Anoxic Sequencing Batch Reactors

Activated sludge process has been widely used to remove phosphorus and nitrogen from wastewater. However,the nitrogen and phosphorus removal is sometimes unsatisfactory due to the low influent COD.Another problem with the activated sludge process is that large amount of waste activated sludge is produced,which needs further treatment.In this study,the waste activated sludge alkaline fermentation liquid was used as the main carbon source for phosphorus and nitrogen removal under anaerobic followed by alternating aerobic-anoxic conditions,and the results were compared with those using acetic acid as the carbon source.The use of alkaline fermentation liquid not only affected the transformations of phosphorus,nitrogen,intracellular polyhydroxyalkanoates and glycogen, but also led to higher removal efficiencies for phosphorus and nitrogen compared with acetic acid.It was observed that ammonium was completely removed with either alkaline fermentation liquid or acetic acid as the carbon source. However,the former resulted in higher removal efficiencies for phosphorus(95%)and nitrogen(82%),while the latter showed lower ones(87%and 74%,respectively).The presence of a large amount of propionic acid in the alkaline fermentation liquid was one possible reason for its higher phosphorus removal efficiency.Exogenous instead of endogenous denitrification was the main pathway for nitrogen removal with the alkaline fermentation liquid as the carbon source,which was responsible for its higher nitrogen removal efficiency.It seems that the alkaline fermentation liquid can replace acetic acid as the carbon source for phosphorus and nitrogen removal in anaerobic fol- lowed by alternating aerobic-anoxic sequencing batch reactor.

Preparation and characterization of amino or carboxyl-functionalized ionic liquids

New functionalized ionic liquids, 1-carboxylmethyl-3-methylimimidazolium hexafluorophosphate or fluoborate and 1-aminoethyl-3-methylimimidazolium hexafluorophosphate or fluoborate have been synthesized and investigated. The obtained amino or carboxyl-functionalized ionic liquids were all characterized by FT-IR, ^1H NMR and MS （ESI） and their properties such as freezing point, viscosity, solubility, specific gravity, surface tension, and interfacial tension were also determined.

Crystalline Silicotitanate: a New Type of Ion Exchanger for Cs Removal from Liquid Waste

The research and developments of a new type of inorganic ion exchanger, crystalline silicotitanate (CST) are reviewed. This material is stable against radiation, and the CST has high selectivity for Cs over Na, K and Rb. It performs well in acidic, neutral, and basic solutions. The results of ion exchange tests show that CST is an excellent candidate for Cs removal from high-level liquid waste.

Preparation and Characterization of New Type Ionic Liquids

A new type of ionic liquids containing cation of diacetone acrylamide [or N-(1,1- bismethyl-3-oxo-butyl)acrylamide] and anions such as CH3COO- (Ac), CF3COO- (TF), BF4-(BF), PF6-(PF), HSO4-(SO) and Cl-(Cl) were prepared by normal neutralization. The obtained ionic liquids were identified by FT-IR and 1H NMR spectroscopy. However, their properties such as melting point, conductivity, viscosity etc. were determined.

HPLC Fingerprint with Multi-components Analysis for Quality Consistency Evaluation of Traditional Chinese Medicine Si-Mo-Tang Oral Liquid Preparation

Si-Mo-Tang（SMT） oral liquid preparation, a traditional Chinese medicine, was prepared from four crude herbal drugs, Fructus Aurantii Submaturus, Radix Aucklandiae, Semen Arecae and Radix Linderae Aggregatae. A combinative method using HPLC fingerprint and quantitative analysis was developed and validated for quality consistency evaluation of SMT. Individual HPLC chromatograms were evaluated against the mean chromatogram generated via a similarity evaluation computer program. Data from chromatographic fingerprints were also processed with principal component analysis（PCA） and hierarchical cluster analysis（HCA）. Additionally, six components （naringin, isonaringin, hesperidin, neohesperidin, norisoboldine and potassium sorbate） in SMT were simultaneously determined to interpret the quality consistency. For fingerprint analysis, 20 peaks were selected as the characteristic peaks to evaluate the similarities of 26 SMT collected from different manufacturers. Among the 20 characteristic peaks, 10 peaks were assigned to be naringin, hesperidin, neohesperidin, isonaringin, neoeriocitrin, tangeretin, nobiletin, norisoboldine, 5-（ethoxymethyl）furan-2-carbaldehyde and potassium sorbate, respectively. The results of similarity analysis, PCA and HCA, indicate that the samples from different manufacturers were consistent with each other in composition. The results from the quantitative data show that the contents of six compounds were significantly different in SMT oral liquid preparations from different manufacturers. The combinative method of chromatographic fingerprint with quantitative analysis developed here offered an efficient way for the quality consistency evaluation of the traditional Chinese medicine SMT.

Extraction of Theanine from Waste Liquid of Tea Polyphenol Production in Aqueous Two-phase Systems with Cationic and Anionic Surfactants

Extraction of theanine from waste liquid of tea polyphenol production was studied in aqueous surfactanttwo-phase system （ASTP） with cationic surfactant （CTAB） and anionic surfactant （SDS）. Results indicate that the region of ASTP is narrow and there is only a two-phase region of cationic surfactant. The increase in concentrations of NaBr and Na2SO4 are beneficial to the formation of ASTP. Theanine concentration in the bottom phase increases with increasing concentration of theanine, whereas the Partition coefficient and extraction rate only change a littlewhen the concentration of theanine is above 0.2 g.L-＇. With the increase of SDS concentration, the phase ratio and the partition coefficient decrease, while the extraction efficiency of theanine increases and the concentration of theanine changes a little in the range from 2.4/7.5 to 2.8/7.2 for SDS/CTAB ratio. The temperature has a notable ef- fect on the concentration of theanine in the bottom phase, partition coefficient and extraction rate of theanine. The increase of waste liquid decreases the phase ratio, increases the concentration and extraction rate of theanine in the bottom ohase, since the orotein and the saccharide enter the bottom nhase with theanine.

Quantification of six bioactive compounds in Zhenqi Fuzheng preparation by high-performance liquid chromatography coupled with diode array detector and evaporative light scattering detector

A simple and accurate high-performance liquid chromatography（HPLC）coupled with diode array detector（DAD）and evaporative light scattering detector（ELSD）was established for the determination of six bioactive compounds in Zhenqi Fuzheng preparation（ZFP）.The monitoring wavelengths were 254,275 and 328 nm.Under the optimum conditions,good separation was achieved,and the assay was fully validated in respect of precision,repeatability and accuracy.The proposed method was successfully applied to quantify the six ingredients in 31 batches of ZFP samples and evaluate the variation by hierarchical cluster analysis（HCA）,which demonstrated significant variations on the content of these compounds in the samples from different manufacturers with different preparation procedures.The developed HPLC method can be used as a valid analytical method to evaluate the intrinsic quality of this preparation.

A power plant for integrated waste energy recovery from liquid air energy storage and liquefied natural gas

Liquefied natural gas(LNG)is regarded as one of the cleanest fossil fuel and has experienced significant developments in recent years.The liquefaction process of natural gas is energy-intensive,while the regasification of LNG gives out a huge amount of waste energy since plenty of high grade cold energy(-160℃)from LNG is released to sea water directly in most cases,and also sometimes LNG is burned for regasification.On the other hand,liquid air energy storage(LAES)is an emerging energy storage technology for applications such as peak load shifting of power grids,which generates 30%-40%of compression heat(-200℃).Such heat could lead to energy waste if not recovered and used.The recovery of the compression heat is technically feasible but requires additional capital investment,which may not always be economically attractive.Therefore,we propose a power plant for recovering the waste cryogenic energy from LNG regasification and compression heat from the LAES.The challenge for such a power plant is the wide working temperature range between the low-temperature exergy source(-160℃)and heat source(-200℃).Nitrogen and argon are proposed as the working fluids to address the challenge.Thermodynamic analyses are carried out and the results show that the power plant could achieve a thermal efficiency of 27%and 19%and an exergy efficiency of 40%and 28%for nitrogen and argon,respectively.Here,with the nitrogen as working fluid undergoes a complete Brayton Cycle,while the argon based power plant goes through a combined Brayton and Rankine Cycle.Besides,the economic analysis shows that the payback period of this proposed system is only 2.2 years,utilizing the excess heat from a 5 MW/40 MWh LAES system.The findings suggest that the waste energy based power plant could be co-located with the LNG terminal and LAES plant,providing additional power output and reducing energy waste.

Chemical constituents and antioxidant activities of waste liquid extract from Apostichopus japonicus Selenka processing

Apostichopus japonicus Selenka is an ideal tonic food that is used traditionally in many Asian countries, and it contains many bioactive substances, such as antioxidant, antimicrobial, and anticancer materials. To convert waste liquid generated during production into a useful resource, extract from waste liquid was isolated by column chromatography and studied by the pyrogallol autoxidation and 1,10-phenanthroline-Fe^2＋ oxidation methods. Results show that the extract scavenged about 91% of the superoxide anion radical at a concentration of 1.4 mg/mL and 24% of the hydroxyl radical at 3.3 mg/mL. Four compounds were isolated and identified from the extract： 2,4-dihydroxy-5-methyl-1,3-azine; 2,4-dihydroxy- 1,3-diazine; 3-O-β-D-quinovopranosyl-（1→2）-4-O-sodium sulfate-β-D-xylopranosyl]-holosta-9（11）-ene313,12β,17α-triol; and 24-ethyl-5α-cholesta-7-ene-3β-O-β-D-xylopyranoside. All of these compounds are known in A. japonicus, and were found in the waste liquid for the first time.

Techniques for Treating Sulphuric Acid Pickling Waste Liquid of Steel Industry

Pickling waste liquid of the steel industry is included in National Hazardous Wastes Catalogue because of its high corrosion and large discharge. The techniques for treating pickling waste liquid （ H2SO4 ） in steel industry is summarized. The advantages, disadvantages and applied ranges of all kinds of control technologies are comparatively analysed. The research trends of techniques for treating pickling waste liquid （ H2SO4 ） are the resource reclamation technologies in future which is pointed out in the paper.

Acid Separation, Catalytic Oxidation and Coagulation for ATC Waste Liquid Treatment

It is difficult to treat 2-amino-thiazoline-4-carboxylic acid （ATC） waste liquid effectively at present for its characteristics of high chemical oxygen demand （COD）, high salinity and low biodegradability. In order to solve this problem, this paper presents several kinds of physical-chemical treatment unit techniques, including acid separation, catalytic oxidation and coagulation. First of all, acid separation was adopted to precipitate relevant organics at isoelectric point. When the temperature and pH value of acid separation were controlled at about 5 ℃ and 2.2 respectively, the COD removal rate could reach 27.600. Secondly, oxidation was used to break chemical constitution of refractory organics. The optimal reaction parameters of catalytic oxidation should be 20 ℃, pH adjusted to 5.0 and [Fe2+] 300 mg/L. Then with 500 H2O2 added and after one-hour reaction, the COD removal rate could achieve about 5200. Finally, coagulation was adopted to remove a portion of refractory organics, and 1500 polymeric molysite flocculant was the best for the coagulation, and the COD removal rate could reach about 1500. Therefore, the proposed feasible process of physical-chemical pretreatment for ATC waste liquid could have about 7000 COD removed in total.

Preparation of tetrapod-like ZnO whiskers from waste hot dipping zinc

Large and uniform tetrapod-like ZnO whiskers （T-ZnO） were prepared from waste hot dipping zinc by vapor oxidation and examined by means of X-ray diffraction and ICP-AES analysis and scanning electron microscope. The products are pure hexagonal wurtzite crystals with tetrapod shape and edge size of center body 56 μm and needle length of 100130 μm. The size and shape of ZnO particles are fully controlled by the growth conditions and T-ZnO can be obtained only at 8501 000 ℃ and total gas flow rate ranging from 40 to 250 L·h-1 in which the size of the T-ZnO particles varies slightly with temperature. The process of the formation of T-ZnO is that T-ZnO may nucleate at the initial stage with a complete tetrapod shape and develop to the large size, but not the process of （preferential） growth of octahedral nuclei and subsequent growth of the needles. The experiment presents a new method to prepare T-ZnO economically by using the waste hot dipping zinc.

Separation of ^(152+154)Eu,^(90)Sr from radioactive waste effluent using liquid–liquid extraction by polyglycerol phthalate

A new polyglycerol phthalate extractant was prepared and characterized using Fourier transform infrared spectroscopy, proton nuclear magnetic resonance(~1H NMR) spectroscopy, and thermogravimetric analysis. A preliminary study of the extraction of long-lived(^(90) Sr and ^(152+154)Eu) and short-lived(^(90) Y) radionuclides by polyglycerol phthalate was performed. The influence of different diluents, concentration of the acid, type of acid, and various interfering ions was explored. The stripping of ^(152+154)Eu radionuclide was studied by using different acid solutions, and it was found that sulfuric acid was the ideal acid for this purpose. Furthermore,^(152+154)Eu was extracted from the fission products(^(90) Sr) and the extraction% of^(90) Sr was found to improve in the presence of interfering ions.

Solid- liquid phase separation and resource recycling study for waste rolling oily sludge

On the basis of the characteristics of a highly emulsified solid-liquid phase （fine particles, sticky consistency,black color, and low reuse ratio）, waste rolling oily sludge has been a focal problem in the steel industry. In this article, a solid-liquid phase separation and resource recycling process was described, with pilot test results showing that flocculation-sedimentation is an effective pretreatment, and that the filtration-coagulationvacuum distillation process is simple and feasible with a 53.5% recovery rate for regenerated oil that is qualified for return to the roiling production line. Then,solid phase oil-sludge was extracted by solvents with a 77% metal resource recovery rate and a wide utilization range. Finally, according to the experimental results, a set of feasibility plans for a 50 t/a waste rolling oily sludge solid-liquid separation and resource recycle project was designed, with the expectation of 50% regenerated oil yield, 70% solid metal resource recovery, and a 2. 5-year investment payback period.

Studies on the structure and catalytic performance of Cu-Zn-Al catalyst prepared by liquid-phase preparation technology under different heat treatment atmosphere

Cu-Zn-Al slurry catalysts were prepared using a complete liquid-phase preparation technology under different heat treatment atmospheres.The catalysts were characterized using X-ray diffraction,X-ray photoelectron spectroscope,and N2 adsorption-desorption.Their application in the single-step synthesis of dimethyl ether from syngas was also investigated.The results indicate that the type of heat treatment atmosphere has an influence on the Cu species and the Cu0/Cu＋ ratio on the catalyst surface.Moreover,the final Cu/Zn ratio on the catalyst surface is mainly dependent on the composition and reaction environment of the catalyst and less on the type of heat treatment atmosphere.The prepared catalysts can suppress sintering of active sites at high temperatures,and the type of heat treatment atmosphere mainly affects the capability of the catalyst for methanol synthesis.The catalysts perform best using N2 as the heat treatment atmosphere.