Enhancing CO_(2) transport with plasma-functionalized ionic liquid membranes

The ionic liquid(IL) 1-butyl-3-methylimidazolium tetrafluoroborate treated with radiofrequency plasma is proposed for functionalization and immobilization on polyethersulfone supports to form supported ionic liquid membranes for CO_(2) separation.The effects of treatment time and transmembrane pressure difference on CO_(2) permeance were evaluated.The best gas permeation performance was obtained with a treatment time of 10 min and the transmembrane pressure difference was 0.25 MPa.Characterization of the materials by Fourier transform infrared spectroscopy,x-ray photoelectron spectroscopy and nuclear magnetic resonance spectroscopy demonstrates that the IL is grafted with carboxyl groups and deprotonated through plasma treatment.A preliminary mechanism for the plasma treatment and facilitated transport of CO_(2)has been proposed on this basis.

Di(2-ethylhexyl) phosphoric acid-coconut oil supported liquid membrane for the separation of copper ions from copper plating wastewater

Permeation of Cu（Ⅱ） from its aqueous solution through a supported liquid membrane （SLM） containing di（2-ethylhexyl）phosphoric acid （D2EHPA） carrier dissolved in coconut oil has been studied. The effects of Cu（Ⅱ）, pH （in feed）, H2SO4 （stripping） and D2EHPA （in membrane） concentrations have been investigated. The stability of the D2EHPA-coconut oil has also been evaluated. High Cu（Ⅱ） concentration in the feed leads to an increase in flux from 4.1 × 10^-9 to 8.9 × 10^-9 mol/（m^2·s） within the Cu（Ⅱ） concentration range 7.8×10^-4-78.6×10^-4 mol/L at pH of 4.0 in the feed and 12.4 × 10^-4 mol/L D2EHPA in the membrane phase. Increase in H2SO4 concentration in strip solution leads to an increase in copper ions flux up to 0.25 mol/L H2SO4, providing a maximum flux of 7.4 × 10^-9 mol/（m^2·s）. The optimum conditions for Cu（Ⅱ） transport are, pH of feed 4.0, 0.25 mol/L H2SO4 in strip phase and 12.4 × 10^-4 mol/L D2EHPA （membrane） in 0.5 μm pore size polytetrafluoroethylene （PTFE） membrane. It has been observed that Cu（Ⅱ） flux across the membrane tends to increase with the concentration of copper ions. Application of the method developed to copper plating bath rinse solutions has been found to be successful in the recovery of Cu（Ⅱ）.

Permeability and Selectivity of Sulfur Dioxide and Carbon Dioxide in Supported Ionic Liquid Membranes

Permeabilities and selectivities of gases such as carbon dioxide （CO2）, sulfur dioxide （SO2）, nitrogen （N2） and methane （CH4） in six imidazolium-based ionic liquids （[emim][BF4], [bmim][BF4], [bmim][PF6], [banim][BF4], [bmim][Tf2N] and [emim][CF3SO3]） supported on polyethersulfone microfiltration membranes are investigated in a single gas feed system using nitrogen as the environment and reference component at temperature from 25 to 45℃ and pressure of N2 from 100 to 400 kPa. It is found that SO2 has the highest permeability in the tested supported ionic liquid membranes, being an order of magnitude higher than that of CO2, and about 2 to 3 orders of magnitude larger than those of N2 and CH4. The observed selectivity of SO2 over the two ordinary gas components is also striking. It is shown experimentally that the dissolution and transport of gas components in the supported ionic liquid membranes, as well as the nature of ionic liquids play important roles in the gas permeation. A nonlinear increase of permeation rate with temperature and operation pressure is also observed for all sample gases. By considering the factors that influence the permeabilities and selectivities of CO2 and SO2, it is expected to develop an optimal supported ionic liquid membrane technology for the isolation of acidic gases in the near future.

Instability Mechanisms of Supported Liquid Membrane for Phenol Transport

The instability mechanisms of the supported liquid membrane using Celgard 2500 membranes as support and tributyl phosphate dissolved in kerosene as carrier for phenol transport was studied by ele.etroehemical impedance spectroscopy. Emulsion formation is demonstrated to be one of the main causes for the instability of supported liquid membrane in the present system. The emulsion-facilitated conditions, such as higher membrane liquid concentration, faster stirring speed, lower salt concentration and higher HLB value, would accelerate the degradation of supported liquid membrane. Other mechanisms including solubility and osmotic pressure work together to increase the membrane liauid loss.

Amorphous TiO_2-supported Keggin-type ionic liquid catalyst catalytic oxidation of dibenzothiophene in diesel

Supported ionic liquid(IL) catalysts [Cmim]PMoO/Am TiO(amorphous TiO) were synthesized through a one-step method for extraction coupled catalytic oxidative desulfurization(ECODS) system. Characterizations such as FTIR, DRS,wide-angle XRD, Nadsorption–desorption and XPS were applied to analyze the morphology and Keggin structure of the catalysts. In ECODS with hydrogen peroxide as the oxidant, it was found that ILs with longer alkyl chains in the cationic moiety had a better effect on the removal of dibenzothiophene. The desulfurization could reach 100% under optimal conditions, and GC–MS analysis was employed to detect the oxidized product after the reaction. Factors affecting the desulfurization efficiencies were discussed, and a possible mechanism was proposed. In addition, cyclic experiments were also conducted to investigate the recyclability of the supported catalyst. The catalytic activity of [Cmim]PMoO/Am TiOonly dropped from 100% to 92.9% after ten cycles, demonstrating the good recycling performance of the catalyst and its potential industrial application.

Recovery of Copper Ions from Wastewater by Hollow Fiber Supported Emulsion Liquid Membrane

Recovery of copper ions from wastewater using a hollow fiber supported emulsion liquid membrane (HFSELM) was studied with LIX984N as carrier, kerosene as diluents, and sulfuric acid solution as stripping phase. Effects of compositions of feed and emulsion liquid phase, flow rates on both sides of membrane, and hollow fiber module parameters were investigated. The stability of the emulsion liquid phase without surfactant and the effect of buffer in the feed phase on the extraction rate were also evaluated. It is found that the stability of the emulsion phase without surfactant is poor. Higher flow velocity gives shorter residence time for the emulsion liquid phase on the tube side, reducing the effect of particle coalescence on the separation process. The extraction rate increases with the increase of feed phase pH, carrier concentration, hydrogen ion concentration in the stripping phase, and ef- fective hollow fiber area. The phase ratio in the emulsion liquid phase has a negative effect on extraction rate. The flow rates on both sides have little influence on the extraction performance of the HFSELM, while buffer addition in the feed solution improves the extraction efficiency.

Gas-phase dehydrochlorination of 1, 1, 2, 2-tetrachloroethane over the non-metal supported ionic liquid catalyst

Developing of non-metallic catalyst to replace metal catalyst is a meaningful and challenging direction.In this work,the non-metallic catalyst was synthetized successfully by loading ionic liquid onto the silica surface,which was applied for the gas-phase dehydrochlorination of 1,1,2,2-tetrachloroethane.The 12%TPPC/SiO2(wt%)showed the best results with the conversion of 1,1,2,2-tetrachloroethane reaching 100%.The selectivity of 1,1,2-trichloroethylene was 100%,and no deactivation was found during the evaluation period.The catalytic mechanism was investigated and possible reaction route was given,which was a reference for fabricating and design of solid base catalyst.

Acetylene hydrochlorination over supported ionic liquid phase(SILP)gold-based catalyst:Stabilization of cationic Au species via chemical activation of hydrogen chloride and corresponding mechanisms

The activation of HCl by cationic Au in the presence of C2H2 is important for the construction of active Au sites and in acetylene hydrochlorination.Here,we report a strategy for activating HCl by the Au-based supported ionic liquid phase(Au–SILP)technology with the[N(CN)2^–]anion.This strategy enables HCl to accept electrons from[N(CN)2^–]anions in Au–[N(CN)2^–]complexes rather than from pure[Bmim][N(CN)2],leading to notable improvement in both the reaction path and the stability of the catalyst without changing the reaction triggered by acetylene adsorption.Furthermore,the induction period of the Au–SILP catalyst was shown to be absent in the reaction process due to the high Au(III)content in the Au(Ⅲ)/Au(Ⅰ)site and the high substrate diffusion rate in the ionic liquid layer.This work provides a facile method to improve the stability of Au-based catalysts for acetylene hydrochlorination.

Tb(III) Transport in Dispersion Supported Liquid Membrane System with D2EHPA as Carrier in Kerosene

The transport of Tb（III） in dispersion supported liquid membrane（DSLM） with polyvinylidene fluoride membrane（PVDF） as the support and dispersion solution including HCl solution as the stripping solution and di（2-ethylhexyl） phosphoric acid（D2EHPA） dissolved in kerosene as the membrane solution, has been studied. The effects of pH value, initial concentration of Tb（III） and different ionic strength in the feed phase, volume ratio of membrane solution to stripping solution, concentration of HCl solution, concentration of carrier, different stripping agents in the dispersion phase on the transport of Tb（III） have also been investigated, respectively. As a result, the optimum transport conditions of Tb（III） were obtained, i.e., the concentration of HCl solution was 4.0 mol/L, the concentration of D2EHPA was 0.16 mol/L, the volume ratio of membrane solution to stripping solution was 30：30 in the dispersion phase and pH value was 4.5 in the feed phase. Ionic strength had no obvious effect on the transport of Tb（III）. Under the optimum conditions, the transport percentage of Tb（III） was up to 96.1% in a transport time of 35 min when the initial concentration of Tb（IIl） was 1.0× 10 -4 mol/L. The diffusion coefficient of Tb（III） in the membrane and the thickness of diffusion layer between feed phase and membrane phase were obtained and the values were 1.82×10 -8 m2/s and 5.61 um, respectively. The calculated results were in good agreement with the literature data.

Study on transport of Dy(Ⅲ) by dispersion supported liquid membrane

The transport of Dy（III） through a dispersion supported liquid membrane （DSLM） consisting of polyvinylidene fluoride membrane （PVDF） as the liquid membrane support and dispersion solution including HCI solution as the stripping solution and 2-ethyl hexyl phosphonic acid-mono-2-ethyl hexyl ester （PC-88A） dissolved in kerosene as the membrane solution, was studied. The effects of pH value, initial concentration of Dy（III） and different ionic strength in the feed phase, volume ratio of membrane solution and stripping solution, concentration of HCl solution, concentration of carrier, different stripping agents in the dispersion phase on transport of Dy（III） were also investigated, respectively. As a result, when the concentration of HCI solution was 4.0 mol/L, concentration of PC-88A was 0.10 mol/L, and volume ratio of membrane solution and stripping solution was 40：20 in the dispersion phase, and pH value was 5.0 in the feed phase, the transport effect of Dy（III） was the best. Ionic strength had no obvious effect on transport of Dy（III）. Under the optimum condition studied, when initial concentration of Dy（III） was 0.8×10^-4 mol/L, the transport rate of Dy（III） was up to 96.2% during the transport time of 95 rain. The kinetic equation was developed in terms of the law of mass diffusion and the theory of interface chemistry. The diffusion coefficient of Dy（III） in the membrane and the thickness of diffusion layer between feed phase and membrane phase were obtained and the values were 1.99×10^-7 m^2/s and 15.97 μm, respectively. The results were in good agreement with experimental results.

Germanium transport across supported liquid membrane with Cyanex 923: Mathematical modeling

A mathematical model was developed to monitor the facilitated transport of germanium(IV) from oxalic acid solutions through a flat sheet supported liquid membrane(FSSLM) containing four trialkylphosphine oxides(Cyanex 923). The FSSLM modeling was based on the extraction constant(Kext) calculated from the liquid-liquid extraction(LLX) modeling. The LLX model presented a reliable calculation of the extraction constant(Kex= 2.057×103 L/mol4). The FSSLM model was solved using Matlab■ software according to extraction constant, Fick’s law, and diffusional principles. The model predicts the overall mass transfer coefficient(Korg) to be 3.84 cm/s. Using this value, diffusion coefficients(Dm) for various Cyanex 923 concentrations of 0.126, 0.252, 0.378, 0.505, 0.631 and 0.757 mol/L are found to be 8.50×10^-4, 4.30×10^-4, 1.87×10^-4, 5.87×10^-5, 2.57×10^-5, 2.09×10^-5 cm2/s, respectively. The results show that the diffusion rate of the current study is approximately more than that of similar FSSLM systems containing Cyanex 923 used to transport various metals. The modeling values are in good agreement with the experimental data, showing the good reliability of the mathematical model.

Comparison of conventional and supported liquid extraction methods for the determination of sitagliptin and simvastatin in rat plasma by LC-ESI-MS/MS

Three extraction methods were compared for their efficiency to analyze sitagliptin and simvastatin in rat plasma by LC-MS/MS, including （1） liquid-liquid extraction （LLE）, （2） solid phase extraction （SPE） and （3） supported liquid extraction （SLE）. Comparison of recoveries of analytes with different extraction methods revealed that SLE was the best extraction method. The detection was facilitated with ion trap-mass spectrometer by multiple reactions monitoring （MRM） in a positive ion mode with ESI. The transitions monitored were m./z 441.1→325.2 for simvastatin, 408.2→235.1 for sitagliptin and 278.1→260.1 for the IS. The lower limit of quantification （LLOQ） was 0.2 ng/mL for sitagliptin and 0.1 ng/mL for simvastatin. The effective SLE offers enhanced chromatographic selectivity, thus facilitating the potential utility of the method for routine analysis of biological samples along with pharmacokinetic studies.

Transport Study of Cu （Ⅱ） Through Hollow Fiber Supported Liquid Membrane

The transport of Cu(II)from aqueous solutions containing buffer media through hollow fiber supported liquid membrane(HFSLM)using di(2-ethylhexyl)phosphoric acid(D2EHPA)dissolved in kerosene as membrane phase and hydrochloric acid as striping phase was investigated.A set of factors were studied,including tube side velocity,shell side velocity,pH of the feed phase,Cu(II)concentration in the feed phase,buffer media concentration and D2EHPA concentration in the membrane phase.Experimental results indicate that the mass transfer coefficient increases with increasing both carrier concentration in the organic phase and flow rates on the tube side and shell side,and decreases with increasing initial Cu(II)concentration in the feed phase.With increasing pH value and acetate concentration in the feed phase,the mass transfer coefficient reaches a maximum value then decreases.The optimal operating conditions are obtained at pH value of 4.44 and 0.1 mol·L -1 acetic ion concentration in feed phase,and carrier volume fraction of around 10%in kerosene as organic phase.A mathematical model of the transport mechanism through HFSLM is developed.The modeled results agree well with the experimental ones.

Direct injection HILIC-MS/MS analysis of darunavir in rat plasma applying supported liquid extraction

A novel bioanalytical method was developed and validated for the quantitative determination of darunavir（DRV） in rat plasma by employing hydrophilic interaction chromatography and tandem mass spectrometry（HILIC-MS/MS） with supported liquid extraction（SLE）.lrbesartan（IRB） was used as an internal standard（IS）.The analyte in rat plasma（200 μL） was isolated through SLE using ethyl acetate as the eluting solvent.The chromatographic separation was achieved on Luna-HILIC（250 mm × 4.6 mm,5 μm）column with a mobile phase of 0.1% of formic acid in water：acetonitrile（5：95,v/v）,at a constant flow rate of 1.0mL/min.The MS/MS ion transitions for DRV（548.1→392.0） and IS（429.2→207.1） were monitored on an ion trap mass spectrometer,operating in the multiple reaction monitoring（MRM） mode.The lower limit of quantitation（LLOQ） was 0.2 ng/mL and quantitation range was 0.2-5000 ng/mL.The method was validated for its selectivity,sensitivity,carryover,linearity,precision,accuracy,recovery,matrix effect and stability.The method was successfully applied to pharmacokinetic study in rats.

Supported liquid membrane extraction to treat coal gasification wastewater containing high concentrations phenol

The hollow fiber supported liquid membrane extraction was introduced to treat coal gasification wastewater to recover phenolic compounds,with tributyl phosphate (TBP) as carrier,kerosene as the membrane solvent,sodium hydroxide solution as the stripping agent and PVDF as the membrane material. Factors having strong impact on the extraction efficiency were studied in detail,including the mass transfer mode,twophase flow rate,stripping phase concentration. As extraction system with 20% TBP-kerosene,parallel flow mass transfer,stripping phase concentration 0.1 mol/L,the optimal operating conditions could be obtained. Under the optimum operating conditions,the time required to reach equilibrium for the extraction is 50 min, and extraction efficiency of phenol is 86. 2% and the phenol concentration of effluent is 98.64 mg/L.

Transport of yttrium metal ions through fibers supported liquid membrane solvent extraction

A novel idea of transport of yttrium(Ⅲ) metal ions through fibers supported liquid membrane in two stage processes namely source to membrane and membrane to receiving phase has been proposed.The fibers supported liquid membrane was impregnated with different concentrations carrier.The experimental variables explored were concentration of yttrium(Ⅲ) ions,pH of source phase,PC-88A concentration in membrane phase,acid concentration in receiving phase and stirring speed.The pre-concentration of yttrium(Ⅲ) ions ...

Study on a Novel Disphase Supplying Supported Liquid Membrane for Transport Behavior of Divalent Nickel Ions

A novel d!sphase supplying supported liquid membrane （DSSLM）, containing supplying feed phase andsupplying stripping phase tor transport behavior ot NI（Ⅱ）, have been studied. The supplying supported feed phase included feed solution and di（2-ethyhexyl） phosphoric acid （HDEHP） as the carrier in kerosene, and supplying stripping phase included HDEHP as the cartier in kerosene and HC1 as the stripping agent. The effects of volume ratio of membrane solution to feed solution （O/F）, pH, initial concentration of Ni（Ⅱ） and ionic strength in the feedsolution, volume ratio of membrane solution to stripping solution （O/S）, concentration of H2SO4 solution, HDEHP concentration in the supplying stripping phase on transport of Ni（/I）, the advantages of DSSLM compared to the traditional supported liquid membrane （SLM）, the system stability, the reuse of membrane solution and the reten- tion of membrane phase were studied. Experimental results indicated that the optimum transpgrt of Ni（Ⅱ） was oh-tained when H2SO4 concentration was 2.00 mol＇L-＇, HDEHP concentration was 0.120 mol·L-1, and O/S was 4· 1 in the supplying stripping phase, O/F was 1 ： 10 and pH was 5.20 in the supplying feed phase. The ionic strength in supplying feed phase had no obvious effect on transport of Ni（Ⅱ）. When initial Ni（Ⅱ） concentration was 2.00x 10-4 mol/L, the transport percentage of Ni（Ⅱ） was up to 93.1% in 250 min. The kinetic equation was deduced in terms of the law of mass diffusion and the interface chemistry.

CO_2/N_2 separation using supported ionic liquid membranes with green and cost-effective [Choline][Pro]/PEG200 mixtures

The high price and toxicity of ionic liquids(ILs) have limited the design and application of supported ionic liquid membranes(SILMs) for CO_2 separation in both academic and industrial fields. In this work, [Choline][Pro]/polyethylene glycol 200(PEG200) mixtures were selected to prepare novel SILMs because of their green and costeffective characterization, and the CO_2/N_2 separation with the prepared SILMs was investigated experimentally at temperatures from 308.15 to 343.15 K. The temperature effect on the permeability, solubility and diffusivity of CO_2 was modeled with the Arrhenius equation. A competitive performance of the prepared SILMs was observed with high CO_2 permeability ranged in 343.3–1798.6 barrer and high CO_2/N_2 selectivity from 7.9 to 34.8.It was also found that the CO_2 permeability increased 3 times by decreasing the viscosity of liquids from 370 to38 m Pa·s. In addition, the inherent mechanism behind the significant permeability enhancement was revealed based on the diffusion-reaction theory, i.e. with the addition of PEG200, the overall resistance was substantially decreased and the SILMs process was switched from diffusion-control to reaction-control.

Methyl Cholate and Resorcinarene New Carriers for the Recovery of Cr(Ⅲ) Ions by Supported Liquid Membranes (SLM)s

The technique of supported liquid membranes was used to achieve the facilitated transport of Cr(III) ions, using tow amphiphilic carriers, the methyl cholate and resorcinarene. For prepared SLMs, toluene as organic phase and film of polyvinylidene difluoride, as hydrophobic polymer support with 100 μm in thickness and 0.45 μm as the diameter of the pores. The macroscopic parameters (P and J0) on the transport of these ions were determined for different medium temperatures. For these different environments, the prepared SLMs were highly permeable and a clear evolution of these parameters was observed. The parameter J0 depended on the temperature according to the Arrhenius equation. The activation parameters, Ea, ΔH≠ and ΔS≠, for the transition state on the reaction of complex formation (ST) , were determined. To explain these results for this phenomenon, and achieve a better extraction of the substrate, a model based on the substrate complexation by the carrier and the diffusion of the formed complex (ST) was developed. The experimental results verify this model and determine the microscopic parameters (Kass and D*). These studies show that these parameters Kass and D* are specific to facilitated transport of Cr(III) ions by each of the carriers and they are changing significantly with temperature.

Catalytic performance of acidic ionic liquid-functionalized silica in biodiesel production

Acidic ionic liquid([BsAIm][OTf]) was immobilized on sulfhydryl-group-modified SiO2(MPS-SiO2) via free radical addition reaction. The[BsAIm][OTf] loading on acidic ionic liquid-functionalized silica([BsAIm][OTf]/SiO2) was controlled through tuning the sulfydryl(SH)content of MPS-SiO2. All the samples were characterized by FT-IR, elemental analysis, N2adsorption-desorption measurements and TGDTA. The catalytic performance of [BsAIm][OTf]/SiO2in the esterification of oleic acid and the transesterification of glycerol trioleate for biodiesel production was investigated. The results showed that with the increase of [BsAIm][OTf] loading on SiO2the specific surface area and pore volume of [BsAIm][OTf]/SiO2decreased, and the pore diameter of [BsAIm][OTf]/SiO2narrowed. In the esterificaiton of oleic acid, the oleic acid conversion increased with the increasing [BsAIm][OTf] loading. In the transesterification of glycerol trioleate, with the increasing[BsAIm][OTf] loading the glycerol trioleate conversion decreased and the selectivities to glycerol monooleate and methyl oleate increased.